Machining center

MAKA PE 70

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Gujdpfxexy Tmnj Agpeb

Condition: used, machine/vehicle number: 007716, X axis working area: 3250 mm Y axis working area: 1220 mm Working Table: Pod and Rail Main Electrospindle power: 12 KW Gusdpfx Agowuz N Nopsb Number of controlled axes: 4 axes Total number of drilling spindles: 18 Total number of tool changer positions: 16

Condition: used, machine/vehicle number: 008319, X axis working area: 6380 mm Y axis working area: 1380 mm Working Table: Pod and Rail Main Electrospindle power: 11 KW Number of controlled axes: 5 axes Gedpfxjx A Tc Ij Agpsub Total number of tool changer positions: 32

Year of construction: 1999, condition: used, machine/vehicle number: 942, - Manufacturer Fladder - Type Gyro 300 VAC Ex - Working width 1300 mm - Year of manufacture 1999 - Number of brush heads 6 pcs. - Rotating and oscillating grinding unit - 2 vacuum fans - Motor power 7.5 kW - With vacuum conveyor belt - Electrical connection control cabinet - Feed continuously adjustable 2 - 8 m/min - Length 2070 mm - Width 2370 mm - Height 2240 mm - Weight 2300 kg - Separate control cabinet, Guedovvl H Njpfx Agpjb Dimensions: W: 800 mm, depth: 400 mm, height: 1700 mm - Location, in the warehouse - Volt, HZ 400 / 50

Condition: good (used), BIESSE ARROW ATS 5 AXIS NC1000 MACHINING CENTER Gjdpfeukcy Ejx Agpeub Machining head with revolver tool change BH39 drilling machine, 250m3 vacuum pump (this machine had been in operation for 10 years in a woodworking school)

Condition: ready for operation (used), Year of construction: 2021, travel distance X-axis: 4,000 mm, travel distance Y-axis: 1,670 mm, travel distance Z-axis: 500 mm, number of axes: 4, This 4-axis CNC processing center was manufactured in 2020. It features a 12 kW milling spindle with a speed range of 1000-24000 rpm and a C-axis rotation of 0-360°. The machine includes a 12-station linear tool changer and a comprehensive drill head with 16 spindles. It also boasts a robust safety system with a light barrier. Consider the opportunity to buy this Felder Format 4 Profit H 200 CNC processing center. Contact us for more information about this machine. • Automatic central lubrication • Working area: X 3300 mm / Y 1280 mm / Z 250 mm (clearance height from console level depends on clamping system) Gujdpfox D D Hmex Agpsb • Operating terminal on left side of machine • Hand terminal with axis speed control and emergency stop • Software: Woodflash (CNC board, tool database, program editor) • Positioning display for workpiece support and vacuum suction cups • Vacuum connection for template milling (left side), connection diameter 12 mm • Vacuum pump: 1x, total suction power 90 m³/h @ 50 Hz or 108 m³/h @ 60 Hz • Milling spindle: 12 kW (S6), HSK F63, 1000–24,000 rpm, full rated power at ~12,000 rpm, air-cooled; C-axis 0–360° • Tool changer: 12-station linear on left side of machine stand, incl. pickup space for aggregates; max tool diameter 250 mm; max tool length 240 mm • Drill head DH 16 4H 2S: 12 vertical spindles (7X / 5Y); 4 horizontal spindles (2X / 2Y); pre-stroke 70 mm; drilling length 70 mm; shank Ø 10 mm • Groove saws: 2 (one X, one Y); max blade Ø 120 mm; max thickness 5 mm; continuously variable speed up to 7,500 rpm • Safety: front light barrier system

Condition: used, Year of construction: 2008, · Working area X-Y-Z: 3,660 x 1,550 x 130 mm · Travel length X-Y: 4,200 x 2,000 mm Description of the units and accessories (base) The structure of the base body is a monolithic construction made of thick-walled steel. It is stiffened by welded triangular plates across the entire machine bed, making it extremely stable. The triangular shape used for load-bearing parts, with a large base, is the secret to ensuring lasting precision and stability. The machine layout allows the user an optimal workflow despite minimal space requirements. The base body constructed in this way therefore offers the machining unit a balanced and secure base with particularly good load distribution. The mobile unit carrier in gantry design is made of a solid monoblock. It is positioned in the X direction on prismatically ground guides via recirculating ball slides. The work unit is mounted on this mobile unit carrier on prismatic, ground guides and a recirculating ball slide. Axis movement: The drive system in the Y and Z axes is provided by ground, high-precision recirculating ball screws. The X-axis is driven by a backlash-free, preloaded precision rack and pinion drive. This ensures balanced load distribution during the positioning process. This characteristic is important for ensuring balanced movement even in more complex tasks. The various axes are driven by brushless three-phase servo motors/brushless AC motors. These offer excellent positioning speeds thanks to very short ramp times. Furthermore, the measuring system is fully integrated into these motors. These properties make this type of drive completely maintenance-free. · Rapid traverse in X: 40 m/min · Rapid traverse in Y: 60 m/min · Rapid traverse in Z: 22.5 m/min Vacuum system (basic) · Vacuum pump: 100 cbm/h · Power: 2.5 kW · Max. negative pressure (connection) 0.9 bar Control / control cabinet · Office PC or industrial PC (see options) · Basic NC control: ESA-GV KVARA 6.0 · Cable remote control with the most important functions ELECTRIC/ELECTRONIC CNC CONTROL Universal is equipped with a powerful NC control. The integrated office PC gives the NC control an unparalleled level of familiarity: the software runs on Windows XP and allows quick and easy programming, which is easy to learn even for inexperienced users. The system is open and allows the connection of CD-ROM drives, audio cards, barcode readers, modems, printers, scanning systems, etc. Furthermore, the installation of all network systems, as well as all commercially available CAD programs, is possible. To reduce space, the control cabinet is located under the machine table, and the operator works at a separate terminal on casters, which can be freely positioned. XILOG PROGRAMMING SYSTEM Software features: - Import of DXF files - Import of ASCII files - User interface in the operator's native language (available for languages I - GB - F - D - E) - Linear and circular interpolation in three axes, linear in space, spiral in the selected plane - Assisted programming - Calculator for direct transfer of calculated data - Graphic and syntax aids for drilling and milling operations - Parametric programming to perform the same panel machining on different Guodpfx Ajvvi Rfsgpjb

Condition: ready for operation (used), Year of construction: 2007, travel distance X-axis: 4,600 mm, travel distance Y-axis: 1,935 mm, travel distance Z-axis: 275 mm, number of axes: 5, This 5-axis Biesse Rover C9.50 was manufactured in 2007. It features a large working area (X=4600 mm, Y=1935 mm, Z=275 mm), an automatic lubrication system, and a control unit for 5-axis interpolation. The machine includes a vacuum system, a conveyor belt for chip removal, and a liquid cooling unit. If you are looking to get high-quality CNC machining capabilities, consider the Biesse Rover C9.50 machine we have for sale. Contact us for more information. Worktable and clamping • 8 ATS plate holders (L = 1525 mm) and 24 slide rails Guodpfxsx D H Hce Agpeb • Automatic positioning of plate holders and slide rails (EPS X-Y) • Pneumatic locking system, divided into 2 working areas in X • 8 rear reference stops, stroke 115 mm • 8 stops, stroke 140 mm, positioned at 1175 mm (L = 1280 / 1525 / 1800 mm) • 8 stops, stroke 140 mm, positioned at 770 mm (L = 1280 / 1525 / 1800 mm) • 4 side stops, stroke 140 mm (2 left + 2 right), with pneumatic system • 4 removable center stops, stroke 140 mm (2 left + 2 right), with pneumatic system • Sensor for detecting lowered stops • Pneumatic system for lifting bar holders • 6 lifting bar holders for easy loading (H = 74 mm modules)Vacuum • Vacuum system for a 250 m3/h pump • 250 m3/h rotary vane vacuum pump for standard vacuum systemMachining units and configuration • Composition C3-A1: • Device for mounting chip deflectors with pneumatic or inductive sensors on a 5-axis machining unit • Flange for mounting units on a work unit with 5 interpolating axes (units usable only when the electric spindle is vertical) • Composition C3-P2: • Additional Z slide for rear work units, controlled by an independent Z axis • 16 vertical and 4 horizontal boring spindles in Y-direction • Chain tool changer with 22 positions (180 mm center distance) • Iron gripper for chip deflector with pneumatic or inductive sensor, positioned in the chain tool changer • RH chip deflector with inductive sensor for standard electric spindle or 15 kW 5-axis electric spindle (requires device for chip deflector; requires flange for mounting units when using a 5-axis electric spindle; requires C-axis when using a standard electric spindle)Systems • Automatic lubrication system • Control unit with 5 interpolating axes Additional equipment • additional refurbished 5-axe main spindel available • Conveyor belt for removing chips and scrap pieces (chip conveyor) • Liquid cooling unit for liquid-cooled systems (can cool two electric spindles, or one electric spindle plus one liquid-cooled drilling head)Note: The technical data and descriptions are taken from the original order confirmation and are for information only; they are not binding.

Condition: used, Working width 410 mm Length of the planing table 1450 mm Number of knives 4 St. Motor output 4 kW Dimensions (L/W/H) 2650x850x1100 mm weight of the machine ca. 750 kg Surface planer F 410 N ----- Technical manufacturer's description: Planing width: 410 mm Total table length: 2600 mm Table height: 855 mm Feed table length: 1450 mm Aluminum planing fence swivels up to 45° Planing fence dimensions: 1100 x 170 mm 4-knife planing shaft diameter: 120 mm Knife shaft speed: 5000 rpm Godpowzmu Dofx Agpoub Motor power: 4 kW TERSA monobloc one-way reversible cutterhead SCM dressing protection device integrated in machine stand 120 mm diameter extraction nozzle Manual star-delta switch Motor protection switch, undervoltage release Lockable main switch Automatic motor brake Pivoting auxiliary fence ----- Price of the above machine on request! ----- (technical data according to manufacturer - without guarantee!) All prices quoted are net and subject to VAT.

Condition: used, power: 64 kW (87.02 HP), fuel type: diesel, lifting height: 12,600 mm, Year of construction: 2008, operating hours: 7,932 h, Technical information Make of engine: Perkins Guodpjyikdbofx Agpob Top speed: 40 km/h Empty weight: 9.100 kg Functional Lifting capacity: 3.800 kg Identification Serial number: B8157268 Other information Front tyres / undercarriage remaining: 50 Rear tyres remaining : 50 Tyre brand: - Transport dimensions (LxWxH): 6.95x2.22x2.44 Additional information Please contact PFEIFER GROUP for more information