Baler

HSM V-Press 860 Plus (2854)

Condition: new, Klanke Supercut roll splitter for efficient shredding of reject rolls. Features: -Automatic safety lock -Emergency stop rip cord -Siemens SPS Technical data: Blade length: 3000mm Lredsn I Rgpspfx Ahzol Cutting channel opening: 1200mm Motor power: 15kW Cutting force: 50to Order goods Price and further information on request. We will be happy to make you a non-binding offer.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Lredpfxjvf E Avo Ahzsl Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, Year of construction: 1976, turning diameter over bed 600 mm turning diameter over slide rest 400 mm turning length 1000 mm turning diameter in the gap 850 mm turning speeds 15 - 810 U/min centre height 300 mm spindle bore 56 mm total power requirement 9,0 KW weight of the machine ca. 2,9 t dimensions of the machine ca. 2,8 x 1,45 x 1,65 m Center lathe - Forkardt 3-jaw chuck F 315 - Single-jaw tool post Lodow Tdxcopfx Ahzorl - Steady rest - Live center - Chuck guard, limit switch monitored - Chip tray

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SF100s.01.26, screw diameter: 200 mm, total length: 3,200 mm, total height: 2,200 mm, overall weight: 400 kg, heating capacity: 10 kW (13.60 HP), pressure: 2 bar, type of input current: three-phase, input frequency: 50 Hz, input voltage: 380 V, warranty duration: 24 months, Machine for cheese streching, dozing, mozarella and other. Lredpfx Aot I Dxwshzjl

Year of construction: 2008, condition: excellent (used), SMG HZPU 8000-3000/2100-S1 Hydraulic Drawing Press Brand SMG Lodpfx Ajn Awd Rohzorl Type HZPU 8000-3000/2100-S1 Year 1995 Description Hydraulic Drawing Press H frame hydraulic press Pressing force 800 ton Clamping area Approx. 3,000 x 2,100 mm Installation height Max. 1,400 mm

Condition: new, Year of construction: 2022, functionality: fully functional, TAKAMAZ CNC Compact loader FC60 Lathe with automatic loader unloader quickest loading system in the world loading time new part 2,8 sec. loading cap. till 60 mm diameter. loading lenght max 50 mm max weight 1 kg per side loading feed 120 m min include part turning for loading Fanuc Control full warranty 2 year Lathe spec. Spindle motor 7,5/5,5 kw turning diameter max 180 mm turning lenght 240 mm bar cap. 35 mm collet chuck 173E till 40 mm diameter spindle nose A2-5 spindle speed 4500 rpm tool pos 8 stations tool shank 20x20 mm boring holder 25 mm diameter rapid speed X/Z 18/24 meter machine dimension 1,36 x 1,37 meter height 1,7 meter weight 2,7 ton total power 14 KVA Price is EXW (Stock Europe), Include loaded on truck. Transport, installation, commissioning, training, and yearly service contracts are available upon request for an additional fee. Installation and training is always done by our high qualified Service team in 3 locations in Europe. Netherlands, Germany, Romania. Lrjdpem E I D Hsfx Ahzel

Condition: as good as new (ex-display), Year of construction: 2008, machine/vehicle number: LSP 100T, Productions-Hydraulic press with H-column 100t with guidance Lrjdpfsg Rn Efox Ahzjl Manufacturer: Stenhoj Denmark Year of construction: 2008 Pressure force max. 1,000 kN / 318bar Press cylinder, stroke length: 400mm Press table with T-slot 1,500x900mm above 1,500x1,050mm below Stand passage 1,700mm Condition as good as new, the machine was only used for test runs and has been in stock since then. All statements without guarantee. Without transport costs.

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Ljdstvat Tepfx Ahzorl After refurbishment, this baler is sold with a 2-year warranty.

Condition: new, functionality: fully functional, Year of construction: 2026, AT SERIES Entry-level fiber laser metal sheet&tube cutting machine One machine with two uses. AT series cuts both metal sheets and metal tubes. Sheet&tube laser cutting machines A-T Series Function Enhancement Sheet&tube laser cutting machines A-T Series Expert High Speed Cutting Database Fast air cutting efficiency increases by 37% when cutting carbon steel. Sheet&tube laser cutting machines A-T Series Active Anti-collision Function Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Sheet&tube laser cutting machines A-T Series Bodor Lightning The lightning-quick piercing process combined perfectly with BodorGenius completes the whole piercing just during the laser cutter head moves down on Z-axis. Sheet&tube laser cutting machines A-T Series No Quiver when Cutting Thin Sheet The cutting process works even at the edge of thin sheets, and ensures no chatter marks. Sheet&tube laser cutting machines A-T Series Angle Steel and Channel Steel Cutting Angle steel and channel steel cutting are standard with no need fior additional installation. Sheet&tube laser cutting machines A-T Series Lrsdpfjhtyutsx Ahzsl Four-side Edge Searching, Higher Precision Optimized edge searching method and algorithm guarantee higher cutting precision and better steadiness of the laser cutter. Mechanical Configuration Sheet&tube laser cutting machines A-T Series Stretching Aluminum Crossbeam Ultra-high-pressure stretching process and lightweight design; Rigidity increases by 60% ; Weight goes down by 20%; Laser cutter running speed increases by 50% Sheet&tube laser cutting machines A-T Series Modular Table The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. Sheet&tube laser cutting machines A-T Series Penumatic Chuck Cutting machine clamping becomes convenient, easy and fast, with 3 seconds at the soonest to clamp and high repeat precision Software BODORTHINKER BodorThinker BodorThinker is a high-end intelligent control system for a CNC laser cutter, featuring reliable stability, convenient installation and adjustment, safe production, multiple functionality, and robust performance. With BodorThinker, your laser cutting solutions can be modular, customized, automated and information-based. Design Industrial Design Award Winner "Oscar in Design", two of the top three world industrial design awards Remote Control A mango shape and convenient magnetic securing help you control with just one hand.

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours, as of March 2025 Main press force: 85 t Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying system: 5-fold vertical Lrsdpfxev T I Eve Ahzjl Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Your service team at Mertens & Frowein GmbH