AUTOMATIC BORING (DRILLING) MACHINE - CN

BIESSE Techno FDT CN

Condition: excellent (used), ELECTRONIC (CNC control) machine, Numerical Control Type NC 500 - Software Tooling System N. 2 Through-feed motorized conveyoring belts - Feeding speed (m/min) 35 - 75 ca. Max. working width (mm) 3200. Min. working width (mm) 215 N. 2 Horizontal units/supports N° 2 Drilling heads for each horizontal unit (11 Spindles for each horizontal drilling head) N. 5 Bottom vertical units/supports Drilling heads/blocks for each bottom vertical unit (N°) 2 x HP 1,8 N. 2 Top vertical units/supports Drilling heads/block for each top vertical unit (N°) 2 x HP 1,8 N. 4 Vertical top pressure clamps - N. 2 Motorized endless screws to evacuate wastes/chips Quota (axes) digital display. Total installed power (Kw) 62,7 The CNC controls the movement (X axe) of the mobile horizontal unit The CNC controls the vertical movement (Hv) of the 2 horizontal units The CNC controls the movement (X axe) of all the vertical units Pgsdpeyyw S Rofx Agnjr The CNC controls the movement (Y1 and Y2 axes) of the boring heads The CNC controls the movement (Y axe) of the stops The CNC controls the movement (X axe) of the pressure clamps The CNC controls the movement (X axe) of the conveyor belts The CNC controls programming of the working cycles

Year of construction: 2022, operating hours: 400 h, condition: as good as new (ex-display), functionality: fully functional, !!!Demonstration machine with low operating hours!!! Model: Lepton 5100 Year of manufacture: 2022 Operating hours: approx. 400 hrs Location: D 84069 Schierling Availability: short notice Equipment: - Base machine Lepton 5100 with screen decks 1 and 2 Screen deck 1 mesh size: 36 mm Screen deck 2 mesh size: 24 mm - Pre-screen deck with large hopper and variable dosing roller - Volume measurement via load - Prepared for air separator - Compressor - LED lighting package - Radio remote control for all key settings - Diesel-electric drive 80 kW Pgodpfx Agert Uvzener - Axle levelling system - Tandem axle, road approval for 80 km/h - 19,000 kg total weight - Transport dimensions: 11.97 m total length, 3.98 m height, 2.53 m width, no special transport permit required Possible screening materials: Compost, green waste, biomass, root wood, waste wood, municipal waste, RDF, various recyclables (not suitable for construction rubble or excavated material) Miscellaneous: Very good used condition, fully operational

Condition: excellent (used), Automatic ELECTRONIC Drilling and Dowels inserting LINE, CNC controlled: VZ0250A) LOADING SYSTEM “RBO” Tornado C 1300 with motorized rollers table and conveyoring belts to in-feed the 1st multi-borer VZ0250B) THROUGH-FEED MULTI-BORER “BIESSE” Techno FDT with CNC - No. 2 through-feed motorised belts, feeding speed up to 75 m/min - No. 2 horizontal units (each with 2 drilling heads at 11 spindles each, HP 1.8 each), - No. 4 bottom vertical units (each with 2 turnable drilling heads at various spindles, HP 1.8 ea) - No. 3 top vertical units (each with 2 turnable drilling heads at various spindles, HP 1.8 each) - No. 3 top pressing devices - No. 2 endless screws to evacuate the wastes. With CNC NC 500 to control, manage and run the 2 machines of this line VZ0250C) THROUGH-FEED MULTI-BORER & DOWELS INSERTER “BIESSE” Techno SDT with CNC - No. 2 through-feed motorised belts, feeding speed up to 75 m/min - No. 2 horizontal units (each with 6 inserting nozzles, such as Glue injectors and dowel drivers) - No. 2 bottom units (each with 2 turnable drilling heads at various spindles, HP 1.8 each) - No. 2 Top pressing devices - No. 2 endless screws to evacuate the wastes. VZ0250D) BRUSHING-CLEANING MACHINE "PIZZIGALLI" Mod. GP 11 VZ0250E) UNLOADING “RBO” Tornado SC/FE 1300 with motorized rollers table and conveyoring Psdpjd Nviqsfx Agnsgr belts out-feed from 2nd multi borer (and dowels inserter)

Year of construction: 2000, condition: good (used), Barberan laminating line all inquiries should be directed to the number 790800714 Pedpfx Agoilqvronogr line in continuous operation maximum lamination width - 1300mm min. gr. 3mm max. thickness 40mm maximum length of elements 2800 mm minimum length approximately 600 mm smooth speed control from the brushing machine, maximum speed 20 m / min. the line includes - automatic loading of Tommassini (out of order) - brushing machine up and down - heating lamps in front of glue rollers up and down - PVAC glue applicator - top-down drying lamps - a line of steel calenders for pressing - in addition, the line has a purchased crowning machine for the upper surface (working) - can be laminated on one side with PP foils

Condition: good (used), Year of construction: 1994, 2-sided planing machine, top and bottom Constant table (always the same feed height) Max. planing width: 600 mm Podpohuthyefx Agnsgr Max. planing height: 280 mm Planer shafts with strip knives Ready for immediate use.

Condition: used, functionality: fully functional, Year of construction: 2017, operating hours: 2,560 h, load capacity: 1,600 kg, lifting height: 4,950 mm, free lift: 1,500 mm, fuel type: electric, mast type: triplex, construction height: 2,150 mm, fork length: 1,200 mm, empty load weight: 3,400 kg, total length: 2,114 mm, drive type: Elektro, construction width: 1,100 mm, Electric 4-wheel forklift Load centre: 500 Mast type: Triplex Speed class: 20 Pgjdpew U E Uusfx Agnjr Condition: Ready for use and fully functional Technical condition: normal Front tyre type: Non Marking Front tyre condition: 60 - 80% Rear tyre type: Non Marking Rear tyre condition: 60 - 80% Battery voltage: 48V Battery capacity: 625Ah Battery type: PzS Sideshift, 3rd valve, rear work light, front work light,

Condition: used, Year of construction: 2016, Angular panel saw with automatic pre-loading and twin pusher system for optimised cutting Pgjdpfx Aouc Idxognor Osi Plus Numerical Control Os Labelling labelling machine with on-board graphic labelling with part drawings Label printing management software Optiplanning Cutting Optimizer Cutting length mm 4500 Cutting width mm 2200 Blade projection 95 mm Motorized rollers for lateral loading on lifting table 4500 x 2200 mm. The translation speed is 10.8 m\min (50hz) - 13.1 m\min (60hz) Automatic recognition of the lost panel (martyr panel) based on the thickness specified in the machine data Low battery stop Automatic side loading buffer. Includes: perimeter nets, double photocell, push-button panel, predisposition electric for the two motorized pre-rollers and the amplification of 4 rollers in place of the fork passages in the pre- intermediate roller conveyor Pre-loading side roller conveyor dim 3800 x 2200 mm with motorized rollers (height from the ground 325 mm) Inertial conveyor for conveying longitudinal trimmings for angular systems 4500 mm (total length 7295 mm) 3000 mm extension to the inertial conveyor to also convey transverse trimmings Long chute for manual conveying of cross-cut trimmings to the centralized inertial conveyor 2050 x 850 mm air curtain discharge table with wheels at the front Air generator up to 6 floors with air curtain MULTIPUSHER 2.4 system with automatic lubrication Additional mobile lateral aligner on the transverse plane. The presence of this device allows to reduce from 1830 to 1220 mm is the minimum length of the panels that must be sent for cross-sectioning. Automatic blade shaft bending detection device for angular systems (longitudinal and transversal) consisting of a sensor that detects the deflection directly on the blade shaft and a device that detects the revolutions blade directly on the spindle. Remote cycle start button panel Automatic panel loading via rear lifting table Automatic double aligner with pneumatic cylinders Additional movable lateral aligner on the transverse plane Main blade, max diameter mm, KW 15 Scoring blade, max diameter mm, KW 2.2 Blade carriage speed 1-140 m/min. – BRUSHLESS motors Longitudinal pusher carriage speed 90 m/min. Cross pusher carriage speed 135 m/min. Double pusher carriage with 6 grippers on the longitudinal carriage + 10 grippers on the transverse carriage (8 fixed grippers + 2 on the multi-push system) Cutting system for thin panels

Condition: reconditioned (used), Number of spindles 5 St. Working width 230 mm Working height 120 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 5-30 m/min. Control Memory-Funktion Weinig Powermat 400 with HSK/Powerlock, axial/radial CNC controlled ----- This machine is currently being refurbished at our facility! Pictures taken before dismantling and currently during the processing phase! Brief Summary: ----- - 5 spindles with 8,000 rpm - 4 x HSK/Powerlock - Axially and radial CNC adjustments of the spindles via control - CNC-controlled adjustment and positioning of the feed - Table tops with guide blades at spindles 2 and 3. - Includes Weinig/Neumann RF 15 return conveyor system Detailed Description: ----- Technical Data: Working width: 20-230 mm Working height: 8-120 mm 1st tool holder - bottom ----- Motor with brake: 5.5 kW Spindle diameter: 40 mm Speed: 6,000 rpm Tool swing diameter: 93 - 145 mm Axially travel: 5 mm Folding device MarathonCoatin for table insert in front of 1st lower Tool Holder 2nd Tool Holder - PowerLock - Right ----- Motor with brake: 7.5 kW Shared motor with left tool holder Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter 40 mm below table level: 93 - 200 mm Tool swing diameter 55 mm below table level: 93 - 180 mm Tool swing diameter for straight cutter heads max. 163 mm Max. tool diameter behind stop plane: 180 mm Max. groove depth: 35 mm Axially travel: 55 mm Spindle: CNC controlled axially Table tops with guide blades 3rd Tool Holder - PowerLock - Left ----- Motor with brake: Shared motor with the 2nd spindle Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter 40 mm below table level: 93 - 180 mm Table surface: 93 - 200 mm Tool swing diameter 55 mm below table surface: 93 - 180 mm Tool swing diameter for straight cutter heads max. 163 mm Max. groove depth: 35 mm Axially travel: 55 mm Spindle axially and radially CNC controlled Table tops with guide blades 4. Tool holder - PowerLock - top ----- Motor with brake: 7.5 kW Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter: 93 - 200 mm Tool swing diameter for straight cutter heads max.: 180 mm Max. groove depth: 35 mm Axially travel: 40 mm Split pressure shoe in front of upper tool holder, adjustable and pivoting away from the tool, spring-loaded. Pressure shoe in front of, and discharge after, the upper tool holder with electronic digital displays, integrated into memory functions CNC-controlled radial spindle 5. Tool holder - PowerLock - bottom ----- Motor with brake: 7.5 kW Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter: 93 - 200 mm Psdeyy A Iqspfx Agnsgr Max. throat depth: 15 mm Axially travel: 35 mm Feed system ----- Frequency-controlled feed, infinitely variable with brake: 4 kW, 5 - 30 m/min Infeed roller in front of the first lower tool, pneumatically controlled up/down. Durofer pointed tooth rollers (Weinig patent) wi...

Condition: used, Year of construction: 2022, Overview  The GAI filler was manufactured in 2022 by the Italian company GAI. This machine is used to fill sparkling wine into cylindrical bottles from 0,2L until 1,5L. It is equipped with a rinser (air or water) 16 nozzles, 24 electropneumatic filling valves and 3 capping turrets (3 capping heads on each turret). Each capping turret has its own cap feeding and alimentation system. Dedusting unit for the corks is installed. Integrated overpressure roof with prefilters and absolute filters. This machine is sold with an automatic CIP and 2 pallets of microfiltration Win&tech. The machine is still in production and can be visited. The condition of the machine is like new, as it has only 200 working hours. Technical details  - Working direction: left to right Pgodsv Aag Dopfx Agnjr - Capacity: - 0,187ml - 4500bph 4°C & 15°C - 0,375ml - 4500bph 4°C & 15°C - 0,750ml - 4000bph 4°C &  2900bph 15°C - 1500ml - 2000bph 4°C & 1500bph 15°C - Currently set up for: - Glass Bottles: - 0,187ml - 0,375ml - 0,750ml - 1500ml  - Caps/Corks - Cork (boucheuse liège) - Screw cap - Decorative Cap (Champagne style) - Incl. CIP and wine filtration

Year of construction: 2005, condition: good (used), machine/vehicle number: C9 15840, Profile brushing machine Tagliabue LB 2 Model: LB 2 Podpfx Aeg Rn Iaognegr TECHNICAL DATA: Year of manufacture: 2005 Tagliabue edge sander with 4 oscillanting sanding units. Two vertical rollers and 2 inner transversal rollers, for transversal brushing.