Used mandrel tube bending machines for sale (47)

Condition: used, Semi-automatic tube bending machine, mandrel tube bender MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Serial No. Year of construction for simultaneous bending of two steel tube sections up to Ø 12 mm Bending angle max. 90° Tube diameter max. 12 mm Mandrel length approx. 65 mm Rated power 3.5 kW Crsdpfx Ajpu R Nvsdaji Compressed air max. 6 bar / approx. 1 litre per bending cycle Power supply 400 Volt, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Angle input control via STÖBER Controlbox Series 4000/5000 - SIEMENS S7-200 control with TD200 display - Machine without bending tools and without tool storage pins 25 x 183 mm - Only 1 bending mandrel available (see pictures). Required space (L x W x H) 1000 x 1000 x 1500 mm Weight 390 kg Good condition

Condition: used, Ring bending machine, profile bending machine, bending machine, pipe bending tool, tube bender, tube bending machine, mandrel bending machine Credpfoh S Ti Esx Adaoi -Mandrel bending machine: mechanical profile bending machine -Accessories: see photos -Total dimensions: 1200/740/H1220 mm -Weight: 169 kg

Condition: used, Mandrel Tube Bending Machine 42 Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 Crsdpfxewnrt Se Adaji D - 44143 Dortmund - Wambel

Condition: good (used), Year of construction: 1996, tube diameter 6 - 28 mm wall strength 2 mm bending radius min. 2 x D Control IPU 20 bending radius max. 5,0 x D mm bending angle max. 190 ° arbor length 3000 mm operating pressure 180 bar hydraulic motor 4 kW weight of the machine ca. 900 kg dimensions of the machine ca. 3,8 x 1,1 x 1,3 m Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut. Mandrel lubrication, adjustable length stops. Cjdpfsvtgn Njx Adaori Operating modes: MANUAL and semi-automatic. Control buttons: hydraulics on / off, operating mode selection, clamp to / on, clamp forward / backward, mandrel forward / backward, bending forward / backward /, locking forward / backward, mandrel lubrication, turning device forward / backward, plate reset, length stop forward, emergency stop. The machine comes from a prototype construction and was only used a little until 2000. After that, the machines of this department were sold. However, the purchaser did not use the pipe bending machine and therefore it has only stood in the warehouse and has not worked since then ((original paint). Please notice that the price of a new machine today is over € 60.000,--. Machine dealer with own stock of 1600 m².

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2006, operating hours: 83,700 h, machine/vehicle number: 0126427-027, Equipment: type plate available, LVD STRIPPIT GLOBAL 30 1225 Turret Press Machine in very good technical condition, used at Alsanit. Regularly serviced only by the manufacturer's service. Service parts used in the service - only new and original. The turret press is in continuous production use. If you are interested, we encourage you to make an appointment to confirm the technical condition and technological capabilities of the offered machine. It is possible to provide a video presenting the operation of the turret press, please send an inquiry with a request for sharing. General data: Location: Alsanit Sp. z o.o., ul. Wieleńska2, 64-980 Trzcianka, Poland Province: Wielkopolskie Year of production of the turret press: 2006 Date of purchase and installation of the machine: June 2019 Machine mileage: 83700rh Maximum pressing force: 300 kN (30 tons) Maximum sheet thickness: 6.4 mm Turret system type: Thick Turret Control unit: CNC :GE FANUC 180 IP Maximum travel in the X axis: 2,576 mm Maximum travel in the Y axis: 1,337 mm Maximum table load (even): 145.6 kg Simultaneous speeds: 110 m/min Number of strokes per min (die fi 25 mm); ±2% 400 min-1 Number of strokes per min ("nibbling" function - 2 mm): 1000 min-1 Number of strokes per min (marking/0.5 mm): 1700 min-1 Maximum feed rate (speed) in the X axis: 83 m/min Maximum feed rate (speed) in the Y axis: 73 m/min Number of tool sockets (stations) in the turret: 30 pcs. Station A – max. diameter 12.7 mm: 8 pcs. Station B – max. diameter 31.7 mm: 16 pcs. Station C – max. diameter 50.8 mm: 2 pcs. Station D – max. diameter 88.9 mm: 4 pcs. Number of indexed (rotary) stations in the revolver: 4 pcs. (D stations) Note: A multitool can be placed in each D station (1 multitool has 3 to 8 tools), which increases the number of tools from 12 to 32 pcs. Machine height: 2,325 mm Machine length: 5,584 mm Machine width: 5,160 mm Machine weight: 13,750 kg Crjdpfxewptduj Adaei Working sheet size: 1,250 x 2,500 mm Number of sheet metal clamps (individually programmable): 3 pcs. Tilting work chute for cut parts: 450 x 500 mm Electric power supply 380/415 Volt, 35.5 kVA, 63 A, cable cross-section (3+1)x16 mm2 Additional equipment: Waste conveyor; Brush table The LVD Strippit Global 30 punching machine has 4 programmable rotary stations (size D). Each station can be equipped with a multitool head with automatic rotation. Using a servo drive, as well as CNC control - both the rotary stations and the entire turret have the possibility of bidirectional rotation with an accuracy of 0.01 degrees. The Auto Index rotary stations of the LVD Strippit Global 30 punching machine operate on the principle of direct drives, which are located directly above the station, constituting part of the turret mechanism. In the rotary stations with a diameter of 88.9 mm, a multitool tool holder can be mounted, thus increasing the machine's capabilities and the number of tools. The multitool holders allow for the installation of 3 or 8 punches and dies with a diameter of 12.7 mm or 31.7 mm, respectively. We issue a VAT invoice The price given is a net price!

Condition: used, functionality: fully functional, Year of construction: 2005, operating hours: 142,500 h, pipe diameter (max.): 50 mm, pipe length (max.): 2,000 mm, bending radius (max.): 150 mm, tube bending machine, SPS bending machine, tube bender, tube bending system, tube processing, tube technology, electro-hydraulic, mandrel bending machine Capacity: - Round tubing mild steel Ø 50 x 3,0 mm - Round tubing stainless steel Ø 50 x 2,0 mm - Max. moment of resistance 5,0 cm³ - bending angle up to 180° + 10° overbend Machine equipment-/basic accessories: - Tube insertion length/usable length 2000 mm - Max. bending radius 150 mm - Bending height 1050 mm - Free-standing bending head, length 850 mm - The free-standing bending head is so compact that tubes can be processed with a clear spacing of 400 mm between two bends Crsdpfewzammex Adaei - Electrohydraulic drive - With automatic cycle; one of the following modes can be selected via key switch - Function activiation via hand switch - In manual operation mode, all functions can be operated via push button in jog mode - In semi-automatic mode, the tube is clamped after the first activation, bent after the second activation, and then the machine returns to its initial position - Counter bearing opens wide, so that with the corresponding equipment (VWE A-642) the rotation unit can move up to just behind the bending tool - Bending direction counter-clockwise - With hollow shaft to achieve small radii - For radii from 1x tube diameter - Manual tool reset - Automatic tool locking - All functions hydraulic - Operation via push button - Standardized hydraulic components - Stationary machine - Color: RAL 7037 dust grey, RAL 3000 red Machine data: - Nominal pressure: 250 bar, operating pressure: 200 bar - Operating voltage: 400 Volt – 50 Hz – 3 phase – 7.5 kW - Length: 3200 mm - Width: 1400 mm - Height: 1300 mm - Weight: approx. 1470 kg

Condition: used, Year of construction: 2012, tube diameter 51 mm wall strength 3 mm Credpfxspunglj Adasi semi-automatic operated UZMA bending radius max. 225 mm bending angle max. 190 ° bending speed 35 ° / sec. mandrel length 3.100 mm engine output 5,5 kW voltage 380 V total power requirement 11,0 kW weight of the machine ca. 1,36 t dimensions of the machine ca. 4,20 x 1,60 x 1,20 m - Serial No.: 0144 - semi-automatic mandrel bending machine - bending angle is program controlled - length + twisting angle manually adjustable - digital display for twisting angle, length and bending angle - the following bending sets are included: 1.) R75 mm / Ø 20 mm 2.) R60 mm / Ø 25 mm 3.) R75 mm / Ø 30 mm 4.) R75 mm / Ø 40 mm 5.) R170 mm / Ø 50 mm 6.) R35 / flat Material 40 x 10 mm

Condition: new, Year of construction: 2025, THE ECONOMICAL MANDREL BENDING MACHINE FOR TIGHT BENDING RADII. For tube dimensions from 20 - 90 mm, this bending system offers solutions for complex geometries with standard radii of 2xD. Depending on material quality and wall thickness ratio, radii of 1.5xD can also be realized suitable for series production. With a tool height of 120 mm, there are also sufficient options for special profiles. The extremely precise and powerful electric drive of the bending axis as well as the stable and rigid construction of the mandrel carrier and the bending arm also contribute to the desired bending result. The plug-in bending tools allow a quick changeover to other tube dimensions. The clamping pressure for the tube clamping can be optimally adjusted. The PLC control (can be expanded as required via USB stick) with data memory and the latest X2X interface can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for a maximum of 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The control system has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. Also available with pneumatic rotation stop or with gear-assisted length and twist positioning. POSSIBLE AREAS OF APPLICATION: - Plant engineering, e.g. chemistry - hydraulic piping - metal construction- prototype construction- pipeline construction TECHNICAL DATA: Bending capacity 7000: Ø 20 to 70 x 5 mmbending capacity 9000: Ø 20 to 90 x 5 mm depending on the material- bending radius min/max: 40 mm/250 mm- Bending radii min: 1.5 x Ø (standard 2 x Ø ) - Multifunction machine control Bending angle adjustment (0,1°) - Mandrel support lengths 3000/4500/6000 mm - Maximum 180º bending result - Weight 1600-3200 kg (depending on version) - Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: - Automatic mandrel lubrication (minimum quantity) - Pneumatic or hydraulic quick chuck Cjdpfx Aenh R Suodaeri - Larger bending radius up to 300 mm - Positioning of the length and twist via automatic brake function or via manual stops by foot switch - Semi-automatic positioning of the length and twist via servo motors - Automatic tool retraction - Pipe calculation software - 10 inch touch screen with integrated tube calculation - Data transfer via cable (LAN), via radio (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing purchase via - the company JUTEC - Service contracts, maintenance at your site

Condition: new, "Properties: Bending radii: R36 to R190 (min. R= 2xD) Max. Bending speed: 2.8 rpm Control: digital Number of programs: 1 Dimensions (W x H x D): 245 x 300 x 320 mm Weight: 23 kg Portable Csdpfjuudi Asx Adaori Power: Hard copper and aluminum : 42 x 1.5 mm Steel tube : 38 x 1.5 mm Stainless steel : 35 x 1.5 mm Solid material : 20 mm Scope of delivery MD070M Standard accessories (e.g. foot switch, operating instructions)"

Condition: like new (used), functionality: fully functional, Year of construction: 2024, Manual length and angle positioner for 6000 mm pipe length The bending capacity can be found in the attached technical documentation in PDF format. Crjdpfx Aev Tz S Asdaji

Condition: good (used), functionality: fully functional, Year of construction: 1998, bending radius (max.): 600 mm, mandrel length: 1,200 mm, wall thickness: 8 mm, Transfluid DB 40100ST Mandrel bending machine Tube bending machine The above machine is a mandrel bending machine designed exclusively for the production of tubes and profiles with an outer diameter of 40-100 mm, max. 110x5 mm with a max. wall thickness of 8 mm or for the processing of solid materials with an outer diameter of up to 70 mm. Pipe push-on length/usable length: 1200 mm Radius range max:600 mm Codpfsr H Havsx Adaeri Bending height:1200 mm Machine data Length:4000 mm Width:2600 mm Height:1400 mm Weight:9000 kg

Condition: new, functionality: fully functional, Year of construction: 2025, Tube bending machine, CNC bending machine, tube bender, tube bending system, tube processing, tube technology, right-left bending, 3D tube bending, servo-electric, multi-axis bending machine, mandrel bending machine Capacity: -Round tubing mild steel S235 22 x 2,0 mm Ø -Round tubing stainless steel 1.4571 22 x 1,5 mm Ø -Max. moment of resitance 0,5 cm³ (S235) -Bending angle up to 180° + 10° spring back -Speed of bending axis max. 300°/sec. -Speed of front feed axis max. 1800 mm/sec. -Speed of rotation axis max. 600°/sec. -Repetition tolerance bending +/- 0,05° -Repetition tolerance length +/- 0,05 mm -Repetition tolerance rotation +/- 0,05° -Radius max. 66 mm -Bending height 1150 mm -Boosting force length positioning 2,5 kN -Power bending axis servo-electric -Automatic positioning rotation/ length servo-electric -All other axes servo-electric (e.g. clamping, mandrel forwards/ backwards, etc.) -Positioning of the bending heads servo-electric -Positioning of the pressure die (radial) servo-electric -Pressure die movement (axial) servo-electric -Material clamping (chuck) pneumatic Machine equipment-/basic accessories: -Bending head for bending right-hand and left-hand with one off set bend device -Bending head can be positioned horizontal and vertical, including rotation axis for change of bending direction (right- or left-hand) -Positioning of bending head via combined diagonal and rotation axis, this allows bending right- and left-hand in one operation -Bending direction free programmable, changing right-/left-hand for one tube geometry -Each bending head can be equipped with minimum two tool sets, e.g. with different bending radii or form-clamps, max. changing height for standard machine is 50 mm Cedpfxowvqgts Adaori -Max. difference of bending radii for each bending level 1,5xD -With hollow shaft for using tooling for small radii -Minimum clamping length on the tube end, because of wide opening pressure die which allows the off set bend device to move directly behind the bending tool -Chuck for use of segment collets Depending on the contour of the clamping segments, already formed tube ends can be clamped -Material clamping in the VWE pneumatic -Footswitch to open or close the collet in the offset bend device, for easy loading and unloading -Following pressure die for bends up to 180° (for radii up to max. 2xD, for lager bending radii the pressure die can be repositioned to ensure a constant contact up to 180° bending angle) -For a correct positioning of the mandrel the machine is equipped with a mandrel support -Automatic, programmable mandrel withdrawal -Minimum quantity lubrication for automatic mandrel lubrication, adjustable lubricant quantity, can be used from inner tube Ø 13.5 mm -Central lubrication for automaticall lubrication of all moving parts in the necessary cycle -Air conditioning for the electrical carbinet -Starting of operation via manual switch on the control panel -In manual mode, all functions can be operated by keyboard and mouse The machine is built according to the latest safety regulations -In order to comply with the CE guidelines, a safety barrier is required in addition (DB-SA...) -Colour RAL 7047 grey, RAL 3020 red Control description: -Control via Simatic PC IPC BX-32A, Xeon W-11155MLE

Condition: new, Year of construction: 2023, mandrel bending machine ZB 55 H - mandrel length 2000 mm - pipe bender for tubes and profiles up to 54 mm - solid construction for heavy using standard equipment: - modern electromecanic movement - SPS control unit - up to 1000 different programs - electronic measurement of length and angle - manual stop system - hydraulic tube clamping - adjustable hydraulic pressure - three jaw chuck - total power 5,2 KW Crodpfx Adjd H Rhieaoi - bending speed 28 degrees per second - min. bending radius 50 mm, max. bending radius 150 mm - minimum tube diameter 15 mm - 400 Volt 50 Hz 3 ph. - weight 900 kg HS-Code: 8462 2998

Condition: new, Year of construction: 2025, machine/vehicle number: 1018, THE MANDREL BENDER WITH MANUEL CLAMPING: This mandrel bending machine with manual eccentric quick clamping for tube fixing enables rational bending. The compact drive unit with the detachable mandrel carrier offers advantages when used at the assembly site. Optimum bending accuracy is achieved by position detection directly on the bending axis. The bending angle is set easily and quickly via a convenient touchscreen control with menu-driven user interface. The comfort control allows two speeds as well as a parameterizable overbending function to compensate for material springback. The bending sequence is significantly shortened by automatic "free travel" at the end of the sheet. For more complex bending tasks, bending programs can be stored with a maximum angle sequence of 50 bends per geometry. An almost unlimited number of programs can be stored on the control or a USB stick, as well as 200 materials. The plug-in bending tools allow rapid conversion to other tube sizes. For difficult geometries, the bending direction of the machine can be changed to right or left bending as standard. The open bending unit allows, for example, the bending of railing frames with only one weld seam. The optional calculation software on the PC determines the cut length for the entire geometry as well as the travel distance, twisting angle and bending angle for each bend. The mandrel retraction is programmable and can be retracted automatically ahead of time when a bending angle is reached. POSSIBLE APPLICATIONS: - Plant engineering, e.g. chemical industry - hydraulic piping - prototyping - Pipeline construction TECHNICAL DATA: - Bending capacity Ø 6 to 50 mm - bending radius min/max: 10 mm/140 mm - Bending radii 2 x D Cjdpfx Adsnfvy Uoaori - multifunction machine control bending angle adjustment (0,1°) - mandrel beam lengths 1500/3000/4500/ 6000 mm (special version also longer) - Maximum 180º bending result - Weight 300-500 kg (depending on version) Optional accessories: - Automatic mandrel lubrication (minimum quantity) - Digital displacement measurement for length and twist (resolution 0.1 OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, "Bend speed: programmable for every bending anglevariably up to 1 rpm Control: 7“ and 4,3” touch-screen with oicons Csdpfxsuudg Io Adaeri Number of programs: unlimited by USB interface LAN or W-LAN connection (optional) Right/left bending (with special tool) possible Depending on machine type: Dimensions, weight, bending radius and bending capacity"

Condition: used, Year of construction: 1990, Technical details: tube diameter: 42 mm wall strength: 25 mm round bar steel: max. Ø 20 mm square material: Rohr 25 x 25 mm bending radius max.: innen max: Ø 20 und außen max: Ø 170 mm bending speed: keine Angaben °/s tube pipe draw up length: 3000 mm control: Software RC 7000 Codpou Ibvuofx Adaeri weight of the machine ca.: 2,8 t dimensions electric cabinet: 800 x 700 x 2000 mm dimension machine xH: 5,1 x 0,7 x 2,0 m Application: Machining of deformable tubes, rectangular tubes and round bars and square tubes. Description of the software RC7000, programming manual rectangular tube 42 x 20 x 2,5mm bending direction to the left Operation via control panel with monitor Accessories: -div. bending tools for tube Ø 25mm -12 div. collets -div. auxiliary and clamping devices *

Condition: new, functionality: fully functional, Year of construction: 2025, controller manufacturer: Self-developed brand, workpiece length (max.): 2,000 mm, workpiece height (max.): 160 mm, nominal power (apparent): 45 kVA, number of spindles: 14, machine/vehicle number: 2016, Product Features: The KaFe manual Panel Bender (Bending Center) is a next-generation, fully automatic multilateral bending center, offering high precision and efficiency. It represents a benchmark for automated production in the sheet metal manufacturing industry. It significantly reduces labor costs and boasts a bending speed three times that of CNC press brakes, reaching 0.5 seconds per cycle. Full servo control ensures product accuracy within 3 seconds. Product Function: Cjdpfxoxu Uhve Adaori The KaFe Manual Panel Bender (Bending Center) can bend sheet metal into various complex shapes without the need for molds. Equipped with a pure electric servo system, it replaces hydraulic drive and offers environmentally friendly, high-speed, high-precision, and maintenance-free features. This high-tech product was developed and manufactured to improve production efficiency, reduce labor intensity, and enhance corporate image in the sheet metal industry.

Condition: refurbished (used), functionality: limited functionality, Year of construction: 2003, operating hours: 24,000 h, pipe diameter (max.): 100 mm, pipe length (max.): 4,100 mm, bending angle (max.): 183 °, bending radius (max.): 300 mm, wall thickness: 8 mm, Transfluid DB 2090 DB CNC Mandrel Tube Bending Machine. Excellent High Quality Germany Machine, with fully refurbished main hydraulic pumps and main head fully reconditioned. Only requires new encoder to be fitted and this machine is ready to go. Features include. 100mm x 1.6mm Tube Maximum Capacity at 1.5D Anticipated Mandrel Withdrawal Fully automatic setup of clamps and follower Boosted Follower for tight radius thin wall tube bending. Long bed with 4000mm over mandrel. Comes with huge amount of tooling worth over AU$150k. Tooling Included: 101.6mm 152mm CLR 101.6mm 200mm CLR 76.2mm 114mm CLR 76.2mm 200mm CLR Credpfstrd T Tox Adaei 76.2mm 238mm CLR 63.5mm 96mm CLR 57.2mm 86mm CLR 50.8mm 76mm CLR 44.5mm 67mm CLR 40 x 40 120mm CLR 50 x 50 150mm CLR 60.3mm 150mm CLR 48.3mm 120mm CLR

Condition: new, Year of construction: 2025, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. Csdpfxsndn Age Adaeri The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 600-700 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, "Properties: Bending radii: R10 to R200 (min. R= 1.8xD) (depending on the wall thickness, the material and the pipe diameter) Max. Bending speed: 2 rpm and 3.2 rpm without inverter Operation: NC soft-touch control panel in 8 different languages and foot pedal Number of programs: 30 per 9 bends Control: NC1 Bending direction: counterclockwise Effective length (available in different lengths as required): 1,5 / 3 / 4 / 6 m Dimensions (W x H x D): 1000 x 1500 x 3600 mm (length for 3 m version) Weight: approx. 600 kg (with 3m mandrel) NOTE: The price quoted refers to a length of 1.5 m. Other lengths available on request! Premature mandrel retraction Positioning and rotation with mechanical stops and precise digital display Pneumatic four-jaw chuck Performance: Hard copper and aluminum : 60 x 4 mm Steel tube : 60 x 3 mm Stainless steel : 60 x 2 mm Scope of delivery: Cjdpfjuudrksx Adajri Machine Standard accessories (e.g. foot switch, operating instructions, 2 hex, 4 sets of chuck jaws, bending grease, 25 mm mandrel bar) Delivery without hydraulic oil"

Condition: used, Year of construction: 1993, Technical details: tube diameter: 80 mm Codeu Ibyyepfx Adaori tube diameter min.: 6 mm control for program: Gelma MM-1 tube pipe draw up length: 1800 mm weight of the machine ca.: 0,232 t dimension machine xH: 1,9 x 0,7 x 1,3 m Semi-automatic PIPE BENDING MACHINE Operating modes are manual but also semi-automatic Application: for multiple bending of pipes The swivel unit with bending preselection for 3 different bending angles in single and automatic mode. The machine is currently equipped with a stop bar for tube size Ø 10mm for 6 angle settings. The bending machine is movable/adjustable. Equipment/accessories: 6 cam rods/stop rods 6 control disks Bending tool for Ø 12mm *

Condition: new, Year of construction: 2025, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 800-900 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: Codpfx Aong Exajdaori - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site