Thread cutting head 13 pieces

WMW A2 MK3

Condition: new, Year of construction: 1993, Ground plates 750mm, monoblock boom, 1 direct-mount bucket, ready for operation, display is unreadable, machine is 3.15m wide. Bjdpozkz Twefx Al Aeln

Condition: used, machine/vehicle number: 7979, Table diameter: 400 mm Table with 8 T-slots: 12 mm Overall height: 175 mm Bodpfx Alob Ez R Uj Ajln Space required: 600 x 450 x 175 mm Weight: approx. 100 kg

Condition: used, Year of construction: 1983, Bohrleistung in Stahl (-Ø 50 mm throat 1500 mm workpiece height max. 1380 mm Bohrleistung in Guß (-Ø 60 mm Abstand Spindelmitte bis Säule 320 - 1250 mm swival range +/- 180 ° base plate surface area 2640 x 1000 mm max. torque on the spindle 310 Nm Bohrspindel-Ø/ Aufnahme 75 mm /MK 5 bore spindle stroke 310 mm spindle turning speed range 28 - 2500 U/min feed: 0,05 - 2 mm/U power capacity 4 kW Blsdpfx Alotv Ikle Ajn weight of the machine ca. 4,3 t dimensions of the machine ca. 3,2 x 1 x 2,75 m cube table 500 x 500 x 500 mm

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, sheet thickness (max.): 60 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), Equipment: cone bending device, documentation/manual, 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls 570 / 500 / 430 mm Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Blodpfxezbqquj Al Aon Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, faceplate diameter 3100 mm Bodpfx Aeyqt Hdsl Asln swing diameter 3600 mm turning height 3600 mm control Fagor 8035 table load 35 t turning speeds 0,32 - 40 U/min max. ram stroke 3000 mm table load 35 t turning speeds 0,32-40 U/min total power requirement 70 kW 2x Ram head 250 x 250 mm Chip conveyor Mist extraction unit Coolant system The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: excellent (used), functionality: fully functional, Year of construction: 2000, machine/vehicle number: 3roll 3500x140 mm prepinch, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: MG, controller model: MG, number of rollers: 3, roller (bottom) diameter: 880 mm, roller (top) diameter: 950 mm, side roll diameter: 880 mm, roller length: 3,550 mm, working width: 3,500 mm, working height: 3,950 mm, sheet thickness (max.): 140 mm, sheet thickness steel (max.): 175 mm, overall weight: 200,000 kg, total length: 8,800 mm, total width: 5,100 mm, total height: 5,775 mm, power: 200 kW (271.92 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, Hydraulic Plate Bending machine planetary pinch pyramid with prebend. model MG35140V 3 roll capacity 3500x140 mm The machine was overhauled in 2024, Capacity : Plate width mm. 3500 Blsdpeyzim Aefx Al Aen Plate thickness mm. 140 Capacity chart in enclosed Tech data: -3 rolls driven hydraulic motorized with axial gear unit on each roll independent -Synchronized hydraulic rotation of the 3 rolls with variable speed. -Planetary design with pre-pinch fully hydraulic -Conical plate bending with hardened contrast pad -Digital position readouts of the bending rolls -Rolls installed on bearings double crown heavy duty -Overload safety hydraulic operation protection of the 3 rolls -High pressure hydraulic power pack with multi-pumps oil feed -Centralized control panel electric on wheels with joysticks and digital readouts -Emergency stop with safety system around the machine working area Rolls surface length mm. 3550 Top roll mm. 950 Side rolls mm. 880 Electric power on hydraulic unit Hp 100 + Hp 100 Voltage 380 Vac / 50 Hz Configuration & accessories installed with the machine -Hardened surface of the 3 rolls -Conical plate bending attachment , rolls tilt with contrast roller type. -Centralized operator panel with directional joysticks electric. -Digital position readout of the bending rolls. -Emergency and safety installations, certified CE -User manuals and instruction books in English -Dimension see layout drw in enclosed

Condition: excellent (used), Year of construction: 1984, functionality: fully functional, turning diameter over cross slide: 630 mm, spindle bore: 320 mm, turning diameter: 1,200 mm, turning diameter over bed slide: 930 mm, turning length: 3,000 mm, Lathe in very good technical condition, has seen very little use and was not used for machining pipes. The Poręba TPL 90/3m lathe (also listed in market nomenclature as a variant of the TPK 90 series) is a textbook example of an Oil Country Lathe / Hollow Spindle Lathe. This model fulfills all the specific criteria for machines intended for the Oil & Gas sector: • Massive spindle bore (Big Bore): This version features a spindle bore with a diameter of 320 mm (approx. 12.5 inches), allowing for easy insertion of thick-walled drill and casing pipes. • Dual chucking system: The headstock is designed for mounting two independent lathe chucks (front and rear, typically 28 inches in diameter), ensuring the pipe is clamped and stabilized at both ends of the spindle. • Optimal working dimensions: The 3m designation defines a turning length between centers of 3000 mm, which, combined with a swing over bed of 930 mm (hence the "90" in the name), allows for machining heavy-duty pipeline components. • Exceptional rigidity: FUM POREBA factory machines are renowned for their monolithic, very wide and heavy cast iron beds, which effectively dampen the immense vibrations generated during taper thread cutting. Bsdpfxoy Sf Aze Al Asln In international used machinery catalogues, this specific Poręba model is directly classified under the Oil Field Lathes category. TECHNICAL SPECIFICATIONS: Geometric parameters and machining ranges • Swing over bed: 930 mm / 36.6 in • Swing over cross slide: 630 mm / 24.8 in • Swing in gap: 1200 mm / 47.2 in • Maximum turning length between centers: 3000 mm / 120 in • Bed width: 585 mm / 23.0 in Headstock • Spindle bore diameter (Hollow Spindle): 320 mm / 12.6 in (in US nomenclature classified as a 12.5" version) • Spindle speed range: 5 – 250 rpm, or modified versions up to 710 rpm • Number of spindle speed steps: 18 Feed and thread cutting system • Longitudinal feed range: 0.1 – 12.8 mm/rev / 0.004 – 0.504 in/rev • Cross feed range: 0.05 – 6.4 mm/rev / 0.002 – 0.252 in/rev • Types of threads cut: Metric, Inch (Whitworth), Module, Diametral Pitch (DP) Tailstock • Tailstock quill diameter: 130 mm / 5.1 in • Tailstock quill travel: 300 mm / 11.8 in • Internal taper of quill: Morse No. 6 (MT6) Drive and dimensions • Main motor power: 22 kW / 29.5 HP • Overall length: approx. 5500 mm / 216.5 in • Overall width: approx. 1750 mm / 68.9 in • Overall height: approx. 1500 mm / 59.0 in • Total weight: approx. 8000 kg / 17,630 lbs

Condition: new, Year of construction: 2025, Ref. -No.: 10461 Manufacturer: IGREK Type: DT 4000 Year of construction: 2025 Type of control: CNC-Steuerung Control: SIEMENS SINUMERIK 840D SL Storage location: Istanbul Country of origin: Türkiye Spindle Speeds: 4000 RPM Turning Height: 2000 mm Table Diameter: 4000 mm Spindle power: 37 kW Max. Table load: 40 t Rotate table rotation speed: 60 RPM Max. Turning diameter: 5000 mm Max. Turning height over faceplate: 2000 mm Blodpfxjxmd Sue Al Aen Max Spindle Torque: 1200 Nm Spindle Taper: ISO 50 Machine length: 7500 mm Machine width: 12000 mm Machine Height: 9500 mm Weight Of The Machine Ca.: 125 t Further information: Ram Slide Stroke: 2100 mm Ram Section: 350 x 350 mm Vertical Travel of the Moving Traverse: 2000 mm Table Drive System: Segmented Direct Drive Motors Table Torque: 8200 Nm - 14400 Nm max. Table Guide System: Hydrostatic Bearing and Guides IGREK DT 4000 – Your solution for precise heavy-duty machining The IGREK DT 4000 is a state-of-the-art CNC vertical turning center designed specifically for the precise machining of large components. Equipped with a 4,000 mm hydrostatic rotary table and a movable crossbeam, it enables the efficient machining of workpieces with a maximum turning diameter of 5,000 mm and a turning height of up to 2,000 mm. Key features: Hydrostatic rotary table: The 4,000 mm rotary table with hydrostatic bearing ensures maximum precision and smooth running when machining heavy workpieces. Movable crossbeam: The vertically movable crossbeam with a stroke of 2,000 mm offers flexibility and allows adaptation to different workpiece heights. Powerful spindle: With a spindle speed of up to 4,000 rpm and a power of 37 kW, the machine is designed for demanding machining tasks. High load capacity: The rotary table can accommodate workpieces weighing up to 40 tons, enabling the machining of large and heavy components. Multifunctional machining: Thanks to the live spindle and the precise positioning of the C-axis, milling and drilling operations are possible in addition to turning, which increases the versatility of the machine. The IGREK DT 4000 combines advanced technology with high performance and flexibility to meet the requirements of modern manufacturing processes. Its robust construction and wide range of machining options make it the ideal solution for the precise machining of large components in various industries.

Condition: used, Modular milling cutter Bodpfx Aledklt Ns Asln Module 8 20 degrees Length 1800 mm Diameter 120 mm Inner diameter 40 mm

Condition: good (used), Year of construction: 1999, functionality: fully functional, turning length: 3,000 mm, turning diameter: 1,000 mm, spindle bore: 197 mm, Upon request, videos of the machine in operation can also be provided. Bjdpfx Ajyr N N Rjl Aeln Maximum turning length: 6000 mm Turning diameter: over cross slide: 1000 mm over bed: 1250 mm Spindle bore: 197 mm Spindle speeds: 0 – 665 rpm Faceplate diameter: 1200 mm Workpiece weight: 15000 kg between centers Motor power: 55 kW / 74 hp 3 gear stages: 1.5-55 / 50-180 / 180-665 rpm Accessories: Sauter 4-position tool turret (rotation defective) Tailstock (hydraulics partially defective, pressure loss) Chip conveyor 2 chip guard doors (incl. safety device) 4-way bed machine (flat bed) LED lighting