Milling machine

CME MB 3000 FLEX

Condition: used, Year of construction: 2001, x-travel 2050 mm y-travel 1100 mm Lredpsrw Dknofx Ahzjg z-travel 800 mm Control Fanuc 18iM Super Cap II turning speeds 60-6000 U/min tool magazin: 60 tool taper BT50 total power requirement 26 kW weight of the machine ca. 23,6 t required space 6,3 x 3,3 x 3,8 m

Year of construction: 1984, condition: ready for operation (used), Rafamet UBB 112/2 Wheel Tread Diameter Minimum 700 mm Wheel Tread Diameter Maximum 1120 mm Clamping length 540 - 1050 mm Wheelset Axle Length Minimum 1640 mm Wheelset Axle Length Maximum 2800 mm Ledpfx Ahohvml Iszjrg Maximum Tire Width 150 mm Maximum Wheelset Weight 4000 kg Saddle Set Up Motion Speed 2000 mm/min Saddle Feed Maximum 2000 mm/min Main Drive Motor Power 80 kW Weight aprox 40000 kg

Condition: new, Year of construction: 2024, 600 kg load capacity Welding turntable height adjustable with through hole 100 mm Plate diameter 700mm Horizontal height min. 0.65m, max. 1.25m Height tilted min. 0.45m, max. 0.95m Speed from 0.01 - 1.3 rpm Tilt up to 135° Lredpfx Asg Tdpgehzjg Hand and foot remote control with speed display very robust

Condition: excellent (used), Year of construction: 2005, travel distance X-axis: 600 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, rapid traverse X-axis: 35,000 m/min, rapid traverse Y-axis: 35,000 m/min, rapid traverse Z-axis: 35,000 m/min, workpiece weight (max.): 200 kg, total length: 500 mm, total width: 400 mm, table load: 200 kg, rotary table diameter: 280 mm, Coolant system Filtration tank HR 410 Handwheel iTNC530 controller 1e owner machine X - Travel: 600mm Y - Travel: 450mm Z - Travel: 400mm A - Axis: 110° B - Axis: 360° Table Length: 500mm Table Width: 400mm Table load: 200 Table Ø: 280mm Feed rate X-Axis: 35000mm/min. Feed rate Y-Axis: 35000mm/min. Feed rate Z-Axis: 35000mm/min. Feed rate A-Axis: 10Degrees/min Feed rate B-Axis: 15Degrees/min Spindle Taper: 40ISO/Bt/Mk Power on spindle: 15kW Speeds / ranges: 18000Rpm ATC / revolver: 30 Coolant through spindle / Bar:20 Number of controlled axis: 5 Chip conveyor: Yes Coolantsystem: Yes Lodpfxjx R S Smj Ahzerg Length: 3500mm Width: 3500mm Height: 2800mm Weight: 6600kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: like new (used), Year of construction: 2017, operating hours: 59 h, functionality: fully functional, grinding length: 400 mm, grinding width: 200 mm, feed length X-axis: 510 mm, feed length Z-axis: 220 mm, feed rate X-axis: 20 m/min, grinding wheel diameter: 205 mm, distance table to spindle center: 357 mm, table load: 120 kg, type of input current: three-phase, grinding wheel width: 16 mm, spindle speed (max.): 3,600 rpm, spindle speed (min.): 1,000 rpm, overall weight: 2,100 kg, grinding spindle motor power: 2,200 W, grinding wheel speed: 3,600 rpm, input voltage: 400 V, Equipment: documentation/manual, TECHNICAL CHARACTERISTICS: Year of manufacturing: 2017 Colour touchscreen: Yes Maximum grinding lenght x width: 400 x 200 [mm] Stroke X axis (table movement): 510 [mm] Min. Stroke speed X axis: 100 [mm/min] Max. Stroke speed X axis: 20000 [mm/min] Z axis travel (transverse movement): 220 [mm] Min. distance spindle nose / table: 22.5 [mm] Max. distance spindle nose / table: 357.5 [mm] Max. load on table: 120 [Kg] Grinding wheel min. speed: 1000 [rpm] Grinding wheel max. speed: 3600 [rpm] Grinding spindle motor power: 2.2 [kW] Max. diameter grinding wheel: 205 [mm] Max. grinding wheel width: 16 [mm] Min. grinding wheel width: 6 [mm] Grinding wheel bore: 31.75 [mm] Number of running hours: 59 [h] Supply voltage: 400 [V] Total power required: 11 [kVA] Weight : 2100 [Kg] INCLUDED EQUIPMENT: Ljdpow Hf Hiofx Ahzorg x1 150 [L] coolant tank FB1/R with papertape filtration unit FB1 x1 BRAILLON electro-permanent magnetic chuck type EPEFINE 2 x1 BRAILLON magnetic chuck remote control, microprocessor-based, type T10 x5 grinding wheel flanges x1 oil chiller x1 transformer x2 service keys x1 balancing shaft x1 set of axis-brackets for transport STANDARD CONVERSATIONAL PROGRAMMING MODE: Straight and angular dressing (standard) Surface grinding, multiple plunge grinding, and face grinding (standard) INCLUDED ISO PROFILING: Wheel profiling Contour machining of workpiece Full functionality for V-shape and freeform programming on the grinding wheel, and ISO contouring on the workpiece. Precise positioning integrated: +/- 1 [μm] Machine visible under power in our premises by appointment. Price on request, loading on truck included. Possibility of shipping Worldwide. The information on this page has been obtained by the best of our ability. Therefore, its accuracy can not be guaranteed. Similar machine to brands like Jones & Shipman, Jung, Favretto, Blohm, Studer. Also see cylindrical grinder, lathe, machining center, milling machine.

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: 3.04-00054, Equipment: type plate available, Used Bellaform extruder Type: BH45-30D Year of manufacture: 2013 With screw dimensions 45 mm - 30 l/d, screw speed approx. 160 rpm With 30 kW water-cooled servo motor, with gearbox Cylinder with 4 heating/cooling zones and water bushing in the feed area Material hopper plus a COLORTRONIC dosing screw for masterbatch Lsdpfxeuxa Abo Ahzerg A melt pressure sensor Control cabinet integrated into the machine frame, with factory-new PLC and With new touch panel for simple and intuitive operation This extruder has been functionally tested! Dimensions: approx. 195 x 70 x 200 cm (L x W x H with hopper)

Year of construction: 2024, condition: new, functionality: fully functional, The universal laser marking system LAS 28 XL from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fibre laser, you can mark almost all materials such as steel, hard metal, aluminium and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fibre laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realised with just a few clicks and without extensive programming knowledge. The software automatically counts up serial and article numbers after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. Bk3ky883 Lsdpeqfcvisfx Ahzjrg The standard equipment includes a laptop incl. holder with Windows operating system and laser software. Optionally, the laser model LAS 28 XL can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realised. Made in Germany Fiber laser 30W, 20 W or 50 Watt - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - marking software EZCAD in German / English - signal light for indication of operating status - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - optional: outrigger for large components (one-sided, both-sided) - pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - max. component height approx. 300mm - electrically adjustable Z-axis - Laptop incl. holder with Windows operating system - frame made of aluminum profile - air cooled - Door width approx. 700mm / door height(pass-through): approx. 400mm - Connection 230V - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) - Weight: approx. 100 Kg

Year of construction: 2024, condition: used, Grinding wheel holder:: HSK 50 E Diamond grinding wheel diameter: 50 - 250 mm max. width of grinding wheel: 70 mm Grinding wheel bore diameter: 20 mm Speed of the diamond / CBN disc spindle: infinitely variable 100 - 1000 rpm., Radius of the grinding wheel: 0-30 mm Dimensions of the dressing wheel: 180 x 25 x 31.75mm, Speed of rotation of the dressing wheel: 200 - 2000 rpm., Oscillation stroke of the dressing wheel: 0-70 mm Connected load of the motor of the dressing wheel: 2,2 kW Weight approx: 1400 kg Dimensions L x W x H: 1850x2300x2100mm, Description: Suitable for dressing and profiling diamond and CBN grinding wheels. ccesories: Total enclosure. Motor Upgrade (stronger motors for the wheel being dressed and the dressing wheel), Wheel motor strengthened to 4 kW, Dressing wheel motor strengthened to 2,2 kW, 2 Machine lights 12 V, Optical linear scale with digital display counter (0,001 mm) X, Z Axes, 2/3” TV Camera with 15” LCD monitor (microscope with zoom 15‐120X included), High performance swivelling angle reader (0,05°), Lsdpslfil Ssfx Ahzerg Diamond / CBN wheel spindle speed stepless adjustable 100 - 1000 rpm, Turning speed of dressing wheel stepless adjustable 200 - 2000 rpm, Stepless oscillation speed, Automatic central lubrication, SIC Wheel dresser manual,

Year of construction: 1990, condition: good (used), CNC-4th axis NIKKEN type: CNC-200 year 1990 Ledjgabu Ujpfx Ahzorg with counterholder and base plate.

Condition: used, Year of construction: 2015, x-travel 1.200 mm y-travel 600 mm z-travel 675 mm Control C 620 HSCI FS table-size 1.220 x 620 mm 40 fach Distance between table and spindle 735 mm turning speeds 10.000 U/min Lrsdpfx Ahjx Ak Hdjzjg spindle drive 18 kW Internal cooling system 30 bar -Electronic steering wheel. -LINEAR RULES. -Laser probe measuring tools. -Preparation for piece measuring probes. PROBE NOT INCLUDED.