Used Glue Press for sale (13,246)

Condition: used, Year of construction: 2001, Continuous press Manufacturer: Ligmatech Type: Optimat MDE 10 Year of manufacture: 2001 Technical data Body dimensions - Length: 300 - 2500 mm - Height: 300 - 1300 mm Laedozuzxbjpfx Afwsf - Depth: 120 - 600/800 mm - Pressing forces are generated electrically, both horizontally and vertically, and can be varied independently - Pressing forces are applied vertically via a pressure plate and horizontally via 3 pressure jaws each - Pressing takes place centered and on a zero line on the operator side Positioning of the pressure jaws: - Top pressure jaw with forced guidance on the top press, optionally lowerable via cylinder - Middle pressure jaw freely programmable and motor-driven - Bottom pressure jaw freely programmable and movable via a common drive with the middle pressure jaw Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Lodpfxezuzw De Afwsaf Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Technical data Laedjzuzwwjpfx Afwsf Plate dimensions: 2550 x 1350 mm Hot water heating 6 pressure cylinders Total pressing force: 135 t Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Laodezuzwqepfx Afwof Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Washing and rinsing device for gluing head Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm Lasdpfx Aezuzwkjfwjf - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: Lasdpfx Afszuzv Tjwof min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, Adhesive application machine Manufacturer: Wirth Type: LW 120.5/1300 Year of manufacture: 2009 Technical data - Roller width: 1300 mm - 2 rollers (application + metering) Lsdszuzvyspfx Afweaf Note: The outfeed conveyor shown in the pictures is not included. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Technical data Voltage: 400 V Current: 32 A Frequency: 50 Hz Compressed air: 6 bar Ljdpfx Afozuzvmsweaf Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Short-cycle pressing line Manufacturer: Wemhöner Type: KT-F-1E Year of manufacture: 2001 Technical data Laedpfxjzuzi Ts Afwof - Pressing area: 5,750 mm x 2,200 mm - Operating side: left - Plate dimensions: Length: 2 x 2,600 mm - 2 x 2,620 mm Width: 2,070 mm Thickness: 6 mm - 40 mm - Pressing pressure: approx. 40 kg/cm² Note: Upon request, the complete layout plan of the system can be sent. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 1998, - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Door pressing system Manufacturer: Wild Year of manufacture: 1998 For door dimensions: - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Consisting of the following sections: 1. Continuous door panel gluing with frame assembly station / 2. Pressing line with hardboard facing station Section 1 consists of: - Gantry loading system - Angle transfer with longitudinal and cross saws - Loading and feeding of the longitudinal and transverse frame parts from magazines - Longitudinal cutting station for the longitudinal frame parts - Connecting station of the frame parts with the door panel core. With clamping devices - Conveyor belt angle transfer with shuttle transfer of the door panel cores onto the glued hardboard Section 2 consists of: - Loading of the hardboard - Brush cleaning machine - Hardener application machine from below - Glue application machine from below - Roller conveyor - Angle transfer for the lower hardboard Lodozuzgrepfx Afwsaf - Vacuum reversing device for the upper hardboard - Automatic facing station for hardboard and door panel cores - 2 door presses, each with 2 x 4 pressing stations, arranged parallel to each other - Both presses are loaded at the infeed with 1 shuttle loading basket - Both presses are unloaded at the outfeed with 1 shuttle unloading basket - Angle transfer to the infeed into a hedgehog buffer - Angle transfer at the outfeed of the hedgehog buffer and feeding to the stacking station - One-sided vacuum stacking with protective plate space Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: ready for operation (used), Year of construction: 2009, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 x 65 cm Condition: very good! Video of machine in operation available on request. Lodpozuxv Dofx Afweaf

Condition: ready for operation (used), Year of construction: 2012, Brand: DIXI Ledezuxrxopfx Afwjaf Model: 60 SD Year of manufacture: 2012 Pressing force: 60 tons Voltage: 400 Max. bale weight: 340-500 kg Bale dimensions: approx. 120 x 80 x 80-110 cm Machine weight: 2400 kg Machine dimensions: 190 cm wide x 140 cm deep x 230 cm high Dimensions of the feed opening: 115 cm wide x 80 cm deep x 55 cm high The DIXI 60 SD features simple operation, an automatic start function, and automatic bale ejection. Thanks to its compact, low-profile design, this machine is ideal for spaces with limited height.

Condition: ready for operation (used), Year of construction: 2013, Brand: HSM Type: V-Press 1160 plus Year of manufacture: 2013 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Lodpfxszuxqhs Afwjaf Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm x 65 cm The HSM 1160 V-Press features simple operation, a powerful pressing force, and is energy-efficient. Are you looking for a more compact model? Then take a look at the HSM 860 – ideal for those who want to save space without sacrificing pressing power.

Condition: used, 1x bending knife from a VOEST press brake Length: 4050 mm Weight: approx. 120 kg Ledpey Tbvmofx Afwsaf For further dimensions see pictures.

Condition: new, Year of construction: 2025, sheet thickness - max. 8 mm pressure 200 t chamfer lenght 3200 mm engine output 15 kW return speed 105 mm/min Lodoxf Na Ujpfx Afweaf working feed 9 mm/sec x-travel 600 mm Max. opening height 570 mm control DELEM DA53T GERD WOLFF KANTO 200T CNC Electro-Hydraulic Press Brake CNC axis accuracy 1) Machine sliders (Y1, Y2) – synchronisation precision: The slider movement axes control the bending depth and bending angle. The system consists of the control unit, two glass scales (Y1, Y2) installed on the work table, electro-hydraulic proportional valves and an amplifier. A closed control loop detects and controls the relative position of the slide and table as well as the speed and position of the slide. This ensures the synchronisation of the slide and maintains the bending depth and angle with high precision. Positioning accuracy: ±0.02 mm Repeatability: ±0.02 mm 2) Machine backgauge (X axis): The forward/backward movement of the X-axis controls the dimensions of the sheet metal cut. The stop bar is driven by a servo motor and moves the crossbeam via a ball screw and linear guide. Operation is stable and precise. Positioning accuracy: ±0.10 mm Repeatability: ±0.03 mm 3) Mechanical compensation system (V axis): The pull plate of the mechanical compensation is moved by a motor so that the compensation points are formed in an arc shape. The points perfectly compensate for the elastic deformation of the work table and slide to ensure angular constancy and straightness of the workpiece. Position sensors and CNC control ensure precise regulation.

Condition: used, 1x bending knife from a VOEST press brake Length: 4050 mm Weight: approx. 115 kg For further dimensions see pictures Laodpfxszcgh Ej Afwsf

Condition: used, Year of construction: 1979, pressure 100 t stroke 500 mm table surface area 4000x500 mm weight of the machine ca. 5,7 t HY – S 100 RH MAE hydraulic straightening press, complete with straightening unit Year of manufacture: 1979 Approved in accordance with UVV Stroke: 500 mm Pressure capacity: 100 tonnes Lasdpey Tpr Ajfx Afwsf Table: 4000 x 500 mm Weight: 5700 kg

Condition: used, Year of construction: 1991, pressure / t plate thickness / mm Lajdowgi S Nopfx Afwef no. of strokes / Hub/min Condition: used The punching machine works perfectly. A functional video is available.

Condition: used, pressure 1000 t table length 2110 mm table width 1755 mm stroke 500 mm 18 min work height max. 380 mm 4 Punkt weight of the machine ca. 107,25 t dimensions of the machine ca. / m WILKINS & MITCHELL Trimming press with accessories Pressure force: 1000 t With discharge table and gear component Table area 2110 x 1755 mm Weights Stand: 47.1 T Table: 8.84 T Fumrungen: 1.72 T Ljdpfxsgrnaqj Afwjaf Drive: 26.47 T Compensating cylinder: 1.65 T Motor mount and guard: 2.04 T Pusher: 11.53 T Adjusting screws and bolts: 2.66 T Slide setting: 0.85 T Miscellaneous: 1.02 T Hydraulic ejector: 0.52 T Total weight: 107.25 tons

Condition: excellent (used), Year of construction: 2013, Ref:11118 . 2013 Schmedt Präleg & Präform Casing-in & Pressing Machines. For casing-in a variety of thin to thick books into flexible or hard cases. Special features:- • Programme selection via touch-screen monitor • Very short set-up and strip down times • Auto wash-up of glue rollers after each book Vertical wing action Twin PVA cold glue tanks Ljdpfxjzkgdzo Afwsaf Working in conjunction with:- 2008 Schmedt Präform 2100 Pressing & Joint Forming Machine. For pressing a variety of thin to thick hard cover books immediately after casing-in. Suitable for single or assorted books, pressing & burning in the joint in a single operation. Specification, Praleg 18-60: Block height: 80 – 450 mm Block width: 110 – 450 mm Block thickness: 2 – 80 mm Production rate: approx. 200 – 300 pcs/h Specification, PraForm 2100 Book press with groove cutter. Maximum format: 420 x 520 x 100 mm Power supply: 230 V + compressed air.

Condition: new, Heavy duty splicing press for producing long lengths of timber Simple to use Top and bottom plates press simultaneously Very quick cycle time Lasdpfxepahmhj Afwjf 35 tonne capacity hydraulic pack 7.5Kw motor Pneumatically operated head Maximum timber section 75 x 300mm Two hand control unit Manual eccentric side clamping Optional 2m infeed and outfeed tables

Condition: used, total length: 3,800 mm, total width: 1,650 mm, total height: 2,400 mm, Colour: Green Empty weight: 3.500 kg - Details: - └ Description: The plates need to be repaired - Documentation available: No - CE certificate present: No - Main motor power [kW]: 2.2 - Press drive: Hydraulic - Max. workpiece length [mm]: 3000 - Max. workpiece width [mm]: 1300 - Max. workpiece height [mm]: 450 - Total stroke [mm]: 450 - Number of work zones [pcs]: 1 - Number of levels [pcs]: 1 - Plate material: Steel - Number of cylinders [pcs]: 6 - Cylinder diameter [mm]: 70 - Heating boiler present: Yes - Heating type: Oil heated - Max. temperature [°C]: 120 - Top/bottom separately heated: Yes - Voltage [V]: 400 Laedpfx Ajztc R Aefwjf - Fuse [A]: 32 - Power [kW]: 10.0 - Transport dimensions: 3800mm x 1650mm x 2400mm (l x w x h) - Transport weight [kg]: 3500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: ready for operation (used), Year of construction: 2021, machine/vehicle number: 2.102.061, functionality: fully functional, pressing force: 135 t, stroke length: 210 mm, throat depth: 410 mm, controller model: Cybelec CybTouch 8W, working width: 3,100 mm, TECHNICAL DETAILS Press force: 135 t Max. working width: 3,100 mm Frame spacing: 2,500 mm Overhang: 410 mm Rear gauge depth: 750 mm Max. stroke: 210 mm Number of axes: 4 (Y1, Y2, X, R) MACHINE DETAILS Control system: Cybelec CybTouch 8W Power: 11 kW Tool holder type: European-style Punch holder: Standard Dimensions & Weight Dimensions (L x W x H): 3,720 × 2,300 × 2,750 mm Lsdszrmu Nepfx Afweaf Shipping weight: 7,700 kg Shipping packages: 1 EQUIPMENT Tools CE marking Documentation

Condition: ready for operation (used), functionality: fully functional, pressing force: 70 t, table width: 495 mm, table length: 650 mm, TECHNICAL DETAILS Pressing force: 70 t Ljdpozrmm Sofx Afwjaf Stroke, min.: 10 mm Stroke, max.: 90 mm Table length: 650 mm Table width: 495 mm Column width: 400 mm MACHINE DETAILS Control system: CNC Dimensions & Weight Dimensions (L x W x H): 2,650 x 1,600 x 3,350 mm Dry weight: 9,000 kg Shipping packages: 4 pcs. EQUIPMENT Documentation

Condition: used, Year of construction: 1987, machine/vehicle number: 17080987, input voltage: 380 V, table length: 2,500 mm, total width: 1,300 mm, year of last overhaul: 2024, Equipment: documentation/manual, We are offering this used Italpresse BN-25-F veneer press, manufactured in 1987. It has been inspected and overhauled in 2024 and is SKH certified. It features two-hand operation and an emergency stop. If you have any questions or would like more information, please feel free to send us a message or call us. Lajdpfxezu A Azj Afwef