Anvil with rounded horn and rectangular horn; anvil in North German design, pointed horn

160

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 020033, spindle speed (max.): 5,000 rpm, spindle diameter: 110 mm, controller model: Siemens SINUMERIK, empty load weight: 11,000 kg, counter spindle speed (max.): 5,000 rpm, The machine is expected to be available for approximately €4,000, including loading onto a truck (FOB). TECHNICAL DETAILS Iijdpfezdqdfsx Ag Uec Working area X1-axis: 1,190 mm Working area Y1-axis: 120 mm Working area Z1-axis: 260 mm Working area X3-axis: 540 mm Working area Y3-axis: 120 mm Working area Z3-axis: 260 mm Handling space X1-axis: 490 mm Axes and Feed Feed force X1/Z1/Y1: approx. 8/10/10 kN Feed force X3/Z3/Y3: approx. 8/10/10 kN Rapid traverse speed X1/Z1/Y1: approx. 80/40/7.5 m/min Rapid traverse speed X3/Z3/Y3: approx. 40/40/7.5 m/min Acceleration X1/Z1/Y1: 7/7/7 m/s² Acceleration X3/Z3/Y3: 7/7/7 m/s² Spindle Speed at main and counter spindle: 5,000 RPM Power at 100% duty cycle, main spindle: 20 kW Torque at 100% duty cycle: 105 Nm Power at 40% duty cycle: 27 kW Torque at 40% duty cycle: 145 Nm Spindle bore: 65 mm Spindle diameter at front bearing: 110 mm Spindle nose diameter (cylindrical): 140 mm Hydraulic full-stroke cylinder OVS80 - Main spindle Piston stroke: 32 mm Piston area: 34.36 cm² Clamping pressure: 8 to 80 bar Tensile or compressive force at 80 bar: max. 27.2 kN Leakage oil volume at operating pressure 80 bar: max. 2.2 l/min Hydraulic full-stroke cylinder OVS65 - Counter spindle Piston stroke: 32 mm Piston area: 26.1 cm² Clamping pressure: 8 to 100 bar Tensile or compressive force at 100 bar: max. 26.1 kN Leakage oil volume at operating pressure 100 bar: max. 3 l/min Y-axis Slide travel: 120 mm Feed force: 10 kN Rapid traverse: 7.5 m/min Resolution: 0.05 mm Speed of driven tools: 6,000 RPM MACHINE DETAILS Control system: Siemens SINUMERIK Unloading device Swivel angle: 90 degrees Swivel time: 2 s Slide travel: 100 mm Rapid traverse speed: 6 m/min Workpiece weight: approx. 10 kg Workpiece diameter: 200 mm Electrical data Rated power: 45 kW Apparent power: 53 kVA Rated current: 76 A Voltage: 400 V Frequency: 50/60 Hz Dimensions and weight Dimensions with chip conveyor (L x W x H): 2,770 x 4,435 x 2,750 mm Weight: approx. 11,000 kg EQUIPMENT Two tool holders with 12 tool positions each, VDI 30 Note: Further technical data can be found in the attached data sheet. The machine is not equipped with a B-axis.

Condition: used, Year of construction: 2003, turning diameter max. 420 mm turning length 1090 mm control FANUC Serie 18i-TB Iiodpfeucgylox Ag Ujc turning spindle Durchlass 108 mm 250 / 315 turning speed range 0-3750 U/min Feed speed 18/24 m/min. workpiece 12 quill stroke 100 mm diameter of quill 110 mm taper MK 4 number of driven tools 12 mm turning speeds 3000 U/min 22 nm coolant tank 140 l total power requirement 22/18,5 kW weight of the machine ca. 6500 KG

Condition: used, Year of construction: 1994, pressure 160 t chamfer lenght 3050 mm distance between columns 2550 mm stroke 400 mm throat 250 - 400 mm Iijdpfxszfav To Ag Uoc weight of the machine ca. 15.400 kg

Condition: new, functionality: fully functional, Features of the Unit 1. Chain conveyor belt, 2 meters in length (other lengths available on request) 2. Adjustable bag former 3. Single film loader + automatic film centering device 4. Rotative end sealing unit, double sealing jaw 5. Robust, central fin seal structure 6. Three servo-controlled drives 7. HMI control panel 8. Two individual temperature controllers Ijdpfxjydqahs Ag Ueic 9. Housing made of 304 stainless steel 10. Documentation in the local language 11. Print mark control 12. Programmable bag length 13. Standard running direction: left to right Technical Specifications 1. Product length: L90–300 mm 2. Product width: W30–160 mm 3. Product height: H5–55 mm 4. Packaging speed: up to 125 products/min (depending on product, bag length, material, and number of sealing jaws) 5. Maximum film width: 370 mm 6. Supply voltage: 1Ph. 220V 50Hz 7. Power consumption: approx. 6.5 kW 8. Machine weight: approx. 400 kg 9. Machine dimensions: approx. 3500 x 950 x 1450 mm

Condition: excellent (used), Maximum machinable diameter above the bed: 575 mm Iodpfxjwlgdye Ag Ueic Maximum machinable diameter above the slide: 525 mm Maximum machinable diameter above the small cross slide: 300 mm Distance between centers: 2000 mm Spindle passage diameter: 51 mm Number of spindle speeds: 18 Spindle speed range: 32 to 2500 rpm Bed width: 400 mm Maximum cross slide travel: 305 mm Maximum upper slide travel: 140 mm Maximum tailstock travel: 150 mm Overall dimensions: 3405 x 1175 x 1345 mm Machine weight: 2200 kg

Condition: repair required (used), Hydraulic vise, machine vise, NC compact clamp -Handover in its current condition as inspected Iiedpfx Aob A Ik Dog Uoc The vise has no spindle and is therefore sold as a source of spare parts. -4x clamping jaws: 200 x 60 mm -2x clamping jaws: 160 x 50 mm -Dimensions: 530/160/H165 mm -Weight: 104 kg

Condition: used, Year of construction: 1992, functionality: fully functional, Weiler Praktikant 160 B Lead and Draw Spindle Lathe, built in 1992, with a new 3-axis digital display from K&C, from a vocational training workshop! Technical data: >> Year of manufacture 1992, Machine No. 92-160-2994 >> Center height 160 mm >> Distance between centers 650 mm >> Spindle speeds: from 24 to 2500 rpm >> Spindle bore 40 mm >> Short taper spindle head, DIN 55027, size 5, with bayonet lock >> Tailstock, MK 3 >> Feeds from 0.02 to 0.63 mm/rev >> Possible threads: metric, inch, module, and diametral pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight approx. 680 kg >> Spindle brake, switchable >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital display from K&C with operating manual Functions: Switching mm/inch, coordinate selection ABS/INC, halving of the display value, reference mark, tool programming 200 pieces, taper calculation, radius/diameter, quick zeros, switching of the counting direction >> 3-jaw chuck 160 mm with 1 set of jaws >> Tool clamping system with 2 steel holders >> Bed stop >> Centering point >> Coolant system >> Rear panel >> Machine feet >> Electronic spindle protection Iedpfozd Tycox Ag Usic >> Operating manual Additional accessories such as collets, 4-jaw chucks, steady rests, and more are available at an extra charge. For safety: Electronic spindle protection, cover for the lead and draw spindle, 2 emergency stop buttons, spindle brake, electronic door protection for the change gears. About the machine: Offered is a Weiler Praktikant 160 B lead and draw spindle lathe in very good condition. All slides run smoothly and evenly. Even at high speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and allows surfaces to be produced that are as smooth as if they had been ground. Take advantage of the opportunity to inspect this machine on-site while it is powered up and see its condition for yourself.

Condition: good (used), NHH lathe Turning diameter bed: 260 mm Turning diameter support: 160 mm Spindle bore: 26 mm Iodpfx Agemw Ukcj Usic Turning lenght: 600 mm Heidenhain digital measurement Diameter faceplate: 155 mm Speed: 2000 RPM Dimensions: 150x85x155 cm LxWxH

Condition: good (used), Year of construction: 1994, functionality: fully functional, Press force: 160 t Bending length: 3050 mm Distance between uprights: 2550 mm Iodpfx Agszd S Tzs Uoic Stroke: 400 mm Overhang: 250 - 400 mm Machine weight approx.: 15,400 kg Equipment: -Hydraulic tool clamping, top and bottom -Cybelec DNC 900 control system -Die shifting -Compensation -2-hand foot control -Controlled axes: y1, y2, x, R, z1, z2 -Tool set

Condition: reconditioned (used), functionality: fully functional, warranty duration: 6 months, input voltage: 400 V, DGUV certified until: 08/2027, year of last overhaul: 2026, input frequency: 50 Hz, empty load weight: 700 kg, overall weight: 700 kg, type of input current: three-phase, power: 12 kW (16.32 HP), electrical fuse: 32 A, Spiral mixer Diosna Top model: SP 160 D Dough machine with 2 speeds, 2 timers Robust technology! Flour dust cover Connection 400V, 32A-CEE plug Used machine, refurbished with warranty + service Optional: Maintenance contract Spare parts box Delivery service Training & commissioning Loan machine service Leasing & rental service Iiodpfx Agjvvqqte Usc Many top spiral mixers in stock!

Condition: good (used), Heavy-duty lathe, lathe, lathe, lead and tension spindle lathe, lead and tension spindle lathe, automatic lathe -Manufacturer: WMW, automatic lathe type DRT 50m -Turning length: 550 mm -Turning Ø over bed: 530 mm -Spindle bore: Ø 63 mm -Spindle speeds: 9 - 450 rpm -Three jaw chuck: Ø 200 mm -Turret: with accessories, see photos -Drive motor: 5.3 / 6.8 kW -Dimensions: 2420/1040 / H1460 mm -Weight: 2200 kg Ijdpfsha Hvvsx Ag Ueic

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 92600 € 1750.14 € 160 to 6 mm 750 mm 1100 mm 230 mm 1 - 172 mm 45 1/min 6 100 mm 80 mm 375 mm 540 mm 11 kW 1890 mm 1950 mm 3650 mm 15500 kg Welded steel frame construction 6-fold ram guide Pneumatic clutch-brake combination Protective enclosure with light barriers and side doors Iedpfx Aewiqu Rjg Ueic Mechanical overload protection Two-hand and foot pedal operation Manual stroke adjustment Motorized ram adjustment Variable stroke rate via frequency converter Operating modes: * Adjustment mode * Two-hand release * Foot release * 2-stroke operation via light barriers * Continuous operation Touchscreen for * Stroke counter with preselection for continuous operation * Stroke rate adjustment * Lubrication intervals and duration * Alarm messages * Motor direction of rotation * Monitoring of inputs and outputs 2 free cams for connecting peripherals Automatic central lubrication Equipment in accordance with CE regulations Symbolic photos, picture incl. optional available bolster plate OPTIONS: vibration pads € 192,00 bolster plate o.r. hydr. overload safety device o.r. etc.

Year of construction: 2008, condition: ready for operation (used), pressing force: 163 t, stroke length: 700 mm, Hydraulic 4-Column Press manufactured in 2008. This Hymag HS 4 160 features a press force of 1,600 kN and a stroke of 700 mm, making it suitable for metal pressing applications. It is equipped with a PLC-controlled system for enhanced operation. If you are looking to get high-quality metal forming capabilities, consider the Hymag HS 4 160 machine we have for sale. Contact us for further details. • Manufacturer: Hymag • Machine Type: Hydraulic 4-Column Press • Hydraulic Pressure: 280 bar • Main Motor Power: 55 kW • Voltage: 400 V • Current: 96 A • Secondary Motor Power: 7.5 kW Iedpfx Agszd Ez Es Ueic • Voltage: 400 V • Current: 15 A • Oil Capacity: 600 L • Control System: PLC-Controlled Hydraulic Press

Condition: excellent (used), Height adjustment for vise (28660) Mounting surface for vise diameter 180 mm Hole distance 145 mm Mounting surface for workbench 180 x 135 mm Weight 10.5 kg Iodpfow Ic Hhjx Ag Ujic

Year of construction: 2013, condition: ready for operation (used), pressing force: 163 t, stroke length: 700 mm, Hydraulic 4-Column Press manufactured in 2013. This Hymag HS 4 160-K features a press force of 1,600 kN and a stroke of 700 mm, making it suitable for metal pressing and forming applications. With a main motor power of 55 kW, this machine is designed for efficiency and reliability. If you are looking to get high-quality metal pressing capabilities, consider the Hymag HS 4 160-K machine we have for sale. Contact us for further details. Iijdpfxozd Ezlj Ag Uoc • Manufacturer: Hymag • Machine Type: Hydraulic 4-Column Press • Application Type: Metal Press / Forming Press • Hydraulic Pressure: 305 bar • Main Motor Power: 55 kW • Voltage: 400 V • Current: 105 A • Secondary Motor Power: 7.5 kW • Voltage: 400 V • Current: 15 A • Cooler Motor Power: 1.5 kW • Voltage: 400 V • Current: 5.1 A • Oil Capacity: 600 L