Condition: reconditioned (used), Year of construction: 2014, operating hours: 5,612 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total height: 2,800 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), empty load weight: 12,000 kg, volume flow: 332 m³/h, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,612 hours, stand August 2025 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Csdpfx Afevtpq Holohf Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press was partially overhauled and tested in our workshop, see photos. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, pressing force: 60 t, Used HSM V-Press 1160 Plus vertical press from 2015. The device is regularly serviced by an authorized service center. The press is fully functional and in very good technical and technical condition. Codpsxyduvefx Aflehf Crushing force: 594 kN Voltage / required: 400 V / 50 Hz Width x height of the loading opening: 1195 x 650 mm Bale length x width x height: 1200 x 1100 x 1200 mm Width x height x height of the machine: 1780 x 1568 x 2985 mm Machine weight: 2403 kg Pressed material: foil, mixed paper, cardboard, cutting machine waste Freight costs depend on the weight, volume and above all on the distance, the following information is relevant for inquiries: Delivery address (postcode and name of the town), but further details require a telephone call, so we ask you to inquire about transport costs and other delivery modalities to contact us by phone. Our contact details can be found under the legal information of the seller. We sell and export worldwide, due to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-community invoices - excluding VAT. Opening hours Mon-Fri: 8 a.m.-4 p.m. sat .: closed

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, transport height: 2,300 mm, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Drive: 37 kW Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Transport weight: 27,000 kg Technical specifications conveyor belt: Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Chodpfx Afoxl Rqbolef Filling option: at floor level

Condition: like new (used), Year of construction: 2021, functionality: fully functional, machine/vehicle number: 20212531, The HiTec Steam Cooker, are versatile, custom-built cookers are designed to Steamcook & pasteurize, a wide range of production needs such as gyoza, dumplins etc. Engineered with food safety,EHEDGE, efficiency, and footprint in mind. Year of construction 2021 and not used much since that! Cedpfx Afjxl Tnpjlshf

Condition: good (used), Technical data: Briquetting press RUF RB 440 Press capacity when pressing wood: up to a maximum of 440 kg/hour Csdpfxot H D Ezs Aflehf Material moisture: maximum 15 % Motor power: approx. 30 kW Briquette size; rectangular: 150 x 60 mm Length: 40 - 110 mm Dimensions approx. 1680 x 1800 x 2000 mm Weight: 3000 kg

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Drive power: 31.5 kW Pressing force: 60 t Bale weight (depending on material): 350–600 kg Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Pressing/cycle time: 13/24 s Machine weight: 7000 kg Chsdpfov Amw Nsx Aflsf

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Chsdsxbgnhopfx Aflef Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 48 t, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total width: 2,583 mm, total height: 3,994 mm, total length: 6,661 mm, Equipment: documentation/manual, HSM VK 4812 P Year of production: 2015 Csdpfx Afoxx N Hzslehf Fully automatic baler. The device has service and maintenance work by an authorized HSM service with a branch in Germany. The baler comes complete with a ramp for ejection of finished bales and stands for binding wires. Pressing force: 480 kN Drive power: 18 kW Voltage / frequency: 400 V / 50 Hz Capacity at 50 kg/m³: 10.2 t/h Bale width x height x length: 1100 x 750 x 600 - 1200 mm Total length x width x height: 6661 x 3994 x 2583 Machine weight: 10.2 t Compressed material: foil, mixed paper, cardboard, die-cutter waste Bale tying: 4-fold with wire We also have other presses in stock. Transport costs depend on weight, volume and, above all, distance, the following information is important for inquiries: Delivery address (postal code and city name), but further details require telephone contact, so please inquire about transport costs and other delivery methods to contact us contact us by phone. Our contact details can be found in the seller's legal information. We sell and export worldwide, and thanks to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-Community invoices - without VAT. opening hours Mon-Fri: 8:00-16:00 Sat: closed

Condition: used, Year of construction: 2021, Chamber Press - Baler MACFAB BMF150 HT, used 🧰 Product Features • Manufacturer: MACFAB • Model: BMF150 AUTO HT • Condition: Used, see photos • Colour: Green • Year of manufacture: 2021 • Dimensions: approx. 1560 x 1030 x 2630 mm • Own weight: 786 kg • Pressing force: 80 kN • Cycle time: 40 seconds • Power: 2.2 kW (16A) • Voltage: 220 - 240 V (single phase) / 50/60 Hz • Noise level: 68 dB • Bale weight: 150 kg (depending on material) 💰 Price €3,700 net, excluding VAT Chsdsxwc Uiepfx Aflef • Quantity discount: on request • Shipping costs: Europe-wide on request • Delivery time: Available immediately • Inspection and collection: possible at any time by appointment Over 5,000 linear metres of pallet racking from various manufacturers permanently in stock (Subject to changes and errors in technical data, specifications and prices as well as prior sale! See our Terms and Conditions, all prices excl. VAT, ex stock.)

Condition: used, Year of construction: 2006, functionality: fully functional, Paper/Waste Baler JONGEJANS model: DBF145_00_h00004 Number of filters: 84 Needlefelt polyester Filter surface area: 145 m² Installed components: Briquette press CS3-12 Cleaning fans 1.5 kW Chsdpfxoxk N Dwo Afljf

Condition: refurbished (used), Year of construction: 1992, functionality: fully functional, machine/vehicle number: 305.537.1992, warranty duration: 12 months, Le Meccanica CLM630ST 630/150 die and rolls Force Feeder with a 0.9KW motor Currently undergoing full refurbishment - Seals &bearings included Colour - customers option Chedpsv Sq Rlsfx Aflsf Customer to arrange collection and freight

Condition: reconditioned (used), Year of construction: 2013, functionality: fully functional, Wet waste press press container Bergmann MPB405 SN/10 for skip loader 10cbm usable volume tested, serviced, fully functional Painting in desired RAL color possible Chsdpfovmwpwox Aflof We would be happy to make you an offer including delivery.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 13,209 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,050 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 700 mm, bale weight: 500 kg, oil tank capacity: 400 l, empty load weight: 8,500 kg, year of last overhaul: 2025, volume flow: 108 m³/h, Technical data baler: Manufacturer according to type plate BRAMIDAN (original manufacturer Presto GmbH & Co. KG) Type HC 50 (corresponds to the Presto HPK 50) Year of manufacture 2007 Operating hours 13,209 hours, as of March Number of bales pressed: 23,379 bales Pressing force 50 tonnes Specific pressing force 650 kN/m² Feed chute dimensions 1250 x 1050 mm (L x W) Chodpsw U Dt Nefx Aflef Filling volume 0.96 cm³ Theoretical cycle time 32 seconds Theoretical throughput capacity 108 m³/hour Bale dimensions 1100 x 700 mm (w x h) length variable Drive power 15 kW Power consumption, total in 50 A Tying 4-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm approx. 3.1 t/hour Bulk weight of 60 kg/cbm approx. 4.5 tonnes/hour Bulk weight of 100 kg/cbm approx. 7.2 tonnes/hour Bale weights with a bale length of approx. 1.2 m up to 500 kg, depending on material Hydraulic oil tank capacity 400 litres PLC control Siemens S7-200 Effective transport dimensions excluding baler 6780 x 1800 x 2100 mm (l x w x h) Transport weight of press 8.5 tonnes Condition of the baler: The press was used in a production facility exclusively for pressing cardboard and was regularly serviced. With only 13,209 operating hours, the machine has seen little use. The press was partially overhauled in our workshop and then tested. The following overhaul work was carried out: Machine cleaned Bale retainer made operational and lubricated Light barrier replaced Twisting unit completely dismantled, broken down into individual parts, all bearings replaced, all plastic glides replaced, lubricated, chain tension adjusted Knife and counter knife dismantled, sharpened, reassembled Knife gap readjusted General maintenance work carried out and lubricated Scope of delivery: 1 baler with wire roll boxes, without wire 1 set of machine documentation Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, pressing force: 70 t, bale weight: 600 kg, HSM HL 7009 Re/Li Horizontalballenpresse. Die Maschine befindet sich in sehr gutem Zustand und wird regelmäßig von einem autorisierten Servicecenter gewartet. Diese Ballenpresse ist für größere Entsorgungsprojekte im Einzelhandel sowie in kleinen und mittleren Zentrallagern konzipiert. Die Ballen des Modells HL 7009 haben einen Querschnitt von 1100 x 1100 mm und können bei einer Ballenlänge von 1200 mm bis zu 600 kg wiegen. Dies gewährleistet eine optimale Ausnutzung der Nutzlast des LKWs. Presskraft: 700 kN Spezifische Presskraft: 58 N/cm² Antriebsleistung: 10,5 kW Csdpsxx I Hyjfx Aflohf Spannung / Frequenz: 400 V / 50 Hz Leerlaufleistung (theor.): 42,97 m³/h Einfüllöffnung Breite x Länge: 890 x 1020 mm Ballen Breite x Höhe x Länge: 1100 x 1100 x 1200 mm Gesamtlänge x Breite x Höhe: 5366 x 2525 x 2559 mm Ballengewicht: 600 kg

Condition: used, Chamber Press – Baler ORWAK Compactor 3150, used 🧰 Product Features • Manufacturer: ORWAK • Model: Compactor 3150 • Condition: Used unit, see photos • Color: Green • Year of manufacture: 2024 • Dimensions: approx. 1366 x 1001 x 2546 mm • Net weight: 720 kg • Pressing force: 50 - 80 kN • Cycle time: 40 seconds • Power: 1.1 kW (10A) Cjdpexvzthofx Aflshf • Voltage: 230 V (single phase) / 50/60 Hz • Noise level: 62 dB • Bale weight: Plastic up to 190 kg, Cardboard up to 150 kg 💰 Price €3,900 net excl. VAT • Quantity discount: on request • Shipping costs: Europe-wide on request • Delivery time: Available immediately • Inspection and collection: possible at any time by appointment Constantly over 5,000 running meters of pallet racking from various manufacturers in stock (Technical data, details, and prices subject to change and errors excepted. Intermediate sale reserved! See our terms and conditions. All prices excl. VAT ex warehouse.)

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Chedpfxevq Rtko Afljf Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: ready for operation (used), Pressing force 60s tons Dixi 60s baler, year 2006-2012 costs 4,000 EUR Chodpfora Nqhex Afljf YEAR 2018-2020 costs 5,500 EUR Bale dimensions: 120 x 80 x 110 cm Press dimensions: 1900 x 1400 x 2200 mm (height) Press weight approx. 2,430 kg Bale weight up to 500 kg Oil heating Motor 7.5 kW Brand new exhibition unit costs 11,000 EUR

Condition: good (used), Year of construction: 2011, operating hours: 1,866 h, Manufacturer: Husmann Chodpfx Afjw Uz Hajlsf Typ: SPB 20 SEL-E Volume: 20m3 Build in: 2011 Backdoor: top hingend

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, pressing force: 80 t, bale weight: 600 kg, Equipment: documentation/manual, DIXI 80 SLS horizontal press Chedpjxx Iq Ejfx Aflsf Semi-automatic press system with 80 tons of pressure for economical volume reduction of residual materials (recyclable) in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulating mats and other compressible materials. Pressure force : 80 t Electrical connection : 400 V 50 Hz; 11 kW; D-32 A (option: K-32 A) Cycle – average approx. : 35 sec Length approx. : 4,320 mm (without lifting device and pallet) Width approx. : 1,830 mm Height approx. : 2,620 mm (with hopper) Loading opening (WxD) – housing : 1,040 x 1,110 mm Bale dimensions : 1,120 x 1,120 x 1,200 mm Bale weight approx. : 500 – 600 kg Tying 4 manual, wires with quick-release eyelets Machine weight approx. 8,000 kg (without bale)

Condition: used, Year of construction: 2005, Chamber press - baling press Austropressen APV 300, used 🧰 Product features • Manufacturer: Austropressen • Model: APV 300 • Condition: Used item, see photos • Color: turquoise • Year of manufacture: 2005 • Dimensions: approx. 1620 x 1260 x 2920 mm • Own weight: 1650 kg Cedsxvy N Uopfx Aflohf • Pressing force: 300 kN • Cycle time: 45 seconds • Power: 5.5 kW • Voltage: 400 V (12.5 A) • Bale weight: 300 - 400 kg 💰 Price: €7,200 net excl. VAT • Quantity discount: on request • Shipping: Europe-wide on request • Delivery time: Immediately available • Inspection and collection: possible at any time by appointment Constantly over 5,000 linear meters of pallet racking from various manufacturers in stock (Technical data, details, and prices subject to change and error, as well as prior sale! See our GTC, all prices excl. VAT ex stock.)

Condition: ready for operation (used), Year of construction: 2003, Technical data of baler 18S: Motor: 4kW Connection voltage: 400/50 V/Hz Press force: max. 180 kN Cycle time: 22 s Pressing time: 12 s Filling opening W x H: 107 x 62 cm Height w. Floor: 98 cm Ejected bale* W x H x D: approx. 110 x 70 x 70-80 cm Bale weight: 120 - 180 kg max. Dimensions W x D x H: 152 x 95 x 197 cm Weight 850kg The 2003-2007 vintage costs 3500 eur Cedpera Aghofx Aflehf Yearbook 2008-2009 costs 3800 eur The 2010-2013 vintage costs 4500 eur Yearbook 2016-2018 costs 5000 eur

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 60 t, input voltage: 400 V, bale weight: 550 kg, overall weight: 2,500 kg, Used HSM V-Press 1160 Plus vertical press from 2016. The device is regularly serviced by an authorized service center. The press is fully functional and in very good technical and technical condition. Crushing force: 594 kN Voltage / required: 400 V / 50 Hz Width x height of the loading opening: 1195 x 650 mm Bale length x width x height: 1200 x 1100 x 1200 mm Width x height x height of the machine: 1780 x 1568 x 2985 mm Machine weight: 2403 kg Pressed material: foil, mixed paper, cardboard, cutting machine waste Freight costs depend on the weight, volume and above all on the distance, the following information is relevant for inquiries: Delivery address (postcode and name of the town), but further details require a telephone call, so we ask you to inquire about transport costs and other delivery modalities to contact us by phone. Our contact details can be found under the legal information of the seller. Chodpoxw R Nhefx Aflof We sell and export worldwide, due to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-community invoices - excluding VAT. Opening hours Mon-Fri: 8 a.m.-4 p.m. sat .: closed

Condition: used, Year of construction: 2019, Chamber Press - Baling Press - Raw Material Press Bramidan X30 AD, used 🧰 Product Features • Manufacturer: Bramidan • Model: X30 AD • Condition: Used, see photos • Color: Orange • Year of manufacture: 2019 • Dimensions: approx. 1760 x 1255 x 2295 mm • Net weight: 1650 kg • Press force: 300 kN Chedpfxexvyn Ds Aflof • Cycle time: 25 seconds • Power: 4 kW • Voltage: 3 x 230 - 440 V / 50/60 Hz • Noise level: 59 - 60 dB • Bale weight: Plastic up to 425 kg, cardboard up to 350 kg 💰 Price € 8,900 net excl. VAT • Quantity discount: on request • Shipping costs: Europe-wide on request • Delivery time: Immediately available • Inspection and collection: possible at any time by prior arrangement Constantly over 5,000 linear meters of pallet racking from various manufacturers in stock (Subject to changes and errors in technical data, information and prices as well as prior sale! See our terms and conditions; all prices excl. VAT ex stock.)

Condition: excellent (used), Year of construction: 2014, pressing force: 60 t, bale weight: 450 kg, DIXI 60 SLD horizontal press baler 2014 year of production Press checked by service / new hydraulic cylinder installed. Semi-automatic 60 ton press system for economical volume reduction of residual (recyclable) materials in industry and retail: Cardboard Tetra Packs foils Foams PET bottles Insulating mats and other compressible materials. Csdpfx Aexw R Ecsflshf Machine dimensions L x H x W approx. mm: 4150 (5080) x 1725 x 2035 Filling opening W x H (standard) mm: 990 x 1110 Machine weight approx. kg: 5420 Pressing force max. kN: 60 t / 600 kN Ironing cycle (average value) approx. s: 47 Bale size W x H x L approx. mm: 800 x 1100 x 1200 Bale weight (depending on material) approx. kg: 370-410 Binding: manual Number of ties: 3, with wire Drive power: 7.5 kW; 400V/32A Freight costs depend on the weight, volume and above all on the distance, the following information is relevant for inquiries: Delivery address (postcode and name of the town), but further details require a telephone call, so we ask you to inquire about transport costs and other delivery modalities to contact us by phone. Our contact details can be found under the legal information of the seller. We sell and export worldwide, due to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-community invoices - excluding VAT. Opening hours Mon-Fri: 8 a.m.-4 p.m. sat .: closed

Condition: excellent (used), Year of construction: 1994, functionality: fully functional, pressing force: 12 t, bale length: 1,200 mm, bale width: 700 mm, bale height: 500 mm, bale weight: 450 kg, total length: 5,500 mm, Equipment: documentation/manual, The machine is in very good condition and regularly serviced. Manufactured in 1994, it was purchased from the original owner and is ready for use. The baler is started manually by a button or fully automatically using a photocell in the loading chute. Cutting blades mounted on the pressure plate cut the material and compress it in the baling channel. Once the desired length is reached (bale length adjustment is available), the bale is automatically tied after several baling cycles. The bale can be tied with wire, twine, or polypropylene tape. Automatic baling system with a 12-ton pressure for economical volume reduction of residual (recyclable) materials in industry and retail: Cardboard Tetra packs Cjdpfexw R D Esx Aflshf Films Foams PET bottles Insulation mats and other compressible materials. Baling pressure: 120 kN Bale size: 700 x 500 x 600 - 1200 mm Bale weight (depending on material): 280-450 kg Transport length: 5.5 m Weight: 3500 kg Drive power: 7.5 kW Transport costs depend on weight, volume, and, above all, distance. The following information is important for inquiries: Delivery address (postal code and city name), but further details require a phone call. Therefore, please inquire about transport costs and other delivery methods by calling us.