Used Albert Goecker Kg for sale (70,100)

Condition: good (used), CV saws grinder Albert Göcker Gedpfx Aequtd Rjbdobg

Year of construction: 2003, condition: good (used), functionality: fully functional, machine/vehicle number: 03234, 6 Brush ( 3 pairs) descaling machine for steel wire size 5.5mm - 16.0 mm max (low carbon) Brush pairs arranged in a 60 degree offset for maximum effect. Gbodpfjx R Uzdox Abdeg A very clean looking machine. On site viewing and inspection recommended

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Gsdpjx A U Ncofx Abdobg Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: new, Year of construction: 2025, Hand pallet truck 2000 kg LWPW with weighing system, new 2025. Continuous stock, see our website. Prices are ex Nuland. Van de Wert Trading B.V. has a variable stock of machines, trucks, trailers, and attachments. All deliveries are offered at trade prices in AS-IS condition without warranty. (see our general terms and conditions) For a viewing and/or test drive, you can schedule a non-binding appointment. Please call in advance, as we are not always present. Gbjdpex Td Dtjfx Abdjg Van de Wert Trading B.V. Bedrijfsstraat 3 5391 LR Nuland

Condition: new, 21.25 m² storage platform incl. stairs, railings on two sides, top edge 300 cm, 500 kg/m², immediately ex warehouse, accessible with pallet truck, system platform, steel platform, storage level Data : - Length: 5000 mm - Width: 4250 mm Gjdpfx Abjx Thlujdobg - Size can be extended on request - Clear height below the platform: 2612 mm - Support grid: 4605 x 3850 mm - Plus 200 mm overhang of the floor covering - Supports, stairs, railing posts, cross bracing & dome struts powder-coated in RAL 7016 - Handrail, knee rail, roll-off edge, main & secondary beams galvanized - Floor covering: 38 mm chipboard P6, OK natural & UK white - New from stock Wietmarschen - AVAILABLE IMMEDIATELY Storage platform consists of : - 04 x upright - 02 x main beam C+350 - 06 x secondary beam S+260 - 01 x intersection - 02 x strut brace - 10 x Chipboard - 01 x Stairs, 37° incline - Approx. 8.25 running meters Railing - Incl. connecting material & screws -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 5026,00 € net 5980,94 € gross You will receive an invoice with VAT shown. Transportation : The delivery is carried out on request by our partner forwarding agency, the costs for this depend on the postal code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation. Are you interested or do you have any questions? Simply contact us by message or phone call. You can find our telephone number on our company page. ☎️ You can reach us by phone from Monday to Friday, 08:00 - 15:00. Alternatively, you can send us a message with your name and number and we will get back to you as soon as possible.

Condition: new, The scope of delivery includes: 01x wire grating, new Material color: sendzimir galvanized Execution: laid-on shelf grating, folded on both sides total depth: 1.112 mm Gbedjilk Ngopfx Abdog clear span: 1.000 mm total width: 890 mm mesh size: 106 x 72.5 mm wire thickness: 3,8 mm Number of beams: 4 pcs. Unit weight: approx. 5.14 kg Technical data: Tested load capacity: 500 kg according to ANSI MH 26.2 for beam depth: 1.100 mm Assumed beam width: 50 mm Application for indoor use only Possibility of use: Shelf size/ modules required per shelf 1,100 x 1,800 mm/ 2 pcs. 1,100 x 2,700 mm/ 3 pcs. 1,100 x 3,600 mm/ 4 pcs. Heat resistant sheets: On request, we can offer you heat resistant sheets (see picture material) for sale; prices on request. Fire protection has special requirements. Therefore, the wire meshes can be provided with a welded-on heat shield. And should you need a push-through protection for cardboard boxes, the heat shield can also be made with a bend. General information about the article: This item is offered for pickup only. Any additional transport or shipment of this article is subject to additional costs, which will be charged separately to the customer. depending on the delivery location or scope of delivery can be requested from us.

Condition: like new (used), functionality: not functional, load capacity: 6,500 kg, Load capacity 6500 kg Please note: Arm diameter adjustable from 1880 mm to 4550 mm (swivel-out) Space-saving and continuously adjustable, the extension arms can be locked in place Speed continuously adjustable from 0.001 to 5 rpm Motor power 3 kW Torque 15000 Nm Height 800 mm Maximum current transmission 2000 A Weight 4700 kg Gbjdpox Thucsfx Abdog with hand and double-foot remote control CE certificate, declaration of conformity, documentation, circuit diagram with original 2016 quotation invoice Current new price approx. €28,000

Condition: new, Year of construction: 2025, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Gbedpfx Abjndn Agsdsg Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 600-700 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: reconditioned (used), Year of construction: 2014, operating hours: 5,612 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total height: 2,800 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), volume flow: 332 m³/h, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,612 hours, stand August 2025 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press was partially overhauled and tested in our workshop, see photos and our function video. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors. Gbsdpjvtpq Hefx Abdsg

Condition: reconditioned (used), Year of construction: 2005, operating hours: 15,604 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,050 mm, filling opening length: 1,250 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 700 mm, bale weight: 500 kg, total width: 1,700 mm, total height: 2,400 mm, total length: 7,800 mm, input voltage: 400 V, input current: 64 A, overall weight: 12,500 kg, transport height: 2,400 mm, power: 30 kW (40.79 HP), year of last overhaul: 2024, volume flow: 160 m³/h, transport width: 1,700 mm, transport length: 7,800 mm, tank capacity: 600 l, Hello, We are offering you a used baler from the manufacturer Presto GmbH & Co. KG, type HPK 50 B, subject to change. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer Presto GmbH & Co. KG Type HPK 50 B Year of manufacture 2005 Pressing force of main press 50 t Drive power 30 kW Total connected load 31.5 kW Rated current 64 A Throughput under operating conditions with a bulk weight of 60 kg/cbm approx. 6.7 t/hour Machine weight of press 12.5 t Note: The machine is currently in our workshop for overhaul and is expected to be tested and ready for sale in February. The machine documentation is available in German. A viewing of the press is possible by appointment in our workshop. Gbsdpfxjuan Hzj Abdsg We would be pleased if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: good (used), Feeder for round material, round material feeding system, round steel feeding system, motorized reel for round material for eccentric press, hydraulic press for straightening machine, wire straightening machine, unwinder straightening machine combination, unwind reel, wire unwinder, double reel, reel, unwind reel, motorized reel for wire processing, punch press, eccentric press, hydraulic press, automatic punch press, motor reel, winding reel, unwind reel, wire unwinder -Round material feeding system: Round steel feeding system with console -Feed: Drive Lenze 2.2 kW type MDXMA2M Belt tension: pneumatic -Material stress: hydraulic -Tension rollers: for Ø approx. 25 mm -Individual components: see photos -Hydraulic power unit: can be supplied for an additional charge -Transport dimensions: 900/500/H780 mm -Weight: 332 kg Gjdpfx Aei Exp Ejbdsbg

Condition: new, The scope of delivery includes: 01x wire grating, new Material color: sendzimir galvanized Execution: laid-on shelf grating, folded on both sides total depth: 1.112 mm clear span: 1.000 mm total width: 890 mm mesh size: 106 x 53 mm wire thickness: 3,8 mm Number of beams: 7 pcs. Unit weight: approx. 7.53 kg Technical data: Tested load capacity: 1,000 kg according to ANSI MH 26.2 for beam depth: 1,100 mm Assumed crosshead width: 50 mm Application for indoor use only Possibility of use: Shelf size/ modules required per shelf 1,100 x 1,800 mm/ 2 pcs. 1,100 x 2,700 mm/ 3 pcs. 1,100 x 3,600 mm/ 4 pcs. Heat resistant sheets: On request, we can offer you heat resistant sheets (see picture material) for sale; prices on request. Fire protection has special requirements. Therefore, the wire meshes can be provided with a welded-on heat shield. And should you need a push-through protection for cardboard boxes, the heat shield can also be made with a bend. General information about the article: This item is offered for pickup only. Any further transport or shipment of this Gbodpfx Absilk Nredsg or a shipment of this item is associated with additional costs, which are separately depending on the delivery location or scope of delivery can be requested from us.

Year of construction: 2026, condition: as good as new (ex-display), The BTS-Tyre Packing Machine Gen.2 is ideal for used tyre companies with large tyre volumes. The triple machine is the perfect solution for cost-effective disposal or resale of second-hand tyres. By doubling or tripling the tyres you achieve an enormous volume reduction, the available storage and loading capacity, as well as the permissible transport weight can be used much more efficiently. Godpfxsb Rz R Uo Abdsbg Pressing cylinder: Pneumatic Pressing force: 1.23 kN, adjustable Machine size: 1250 H x 1930 W x 660 D mm Machine weight: 93 kg Transport size: 1250 H x 1200 W x 800 D mm Working height: 800 - 1020 mm, adjustable Power supply: Air, up to 10 bar / 145 Psi Working pressure: 6 - 8 bar User-friendly and safe two hand control Strong and long-life design High-performance pneumatic cylinder Ball bearing roller guides Adjustable working height Low noise level by silencer Air quick connector A quality product “Made in Germany” Suitable for doubling and tripling Second-hand tyres Optional extras Machine colour RAL BTS-MF550HD Scrap Tyre Baler Demo-Video shows BTS-Tyre Packing Machine Gen.1, the BTS-Tyre Packing Machine Gen.2 operates on same way. Tyre packing machine, Tyre triple machine, Tyre double machine, Tyre doubler, Tyre tripler, Tyre packer, Tire packing pachine, Tire tripling machine, Tyre doubling machine, Tire doubling machine

Condition: new, Year of construction: 2026, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 800-900 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Gbodpjng Exaefx Abdjg Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: used, Year of construction: 2006, functionality: fully functional, machine/vehicle number: 13-3188, total length: 160,000 mm, total height: 3,000 mm, total width: 9,000 mm, temperature: 230 °C, volume flow: 100 m³/h, Powder Coating System ARNO HERING PTR 15-45-SE (Year 2006) For sale is a complete powder coating system from ARNO HERING (model PTR 15-45-SE), manufactured in 05/2006. The system consists of an application booth, drying/curing oven, and crane rail/carrier racks (hanging racks). The system is from ongoing production and is suitable for coating metal parts and assemblies. Highlights / Equipment (Components): - Application booth (powder application) Gbodpfsx Squ Aox Abdog - Drying oven / curing oven - Crane rail / manual overhead conveyor system including carrier/hanging racks - Documentation/control manuals: to be included if available Technical Data (according to nameplate): - Model: PTR 15-45-SE - Year of manufacture: 05/2006 - Machine number: 13-3188 - Max. drying temperature: 230 °C - Minimum exhaust air volume (at 20 °C): 100 m³/h - Max. permitted powder quantity: 10 kg/h Notes: - Inspection on site is possible by appointment. - Loading/dismantling: by arrangement (possibly to be handled by the buyer). - Sale ex location, subject to prior sale. We are offering this used ARNO HERING PTR 15-45-SE powder coating system, year 2006. Model: PTR 15-45-SE Year: May 2006 Machine number: 13-3188 Maximum drying temperature: 230 °C Minimum exhaust air volume at 20°C: 100 m³/h Maximum permitted powder quantity: 10 kg/h If you have any questions or need further information, please feel free to send us a message or call us.

Condition: new, Year of construction: 2026, Dump belt blast wheel blast machine 7,5 kW direct driven indexing turbine with 8 throwing blades. Belt width 700mm and Ø600mm Gedpfxog S Rt Ee Abdsbg

Condition: used, tank capacity: 2,950 l, GENERAL Equipment: Crane lugs Design: suspended Remarks: 4 feet made of V2A; total height stated is estimated Speed: 1475 rpm Outer diameter: 1,600 mm Inner diameter: 1,400 mm Total height: 3,500 mm Heating/cooling: available Insulation: available Power: 15 kW Max. permissible operating temperature: 151 °C Max. permissible operating overpressure: 5.0 bar Max. overpressure: 2.5 bar Agitator: Dissolver Support type: feet Location: Bremen Technical documentation: drawing, TÜV papers Cylinder temperature control: double jacket Nameplate: Vacuum: 0.9 bar Volume: 2,950 litres Double jacket volume: 148.0 litres Cylinder wall thickness: 10 mm Product-contact material: V4A 1.4571 (AISI316) Condition: used Cylindrical height: 1,500 mm Last application: pharmaceutical TANK Max. permissible operating temperature: 138 °C Gbjdpfx Aboxqadzedjg HEATING/COOLING JACKET Bottom temperature control: double jacket INSULATION Insulating jacket: hermetically welded Insulation material: mineral wool Insulating jacket material: stainless steel Insulation thickness: 70 mm EQUIPMENT Manhole / dome: in upper head (DN 500) Outlet: available MATERIAL SPECIFICATION Temperature control system material: V2A 1.4301 (AISI304) AGITATOR 1 Agitator manufacturer: PRG Voltage: 400 volts TECHNICAL DATA / DIMENSIONS Bottom wall thickness: 7 mm Agitator arrangement: offset in upper head Agitator equipment: additional 1 propeller on agitator shaft Top head wall thickness: 5.7 mm

Condition: excellent (used), Bosch U-HD 350 Kg/h. Bj2015 Weishaupt burner gas or oil possible Gbjdpfxjm Rhdye Abdjg

Condition: good (used), functionality: fully functional, For sale is a copy milling machine from Makre Franz Kuhlmann KG, GM 1/2 series. The machine is fully functional and ready for immediate use. Technical specifications: X-axis (longitudinal travel): 330 mm Y-axis (transverse travel): 200 mm Z-axis (vertical travel): 280 mm Template table: 500 x 400 mm Spindle speeds: 4,200 – 20,000 rpm Spindle mount: Collet bores up to 8 mm possible Motor power: 0.5 kW Dimensions: approx. 1145 x 1020 x 1620 mm (L x W x H) Weight: 430 kg Transport and loading can be arranged throughout Europe upon request for an additional charge. Prices exclude VAT. Viewings are available by appointment. Contact us; our team will be happy to help you. Trade-ins or exchanges are possible! Machine Purchase/Sale PURCHASE/SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Gedpewal Dhsfx Abdsbg Do you need a high-quality, yet affordable metalworking machine for your production? Or do you want to sell yours? For more information or to contact us, visit our website.

Year of construction: 2020, condition: new, Title Strassburger Filter SF400oDEC/30S Integra – Stainless Steel Plate and Frame Filter Press – Year 2020 – NEW / Unused Short Description For sale: unused, factory-sealed plate and frame filter presses from the renowned German manufacturer Strassburger Filter GmbH + Co. KG. The units are in brand-new condition, have never been commissioned, and remain in their original packaging from the factory. Manufacturer Strassburger Filter GmbH + Co. KG (Germany) Model / Type SF400oDEC/30S, Integra format Gbjdex Ihufopfx Abdjg Machine designation: FI6722 – FP PRE 1 Year of Manufacture 2020 Serial Number Among others: 032003303920 (additional serial numbers available) CE Marking Yes Condition Brand new / unused Factory-sealed Never installed, never used for production Stored in warehouse Quantity Available 4 identical units available New Price Original price €94,000 per unit (Total value for 4 machines: €376,000) Design / Material All stainless steel Plate and frame filter press Gasketed plates Pharma / biotech specification Hydraulic closure incl. hydraulic unit CE-compliant Technical Data Plate format: 425 × 400 mm Number of filter chambers: 28 Total filter area: approx. 3.4 m² Total volume: approx. 13.6 liters (100%) Max. operating pressure: 6 bar Max. operating temperature: 95 °C CIP / SIP capable (cleaning up to 121 °C) Dimensions & Weight Length: approx. 1,649 mm Width: approx. 600 mm Height: approx. 1,145 mm Weight (filter frame): approx. 480 kg Weight (plate pack): approx. 120 kg Plate Pack 14 filter plates 13 filter frames 1 end frame 1 partition plate 28 filter layers per setup Hydraulics & Drive Hydraulic closure Hydraulic power unit included Motor power: 1.5 kW Electrical connection: 400 V / 50 Hz Solenoid voltage: 24 V DC Compressed air requirement: 3.0 bar Connections Product inlets and outlets: DN25 Vent / drain: DN15 Connections according to DIN 11864-2 Drip tray included Areas of Application Pharmaceutical production Biotechnology Chemical industry Pre-filtration Precipitation and clarification processes Location Germany Inspection by appointment Immediately available

Condition: good (used), Year of construction: 2024, Welding turntable KT 300 Load horizontal 300 KG, tilted 150 KG Power consumption 220V, 50 Hz table diameter 450mm height 500mm Tilt range stepless via crank gear motor 0 - 90°. speed 0,3 - 2,5 rpm Incl. foot remote control Surcharge: Gjdpebvk I Esfx Abdobg Quick release - jaw chuck diameter 300mm, 450.-€

Year of construction: 2002, condition: refurbished (used), Saacke hob sharpening machine model HG I Largest outside diameter: 300 mm Largest vertical distance: 300 mm Grinding table X axis Center height: 200 mm Distance between centers: 700 mm X-Travel : 600 mm max. Feed Rate : 10 m/min Grinding head Y-axis Y Travel Height: 200 mm maximum Feed Rate: 5 m/min Grinding head Z axis Cross travel: 200 mm max. Feed Rate: 10 m/min Workhead carrier A-axis Workhead Spindle: ISO 50 Indexing accuracy: 10 sec Grinding spindle liquid-cooled motor spindle diameter: 170 mm Wheeö Adapter with Automatic Clamping HSK E50 Spindle speed infinitely variable, rpm: 2,000-10,000 rpm Grinding wheel diameter: 200 mm Tailstock Barrel Hydraulic: 200 Gbodpjltlayofx Abdjg Driver Output in kW Grinding spindle : 10 kW X-axis: 1.4 kW Y-axis: 1.4 kW Z-axis: 1.4 kW A-axis: 2.0 kW High-pressure flushing for permanent cleaning of the grinding wheel during the grinding process Space requirement (without cooling container): 4m x 3.8m Weight: approx. 4500 kg Total Power Rating: 21 kW

Condition: new, Year of construction: 2024, load capacity: 300 kg, Equipment: foot remote control, rotational speed infinitely variable, Protec KT 300 H welding turntable, 170/400 special version Horizontal load 300 kg, tilted 150 kg Power consumption 220 V, 50 Hz Table diameter 450mm Hollow shaft diameter 170mm Table height 500mm Welding current transmission 400 A Quick-action chuck diameter 300mm, surcharge 550.-€ Quick-action chuck diameter 400mm, surcharge 750.-€ Crank gear motor 0 - 90° stepless adjustment Gjdpfx Abevbrqxodjbg Infinitely variable speed 0.01 to approx. 5 rpm. incl. foot remote control Digital display with welding time limiter (if required)

Condition: new, Year of construction: 2025, functionality: fully functional, load capacity: 1,000 kg, table load: 1,000 kg, 3-axis turning and tilting positioner with 1000 kg load capacity, clamping plate diameter 0.65 meters Height adjustment 1000 - 1500 mm Suitable for welding, assembly, processing, etc. With its stable and robust construction, flexible positioning via three axes including overhead, and user-friendly operation, it facilitates welding, assembly, and handling of large workpieces. Optimal positioning of the workpiece improves welding quality and allows higher specified loads in any position. Thanks to the endless rotation of the two rotary axes and additional height adjustment, all workpiece positions (including overhead) are possible. Gbsdpfjxbh Dqjx Abdsg Turntable speed infinitely adjustable from 0.1 to 1.0 rpm. With wireless remote control Rotation range 360° infinite Swivel range 360° infinite Lift: 1000 - 1500 mm Arm outreach radius: 1 meter

Condition: like new (used), functionality: fully functional, load capacity: 6,500 kg, Load capacity 6500 kg Please note: Arm diameter adjustable from 1880 mm to 4550 mm (swivel-out) Space-saving and continuously adjustable, the extension arms can be locked in place Speed continuously adjustable from 0.001 to 5 rpm Motor power 3 kW Torque 15000 Nm Height 800 mm Gbjdpfx Aewd Twqobdsg Maximum current transmission 2000 A Weight 4700 kg with hand and double-foot remote control CE certificate, declaration of conformity, documentation, circuit diagram with original 2016 quotation invoice Current new price approx. €28,000