Used Deep Hole Drill for sale (8,570)

Condition: excellent (used), 10 x Deep-hole drill bits, manufacturer Botek 3 pieces, 6.5 x 320 mm 2 pieces, 10.2 x 190 mm 3 pieces, 10.4 x 250 mm 1 piece, 11 x 350 mm Rcedehl Awdjpfx Alcsf 1 piece, 11 x 270 mm Weight: 1.5 kg

Condition: good (used), drilling depth: 1,500 mm, feed length X-axis: 2,000 mm, feed length Y-axis: 1,300 mm, feed length Z-axis: 1,500 mm, Manufacturer: TBT deep drilling technology Type: BW 250-S Control: SIEMENS 840D Year of manufacture: 2007 Drilling, Milling, Tapping for heat exchanger bases and plates Swivable A Axis + 25 to - 15 Degrees Filtration and Coolant system 1000 L Cip conveyor 2000 x 1200 height out put Milling tool changer Tower Station 20 positions Capacity ELB Drilling 3 - 35 mm Capacity Milling 250 ccm/Min Feed rates all axis 15,000 mm/Min X-Y-W-Z Cutting hours approx. 15,000 Large tooling package Specifications Metric US Standard Max. Drill Ø steel 40 mm Rcjdpfov A Uw Djx Alcof Drilling depth 1500 mm X - axis 2000 mm Y - Axis 1300 mm Z-axis 1500 mm W-axis 750 mm Table load 15000 Table dimensions / L x W or ø 1600 x 1200 mm Spindle mount HSK 63 Mk Spindle power 11 kW Speed 8000 Rpm Dimensions (estimate) Length 7200 mm Width 7800 mm Height 4250 mm Weight 23000 kg Please note: The information on this page is believed to be accurate and is provided by us and, where possible, from the manufacturer. The information is provided in good faith but accuracy cannot be guaranteed. Accordingly, it will not constitute a representation or contractual terms. We recommend that you check all important details.

Condition: refurbished (used), Year of construction: 2019, TECHNICAL DETAILS Drilling depth: 1,400 mm Full drilling range: 40 mm Spindle speed: 670 - 3,560 rpm Center height over bed: 380 mm Center height over floor: 1,400 mm Table length: 1,200 mm Table width: 1,200 mm Cross table travel: 2 x 400 mm Center height over table: 250 – 600 mm Z-axis Feed rate: 0-7,000 mm/min W-axis - 400 mm Rcodpfew Ekfujx Alcof Feed rate: 0-7,000 mm/min X-axis - 800 mm Feed rate: 0-2,000 mm/min Y-axis - 350 mm Feed rate: 0-3,000 mm/min Rapid traverse speed: 3.5 m/min Motor nominal speed: 8,000 rpm Motor rated output: 18.5 kW MACHINE DETAILS Operating voltage: 380 V Frequency: 50 Hz Connected load: 40 kW Total length: 6,500 mm Total width: 3,500 mm Total height: 2,900 mm Weight: 8 t EQUIPMENT Manufacturer: Siemens Sinumerik 840 Dsl Including 1,700 l coolant system 20 solid carbide single-lip drills, diameters 6 mm to 20 mm, lengths 1,200 mm to 1,750 mm

Condition: good (used), Year of construction: 1997, TBT ML 200-2-850 deep hole drilling machine TECHNICAL DATA Type: M200-2-850 Number of spindles: 2 Drill carriage stroke: 850 mm Drilling method: Single-lip drilling Drilling depth with: Submersible spindle: 120 mm Sealing housing: 400 mm Sealing housing with bezel: 350 mm Spindle drive Power: 2 / 3.5 / 1.5 kW Voltage: 140 / 350 / 350 V Speed: 14 / 11 / 6 / A Feed - own drive Feed speed: 20 - 500 mm/min Rapid traverse speed NC operation: 12 m/min Feed force: 1.5 kN Motor power: 2.2 Nm at 3000 rpm Clamping tailstock Motor power: 0.75 kW at 1000 rpm Spindle speed: 500 rpm Stroke max: 200 mm Main dimensions Redpfx Alsvca Rcececf L x W x H: 4600 x 2500 x 2100 mm Transport weight: 3200 kg Control: Sinumerik 805 M No liability is assumed for the correctness, completeness and up-to-dateness of the information provided

Condition: ready for operation (used), -Drill diameter: 5~25 mm -Drilling depth: 1000 mm -Tailstock -Tank -Pump Rcsdpfodgpltox Alcjf -Filter

Condition: excellent (used), Year of construction: 2007, • Maximum possible drilling depth: 1200 mm • Maximum hole diameter: 32 mm • Minimum drilling diameter: 6 mm • Longitudinal travel (X-axis) table: 1800 mm • Cross travel (Z-axis) column: 1700 mm • Cross travel (W-axis) drilling head: 1150 mm • Vertical travel (Y-axis) drilling head: 1200 mm • Clamping surface NC table: 1500 x 1000 mm • Maximum table load: 10 t • Rotary axis (B-axis) rotary table: 360° • Rotary axis (A-axis) drilling head: -25°/+15° • Feed rate: 1-15 m/min (Y-axis: 1-10 m/min) • Rapid traverse speed in all axes: 15 m/min (Y-axis: 10 m/min) • Maximum spindle speed: 6000 rpm • Minimum spindle speed: 60 rpm • Tool holder: SK 40 • Tool clamping: OTT • Rated power main drive (100% ED, S1/40% ED, S6): 9/13 kW • Coolant tank capacity: 1000 l • Maximum coolant pressure: 100 bar • Low-pressure external and high-pressure internal coolant supply • Power supply: 3x 400 V; 50 Hz • Required installation space (L x W x H): 6550 x 5350 x 4130 mm • Machine weight: 12,000 kg Deep Hole Drilling Machine Equipment • CNC control: HEIDENHAIN iTNC 530 • Interpolated rotary table with minimal backlash, dimensions 1500 x 1000 mm • Swiveling drilling head +15°/-25° • Shank drilling head • Handwheel HR520 • Fixed supports (2 units) • Tool magazine: ELB tools: 12 pcs (max. diameter: 32 mm / max. length: 1550 mm) Standard tools: 12 pcs (max. diameter: 140 mm / max. length: 400 mm) • Direct measurement and positioning system in X, Y, and Z axes • Collision monitoring system for supports and drill sleeves • Oil cooler • Coolant flow control system Rcjdpfexyf E Nex Alcof • Adjustable coolant nozzles • Cooling unit for electrical cabinet • Enclosed upper cover (roof) • Drip tray for machine and tank facility (tray height 30 mm) • Extraction system • Infrared touch probe • Drilling depth extension 1200 mm (retrofit) • Chip conveyor

Condition: reconditioned (used), -Drill diameter: 5~25 mm -Drilling depth: 1500 mm -Tailstock -Tank -Pump -Filter Rcsdpfshuil Rsx Alcjf

Condition: good (used), We offer contract deep-hole drilling work. From a diameter of 0.5 to 400 mm and up to a drilling depth of 12,000 mm, everything is possible! Please contact us and we will be happy to prepare a quotation for you. Please let us know the quantity, the material, the drilling diameter and the drilling depth. Rodpfert T U Eox Alcscf

Condition: excellent (used), Year of construction: 2009, drilling depth: 350 mm, workpiece weight (max.): 1,600 kg, table load: 1,600 kg, Deep hole drilling machine Mollart - LD8 - 150 Pellet Die Number of Spindles 8 Gun Drilling Diameter Range 1.5mm-10mm (Per Spindle) Maximum Drilling Depth 150mm Drill Spindle Stroke 350mm Pellet Die Diameter 500mm-1550mm B-Axis Accuracy +/- 6 Arc Seconds Y-Axis Vertical Travel 400mm Gun Drill Speed Range 0-14,000 RPM Max. drill Ø steel 1.5 - 10 mm Drilling depth 350 mm Table load 1600 Speeds / ranges 14000 Rpm Dimensions (Estimate) Length 4500 mm Width 4500 mm Rjdpfeyilgdsx Alcjcf Height 2300 mm Weight 12000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2018, drilling depth: 1,250 mm, total length: 8,100 mm, total width: 6,300 mm, total height: 4,300 mm, workpiece weight (max.): 7,000 kg, overall weight: 31,000 kg, travel distance X-axis: 1,600 mm, travel distance Y-axis: 1,250 mm, travel distance Z-axis: 1,100 mm, spindle speed (max.): 6,000 rpm, drill diameter: 36 mm, 4 side complete machining Swivel drilling and milling unit DCM Dynamic Collison Monitoring CAM model QCK (Quick Check Kinematics) Transfer bore cycle (380-382) 90 Bar IKZ Coolant system Extra ATC Tower 24 position (4 x 6) HSK 63 Double ballscrew construction Clear tank 1650 L and Waste tank 1300 L Chip conveyor Max. drill Ø steel: 36mm Drilling depth: 1250mm Rsdpfxovn Sv Uj Alcocf X - Travel: 1600mm Y - Travel: 1250mm Z - Travel: 1100mm W - Travel: 1600mm Table load: 7000 Table size L x W / or ø:1500 x 1100mm Spindle taper: HSK-63Mk Power on spindle: 23kW Speeds/ranges: 6000rpm Length: 8100mm Width: 6300mm Height: 4300mm Weight: 31000kg

Condition: good (used), Year of construction: 2004, IXION AUERBACH IA2 TLF-1200.4 Year of manufacture: 2004 Factory overhauled: 2023 CNC control: HEIDENHAIN 430M Travel X (table, longitudinal): 1,200 mm Travel Y (deep hole drilling-milling unit, vertical): 1,200 mm Travel Z (turret, horizontal): 700 mm Travel W (deep hole drilling-milling unit, horizontal): 1,200 mm A-axis (swivel of deep hole drilling-milling unit): +25°/-15° B-axis (NC rotary table): 360° NC rotary table with 5 T-slots: 1,000 x 1,000 mm Max. workpiece weight: 7,000 kg Rated drive power (S1 / S6): 12 / 18.5 kW Rodpfsydmuuox Alcecf Torque: 115 Nm Speed range: 60 - 6,000 rpm Max. drilling depth (in one pass): 1,200 mm (with 2 traveling steady rests) High-pressure coolant system for deep hole drilling oil: 100 bar & 42 l/min Tool changer for 24 tools With spindle air blast Max. tool length: 300 mm Max. tool weight: 3.5 kg Tool diameter Without adjacent free space: max. 90.0 mm With adjacent free space: max. 160.0 mm Equipment inside work area: - Fully enclosed working area with roof - Oil mist extraction - Chip conveyor Required floor space: 5,150 x 5,350 x 4,020 mm

Condition: excellent (used), Heidenrich & Harbeck B3 SB Deep Hole Borer 10,000mm Capacity, 4 off Steady Rests 2 off Boring Bar Dampers Swarf Tray & Baskets Tooling, Rcodew U Uhkspfx Alcjf Counter Rotation

Condition: like new (used), Ryazan Model PT295106 Deep Hole Borer x 4000mm Manufacturer Ryazan Model PT295106 Year 1985 Condition Used Rcsdpfxoxzp Rlo Alcof Stock Number 2850 Centre Height 550mm Solid Boring Capacity 200mm Max Boring Length 4000mm Headstock Hollow spindle 500mm Headstock Spindle speeds 16-250 rpm Headstock drive 50/75kw Max boring length in front of headstock 3500mm Max boring length if using the 500mm hollow spindle 4000mm

Year of construction: 2013, condition: used, controller manufacturer: Siemens, controller model: 840Dsl, _____ Description: Year of manuf. : 2013 In general: Drilling-ø (max.):3,5 mm Drilling depth (max.):200 mm Deep drilling module: Technology:Drillingspindle Speed (max.):10.000 rpm Power:3,5 kW Taper:HSK-A40 Equipment/Accessory: Chipmanagement:Chip tray Coolingmanagement:Internal cooling unit with Filter and High-pressure, 140 bar Workpiececlamping:Collet chuck, SMW Autoblok KSZ-MB-040-Z140 Rcodpfsx E Ingox Alcjf Oilmistseparation:Electrostatic extraction, LTA AC 500 Further Accessory:Misc. Single lip driller

Condition: refurbished (used), Year of construction: 2000, functionality: fully functional, drilling depth: 600 mm, rotational speed (max.): 6,000 rpm, center height: 250 mm, controller model: SIEMENS Sinumerik 840 D, workpiece diameter (max.): 25 mm, No reserve price – guaranteed sale to the highest bidder! The machine has been completely overhauled! TECHNICAL DETAILS Working depth: 600 mm Working diameter: 4 – 25 mm Number of spindles: 2 Centre height: 250 mm Centre distance: 203.2 mm Speed range: 1,000 – 6,000 rpm Redpfoxpvbtjx Alcocf Feed rate: 0 – 300 mm/min Rapid traverse: 6,000 mm/min MACHINE DETAILS Control system: SIEMENS Sinumerik 840 D (Retrofit) Drilling system: Single-lip deep hole drilling Main drive: 2 x 5.5 kW EQUIPMENT - Single functions for machine setup - Semi-automatic operation for manual loading - Robust spindle carriage - Machine monitoring with spindle speed display - Table plate in special cast design - Safety guard with sliding door - Machine bed with hardened and ground linear guides - Internal coolant supply through drilling spindle - Electrical equipment according to IEC standards - Separate control cabinet with safety devices - Control panel in working area

Year of construction: 1985, condition: used, Drilling process: single-lip gundrilling, operating method: rotating tool, number of working spindles: 1, nominal drilling depth: approx. 750mm, drilling range for solid drilling in steel: approx. 30mm, drilling range for counterboring in steel: approx. 40mm, spindle drive: 11kW, max. spindle speed range I: 1800rpm, max. spindle speed range II: 5700rpm, max. feed rate range I: 320mm/min, max. feed rate range II: 160mm/min, rapid traverse: 3.5m/min, clamping table X/Y: 420mm/1280mm, cross-slide table manually operated, max. transverse travel: 400mm, table clamping surface X/Y: 600mm/600mm, high-pressure coolant system for deep-hole drilling oil with 1000l coolant tank, flow rate: approx. 2-94l/min, max. pressure at max. flow rate: 45bar, pump power: 11kW, separate control cabinet. The machine underwent an extensive partial overhaul in 2018, during which the machine was disassembled and cleaned, all guideways and support surfaces were ground and partially scraped, motors were inspected and fitted with new bearings, the drilling spindle was fitted with new bearings, the ball screw incl. nut was replaced, the pump motor was overhauled, the wiper set was replaced, and the machine was repainted and all functions were checked and rectified. Including extensive accessories. Documentation available. Inspection possible by arrangement. Rodpfx Alszu Szyececf

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, Facom foratrice Through-hole drill f-v3r-2l-3f+2tagr1 used 2015 Brand: Facom foratrice Model: Through-hole drill f-v3r-2l-3f+2tagr1 Description: Through-feed drill F-V3R-2L-3F+2TAGR1 All heads and saws are screw-adjustable with mechanical indicators. Drilling depth is controlled electronically. Minimum workpiece length: 300-350 mm Maximum: 2000 mm Automatic feeder Bsbtt Sov U Uw Ujx Nteda Double-sided cutting with angle adjustment Double-sided drilling with angle setting 3 drill heads top + 2 wheels + 2 rear All heads have angle adjustment Rodpfx Asx Rd Eljlcscf Electronic position markers I can send a video via WhatsApp The machine is operational and connected; you can test it 2015 Year: 2015

Condition: used, Year of construction: 2024, DOWEL HOLE DRILLING MACHINE GANNOMAT "DB 21400V, 3Ph, 50Hz / 1.5 kW, complete in standard design with: - Fully automatic electronic control with pulse operation via foot valve for clamping-drilling-releasing, electric intermittent operation. - Automatic retraction of the drilling unit after reaching the set drilling depth. - Automatic extension of the drilling hole depth when drilling on the end face. This eliminates the need to adjust the drilling hole depth from flat-face to end-face drilling (+10 mm, e.g. for a dowel length of 35 mm, drilling depth on the flat face 14 mm and drilling depth on the end face 24 mm). - 1 drilling bar with 21 spindles, pitch 32 mm, motor 1.5 kW (drilling feed 0-70 mm), incl. 21 quick-change chucks (Ganner system) for easy changing of the drill bits. - Easy pivoting of the drilling unit from 0° to 90°, supported by gas cylinders. - 1 clamping support movable in the Y-axis with 3 pneumatic clamping cylinders, for workpiece height up to max. 80 mm. Ideal stop system consisting of: - 1 stop rail 1800 mm for drilling shelves (aluminum profile 40x40 mm) with 3 stop blocks, with quick-change system, easily interchangeable from right to left stop side for drilling shelves in carcass structures in mirrored fashion, also suitable for row drilling in the 32 system. - Side stops and position settings, as well as the position of the drilling height above the support table, are adjusted by means of mechanical digital counters. - Side stops can be easily pivoted away, for the shortest possible conversion from carcass to frame and row drilling. - Clamping arms for the clamping support designed for row drilling positions up to max. 300 mm. - Ideal three-stage tool system. - 1 set of drill bits for dowels: - 5 carbide dowel drill bits, Ø 8x77 mm, right-hand - 4 carbide dowel drill bits, Ø 8x77 mm, left-hand Basic machine DOWEL HOLE DRILLING MACHINE GANNOMAT "DB 21400V, 3Ph, 50Hz / 1.5 kW, complete in standard design with: - Fully automatic electronic control with pulse operation via foot valve for clamping-drilling-releasing, electric intermittent operation. - Automatic retraction of the drilling unit after reaching the set drilling depth. - Automatic extension of the drilling hole depth when drilling on the end face. This eliminates the need to adjust the drilling hole depth from flat-face to end-face drilling (+10 mm, e.g. for a dowel length of 35 mm, drilling depth on the flat face 14 mm and drilling depth on the end face 24 mm). - 1 drilling bar with 21 spindles, pitch 32 mm, motor 1.5 kW (drilling feed 0-70 mm), incl. 21 quick-change chucks (Ganner system) for easy changing of the drill bits. - Easy pivoting of the drilling unit from 0° to 90°, supported by gas cylinders. - 1 clamping support movable in the Y-axis with 3 pneumatic clamping cylinders, for workpiece height up to max. 80 mm. - Ideal stop system consisting of: - 1 stop rail 1800 mm for drilling shelves (aluminum profile 40x40 mm) with 3 stop blocks, with quick-change system, easily interchangeable from right to left stop side for drilling shelves in carcass structures in mirrored fashion, also suitable for row drilling in the 32 system. - Side stops and position settings, as well as the position of the drilling height above the support table, are adjusted by means of mechanical digital counters. - Side stops can be easily pivoted away, for the shortest possible conversion from carcass to frame and row drilling. - Clamping arms for the clamping support des Redjxnlflopfx Alcscf

Condition: used, Scheer DB 5 dowel hole drilling machine for the precise and rapid drilling of dowel holes (horizontal and vertical) in solid timber and board materials. The machine is ideal for mass production in furniture manufacturing as well as for precise joints in interior fit-out work. Includes a comprehensive range of dowel bits. Technical data: - Drilling spindles: 21 - Pitch: 32 mm Rjdpfx Asztvx Tjlcocf - Passage width: max. 1,000 mm - Swivel mechanism: pneumatic - Fax: , Mobile: , Machine No. 208695, Jan 2011, Cost price €1,000 - D-89440 Lutzingen, Tel. , Fax: , April 2015, purchase price €500

Condition: good (used), Tools , drills will come without tool cabinet . Rodpfx Alezd D N Iocjcf Tool trolley with toolholders will come.

Condition: used, Year of construction: 1985, Used Machine Year of Manufacture: 1985 Features and Technical Specifications: - For horizontal and vertical structural drilling - For vertical row drilling in a 32 mm grid Redpfezk N Dwox Alcocf - Vertical drilling unit with dual-spindle drill heads, freely positionable on an indexing shaft - 1.5 kW motor at 1,400 rpm - 1.5 kW motor with 2,800 rpm - Drill heads with pneumatic stroke - Pneumatic workpiece clamps - Passage width approx. 850 mm - Includes various stops and drill bits Availability: at short notice Location: DE-63934 Röllbach

Year of construction: 1980, condition: ready for operation (used), Ayen Type DB 1000 K 23 Rcsdpfx Alepgkqpecof Year of manufacture 1980 GS-tested number of spindles 23 pieces number of drilling beams 1 spindle distance / grid 32 mm drilling from above swiveling pneumatic Hole line drilling device

Condition: used, Year of construction: 2014, Used Machine Year of manufacture: 2014 Condition: The machine has been factory-overhauled by Ganner Features and Technical Specifications: Complete standard configuration including: - Support with linear guide consisting of: 1 single-spindle horizontal drilling unit, 0.65 kW motor, 70 mm stroke Tool speed selectable via operator software (3000/5000/8000 rpm) 1 blow-out, gluing, and dowel-driving station for dowels Ø 8 mm, dowel length 25–50 mm - Fully automatic, electronically controlled central lubrication - X-axis NC-controlled, with working length 1300 mm, travel speed max. 105 m/min. - Z-axis manually adjustable via mechanical digital counter, position adjustable via support table 5–40 mm - Dowel drive-in overhang adjustable from 7–20 mm via a mechanical digital counter; drilling depth from 0–35 mm (for drill bit length GL 70 mm) is automatically adjusted with the drive-in overhang - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with a viscosity of 150 to 350 mPas - Glue quantity continuously adjustable via operator software - GLUE/WATER selector switch for flushing the glue system, each with: 1 stainless steel tank for 7.5 kg of glue and 7.5 l of water - Indicator light showing remaining glue levels in the glue tank - 1 left side stop, 1 right side stop, and 1 center stop (all removable) - 4 start buttons for individual processing of 1–4 workpieces - 4 pneumatic 10° angle clamping cylinders for workpiece thicknesses up to 80 mm, workpiece length (Y) min. 70 mm - 1 extraction funnel, connection Ø 80 mm Rsdpozlbrvjfx Alcecf - 1 TCT control unit with: Built-in industrial PC, including Beckhoff TWINCAT soft PLC, operating temperature range 0–50°C, 15-inch capacitive TFT industrial touchscreen, operating system: WINDOWS 7 - Programming via menu-driven user software, drilling distances freely programmable with ABSOLUTE, RELATIVE, or GRID dimensions, automatic workpiece mirroring and operation optimization, 4 work areas assignable to different programs, graphical workpiece display, parametric programming, zero-point offset, programmable worklists, error diagnosis with plain text Optional equipment: - 1 electronic, optical glue monitoring system G.I.C. (Glue Insert Control) for 1 glue nozzle - 1 Z-axis with NC-controlled, dynamic positioning for height adjustment of the drilling and dowel-driving station (programmable from 5–40 mm), travel speed max. 30 mm/sec. - 1 single-spindle vertical drilling unit drilling from the TOP, 0.65 kW, (3000/5000/8000 rpm), position (Y) manually adjustable via a mechanical digital counter from 5–40 mm, drilling depth (Z) max. 30 mm (with drill bit length GL 57 mm), Workpiece thickness (Z) max. 50 mm, workpiece length (Y) min. 130 mm (including drilling depth compensation, e.g., for Häfele Minifix) - 4 vertical 10° angle clamping cylinders with mount - 1 keypad with mount Availability: available shortly Location: DE-63934 Röllbach

Condition: used, Year of construction: 1985, Second-hand machine Year of manufacture: 1985 Universal dowel drilling machine with a swivelling drilling unit with fully automatic control with 2 safety pneumatic clamps Rcedpfx Aljzk N A Tjcef Drilling gearbox, 2.2 kW motor with 21 spindles Spindle pitch 32 mm with integrated oil damping Height adjustment: 80 mm Drilling depth 80 mm Weight: 420 kg Availability: at short notice Location: Röllbach

Condition: used, Year of construction: 1984, Second-hand machine Year of manufacture: 1984 Universal dowel drilling machine with a swivelling drilling unit with fully automatic control with 2 safety pneumatic clamps Drilling gearbox, 2.2 kW motor with 21 spindles Spindle pitch 32 mm Rsdpfozk Nuvsx Alcscf with integrated oil damping Height adjustment: 80 mm Drilling depth 80 mm Dimensions: 140x88x160 Weight: 420 kg Availability: at short notice Location: DE-63934 Röllbach