HOMAG HSK AGGREGATE TRIMMING MACHINE

HOMAG

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Hfsdpsyqybuefx Abved Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: as good as new (ex-display), ►►► FRONIUS TPS 3200 SET OFFER ✅ Scope of delivery: ➤ Fronius TPS 3200 Power Source (320A TRANS PULS SYNERGIC) ➤ Fronius FK 4000 FC Cooling Unit – Standard features include Flow Control, Thermocontrol, and coolant filter. The cooling unit shuts off if the water cooling fails or gets too hot, to protect the torch package. These functions cost approximately €400 extra from Fronius. ➤ Fronius VR 7000 Wire Feed Case – Compact and practical – in our experience, the most useful wire feed case – the wire is securely stored in the closed case. ➤ Fronius Intermediate Hose Package, long version – each machine is supplied with a 5-meter-long connection hose between the power source and the wire feed case for greater flexibility and improved handling. Take the wire feed case off the machine to access hard-to-reach areas! The connecting hose is neatly stored on a hook on the side of the machine. (Hooks are produced by us) ➤ Fronius Large Trolley – Probably the best trolley with a gas bottle holder on the market. ➤ Binzel Torch Package – With up/down amperage control on the torch. ➤ Ground cable 3-4m ➤ New Messer pressure regulator ➤ New basket reel adapter for large wire spools With this machine, almost all materials can be welded, including aluminum, steel, and stainless steel (V2A). It features pulse wire programs and is also suitable for MIG brazing (CuSi), commonly used in the sheet metal industry. Additional options are available at extra charge For example: Fronius Aw4000/Aw5000 Job Master Torch Package (with display on torch) + EUR 550.00 ----- Hjdpfx Abowbil Ssvefd IMMEDIATELY AVAILABLE PROPER INVOICE Inspection is possible in Austria, Vienna 1230! ✔ Insured shipping on a pallet is no problem! ✔ We are also available via WhatsApp and Viber. ✅Questions✅Questions✅Questions✅Questions: ✅Questions✅Questions✅Questions✅ ►►► What is the condition of the equipment? For clarification: we purchase nearly new used equipment, disassemble and thoroughly inspect everything, replace wear parts as necessary, and only after a successful test weld do we release the equipment for sale. "All" machines are clean with no burn marks on the displays and without numerous burn holes or dents! With us, you buy an item that is ⭐in excellent condition and doesn’t look worn out! ►►► Do we receive an invoice when purchasing from you? Yes, you will receive a proper invoice from us. If you have a valid VAT ID and meet the requirements for intra-community delivery within the EU, we can issue a net invoice. ►►► What payment options are available? Prepayment or cash on personal collection. ►►► Why buy from us? We are experts in this series of Fronius welding machines and always have 60-80 units in stock – exclusively Fronius, no other brands! We know these machines inside out and do not sell anything we don’t have expertise in.

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Hedpfsyqx U Hex Abvofd Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, Specification: Cutting length: 4300mm Cutting Width: 4300mm Saw Blade Projection: 80mm Control Screen on Right Hand Side Machine Table fully air cushioned Program fence Speed forward 25m/min Program fence speed backward 90m/min Standard Clamps: 225, 325, 475, 775, 1075, 1825, 3425mm Power Concept – This allows several strips of different cross cutting lengths to be cut together with a performance increase of up to 40% Pressure beam height control Saw carriage speed 130m/min Main saw motor 11kw with pneumatic lift Scoring saw unit 1.5kw with pneumatic lift Electronic scoring saw adjustment from the control screen 4No air cushion tables 2160 x 650mm Label printer 400V 50Hz Control Touch touch screen monitor Hfodpeyuw Umefx Abvsd Data Transfer via network + USB port CE Eco Plus technologies save up to 20% on energy consumption

Year of construction: 2022, condition: new, ZIM T1200 machine can produce pipes 300mm – 1200mm diameter and 500mm – 2500mm height by single, double and triple pressing. 150mm and 200mm pipes also can be produced for special demands. Machines can be designed semi or full automatic according to requirements. We use SIEMENS brand PLC microprocessors on automatic machines. Hfjdpfjibbiksx Abvod There exists motrar bunker and motrar filling systems on machines. Produced materials can be carried to drying area with carriage carts or forklifts. Production is done on production pallets, Materials up to 800mm diameter are carried to drying area with carriage carts, pipes bigger than 800 mm diameter can be carried with forklift. For fast production, pipes bigger than 300mm diameter also can carried to drying area with forklift. Machine makes production by hydraulic press and vibration. Vibration system of the machine is special design of ZIM Engineers. Vibration system which have oil cooling system and special oil unit. This system can be controlled electronically. Special designed strong chassi of the machine enables long live producing without errors.

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 20 Panels thickness (min/max) mm 8 / 60 NEW (in 2024) Numerical Control EDGETEQ MOD - Power Touch (WoodCommander) Adjustable Feeding speed up to 25 m/min In-feeding system EZ 14 Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) 2 x Kw 3 Glueing Unit (P.U.R. Glue + Quick Melt system) Band Pressure zone, adjustable by N.C. Edge coils supporting unit (with No. 2 reels) Snipping (end-cutting) unit HL 84 (2 x Kw 0,5 ca.) Pneumatic swivelling and adjustment Rough Trimming unit BF 20 (2 x Kw 1,5 ca.) Multi Function Unit (Profile contour Trimming) FK 11 (2 x Kw 0,4 ca.) Profile edge scraping unit Finish processing unit (Glue scraper + Buffing unit) FA 11 Hjdpfxoyt Izbe Abvefd Panels Return System "LIGMATECH" Mod. ZHR 541/L/095 (with Portal bridge and 360° rotating vacuum head)

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, power: 19 kW (25.83 HP), travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,730 mm, number of spindles: 20, number of tool stations in tool turret 1: 18, TECHNICAL DETAILS Working area X-axis: 4,175 mm Working area Y-axis: 1,730 mm Number of suction traverses: 8 Tool magazine positions: 18 Spindles Number of spindles for vertical drilling: 17 Number of spindles for horizontal drilling (X-direction): 2 Number of spindles for horizontal drilling (Y-direction): 1 Total number of spindles: 20 Milling unit Number of controlled axes: 4 Hfjdoyttf Sopfx Abvod Motor power: 18.5 kW Automatic tool changer Liquid-cooled MACHINE DETAILS Total installed power: 19 kW Control model: PC85 EQUIPMENT CE marking Front safety cover Note: Cones, milling cutters, and aggregates are not included in the scope of delivery. Safety fences are supplied based on availability (left side only). The machine is sold and delivered in its actual and legal condition (‘as seen and approved’), based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer is entitled to inspect the goods prior to collection, and assumes responsibility for installation, safety, and use of the machine at the destination. External reference: 6906

Year of construction: 2005, condition: good (used), machine/vehicle number: C9 15840, Profile brushing machine Tagliabue LB 2 Model: LB 2 TECHNICAL DATA: Year of manufacture: 2005 Tagliabue edge sander with 4 oscillanting sanding units. Hjdpfx Abog Rn Iaovjfd Two vertical rollers and 2 inner transversal rollers, for transversal brushing.

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,550 mm, workpiece height (max.): 40 mm, number of spindles: 30, travel speed (max.): 80,000 mm/min, TECHNICAL DETAILS Travel range X-axis: 4,175 mm Travel range Y-axis: 1,550 mm Travel speed X-axis: 80 m/min Travel speed Y-axis: 80 m/min Travel speed Z-axis: 30 m/min Maximum workpiece height: 40 mm Number of suction traverse beams: 8 Spindles Number of spindles for vertical drilling: 20 Number of spindles for horizontal drilling in X-direction: 10 Total number of spindles: 30 Milling unit Number of controlled axes: 4 + Flex5 Motor power: 15 kW Automatic tool changer Liquid-cooled Saw unit Tool magazine 1 Number of slots: 18 Tool magazine 2 Number of slots: 10 EQUIPMENT NC positioning of suction units Vacuum pump Hfedpfx Aeyttcwsbvsd PowerControl P85 control system WoodWop 5.0 machine programming software Note: Cones and milling cutters are not included in the scope of delivery. The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and is responsible for installation, securing, and usage of the machine at the destination. External reference: 7350

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Mill Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Hfedpfx Aoytr Hbebvsd Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: new, Year of construction: 2021, Operating Area: 3048*1524mm Machine overall dimensions: 4960×2280×2200mm Laser Output Power: IPG 3000w/2000w/1500w X/Y-axis positioning accuracy: ±0.05mm X/Y-axis repositioning accuracy: ±0.03mm Hsdpfx Abog D Nypovsfd X/Y-axis Max. linkage speed: 100m/min 1. A Compact Design with Complete Protection Small occupied space balances complete protection and higher safety. 2. Active Anti-collision Function Effectively reduce the damage rate of laser heads, help you save maintenance cost. 3. Cast Iron Bed Featuring good shock absorption, Cast Iron Bed keeps its shape all the way with the optimal mechanical property.

Condition: ready for operation (used), Year of construction: 2006, Edgebander manufactured in 2006. This HOMAG Optimat KAL 330 features a flexible production layout for furniture parts, accommodating workpiece dimensions from 250 to 3000 mm in length and 120 to 1200 mm in width. It includes a single-sided edge banding machine capable of processing various edge materials up to 20 mm thickness. If you are looking to get high-quality edge processing capabilities, consider the HOMAG Optimat KAL 330 edgebander we have for sale. Contact us for further details. • Line workpiece capacity: • Length 250–3000 mm • Width 120–1200 mm • Thickness 8–60 mm • Edge bander (KAL 330) — base and transport • Continuous machine base; workpiece support with roller bar extendable ~800 mm Hfedpfxoytf Iro Abvjd • Transport chain 80 mm wide with rubber surface; precision guidance, hardened surfaces • Top pressure: driven belt • Technical data: • Feed speed 18–25 m/min • Working height 950 mm • Minimum working width: 55 mm at 22 mm thickness; 100 mm at 60 mm thickness (depending on workpiece length) • Workpiece overhang/supernatant 30 mm • Workpiece thickness 12–60 mm • Edge material from strip: 0.4–20 mm (max cross-section 900 mm²) • Edge material from coil: 0.3–3 mm (max cross-section: PVC 135 mm², veneer 100 mm²) • Max coil diameter 830 mm • Pneumatic connection 7–8 bar • Infeed system and controls (integrated with KAL 330) • Flexible workpiece infeed system wz10 for automatic infeed (lengthwise and crosswise); for precisely sized, square parts • Stepless infeed guidance adjustment (axis), speed set at input terminal • Automatic side adjustment of units (workpiece overhang 30–80 mm) for gluing and post-processing • Input terminal; solvent applicator top/bottom • Edge preparation and gluing • Pre-milling unit: 2 motors, each 4 kW, 150 Hz, 9000 rpm; electro-pneumatic control • Stepless vertical axis SF20 for automatic centering to panel thickness • Pre-melting unit with granule storage • Quick-lock system for QA/QE application unit; QA front glue storage for color change • Basic gluing unit A20; magazine height adjustment ±5 mm (manual spindle) • Extended magazine A6/A-E12/A20 for 2 coils (max Ø 830 mm); preheating station for QA/QE • Automatic pressure zone adjustment • Trimming and milling • Trimming unit HL84 with standing trimming stop for sensitive edges • Pneumatic trimming motor adjustment (2 positions: flush/level and with overhang for contour milling) • Pneumatic chamfer/straight changeover; manual side trimming stop adjustment when edge thickness changes • Rough milling unit: 2 motors stacked, each 1.5 kW, 200 Hz, 12,000 rpm; height adjustment via top pressure • Pneumatic 2-position setting: roughing with ~0.2 mm overhang / without overhang • Reserved free space for a fine milling unit • Contour milling unit Servo FK13 automatic: • 2 motors each 0.4 kW, 200 Hz, 12,000 rpm • Servo-controlled movements; automatic 8-fold tool changer • Feed speed max 20 m/min; minimum spacing between workpieces 500 mm • Workpiece thickness 12–60 mm • Automatic FK adjustment for identical radii on different edge thicknesses; auto retract • FK workpiece guidance with additional clamping for min part length 120 mm (single-sided) • Finishing and cleaning • Multi cleaning unit MN21 automatic: • Up to 3 profiles; tracing from top/bottom/side for chamfer and rounding on pre-milled PVC edges • Electropneumatic air nozzles; automatic chamfer/radius changeover; auto retract of upper/lower tool • Height adjustment via top pressure • PVC shavings separator top/bottom

Year of construction: 2015, condition: ready for operation (used), This 4-axis HOMAG PROFI BMG 511/60/12/R was manufactured in 2015. A robust CNC processing center featuring an 18-position tool changer, a drilling head with 30 spindles, and a dynamic table area allocation. It boasts a main milling spindle with a power of 12 kW and a speed range up to 24,000 rpm. Ideal for complex woodworking tasks with its extensive working area of 6,000 x 1,550 mm. Contact us for more information about this machine. Application Types Hfsdpfx Abex D Ra Hsved CNC Wood Machining

Condition: excellent (used), Year of construction: 1999, Clamping force: 25 tons Distance between tie bars: 270x270 mm Hfjdovl Skgepfx Abvjd Opening max: 275mm Min Mould height: 200 mm Mold platens size: 400 x 400 mm Screw diameter: 18 mm Injection volume: 20 cm3 Shot weight: 17 g Injection pressure: 2500 bar Working hours: 38.035 h

Condition: ready for operation (used), Year of construction: 2010, This HOMAG KAL 310/7/A3 was manufactured in 2010. A used single-sided edge banding machine featuring a 28-position ISAS edge magazine, PU gluing unit, and Boomerang return system. It includes a joint milling unit with two motors and a PU 34 gluing system with a capacity up to 6 kg/h. Ideal for precise edge banding applications. Contact us for more information about this machine. Hfodpfx Abox D Ra Tsved Application Types Edge Banding