Band saw

FMB Phoenix+G

Condition: new, Year of construction: 2026, CORMAK HBS275 band saw, equipped with a hydraulic cylinder, a cooling system and an arm swivelling up to 60º, together with blades from renowned German company Röntgen, is used commonly in ironworking, where precision, quality and cutting speed are essential. Horizontal band saw with a swivelling arm for cutting metals, allows for cutting in plane perpendicular to the axis of material cut and at any angle from 0 to 60º. Material for cutting can be fed manually or with any mechanical feeding device, with automatic tool feed. Band guides are equipped with dedicated carbide plates and bearings. This has a huge impact on band guiding, its durability, cut straightness, cutting accuracy and quality. Carbide guiding drastically reduces the wear of the machine and blades. Machine's arm made of uniform cast iron as well as a 27 mm wide cutting band are capable of low and high quantity cutting of profiles and other materials. The vice is located in an adjustable bed, equipped with a quick clamp. Blade guides have cemented carbide plates and roller bearings. Its these cemented carbide guides that provide cut precision and straightness. The arm, positioned at an angle of 25º, thus increasing blade durability. To the bottom of the arm a brush wire is attached, ensuring clean and functional brush. Machine's drive is transmitted through a worm drive. A 3-phase motor with 2 cutting speeds and motor thermal protection. This cutting machine also has a strain gauge - a band tension sensor and an automatic switch-off in case the cutting band breaks. Upper part of the base constitutes a tank for flood coolant draining and chips produced during cutting. A cast iron workbench is attached to the base, with a swivel arm and control panel on separate arm. The main cutting move in the cutting process is moving the cutting band and the arm lowering feed. The arm lowering speed (the cutting speed) is adjusted with the hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds to choose from: 37.5 and 75 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Total power 1.5 kW Nodpfx Aheudi Unozoct Power supply 400V 50Hz Arm lowering control hydraulic cylinder Band dimensions 2455 x 27 x 0.9 mm Band speed 37.5/75 m/min Vice base height 900 mm Weight 215 kg Angle 0º ø220 260 x 140 200 x 200 45º R ø160 160 x 140 160 x 160 60º R ø100 120 x 100 100 x 100

Year of construction: 1985, condition: reconditioned (used), Technical Details : Wire Dimeter range- 4-12mm Gscxckebw Run out table - 4m Speed -80' m/min. Reconstruction- 2022 Ncsdjh In Thspfx Ahzot

Condition: new, Year of construction: 2026, The CORMAK HBS260 band saw for cutting pipes, profiles and bars is widely used in all locksmith workshops where precision, quality and cutting speed are important. The model is equipped with a 0-60° swiveling arm. The frame design ensures accurate and quiet operation. It has a removable filing tray for easy cleaning! Machine characteristics A horizontal metal band cutter with a swiveling arm allows cutting in a plane perpendicular to the axis of the material being cut and at any angle ranging from 0 to 60°. The material to be cut can be fed manually or with any mechanical device, and the tool feed is automatic. The tape guides are equipped with special carbide plates and bearings. This has a huge impact on the belt guidance, its life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and saw blade. The machine is equipped with an efficient cooling pump with a closed coolant circuit. The cutter's arm made of uniform cast iron together with the 27 mm wide cutting band used in this cutter allows it to fully perform multi-series cuts of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The saw blade guides are equipped with hard metal plates - sintered carbides and a rolling bearing system. It is the CENTRED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The shape of the upper part of the base constitutes a bathtub for draining coolant and catching chips generated while cutting the material. A cast iron work table with a swivel arm and a control panel on a separate arm is attached to the base. In the cutting process, the main cutting movement is the movement of the cutting band and the falling feed of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic actuator. The feed speed is regulated on the cutter's control panel. We can choose from two cutting band speeds: 35 and 70 m/min. In the lower position of the arm (after cutting the material), the cutting belt drive is turned off automatically. Safety is ensured by the cutting band covers and micro switches that stop the engine after the cutting cycle is completed or any of the covers are opened. Additional protection consists in automatic shutdown of the cutter in the event of the cutting band breaking. Cutting band size [mm] 2520 x 27 x 0.9 Tape tension mechanical (manual) Belt speeds [m/min] 35, 70 Adjustable arm drop stepless - hydraulic actuator Vice base height [mm] 860 Saw wheel diameter [mm] 300 Saw frame tilt [°] 0-60 Power supply 3 phases 400V Main engine power [kW] 1.1/1.5 Cooling pump motor power [kW] 0.05 Dimensions with base [cm] 150x80x140 Weight [kg] gross/net - 210 / 180 kg Additionally 2 M42 saw blades 5L Emulsol Ncedpfoudi Uzex Ahzst ZW580 magnetic chip collector

Condition: used, wire diameter - max. 10 mm wire diameter - min. 3 mm wire length 8 m total power requirement 7,5 kW weight of the machine ca. 1,1 t dimensions of the machine ca. LxBxH 2,53 x 0,75 x 1,1 m Nedpfxjwu Hg Hs Ahzect

Condition: new, cutting diameter 220 mm saw band length 2450 mm cutting width 250 mm cutting speed 40 / 80 m/min dimensions of saw-band 2450 x 27 x 0,9 mm 100 mm 90 mm 90 x 90 mm 160 mm 160 x 110 mm 250 x 190 mm total power requirement 0,75 / 1,1 kW Nsdslb I A Sjpfx Ahzsct table height 925 mm weight of the machine ca. 218 kg dimensions of the machine ca. 1300 x 700 x 1530 mm

Condition: used, Year of construction: 1972, Technical details: wire diameter - max.: 12 mm wire diameter - min.: 2,0 mm control for program: Process Controler Total power requirement: 18,5 kW Weight approx.: 10,5 t dimension machine xH: 2,6 x 1,8 x 2,7 m dimensions LxWxH: Schmiermittelanlage: 0,6 x 0,4 x 0,8 m dimensions electric cabinet LxWxH: 0,5 x 1,2 x 2,1 m dimensions of coil: 2,6 x 1,8 x 2,7 m WRAIGHTING AND CUTTING MACHINE from the manufacturer Wafios-Hack Also called spring coiling machine, for the production of right and left hand tension / compression springs. Feed length 17400 mm Spring Ø 120 mm Output range: Yield 1 - 70 pieces/min. Spring Ø 25 - Ø 200 mm Wire thicknesses round steel Ø 5.0 - 140 mm and square steel 5.0 - 12.5 mm Feed speed - spring length max. 42,000 mm and wire feed F1= 40 m/min. + F2= 28 m/min. + F3=20 m/min. currently mounted on the machine: 6 feed rollers for wire intake Ø 4 mm to produce the end product: tension spring wire Ø 4 mm, outer Ø 34 mm and length at 135 mm Operation via control panel, Process Controler BRANKAMP Ncjdpfsu Ic Hnsx Ahzst Equipment: Lubricant system Wire reel reel Switch cabinet cooler reel Optional accessories and/or spare parts see photo i.D. *

Condition: good (used), Year of construction: 2010, cutting diameter 220 mm saw band length 2480 mm table height ca. 910 mm capacity 90 degrees: flat 245 x 115 mm capacity 90 degrees: square 195 x 195 mm capacity 45 degrees: round 150 mm capacity 45 degrees: square 140 x 140 mm capacity 60 degrees: round 85.0 mm capacity 60 degrees: square 85 x 85 mm turning speed range: 45 + 90 m/min dimensions of saw-band 2480 x 27 x 0.9 mm clamping width max. 270 mm total power requirement 0.75 + 1.1 kW weight of the machine ca. 200 kg dimensions of the machine ca. 1430 x 720 x 1700 mm New price in 2010 .. 2.400 Euro Special price on request Equipment: - For cutting profiles, pipes, solid materials made of iron Nsdpfsyf N D Uex Ahzect - and non-ferrous materials - The saw arm can be tilted up to 60° for mitre cuts - Infinitely variable lowering via hydraulic lowering cylinder - Torsion-free, heavily dimensioned cast iron saw arm - 2 saw blade speeds for optimum cutting results (400 V) - Automatic limit stop after material average - Robust cast iron vice with quick lock - Ball-bearing saw blade guide with quick adjustment for adapting to the workpiece width - workpiece width guarantees optimum work results

Condition: used, Year of construction: 1980, functionality: fully functional, machine/vehicle number: D08L/8081, Offer Number: D08L/8081 Machinetype: straightening and cutting machine Ncsdpfx Ajwi Svcjhzot Make: WMW Type: UDARA10 Constr. year: 1980 diameter range: 3-10 mm cutting length: 2000 mm speed - meters/min: 22-71 Location: In our warehouse

Condition: used, Year of construction: 2016, Machine data can be found in the pictures Nsdpfx Aev U Ea Tehzsct

Condition: excellent (used), Bridge crane, indoor crane, disc brake, crane brake, disc, drum and storm brakes, overhead crane brake, brake ring, conical brake disc Ncsdpfsxc Eupjx Ahzet -Manufacturer: Demag, brake ring conical brake disc unused -Type: 628 626 44 RIW -Dimensions: see photos -Dimensions: Ø 310 x 40 mm -Weight: 0.9 kg