Used Hank for sale (3,491)

Condition: good (used), Wilo DL-E 100/145-11/2-S1 Glanded double pump Glanded double pump in inline design for pipe installation or foundation installation with integrated frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v). Design Bodpfx Adewbqrts Ajlr Electronically controlled glanded double pump in inline design with flange connection and automatic power adjustment Application Pumping of heating water (in accordance with VDI 2035), cold water and water-glycol mixtures without abrasive substances in heating, cold water and cooling systems. Equipment/function Operating modes Δp-c for constant differential pressure Δp-v for variable differential pressure PID control Actuator mode (n=constant) Manual operating level Setting the differential pressure setpoint Setting the speed (manual control mode) Setting the operating mode Setting pump ON/OFF Configuration of all operating parameters Error acknowledgement External control functions “Priority Off” control input “External pump replacement” control input (only effective for dual pump operation) Analog input 0-10 V, 0-20 mA for actuator operation (DDC) and remote setpoint adjustment Analog input 2-10 V, 4-20 mA for actuator operation (DDC) and remote setpoint adjustment Analog input 0-10 V for actual value signal of the pressure sensor Analog input 2-10 V, 0-20 mA, 4-20 mA for actual value signal of the pressure sensor Message and display functions Collective fault message SSM Collective operation message SBM Data exchange Infrared interface for wireless data exchange with IR monitor/IR stick Slot for Wilo IF modules (Modbus, BACnet, CAN, PLR, LON) for connection to the building automation system Safety functions Full motor protection with integrated tripping electronics Access lock Double pump management (double pump or 2 x single pump) 2 x single pump) Main/standby mode (automatic fault switchover) Main/standby mode Pump replacement after 24 hours Add-on mode Add-on mode (efficiency-optimized peak load switch-on and switch-off) Your benefits Energy saving thanks to integrated electronic power adjustment Simple operation thanks to green button technology and display Various operating modes: Main/standby mode and parallel operation Configurable fault behavior tailored to heating and air conditioning applications Integrated full motor protection (KLF) with tripping electronics Drive Mains connection 3~380 V, 50/60 Hz 3~400 V, 50/60 Hz 3~440 V, 50/60 Hz Motor efficiency class: IE4 Power consumption P1 max: 13000 W Nominal motor power P2: 11 kW Current (max) Imax: 21 A Speed max. nmax: 2970 1/min Interference emission EN 61800-3 Interference immunity EN 61800-3 Insulation class: F Protection class motor: IP55 Motor protection: KLF integrated Installation dimensions Installation length L0 500 mm Suction-side pipe connection DNs DN 100 Pressure-side pipe connection DNd DN 100 RRP: € 29,006.25 Find more new and used items in our store! International shipping costs on request!

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, turning length: 1,000 mm, turning diameter: 340 mm, Machine type: CNC lathe Manufacturer: Okuma Type: LU15-M Year of manufacture: 2000 Control: OSP-U100L Country of origin: Japan Delivery time: from stock Long turning length - 1000 mm Towable tailstock - automatic G152 Partial hollow clamping device The lathe is in very good condition. The basic and additional equipment enables this used machine to process long turning lengths of up to 1000 mm. Effective production is also possible thanks to the towable tailstock - automatic, the tool breakage / wear control, the partial hollow clamping device, the K pump and the dialog programming (IGF). An optimal machine for economical and reliable production. The machine is user-friendly and can be integrated into production immediately. Machine equipment Spindle motor VAC built 22/15 kW Long turning length – 1000 mm Towable tailstock – automatic G152 3-jaw chuck Forkardt, diameter 250 mm Steady preparation B-turret Partial hollow clamping device Dialog-IGF K-pump Tool breakage/wear control Chip conveyor Technical data Max. turning diameter: 340 mm Max. turning length: 1000 mm Travel X-axis: upper 260 mm (170+90); lower 140 mm (90+50) Travel Z-axis: upper 1,040 mm; lower 1.015 mm C-axis travel: 360° Spindle – number of travel steps: 2 – automatic Bore diameter: 62 mm A-turret (upper): 12 tools, all M-tool compatible, VDI 40 B-turret (lower): 8 tools, VDI 40 Rotating tool speed: 45~4500 min -1 Rapid feed: m/min X:15, Z:20, C:200 min -1 Tailstock quill diameter: 90 mm Tailstock quill stroke: approx. 100-120 mm Machine dimensions without accessories LxW: approx. 4800 x 2200 mm Machine height: approx. 2030 mm Bljdjx Afz Ajpfx Ad Aer Weight: approx. 6900 kg Optional Transport organization and implementation Machine delivery and installation Machine commissioning and production-ready handover

Condition: excellent (used), Here we offer a used Datona mobile sandblasting unit. Datona mobile sandblasting unit DUO - 74 liters SKU DT-55212 Advantages and disadvantages: 2.5 m long hose for a long reach Easy to switch between blasting agents thanks to the mixing valve When using soda, the surface of the workpiece is not damaged Description: This mobile sandblasting machine is used for removing paint and rust. Thanks to the two boilers, you can choose from two different blasting media. The mobile sandblasting unit works with a pressure of 4 to 8 bar and requires a compressor with a suction capacity of at least 350 l/min. Double boiler: If blasting with soda or calcium carbonate does not achieve the desired result, simply try a different blasting agent. For a more effective effect, it is also possible to use both blasting agents at the same time. With the sandblaster, you have a practical machine in your home. With the help of the special mixing valve, you can use soda to easily and gently remove paint from steel, stainless steel, chrome, aluminum or polyester. A major advantage of blasting with fine soda is that the surface of the object to be of the object to be blasted is not damaged. You don't even have to remove rubber seals, chrome parts or glass. This saves a lot of time! The mobile sandblasting unit can be used both in the workshop as well as on site. Attention: The one boiler is only suitable for soda and calcium carbonate!!! ✓ Duo sandblasting unit ✓ 74 liter boiler capacity ✓ Air consumption is around 350 l/min Technical data: SKU DT-55212 Weight 33 kg Suitable blasting material Aluminum silicate Dato-Blast calcium carbonate soda Blodpfx Adoqcuvwj Aor Blasting cabinet connection 1/4" Max. Pressure 2 - 6 bar Minimum air consumption 350 l/min Min. compressor tank capacity 100 liters Type: DT-55212 Condition: gebraucht / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: as good as new (ex-display), Year of construction: 2024, Automatische langssnijzaag Raimann FlexiRip “Jrionline” Bodeu Sg Anspfx Ad Ajlr Zaag lengte : 6200 mm Maximale zaaghoogte afhankelijk van de diameter van het zaagblad, variërend van 85 tot 210 mm. Alleen gebruikt als demo, praktisch als nieuw, met slechts 34 draaiuren.

Condition: new, Introducing the Servomill® KB 1500, a robust Conventional Vertical Milling Machine from KNUTH that excels in the milling machine category. Designed with servo-conventional feed technology, this versatile machine features a heavy-duty frame, wide guideways, and high drive power for superior cutting performance. Its universal milling head swivels in two planes, allowing you to achieve precise positioning at any angle. The integrated electronics facilitate easier and more precise conventional milling, ensuring an efficient workflow without necessitating programming. The Servomill® is perfect for substantial workpieces thanks to its extensive table dimensions of 2100 x 500 mm and high maximum workpiece weight. With enhanced features such as electronic handwheels, limit stops, and an automatic coolant system, users can enjoy increased reliability and performance. Whether you're in plant construction or machine building, this machine will meet your heavy-duty machining demands. Explore the extensive accessories available to maximize your milling capabilities. For further information or to order this reliable machine, please request a quote today. Blsdpfxjwt Dvio Ad Asr

Year of construction: 2015, condition: used, max. dia. of grinding wheel 150 mm turning speeds 2850 U/min total power requirement 0,45 kW dimensions 465 x 316 x 302 mm weight 10,7 kg NEW PRICE: ~ 200.00 EURO Description - Double grinding machines from OPTIMUM - a quality product for trade and Bledpewp S U Ejfx Ad Aer industry - Heavy-duty, durable industrial design with maintenance-free motor for continuous use - Extruded aluminum housing - Long service life and smooth running thanks to balanced rotor with high-quality ball bearings - Spark guard on each grinding wheel reduces flying sparks - Stable, adjustable workpiece support - Viewing windows made of shatterproof material - Vibration-damping rubber feet - Two universal corundum grinding wheels

Condition: new, Cantilever racking to your desired dimensions! Ideal for storing your long goods. Easy access to your products thanks to configurations that can be used on one or both sides. Expandable system that allows you to add elements as your requirements evolve. Perfect for offcuts or long goods in metal and wood businesses. Why BLT cantilever racking? - Certified German manufacturer DIN EN 1090 - Made in Germany- - All specified load-bearing capacities of the uprights and cantilever arms are statically verifiable at 100% load! - All shelving systems are supplied in a hot-dip galvanized version. They can therefore be installed both indoors and outdoors and do not rust like painted systems. Consistent appearance for many years. - We use the legally prescribed hot-dip galvanized screw fittings in accordance with DIN EN 15048-1 - We use the legally prescribed C4 load plates in accordance with DIN EN 15635 / BGR 234 - Long after-sales guarantee - The upright base and upright back are welded together, providing additional safety and short assembly times because the feet do not have to be bolted to the upright back. - Bracing made of angle steel, so no adjustment with turnbuckles necessary. This shortens the assembly time. - No slotted hole system, so no weakening of the upright profile. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation. Are you interested or do you have any questions? Simply contact us by message or phone call. You can find our telephone number on our company page. ☎️ Blsdsxzdbfspfx Ad Aer You can reach us by phone from Monday to Friday, 08:00 - 15:00. Alternatively, you can send us a message with your name and number and we will get back to you as soon as possible.

Condition: used, Year of construction: 2019, Used machine Year of construction: 2019 Equipment and technical data: - Designed for classic nesting processing with wear plate - Machine frame in welded construction with ground and hardened prism guides for the gantry, unit head, and consoles - Gantry design traveling column - Helical rack and pinion drive in X and Y directions; ball screw drive in Z direction for precise positioning - Processing dimensions: - Max. support area on nesting table: X = 3100 mm Y = 1560 mm - Max. traverse paths: X = 4695 mm Y = 2100 mm Z = 293 mm - Max. clearance height over DYNESTIC table: Z = 100 mm from table top (without wear plate) - Maximum programmable speed: Vector speed: 128 m/min X = 80 m/min Y = 100 m/min Z = 25 m/min - DYNESTIC table: - Fixed, continuous processing table with grid layout - Continuous grooves in X and Y direction - Groove spacing: 50 mm - Includes 25 meters sealing cord for clamping the wear plate - Vacuum zones: single-circuit vacuum system - Drilling unit 7877: - 19 spindles - Drive power: 1.7 kW - 13 vertical spindles: - Individually selectable - U-shaped arrangement - 5+4 in X and 4 in Y direction - 32 mm grid - Max. drill diameter: 35 mm - Total drill length: 70 mm from mounting end (depends on panel thickness) - Spindle stroke: 70 mm - Rotation direction: clockwise/counter-clockwise alternately - n(max): 1000 - 4400 rpm infinitely variable Blodpfx Aowkbbdjd Asr - Holder: M10 thread – 11 mm fit - Without tools and holders - 6 horizontal spindles: - 2 double drilling spindles in X direction - 1 double drilling spindle in Y direction - Holder: M10 thread, 11 mm fit - Max. total drill length: 63 mm from mounting end - Without tools and holders - Milling unit 7842: - Power: 12.0 kW (S6) - n(max) = 1000 - 24000 rpm infinitely variable - Max. power at 12000 to 24000 rpm - Air-cooled - With HSK-F 63 tool holder - With right-hand threaded nut (for right-hand rotating tools) - With collet chuck with HSK shank - Ceramic ball bearings (hybrid bearings) - Max. tool weight: 6 kg (including holder) - Tools: milling and grinding tools max. Ø 160 mm - Safety guard according to CE standard - Safety fencing at sides and rear - Vacuum pump: 500 m³/h, dry-running - Personnel safety via light barriers in the front machine area - Handheld control unit for remote operation with the following functions: - Start/Stop machining program - Speed control for machining cycles - Reset button - Manual feed/rapid traverse for all axes - EMERGENCY STOP - CAMPUS V7 CAD/CAM software 1x machine license comprising: - CAMPUS NC-HOPS: - Graphic variant system with dialog programming and CAD/CAM functions for creating part variants with macro technique - CAMPUS MT-Manager - CAMPUS Workcenter - CAMPUS DXF interface - Automatic central lubrication - Automatic lubrication at defined intervals - Additional dust protection by overpressure in each guide carriage - Simultaneous lubrication for all linear ... (text evidently continues)

Condition: used, Spectro Type: SpectroMaxX LMD08 / LMX08 Date: 24.07.2020 Full analysis with the stationary spark spectrometer SpectroMaxX: With the help of the spark spectrometer, the alloy contents and accompanying elements of macroscopic solid samples can be can be determined with high precision down to the ppm range. Different analysis methods are available for the base materials iron, aluminum, magnesium, copper, nickel, titanium and lead, measuring methods adapted to the relevant alloy families are available. Advantages: Fast analysis within a few seconds Highly accurate spectral analysis including C and N Compact design (table-top device) Areas of use / application: Testing the chemical composition of 31 ferrous and non-ferrous metals Composition of 31 ferrous and non-ferrous metals metals, nitrogen and other elements Description of the system: Open spark stand for high sample throughput Wide range of sample geometries possible Simple change of base The following elements are available as a base: Al, Cu, Fe, Mg, Ni, Ti, Pb The analyzable elements and concentration levels depend on the methods available for the respective base element Usable wavelength range 170-670 nm Output of measured values in concentrations or intensities Selectable output units (%, ppm) Output of statistical characteristic values (mean value, RSD) SPECTROMAXx LMX08 Bljdsu S Ahqepfx Ad Asr Technical specifications: CCD optics: High-resolution CCD multi-detectors Stabilized against temperature fluctuations Effective wavelength range: 140-670 nm, the applicable and configured wavelength range is wavelength range depends on the customer's application requirements. Automated profiling Analysis modules: Freely selectable analysis modules Optimized to customer requirements Expansion with additional modules possible on site Spark stand: Open spark stand for high samples Throughput and various sample geometries Minimized argon consumption thanks to argon saving module Optimized argon flow Reduced cleaning intervals Spark stand plate can be easily replaced Temperature-absorbing design without water cooling Integrated shutter system for optimum plasma view Excitation system: Fully digitized plasma generator with digital discharge definition, digital pulse generation and digital offline pulse control 32 MHz microcontroller Max. Spark duration: 4000 µs Max. Spark power 4 kW Display system: Separate microcontroller for each CCD Serial source interface Spectrometer: External, state-of-the-art computer PC system with Windows operating system Keyboard and mouse Monitoring Software: Spark Analyzer Pro MAX software for analytical operation and calibration Continuous automatic hardware diagnostics in the background Automatic verification and identification of alloy/quality Results Manager Online maintenance scheduler Ambient conditions: Room temperature: 10-30°C Conditions: (10-30°C) Relative humidity:

Condition: excellent (used), Year of construction: 2020, PR9000 pallet racking for 36 Euro pallets This pallet racking is tested with a maximum load of 2,200 kg per beam level in accordance with DIN EN 15512 and therefore has a maximum bay load of 9,000 kg and can be loaded with 550 kg per pallet. The push-through protection prevents stored goods from slipping through when shelves are positioned parallel to each other Made of solid, high-quality steel for extreme robustness. Withstands high loads of up to 9,000 kg per bay without any problems High-quality workmanship of the entire pallet rack Plenty of storage space thanks to the 3 levels and 3 bays Eye-catching blue and orange color scheme for maximum safety Upright profile: Height: 5500 mm Material: S-355 JR steel Dimensions: 80 W x 70 D x 1.5 Perforation: 50 mm (grid - offset) Surface: Powder-coated blue Profile structure: Omega profile shape Depth: 1100 mm Manufacture: Cold-rolled profile Bay load: 9000 kg Crossbars: The height of the cross beams can be individually adjusted in 50 mm increments Total load capacity per truss level 1800 mm truss: 2000 kg 2700 mm truss: 3000 kg Blsdpfxev Hp Tuo Ad Asr 3600 mm truss: 2200 kg Material Steel S-235 JR (cold-rolled steel) Profile structure: Rectangular profile Fastening: Hook lugs on each side of the crossbeam for hooking in, secured with locking pin Finish: Powder-coated orange Manufacture: Beveled sheet steel Scope of delivery 04 x PR9000 upright 5.5 m high / 110 cm deep Bay load: 9,000 kg 18 x Cross beam PR9000 3600 cm wide incl. locking pins, shelf load: 2200 kg 09 x push-through protection PR9000 3600 mm Year 2020-2022 You can find more items - new and used - in our store! International shipping costs on request!

Condition: ready for operation (used), functionality: fully functional, total length: 2,700 mm, total height: 120 mm, total width: 50 mm, load capacity: 3,000 kg, Meta Multipal Beams – approx. 270 cm | Inspected & Used The Meta Multipal beams with an approximate length of 270 cm are from inspected used stocks and are available for immediate delivery from our warehouse. They are ideal for expanding existing Meta pallet racking and heavy-duty shelves. Additionally, they are compatible with the Jungheinrich system Type S – making them flexible for various warehousing requirements. Thanks to their robust construction and original design, they are reliable for daily warehouse operations. Specifications: Bodpfx Adexzcx As Aelr - Length: 270 cm - Height: 12 cm - Width: 5 cm - Racking system: Meta - Type: Multipal - Load capacity: up to 3000 kg - Includes safety pins - Original part no.: 402 6212 441291 - Used items, available from stock, immediate delivery possible. -- MULTIPLE UNITS IMMEDIATELY AVAILABLE -- Price: €25.00 net €29.75 gross You will receive an invoice with VAT shown separately. HAVEN’T FOUND THE RIGHT SOLUTION YET? Visit our website for a quick overview of many offers and product variations! Transport: Delivery is available upon request by our partner freight forwarder, with costs depending on your postal code. Assembly: Our trained personnel are available to assist you professionally with the assembly and disassembly of your equipment as needed. Our recommendation: Let us know your requirements... We are happy to assist you in realizing your projects, from planning and ordering to assembly. INTERESTED OR HAVE QUESTIONS? Feel free to contact us by message or phone call. You can find our phone number on our company page. ☎️ We are available by phone Monday to Friday, 08:00 - 15:00. Alternatively, send us a message with your name and number, and we will get back to you as soon as possible.

Condition: like new (used), DYEMANSION Type: POWERSHOT C 2.0 This system has never been put into operation. (as good as new!!) Dyemansion Powershot C blast cabinet Surface-friendly cleaning of powder-based plastic components DYEMANSION POWERSHOT C 2.0 Year of construction: 2021 The industry standard for simple and efficient powder removal Automated depowdering increases your production capacity With the Powershot C, a medium-sized installation space can be depowdered in just ten minutes. The time you need for parts cleaning, and personnel in your production can be significantly reduced. This increases your efficiency. By investing in automated depowdering with the Powershot C up to four manual blasting systems can be replaced. Gentle surface treatment thanks to intelligent hardware functions The blast cabinet of our Powershot C is equipped with a rotating basket and lined with stainless steel. Different blasting nozzles and ionization ensure reproducible results. A basket with a soft, replaceable lining protects the parts from damage during the process. Two simultaneously operating blasting nozzles are arranged perpendicular to the rotating basket and the parts it contains. This configuration guarantees efficient powder removal. High ease of use with improved ergonomics and process control Experience a new level of process control with touchscreen and integrated control panel. The Powershot C is operated via a user-friendly interface and pre-installed programs can be started. Individual programs can be easily configured and saved. The user-centered design makes everything easily accessible and safe to operate. Continuous monitoring enables an efficient and reproducible process. Technical data: POWERSHOT C AUTOMATION Individual programming, control and monitoring of the process parameters via control panel and touchscreen. PERFORMANCE: Processing time: Variable from 1 to 40 minutes, usual throughput time 3 to 10 minutes Capacity per cycle: Up to 3/4 EOS P396, 1x HP Jet Fusion 4200/5200 or nearly 1.5x full Stratasys H350 build space Effective volume of the basket 26 liters DIMENSIONS: System (L x W x H) 1700mm x 1310mm x 2030mm Bjdpfx Adotq E N Ej Aslr Recommended space requirement in operation (L x W x H) 2500mm x 2915mm x 2300mm WEIGHT: System 480 kg Power: Power 1kW Requirements 3x400V> 1kW 50Hz 2,5A PRESSURE AIR: Consumption Minimum: 1.4m³/min at 2.2bar Maximum: 1.8m³/min at 5bar NOISE EMISSION: Sound level < 80dB(A) Condition: used / second-hand Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: excellent (used), Denso Type: Denso 6-axis Robot VS-087 / Controller 410200-2611 A VS087-AV6-C3N model features a Cleanroom Class 3 protection specification. Denso industrial robot with Denso controller. Industries and Applications: The VS-087 series delivers high speed and high performance in a compact, slim housing. In addition, numerous options are available, making operation possible in a wide range of environments. Thanks to its high-speed performance, precision, and the variety of available options, the VS-087 can be used in nearly any sector, including automotive, chemical, consumer goods, electronics, food, greenhouse, machine tool, medical devices & pharmaceutical, plastics, and metal industries. The robot model can be used for assembly, inspection, alignment, material handling, tending, packaging, palletizing, and custom applications. Denso 6-axis Robot VS-087 with Denso Robot Controller 410200-2611 The compact model impresses with outstanding performance and speed. Robot model VS-087A4-AV6-C3N-ANNDN-NNNN Reach: 905 mm Payload: 7.0 kg Cycle time: 0.34 sec Repeatability: ±0.03 mm Weight: 51 kg Bledpfx Askx Hu Aod Aor Year of manufacture: 2016 Condition: used Scope of delivery: (See picture) (Technical data subject to change and errors excepted!) For further questions, feel free to contact us by phone.

Condition: used, PANalytical PANalytical X’Pert PRO MPD X-ray Diffractometer (XRD) Excerpt from the service report: Device: PANalytical X’Pert PRO MPD Report date: 07.07.2021 Work performed: - Reinstallation and commissioning of the system - Connection of external supply lines - Warm-up phase - Complete alignment of goniometer and additional components - Maintenance carried out, including replacement of defective parts Spare parts used: L 3.6V NC/U3 R15.0X52.0 BATTERY. NI-CD FAN FOR X-CELERATOR UNIT FILTER, WATER Motor PW3050 ("Device was not tested in-house") The X’Pert PRO MPD is a highly versatile and powerful X-ray diffractometer (XRD) designed for structural characterization of crystalline materials. It is ideal for pure research as well as routine applications in industry and academia. Thanks to its modular design, fast detection, and control of temperature and atmosphere, it is excellently suited for both routine analyses and complex in-situ experiments. Key features: - Multiple measurement geometries possible: - Reflection measurements in Bragg-Brentano (θ–2θ) mode Bledpfxswycatj Ad Aer - Transmission geometry for powders in capillaries - Optional SAXS (Small-Angle X-ray Scattering) for nanostructure analysis - Radiation source and detectors: - Typically copper anode (Cu-Kα, λ ≈ 1.54 Å) - X’Celerator detector (1D, ultra-fast) for parallel data acquisition - Modular system with PreFIX technology: - Rapid change of optics and sample stages without recalibration - In-situ measurements at high temperatures: - Measurements up to approx. 1200°C possible - Controlled atmosphere: air, nitrogen, oxygen (limited for reducing atmospheres) Typical applications: - Phase analysis and quantitative Rietveld refinement - Determination of crystallite size, microstrain, residual stress - In-situ investigation of phase transitions, oxidation, crystallization, etc. - SAXS measurements for analysis of nanoparticles and pore structures - Broad range of sample types: powders, thin films, ceramics, pharmaceuticals, catalysts, and more Technical data (typical) Property & Specification Angle range (2θ): approx. 0.5° to 150° Step size: up to 0.002° or finer Goniometer: vertical, 0–0, radius approx. 240 mm Temperature range: room temperature up to approx. 1200°C Atmosphere: air, N₂, O₂ (limited for reducing atmospheres) Detectors: X’Celerator (1D), proportional counter Distribution & application areas: The X’Pert PRO MPD is in use worldwide at, for example: - Universities (ETH Zurich, TU Dresden, University of Vienna) - Research institutes (e.g., Max Planck Institutes, ICN2, IS2M) - Industry (e.g., materials development, pharmaceuticals, chemistry) Condition: used Scope of delivery: (See image) (Specifications and technical data subject to change and error!) For further questions, we are happy to assist you by phone.

Condition: used, Trumpf TRUMPF TruDisk 6602 (4C) High-Power Disk Laser with up to 6.6 kW Type: TruDisk 6602 (4C) Blodpfx Adjwy Uyxs Aor The TRUMPF TruDisk 6602 (4C) is a high-performance disk laser offering approximately 6.6 kW of continuous power output – perfectly suited for welding, cutting, and surface treatment processes for metals such as steel, aluminum, copper, etc. System type: TruDisk 6602 (4C) Manufacturer: TRUMPF Laser GmbH + Co. KG Year of manufacture: November 2012 Drawing number: 20-10-02-A5 No further in-house inspection has been performed. Operating hours could not be read out. The laser was operating flawlessly until decommissioning. Key Technical Features: • Power: Continuously adjustable from 80 W up to 6,600 W, max. 6.6 kW for machine tool applications • Beam quality: < 2 mm·mrad for excellent focus handling • Wavelength: 1030 nm (infrared), adaptable to green wavelength for specific models • Output options: Up to 4 laser outputs (4C) for simultaneous supply of multiple process cells • Cooling system: Integrated heat exchanger (up to 28°C inlet temperature), optional compressor cooling (up to 38°C) • Modular and service-friendly: Compact footprint (< 1 m²), modular components for fast maintenance and service Benefits & Applications • Maximum process stability: Real-time power regulation ensures reproducible results • Reflection resistance: Patented resonator design enables welding of reflective metals such as copper and aluminum • Industry 4.0 ready: Sensor-integrated monitoring system, OPC-UA interface for condition monitoring & predictive maintenance • Energy efficiency: Up to 50% reduction in power consumption thanks to intelligent pulse control and energy-saving modes • Versatility: Application range includes welding (including BrightLine for nearly spatter-free seams), cutting, hardening, casting processing, additive manufacturing, laser wire deposition welding, and more Suitable Use Cases: Ideally suited for industrial high-power laser applications: Application | Features ---|--- Automotive structural part manufacturing | Deep penetration welding with high reproducibility Copper welding | Particularly suitable with green wavelength (> 95% spatter reduction) Remote hybrid welding | Fast processing of large surfaces with robust beam Additive manufacturing & hardening | Enabled by excellent beam quality and compact design Main Technical Data Property | Specification ---|--- Laser power | Up to 6,600 W (6.6 kW), continuous Beam quality | < 2 mm·mrad Wavelength | 1030 nm (infrared) Number of outputs (4C) | Up to 4 simultaneously usable fiber outputs Fiber connector diameter | 100–600 µm (depending on configuration) Beam delivery | Fiber-based, passive (no deflection mirrors required) Cooling | Water/air-cooled, internal or external chiller Dimensions | Approx. 1000 × 800 × 2100 mm (W×D×H, variant-dependent) Weight | ~800–1200 kg (excluding cooling) Power supply | 380 V - 10% ... 460 V +10%, 3-phase AC + PE, 38 kW / 41 kVA, 59 A / 400 V, 50–60 Hz Control | TruControl 1000/3000, OPC-UA interface Safety standards | Laser safety class 4 according to EN 60825-1 Weight: approx. 1200 kg Condition: used Scope of delivery: (See image) (Subject to changes and errors in the technical data. Information may be subject to alteration!) We are happy to answer any further questions you may have by phone.

Condition: excellent (used), Here we offer an inspection device for crystal silicon solar modules. Reliable quality assurance & process control during the entire solar module production The Dr. Schenk solarInspect series was developed to meet the special requirements in the production of crystal silicon solar modules. These ready-to-use Vision Systems provide reliable quality control for the entire ongoing production process. In addition, in the event of process deviations, continuous monitoring of the production process can be corrective action in good time. In the production of crystal silicon solar modules, structural glass substrates are used instead of uncoated glass. Structural glass increases the permeability of sunlight. The optical signals in the vision system, which are characterized by the surface structure, which is usually used for glass substrates of silicone solar modules, are often similar to, or even stronger than, the error actually inspected. With SolarInspect, Dr. Schenk has developed and manufactured a system that aims to distinguish between glass structure and and errors on the entire material surface, including the edges. Thanks to an innovative optical design, Dr. Schenk's inspection system can clearly detect the glass defects and distinguish them from the glass structure. Reliable inspection of - uncoated input glass Bledpfxed N Ervj Ad Aer -

Condition: excellent (used), Perkin Elmer PerkinElmer Lambda 950 UV/Vis/NIR Spectrometer – High-Precision Laboratory Instrument For sale is a PerkinElmer Lambda 950 UV/Vis/NIR spectrometer, a top-of-the-line model for demanding measurements in the ultraviolet, visible, and near-infrared range. This device is ideally suited for material analysis, optical coatings, reflection and transmission measurements, as well as numerous other applications in research and industry. Special features: Thanks to its modular design, the instrument can be optimally adapted to specific measurement tasks – ideal for research institutions, universities, and high-tech industries. Technical highlights: - Wavelength range: 175 – 3300 nm - Resolution: up to ≤ 0.05 nm (UV/Vis), ≤ 0.20 nm (NIR) Blsdpow T Sm Uefx Ad Aer - Light sources: Deuterium and tungsten-halogen lamp - Detectors: Photomultiplier (UV/Vis), PbS detector (NIR, Peltier-cooled) - Extremely low stray light: ≤ 0.00007 %T at 220 nm - Modular expandability (integrating sphere, URA, large sample chambers, and much more) Technical specifications: - Dimensions (W × D × H): 1,020 mm × 740 mm × 300 mm - Sample compartment (Primary): 200 mm × 300 mm × 220 mm (W × D × H) - Sample compartment (Secondary): 480 mm × 300 mm × 220 mm (W × D × H) - Weight: approx. 77 kg Condition: used Scope of delivery: (see picture) - PerkinElmer Lambda 950 spectrometer - Standard accessories (sample holders, cables) - Operating software & manual (Subject to changes and errors in the technical data. All information without guarantee!) For further questions, feel free to contact us by phone.

Year of construction: 2023, condition: like new (used), Thermo Fisher Type: ARL easySpark metal analyzer Analysis table spectrometer with PC, monitor and software Thermo Scientific OXSAS 2.7 software OXSAS is the most modern software for optical emission spectrometers. Current analyses are displayed in tabs. Immediate editing of data sets using fill-down and increment-down tools OXSAS is a multi-processing application with amazing capabilities and potential. The comprehensive functionality of OXSAS enables it to meet all your requirements. Technical machine description: Condition: fully functional In mint condition Year of manufacture: 02/2023 Technical description of the system: The ARL easySpark metal analyzer is designed to meet the challenges and requirements of small to medium-sized plants and laboratories in the metal industry that require high-quality but cost-effective OES analysis for the production of parts for the automotive, aerospace, consumer goods and other industries. The device impresses with its particularly high resolution thanks to a unique optical system based on multi-grating/CCD (charge-coupled device). Additional benefits of the Thermo Scientific ARL easySpark analyzer include: The ability to accurately analyze all elements, from trace levels to percent, in all solid metal samples A breakthrough spark excitation and optical design to ensure best-in-class performance Intuitive, user-friendly Thermo Scientific OXSAS analysis software for a quick learning curve and easy routine operation A robust and reliable design that requires minimal maintenance Compliance with safety and quality guidelines A simple design that is suitable for both novice production users and expert lab staff The instrument is ideal for other areas such as metal recycling, academic and non-academic laboratories and primary metal producers where a cost-effective solution for analyzing metal products and materials for quality assurance and process control or a secondary instrument is required. Power connection: 110-230 VAC, 50Hz or 60Hz Max. power: 600 VA Dimensions: Approx. L x H x D 0.80m x 0.45m x 0.70m Weight: Approx. 80 kg Blodpov Hbvbofx Ad Aer Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have over the phone.

Condition: used, Glasses Type: ACM 18 Machine control: SIEMENS PLC S7-1200 Safety controller: SICK Flexi Soft 1 media circuit (hydrocarbon) Feed pump: adjustable gear pump (24 V) Vacuum pump: diaphragm pump (230 V / 50 Hz) 1 liftable/pivoting membrane holder with 3 removable cascade rings for filter membranes with a diameter of 47 mm. System filter: 0.2 µm; length: 5 inches Return filter: 5.0 µm; Length: 5 inches System pressure: maximum 6 bar Maximum flow rate: 2.0 l/min Bljdpowaypfsfx Ad Aer Minimum flow rate: 0.250 l/min Maximum system temperature: 41°C Tank volume: approx. 12.8 liters Tank can be filled via a manual 3-way ball valve Recirculation and reuse of the rinsing medium Permissible ambient temperature: +15…+25°C Noise emissions are below 70 dB (A) Flow-cap top with 1 particle filter (separation efficiency: 99.995%; filter class: H14 HEPA filter according to EN 1822) Employee protection against splashing analysis fluid thanks to a sliding guard Collecting tray under the membrane holder Operation via 12" BASIC touch panel (optional COMFORT panel) Operation via glass keypad and stylus with the 12" option COMFORT touch panel 32 different test programs, each with 30 rinsing steps Functions: Spraying, rinsing, ultrasound Basin 750 x 600 x 500 (W x D x H) mm with a usable volume of approximately 5 l for ultrasound (with hemisphere Ø300) Hinged safety screen with three movable panels for manual access (protects employees from splashing analysis fluid) Quick coupling in the basin area for connecting various nozzles. A 2.5 mm diameter nozzle is included. Insertion opening for components: approx. 1100 x 2200 mm (W x H) Basket for ultrasonic application for components up to 3 kg Product support grid for components up to 15 kg Extraction methods: spraying, rinsing, internal rinsing (optional), ultrasound Medium: Cold cleaner A III Analysis membrane Ø 47 mm (up to 3 pieces) Blank value: < 150 µm (from at least SaS 2 or SaS 3) Power supply (machine): 230 VAC 10%, 50/60 Hz Rated power: 500 W Rated current: 2 A Back-up fuse: 16 A (max.) Supply cable: at least 3 x 1.5 mm² Control voltage: 24 VDC3) External dimensions: H x W x D 1922 x 800 x 893 mm Weight: 324 kg Condition: Used Scope of delivery: (See image) (Subject to change and errors in the technical specifications, information is subject to change!) We are happy to answer any further questions you may have over the phone.

Condition: excellent (used), BIO-CIRCLE Type: RWR 80L Auto KST Description: RWR 80 L KST fully automatic SPS parts washer The RWR units from Bio-Circle are the optimum solution for cleaning internal circulation systems without dismantling. The unit is space-saving, quiet and very easy to operate. Thanks to the completely closed system, there is no unpleasant odor from the cleaner or the dirty water. External dimensions → approx. 1200 x 800 x 1050 mm Power supply → 400 V 50 Hz plug 16A CEE 5p 6h Drain → 1 1/4" outlet Technical specification: Type of soiling: limescale, rust (mineral), oil, grease Quantity of parts: Individual parts, small series, small quantities Component geometry: Whole components (without disassembly) Seal of quality: Stainless steel, service package available Maximum filling capacity: 80 L Tank material: V2A stainless steel Electrical connection: 400V / 50 Hz Heating: 4.5 kW Bjdpjtqfbbsfx Ad Aslr Flow rate: 25 l/min Temperature (default setting): 60 °C Total weight of the cleaning system without tank filling: 180 KG Area of application: The RWR 80 L KST fully automatic PLC has been developed for the plastic injection molding sector and can be used wherever cooling channels (circulation systems, pipes) need to be cleaned. Application: Fill the RWR 80 L KST fully automatic SPS with Power Cleaner KST 2.0. As soon as the minimum fill level is reached and the system is switched on, the system starts to heat up. During the heating-up period, the system can already be connected to the tool via the two hoses. The 5-stage cleaning program and the flow direction change run automatically, after the instructions shown on the display have been confirmed. Condition: used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have over the phone.

Condition: excellent (used), functionality: fully functional, Tennant Type: T7+ ec-H2O™ Compact design with high maneuverability Product description: Bedpjv Tvq Hofx Ad Aelr Clean hard floors comfortably, nimbly, and economically: with the battery-powered Tennant T7+ ride-on scrubber-dryer. Thanks to its compact design, the ride-on machine is ideal for gaps and narrow aisles. The optional ec-H2O NanoClean technology reduces water and detergent consumption. Compact design – ideal for aisles and elevators. Clear sightlines and simple controls. Optimal water suction – no cleaning agent residue. Optional ec-H2O-Clean technology for reduced cleaning agent consumption. Easy-to-clean, hygienic tanks. Low noise level of 67 dB(A). Automatic brake and parking brake. Available in various working widths. Includes battery, on-board charger, and brush. Technical details: Area of application: Indoors. Battery operation: Voltage: 24 V. Battery type: Lead-gel battery. Battery capacity: 240 Ah/per unit. Frequency: 50-60 Hz. Speed: 6.4 km/h. Direction of travel: Reverse, forward. Noise level in dB(A): 67 dB(A). Removable fresh/dirty water tank. Fresh water tank volume: 110 l. Dirty water tank volume: 110 l. Theoretical area coverage: 5120 m²/h. Practical area coverage: 5120 m²/h Working width 800 mm Brush diameter 400 mm Brush speed 260 rpm Brush contact pressure 36 - 73 kg Brush motor power 450 W Brush-assisted drive no Brush shut-off automatic yes Tires material rubber Wheels number 3 Non-marking wheels yes Wheel width 80 mm Wheel diameter 250 mm Turning circle 1840 mm Operator cockpit yes Squeegee material Linatex Squeegee width 1000 mm Suction motor power 450 W Body color Teal Frame color Teal Height 1270 mm Width 740 mm Depth 1270 mm Weight 443 kg Version with ec-H2O™ Rim material Polyamide Condition: used / Used Scope of delivery: (See image) (Subject to change and errors in the technical specifications, information is subject to change!) We are happy to answer any further questions you may have over the phone.

Condition: used, Zeiss Type: EVO 50 XVP The instruments of the EVO product family combine powerful scanning electron microscopy with an intuitive operating concept that is equally well suited to experienced users and novices. Thanks to its extensive options, EVO can be precisely tailored to your requirements, regardless of whether you work in the life sciences or materials science Bsdpfx Aovvtnbsd Ajlr or in routine industrial quality control and failure analysis. Scanning electron microscope EVO 50 XVP, EDX from Oxford Xplore 30 SDD detector without N cooling 05/2021 Dimensions: DxLxH 930 x 1930 x 1600 mm 30mm 2 sensor size / resolution 129MnKa at 100,000cps From boron - califonium Software AZtec lite on Windows 10 With drift correction Analyser quali-quanti-analysis Point ID Mapping Line scan Damping system included each container carries 116kg/bar Operating hours approx. 11,500 hours PC upgrade to Windows 10 05/2021 The scanning electron microscope is fully functional. Weight 750 kg + 385 kg +150 kg Condition: used (Changes and errors in the technical data, information are reserved!) Please ask about the transport options before purchasing. We will be happy to answer any further questions you may have over the phone.

Condition: excellent (used), Stäubli Type: TX90L Robot / CS8C Controller Six-axis robot with controller The high-performance robots of the TX90 series for medium payloads offer maximum flexibility for a wide range of applications thanks to their compact, slim design. Thanks to three mounting options: floor, wall, and ceiling, the six-axis robots are easy to integrate. The fully encapsulated design (IP 65) enables use in clean rooms or under aggressive environmental conditions. Features Fully encapsulated design with internal supply lines Rigid structure Multiple mounting options Patented Stäubli JCM gear modules Long reach Advantages Perfect component protection. Standard version in clean room class ISO 5. Easy to clean. Excellent dynamic path behavior High flexibility Precision, dynamics, and speed with reduced maintenance requirements Optimal use of the workspace Technical specifications TYPE TX90L Number of degrees of freedom: 6 Nominal payload: 6 kg Maximum payload: 15 kg Reach: 1200 mm Repeatability: ±0.035 mm Protection class (wrist) IP65 (IP67) Mounting options: Floor / Wall / Ceiling Stäubli CS8 CS8C controller Features Ethernet, fieldbus, digital inputs and outputs, serial interfaces Easy to integrate, 19-inch rack version, protection class IP20 All connections on the front Proven digital technology Advantages Open architecture Compact Good accessibility Reliable Technical specifications: Type CS8C Dimensions (H x W x D) 331 x 445 x 455 mm 481 x 445 x 455 mm Protection class IP20 (IP54 optional) RAM 64 MB RAM (min.) Bljdpjwbqwcefx Ad Aor Storage capacity 128 MB (min.) Flash disk and USB port System/Programming language VAL 3 (multitasking interpreter language), PLC-IEC 61131-3 language Communication Serial interface RS232/422, Ethernet, ModBus/TCP server Type: Robot TX90L / Controller CS8C Condition: Used Scope of delivery: (See image) (Subject to change and errors in the technical specifications, information is subject to change!) We are happy to answer any further questions you may have over the phone.

Condition: excellent (used), Stäubli Type: Robot TX90L / Controller CS8C Six-axis robot with controller The high-performance robots in the TX90 series for medium payloads offer the highest possible flexibility for many applications thanks to their compact, slim design. Thanks to the three mounting options - floor, wall and ceiling - the six-axis robots are easy to integrate. The completely encapsulated structure (IP 65) enables use in clean rooms or under aggressive environmental conditions. Features Completely encapsulated structure with internal supply lines Rigid structure Multiple mounting options Patented Stäubli JCM gear modules Long range Advantages Perfect protection of the components. Standard version in clean room class ISO 5. Easy to clean. Blsdpfx Adjvx Tbto Ajr Excellent dynamic path behavior High flexibility Precision, dynamics and speed with reduced maintenance effort Optimal use of the work space Technical data TYPE TX90L Number of degrees of freedom 6 Nominal load capacity 6 kg Maximum load capacity 15 kg Range 1200 mm Repeatability ±0.035 mm Protection class (wrist) IP65 (IP67) Mounting options floor / wall / ceiling Control Stäubli CS8 CS8C Features Ethernet, fieldbus, digital inputs and outputs, serial interfaces Easy to integrate, 19-inch rack version, protection class IP20 All connections on the front Proven digital technology Advantages Open architecture Compact Good accessibility Reliable Technical data: Type CS8C Dimensions (H x W x D) 331 x 445 x 455 mm 481 x 445 x 455 mm Protection class IP20 (IP54 optional) RAM 64 MB RAM (min.) Storage capacity 128 MB (min.) Flash disk and USB port System/programming language VAL 3 (multitasking interpreter language), language PLC-IEC 61131-3 Communication Serial interface RS232/422, Ethernet, ModBus/TCP server Type: Robot TX90L / Controller CS8C Condition: used Scope of delivery: (See image) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have over the phone.

Condition: excellent (used), Rofin Type: PowerLine Pico 532 - 10 CombiLine Basic WT VLM - Visual Laser Marker VLM is an innovative, flexible marking software that is used on Rofin laser systems. laser systems. VLM follows the WYSIWYG concept and offers the flexibility of a the flexibility of powerful yet easy-to-use software. VLM can be used to apply markings of various types such as matrix codes, barcodes and serial numbers, barcodes and serial numbers. Depending on the material, even the smallest markings are possible. The innovative software ensures reliable marking of reliable marking of flat and curved surfaces, and οη-the-fly applications are also possible. Common formats such as DXF or optionally PDF are supported for importing layouts. Technical data of the laser: Laser head Wavelength: 532 nm Bljdpfx Adjtz Rk He Aor Power: approx. 3W at 400 kHz Pulse frequency: 200-800 kHz, Beam quality: TEMoo Energy per pulse: 7.5 μJ at 400 kHz , 3.5 μJ at 800 kHz Peak power: 7.5 kW at 400 kHz Dimensions: approx. 450 mm X 168 mm X 235 mm (L X W X H) Weight: approx. 14 kg (with standard Galvo RM10) 19" supply unit Dimensions: 2HEx19''x350 mm(HxWxD) Weight: approx. 20 kg Cooling: integrated air cooling Supply voltage: 115 - 240 V +/-10%50 ا Hz / 60 Hz Power consumption: approx. 800 W Ambient temperature: 15°- 35°C, non-condensing Air flow rate: 80 m³/h PC Mini-ΙΤΧ SSD removable disk 250 GB Software at least VLM 5.2 Windows Embedded Standard 7 Other options 19" panel can be removed Positioning aid Adjustable 3-foot support The following components were additionally selected from the standard scope of delivery: Ρ255-532 lens ٢= 255 mm: 532 nm Labeling field 180 mm X 180 mm S10-532 Galvo head unit S10: 532 nm Galvo head S10 including selected objective, holding set for optics and protective protective glass or protective glass slider. Size: approx. 165 mm X 118 mm X 147 mm (L X W X H) Weight: approx. 4.4 kg CombiLine Basic (V2): The CombiLine Basic is a user-friendly laser class 1 system (in accordance with EN 60825-1 ), which, thanks to the use of largely preconfigured functional preconfigured function modules, enabling optimum adaptation to customer-specific requirements. The frame contains all control components and functional elements. functional elements. An aluminum plate with standard or customer-specific workpiece holders, an aluminum plate with a standard drilling pattern serves as the basis. The fully automatic, electrically operated door enables workpieces to be loaded and unloaded. The machining area can be viewed at any time through the large observation window. A programmable z-axis, including control and motor, is included as standard, is used for vertical focus adjustment. This takes place in automatic mode according to the specifications of the marking program. Technical data: Dimensions: approx. 1200 mm X 1750 mm X 800 mm (W X H X D) Door opening: approx. 560 mm X 680 mm (W X H) Weight: max. 380 kg Connection: 230V+/-10%: 1/Ν/ΡΕ Power: max. power consumption 3 kVA Monitor: 15" TFT with touch function Z-axis: max. 300 mm stroke Workpiece: max. 20 kg Weight (incl. holder) max. 690x 490x 293 mm (W x L x H)