Used bale presses for sale (212)

Condition: reconditioned (used), Year of construction: 2015, operating hours: 28,748 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), volume flow: 350 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Dsdovn Tg Ijpfx Adajcp Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 5536, pressing force: 50 t, filling opening width: 1,252 mm, filling opening length: 1,100 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 500 kg, total width: 3,000 mm, total height: 3,000 mm, total length: 9,500 mm, feed length X-axis: 1,200 mm, feed length Y-axis: 1,200 mm, feed length Z-axis: 1,200 mm, type of input current: three-phase, input voltage: 400 V, input current: 100 A, overall weight: 16,000 kg, noise level: 80 dB, pressure: 250 bar, pressure (max.): 250 bar, opening width: 1,100 mm, control cabinet height: 1,700 mm, control cabinet width: 700 mm, control cabinet length: 900 mm, oil tank capacity: 600 l, power: 45 kW (61.18 HP), empty load weight: 16,000 kg, volume flow: 16,000 m³/h, operating pressure: 200 bar, transport width: 3,000 mm, protection type (IP code): IP55, Equipment: compressor, documentation/manual, Presona LP50VH3, and as a bonus, you also get the Presona PP1500-500. The PP1500-500 is actually an auxiliary device used for specific tasks, such as precise cutting or additional processing of material, which the base machine itself does not handle. So the PP1500-500 is there to allow you to perform additional specialized operations that the main machine cannot do. Dsdpfxoxfr Als Adaocp

Condition: good (used), Welger Type: RC 660 Roller compactor with Brück suction Compact and fully automatic Used exclusively for producing pressed bales from low-density packaging materials. Application variants Press materials Dedpfx Adjdtxbijaocp Paper edge trimming (strips and endless) Paper and film bags PP film edge trimming Film strips Clothing protection film (PP/PE films) PP/PE fiber material Insulating and nonwovens Foam mesh Packaging foam Tetrapak Length 2100mm, width 940mm, height 1755mm Dimensions of filling shaft 330 mm x 600 mm Bale format max. 400 mm x 600 mm Bale weight 20 - 30 kg depending on the material being pressed Press density 250 - 400 kg/m³ depending on the material being pressed Throughput daily output 30 bales / day Feed speed 0.36 m/s RC 660 3X 400V 50Hz 16A 2.2 kW 5.0A 700 kg Brück extraction Series: KFA Size: 60-30-3000 Air output: 6,000 m³/h Motor output: 0.3 kW Filter area: 30 m² Negative pressure: 3,100 Pa Condition: used Scope of delivery: (see picture) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have over the phone.

Condition: good (used), - Large filling opening, ideal for large boxes - Container tipper for convenient filling Pressing force in kN: 400 Bale length: 1,100 mm Bale width: 750 mm Bale height: 750 mm Press length: 5,640 mm Press width: 1,674 mm Press height: 2,500 mm Weight: 4,450 kg - Motor power in kW: 9 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 350 kg - Manual binding: 3 times with wire Year of manufacture: 2013 HSM HL 4010 LI baler - Large filling opening, ideal for large boxes - Container tipper for convenient filling Pressing force in kN: 400 - Motor power in kW: 9.5 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 350 kg Dcodpov Amv Ejfx Adaop - Manual binding: 3 times with wire Year of manufacture: 2012

Condition: used, Year of construction: 1995, functionality: fully functional, input voltage: 400 V, power: 40 kW (54.38 HP), Baler from 1995. Viewing by appointment only. Dcsdpfx Aow H Ar Aedasp

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Djdpokcgynofx Adajcp Hours 43.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Djdpfju Thhrex Adaocp Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Manufacturer: Comp Tip: SB5 Engine: 2,2 KW Dcsdpfx Adsh Eic Aoaep Cylinder stroke length: 500 mm Chamber size: 500 x 350 x 400 mm

Condition: excellent (used), functionality: fully functional, Safe Waste Compactor Hydraulic waste compactor that compresses directly into the waste storage container, easily adaptable for standard 1100, 660 (or 770*) litre, 4-wheeled, lidded – most often green – bins (Sulo, Otto, Schäfer, etc.). For bagged and bulk waste Compression ratio is between 1:4 and 1:8 depending on the waste composition, saving approximately 75% in waste transportation costs. Safe design ORWAK bin compactors are robust and can be operated safely. During compaction, it is not possible to reach inside the machine, ensuring operator safety. Both external and internal surfaces are easily accessible for quick and simple cleaning. The waste compactor can be used with all types of standard 1100, 660 (or 770*) litre plastic waste bins, whether with flat or semicircular lids! We can assist with transportation. Dcsdpfx Asxmbg Njdasp

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Drive power: 31.5 kW Pressing force: 60 t Dcodpev Amw Njfx Adajp Bale weight (depending on material): 350–600 kg Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Pressing/cycle time: 13/24 s Machine weight: 7000 kg

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, Baler Orwak Compactor 3150 Very good condition Dcodpfx Ajw Rn U Nodaep

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Dsdpokcgf Hofx Adajcp Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 22,000 kg, oil tank capacity: 900 l, For sale is a complete baling system consisting of conveyor technology, baling press and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical Throughput rate at a bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Comments: Dsdpjviwdmofx Adaecp The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: good (used), Manufacturer: MBT Tip: MV-250 S Motor: 5,5 kW hopper size: 780 x 600 mm Dcjdpfx Aohzr U Isdajp Housing size: 3500 x 1000 x 2200 mm

Condition: used, Year of construction: 2014, pressing force: 122 t, overall weight: 40,000 kg, pressure: 315 bar, Machine has been used but is surplus and therefore for sale! Dodpewa N U Dsfx Adascp

Condition: ready for operation (used), Model: HSM V-Press 1160 Plus Baler Pressing force (kN): 532 Djdpora Nyuefx Adaecp Output (bales/h): 1–2 Max. bale size (mm): 1200x1100x1000–1200 Dimensions (L x W x H) (mm): 1780x1150x2985 Power (kW): 7.5 Year 2007–2008 price €5,500 year 2009–2010 price €5,800 year 2011–2013 price €6,300 We also offer HSM V-Press 1160 Max balers, year 2014–2015 Weight (kg): 2,300 ALSO AVAILABLE: 2017–2018 models – €7,500

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, pressing force: 50 t, Fully functional Bramidan B50 baler, serviced, complete set - hook, strap rolls. Dcodpfx Ajxg Tk Tedaep

Year of construction: 2008, condition: good (used), Horizontal baling press Build in 2008 Bale size 800x1000x1400 Dcodpfxjg Ibt Ns Adaep Loading height 1250mm

Condition: reconditioned (used), Year of construction: 2002, operating hours: 43,954 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, overall weight: 50,800 kg, oil tank capacity: 3,100 l, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002 Operating hours 43,954 hours, stand March Press power main press 200 tons Specific press capacity 16,5 kg/cm² Dcjdpfeu Thgzox Adasp Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 112 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine is currently in our workshop for overhaul. We assume that the press will be completely overhauled in approx. 4 weeks and can then be tested. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, filling opening width: 1,200 mm, filling opening length: 1,600 mm, bale width: 300 mm, bale height: 300 mm, total width: 4,600 mm, total height: 2,244 mm, total length: 6,130 mm, input voltage: 380 V, overall weight: 16,500 kg, power: 55 kW (74.78 HP), Equipment: documentation/manual, Bale clamp 300 x 300 mm. Very good condition. Well maintained. Dsdpfoxcazwox Adaecp

Condition: ready for operation (used), Bramidan 4-0F Motor: 4 kW Press dimensions: 250 x 100 x 255 cm Bale dimensions: 1100 x 700 x 950 mm Bale weight: 200–250 kg Pressing force: 18 tons Weight: 1580 kg Dcsdpfxjv Ai Uqe Adaep This machine is used to reduce the volume of waste such as film, cardboard, etc. We also have a Bramidan 3-chamber baler available.

Condition: good (used), B5 – Ideal for large cartons: High throughput – large capacity Bale is ejected automatically Strap rollers positioned at the front for easy strap replacement Cardboard bale weight (kg): 80-110 Plastic film bale weight (kg): 90-130 Bale size WxDxH (mm): 1000 x 700 x 800 Pressing force (t): 5 Power supply: 1x230V 50Hz 10A Motor (kW): 1.1 Noise level (dB): 65-68 Dcsdpfx Asv Aktnodajp Average cycle time (sec): 33 Dimensions WxDxH (mm): 1360 x 895 x 2370 Weight (kg): 600 Feed opening W x H (mm): 1000 x 500 Year 2015-16 price: 4000 EUR Year 2014 price: 3500 EUR

Condition: ready for operation (used), Baler Hsm vk 42/1200 fully automatic Pressure force: 42 tons Beam dimensions: 700 x 800 x 600 - 1200 mm Beam weight: approx. 450 kg Press length approx. 7 meters Dcsdpfsra Nrxox Adasp press weight approx. 6000 kg tying 4 x wire automatically

Condition: good (used), Bramidan B 20 Baler Bale dimensions – WxDxH (mm): 1200 x 800 x 800 Feed opening WxH (mm): 1200 x 480 Pressing force: 20 tons Motor (kW): 4.0 Cycle time (s): 36 / 21 Baler dimensions WxDxH (mm): 1775 x 1030 x 2790 Weight (kg): 1600 Stroke (mm): 750 Number of tying points: 4 Year of manufacture: 2012 – 2017 Bramidan X25 – High-performance baler for waste compaction Suitable for various materials, including stretchable types Large, wide chamber Dsdpev Aku Sefx Adajcp Retaining clamps prevent material expansion inside the chamber Short cycle times allow for rapid waste processing TYPES OF WASTE: Cardboard Plastic film Paper PET bottles Aluminum cans Rigid plastics Textiles EPS foam Steel cans BALE DIMENSIONS 1200 x 800 x 800 mm PRESS FORCE 25 t BALE WEIGHT Cardboard (kg): 200-300 Plastic film (kg): 250-350 Year of manufacture: 2012–2018 Price: 5,500 EUR

Condition: excellent (used), Manufacturer: Strautmann Model: PP 1207 Plus Bale size (LxWxH): 1200 x 1100 x 730 mm Bale weight: approx. 400 - 500 kg External dimensions (LxWxH): 1850 x 1047 x 3079 mm Transport height: 2500 mm Filling opening: 1190 x 600 mm Pressing force: 59 t / 580 kN Performance: 1 - 2 bales/hour Number of ties: 4 Dedpfjv Aiymox Adaecp Press weight: 2300 kg Power supply: 400 V / 50 Hz Power consumption: 4 kW Installation location: sheltered indoor/outdoor Noise level: less than 80 dB(A) Year of manufacture: 2003–2007 I also have Strautmann PP 1207 balers from 2010–2011, price 5500 EUR I also have Strautmann PP 1208 balers from 2014–2015