Zero point clamping system

VISCHER & BOLLI 07/447749/Z

Condition: excellent (used), Year of construction: 2002, x-axis 4000 mm y-axis 3500 mm z-axis 1500 mm Control SIEMENS 840 D w-axis 1500 mm column daylight 2500 mm surface area 3000 x 2000 mm workpiece weight 10000 kg spindle turning speed range 5-6000 U/min transmission ratio 2 power capacity - milling spindle 45 kW dist. cutter spindle - workpiece spindle 3500 mm max. torque on the spindle 1250 Nm tool change unit 200 -fach tool diameter 135 / 250 mm weight of tools max. 50 kg tool length - max. 400 mm tool taper ISO SK-50 the portal milling machine is in very good condition. Ncodpfx Ahovwgmmozet ADDITIONAL EQUIPMENT DRILLING/MILLING Angle milling head yes automatic tool clamping yes Tool clamping yes Ball screws yes Guideway cover yes Coolant system yes High-pressure cooling system (internal cooling) yes Full work area panelling yes Portal machining centre with tool changing system and second table top.

Condition: used, Year of construction: 2023, functionality: fully functional, travel distance X-axis: 14,000 mm, travel distance Y-axis: 4,500 mm, travel distance Z-axis: 1,900 mm, RepairFIT by Dornhöfer The Difference. Installation & Commissioning Included! Year of manufacture of the machine: 2023 Capacities / Travel distances: Nsdpfxjyu Szno Ahzoct Longitudinal (X): 14,000 mm Vertical (Y): 4,500 mm (*5,076.5) Cross (Z): 1,900 mm * Due to the two horizontal positions of the automatically indexing milling head, the vertical machining area can be extended by 576.5 mm. Table area (2 units): Length: 6,000 mm Width: 3,000 mm Number of T-slots on the table surface: 12 Width of T-slots: 22 mm Distance between slots: 250 mm FIBRO Rotary & Sliding Table: Dimensions: 3,000 x 3,000 mm Sliding axis: 1,500 mm Max. table load: 40 t Year of manufacture: 2002 Paint finish: RAL 7021 (black-grey) RAL 7035 (light grey) ref F-38 (DanobatGroup blue) Tool holder: ISO 50, DIN 69871 AD Big Plus Pull stud: DIN 69872 Form A Main drive: Drive type: SIEMENS main spindle motor with a 2-stage oil-cooled ZF gearbox Drive power: 100% duty cycle 53 kW (S1) Spindle speed range: Spindle speed: 20–4,000 min-1 Max. torque: at S1 – 100% duty cycle 1,531 Nm Max. feed force: X, Y, Z axis: 31,000 N Max. rapid traverse speed: X, Y, Z axis: 25,000 mm/min BASIC EQUIPMENT OF THE MACHINE: Heidenhain CNC control TNC640 High-performance orthogonal milling head Automatic tool changer (80 positions) Chip conveyor with floor discharge Coolant system with 20 bar & (IKZ) DYNAMICS ACTIVE STABILIZER+ "DAS+ SYSTEM" Cross-axis compensation Automatic milling head change system Operator platform Camera for workspace monitoring Pendulum machining package ACCURA HEADS Optimized Contour Milling (OCM) RepairFIT is our proven solution for a profitable entry into our product lines. Machines available in this line are sourced through a rigorous selection process and undergo a comprehensive inspection (deep-dive check). After thorough cleaning, any obvious defects or faults found are professionally repaired by our expert service team.

Condition: used, Year of construction: 2007, TECHNICAL DATA Travel X 760 mm Travel Y 510 mm Travel Z 610 mm Table clamping surface 1020 x 510 mm T-slots / table 5 x 18 mm x 100 mm Distance spindle to table min./max. 150/762 mm Spindle taper steep taper DIN 69871 ISO 40 Ncjdpjwud Afofx Ahzst Spindle speeds 10–10000 rpm Drive power (30 min/continuous duty) 11 kW Max. torque 236 Nm Constant power from 500 rpm Coolant tank 190 l Linear guides with ball bearings in X, Y, Z axes Rapid traverse X/Y/Z 30 / 30 / 20 m/min Feedrates programmable 3.0–7600 mm/min Positioning accuracy ±0.01 mm Repeatability ±0.005 mm Automatic tool changer (double-arm) 24 positions Internal cooling Chip conveyor

Condition: used, Year of construction: 2007, RA1784 Pallet rack system Galler OMEGA used 16600 x 5400 x 1350 mm Installation in a hall Shelf height: 5.400 mm shelf depth: 1.350 mm clear field width: 3.200 mm stored goods: pallets with stored goods Deep storage: 1,350 mm Storage arrangement: 1. stored goods on the floor 2. to 5 stored goods on pairs of tie bars, Shelf load on pair of spars at daylight Field width of 3.200 mm and : 2.100 kg shelf height 1.500 mm Field load: 8.4 to. at 1,500 mm buckling length (min. 4 fields) →Alle Loads are understood to be with evenly distributed load. Painting: Upright frame: Sendzimier galvanized Support beam: RAL 7035 light grey WITH RUST SPOTS (SUPERFICIAL) Installation: 1 pc. one-sided shelf axis, standing on a hall wall 5 x 3,300 + 100 = total length 16,600 mm consisting of: 6 pcs. stand frame Galler Omega screwed 5.400 x 1350 mm 40 pcs. carrier beam Galler Sigma 3.200 mm 80 pcs. safety pins Price net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, Würzburg Optional if required 2 pcs. ram protection corner used At the beginning or end and at passages to protect the shelf stem For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Nsdpek Abbbefx Ahzjct Your specialist and contact for intralogistics

Condition: used, Aufspannplatte - Tisch einer Langhobelmaschine - Tischbreite/Aufspannbreite: 1845 Tischlaenge/Aufspannlaenge: 5505 mm 7 T-Nuten laengs fuer T-Nutensteine: M 30 T-Nutenabstaende zueinander: 263 mm Gesamtlaenge: 6230 mm Plattenhoehe insgesamt: 350 mm Ncodpfobn Amfox Ahzot Gewicht: 11 t

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Ncodjvf E Avspfx Ahzot Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: like new (used), Year of construction: 2000, operating hours: 25,000 h, travel distance X-axis: 10,300 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,800 mm, feed rate X-axis: 10 m/min, feed rate Y-axis: 10 m/min, feed rate Z-axis: 10 m/min, position of the milling head: 2.5 x 2.5 °, spindle speed (max.): 3,000 rpm, spindle speed (min.): 60 rpm, table width: 3,300 mm, table length: 12,000 mm, mount diameter: 50 mm, total height: 48,750 mm, total width: 100,000 mm, total length: 212,000 mm, overall weight: 100,000 kg, Duplex milling are two machines located one opposite the other which can work seperately or as single machine, workpiece can be machined with 2 simultaneous spindles. Production increase of up to 50% in relation to conventional solutions, i.e. individual milling machines Nodpfxsrx Rxtj Ahzsct Improvements in part precision, by managing to do the machining of the part in one single setup, in most of the cases One sole operator can control the DUPLEX milling machines Reduced space and investment requirement comparing with two single machines Fast investment amortization due to the high productivity Duplex solution admits different configurations: single working area, pendulum working areas For machining excavator arms / boom like, CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo X-Axis: 10300mm Y-Axis: 2000mm Z-Axis: 1800mm Table Length: 12000mm Table Width: 3300mm Table load: 100000 Power on spindle: 22/30kW Spindle speeds: 60 - 3000Rpm Spindle Taper: 50ISO/Bt/Mk Feed rate X-Axis: 10000mm/min. Feed rate Y-Axis: 10000mm/min. Feed rate Z-Axis: 10000mm/min. Millinghead auto-index:2.5 x 2.5° Working hours: 25000H Length: 21200mm Width: 10000mm Height: 4875mm Weight: 100000kg

Condition: refurbished (used), Used modernised 3D CNC coordinate measuring machine. ZEISS Prismo 16 - second-hand system Equipment freely selectable . . Measuring machine in moving portal design Granite table Equipment can be arranged individually to your requirements. Further details on request Measuring range Njdewptpkopfx Ahzjct X =1600 mm - Y = 3000 mm - Z = 1000 mm Measuring accuracy: depending on the selected measuring system Price: on request - please let us know your equipment requirements ᐳᐳᐳ Single item - as long as available ᐸᐸᐸ Pease ask for our detailed offer. Of course, we provide all services such as installation, maintenance, service, training. Programming etc. as for a new machine

Condition: used, Year of construction: 2006, x-travel 1.250 mm y-travel 1.000 mm z-travel 1.000 mm Control MillPlus B-axis (head) -10 - +180 x 0,001 ° C-axis (table) 360 x 0,001 ° feed X/Y/Z/-axis 20 - 10.000 mm/min rapid traverse X/Y/Z 60,00 m/min tool taper HSK 100 spindle turning speed - stepless 20 - 10.000 U/min power capacity at 100 % load 25,00 kW power capacity at 40 % load 38,00 KW max. torque at 40% / 100% load 288 / 187 Nm table surface area Ø 1.100 mm table load 1,50 t toolpiece magazine: chain magazine 120 Stück tool diameter 110 mm tool diameter with 2 vacant positions 230 mm Ncodsyui Ncepfx Ahzet tool length - max. 500 mm weight of tools max. 30,00 kg rotary table speeds infinitely variable 10 - 500 U/min total power requirement 85,00 kW weight of the machine ca. 25,00 t dimensions of the machine ca. 9,00 x 6,50 x H3,50m m 5-axis turning/milling machining center with MillPlus IT FD control; dual pallet changer; coolant system; coolant through the spindle; chip conveyor; rotating viewing window; electronic handwheel. Spindle new 10/2025 Turning-table overhaul 2022

Condition: good (used), Year of construction: 2007, Machine is in good working condition. Machine come without automatic line. Njdpfxsxf Iamo Ahzjct Marked equipement with red not come.. Some accesories and machine equipement are also available. More specs of the machine, check last two pictures.