Used Kel Varia for sale (1,399)

Year of construction: 1995, condition: ready for operation (used), overall weight: 6,000 kg, product length (max.): 3,600 mm, This KELLENBERGER Kel-Varia cylindrical grinding machine was manufactured in 1995. It features a Kellenberger Kelco 90 control system and a robust internal grinding device with a B-axis for a tiltable grinding head. The machine supports a tip height of 175 mm and a tip width of 1,000 mm, equipped with a belt filter system. Ideal for precision grinding tasks. Contact us for more information about this machine. • Capacity: Center height 175 mm; between centers 1000 mm Fodpfx Abeybb T Tsuspc • Configuration: Internal grinding device; B-axis tiltable grinding headGrinding head and B-axis • Grinding heads available: R, RS, UR • R head pivot: +30° • RS/UR heads, rotating part indexing: • Manual indexing: 180° to -190°, 2.5° steps • Automatic indexing: 180° to -90° (or -30°), 2.5° steps • B-axis (RS/UR heads): pivot +180° to -190° (some variants limited to about +30°); resolution 0.1"Workhead • Standard workhead (C-axis): pivot -30° to +120° • Spindle speed: up to 600 rpm (stepless) • Mounting taper: MK5; reduction sleeve MK5/MK4 • Adapter flange: MK5 / DIN 55027 size 5 • Torque capacity: 160 Nm • Max workpiece between centers: 150 kg • Workhead with rotating spindle: • C-axis pivot: -30° to +120° • Spindle speed: 5–500 rpm (stepless) • Mounting taper: MK5 • Torque capacity: 320 Nm (incl. clamping device) • Max workpiece between centers: 220 kgTailstock • Taper: MK4 • Quill stroke: 50 mm • Micro-adjust (option): ±150 µm (±0.006 in)Grinding wheels and internal grinding • UR head: • Left wheel max: 400 × 63 mm • Right wheel max (option): 400 × 50 mm • Max peripheral speed: 32 m/s • R head: • Wheel max: 500 × 100 mm • Max peripheral speed: 32 m/s with 7.5 kW motor; 45 m/s with 9.2 kW motor • RS head: • Wheel max: 500 × 80 mm • Max peripheral speed: 32 m/s with 7.5 kW motor; 45 m/s with 9.2 kW motor • Internal grinding (option/device on this machine): • Mounting bore for high-performance spindles (HJN): 80 mm • Mounting bore for high-frequency spindles (MFV): 120 mmAxes and tables • Z-axis (lower table): • Max speed: 15 m/min • Resolution: 0.1 µm • Travel (1000 mm between centers version): 1150 mm • Upper table swivel range (1000 mm between centers): 0 to +9° • X-axis (grinding slide): • Max travel: 320 mm • Max speed: 7.5 m/min • Resolution: 0.1 µmDrive motors • X-axis slide: 0.94 kW (2000 min⁻¹) • Z-axis table: 0.94 kW (2000 min⁻¹) • Indexing / B-axis: 0.63 kW (3000 min⁻¹) • Grinding spindle UR: 4.4 kW @ 50 Hz (3000 min⁻¹) / 5.2 kW @ 60 Hz (3600 min⁻¹) • Grinding spindle R/RS (7.5 kW version): 7.5 kW @ 50 Hz (1500 min⁻¹) / 9 kW @ 60 Hz (1800 min⁻¹) • Grinding spindle R/RS (9.2 kW version): 9.2 kW @ 50 Hz (1500 min⁻¹) / 11 kW @ 60 Hz (1800 min⁻¹) • Workhead (standard & rotating): 3.1 kW (3000 min⁻¹) • Hydraulic pump: 0.37/0.44 kW (1500/1800 min⁻¹) • Hydrostatic pump: 0.37/0.44 kW (1500/1800 min⁻¹)Dimensions, weight, utilities (1000 mm between centers version) • Floor space (L × W): 3600 × 2000 mm • Weight: net 5000 kg; gross 6000 kg • Minimum air pressure: 4 bar • Noise emission: 70 dB(A) Additional equipment • Belt filter coolant system

Condition: used, Year of construction: 1997, 2 x cylindrical grinding machines Kellenberger type: kel varia, year of manufacture 1997 and 1995. Technical data and more pictures available on request. Fsdsx T A Iwspfx Abuopc

Year of construction: 1997, condition: ready for operation (used), number of axes: 4, This 4-axis KELLENBERGER Kel-Varia UR 175/1000 was manufactured in 1997. It features an internal grinding device with a tiltable B-axis and a C-axis for out-of-round grinding, complemented by a belt filter system. Consider the opportunity to buy this KELLENBERGER Kel-Varia UR 175/1000 cylindrical grinding machine. Contact us for more information. Additional equipment • Belt filter system Machine Benefits Technical Machine Benefits • Internal grinding device with b-axis for tiltable grinding head and c-axis for out-of-round grinding Extra Information Center height x center distance: 175 x 1,000 mm Complete with standard accessories, electrical equipment For three-phase current 3 x 400 volts, 50 Hz. Machine color: DARK GRAY NCS 7502B combined with BLUE NCS KEL-ASSIST 90 PLUS software package Internal grinding attachment with 80 mm diameter chuck Right-hand grinding wheel attachment, 400 x 50 mm diameter Oil mist lubrication device for HJN spindles Micro-adjustment on the tailstock Face-spiral three-jaw chuck, 160 mm diameter Dressing device on the upper table Pivoting diamond holder 9.5 mm MOVOMATIC lead-in sensor Set of vibration-damping pads Set of lubricant for initial filling CNC-controlled C-axis Fjdpfx Abjx T Dg Ioujpc

Condition: used, Year of construction: 1995, grinding diameter 350 mm grinding length 1000 mm Fpedpfxsyatx So Abusc centre height 175 mm Teilüberholte Maschine mit Messprotokoll nach Neumaschinentoleranz NEUE Steuerung Eckelmann ENC mit BEMA Schleifsoftware KEL-ASSIST für Kelco 90 numerisch gesteuerte B-Achse Innnschleifrinrichtung Dia 80mm Schleifscheibe links Durchmesser 400mm Schleifscheibe rechts Durchmesser 300mm Innenschleifspindel HJN 828 hydraulischer Reitstock Mikroverstellung KEL SET Messsystem

Condition: used, Year of construction: 1995, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Fsdpjxyadaefx Abuopc Completely overhauled in 2013 Heavy duty workpiece headstock tailstock Without chuck and without bezel in the photo Kelco 90 control The machine can be viewed in operation at the customer's premises from 2025 up to and including January 2026.

Condition: good (used), Year of construction: 1999, operating hours: 16,000 h, functionality: fully functional, machine/vehicle number: 650341, Year 1999 with Fanuc 18 TB – 3 axes XZB Marposs E30/E20 Fjdpfxsw T Tb Hs Abuepc Country of manufacture: Switzerland Voltage: 400V/50Hz/3ph Dimensions: 410 x 220 x 190 cm Net machine weight: 5,000 kg TECHNICAL SPECIFICATIONS CNC control: Fanuc 18TB Intermediate Section Fixed intermediate section: grinding head R Swiveling section with manual indexing 2.5°: R / RS / UR / URS -210° to +30° Swiveling section with automatic indexing 2.5°: R / RS / UR / URS -210° to +30° B axis, resolution 0.1'': R / RS / UR / URS -210° to +30° Standard workhead Swivel range: -10° to (+100°) Spindle speed (continuous): 6 – 600 rpm Internal taper: MT5 Reducing sleeve: MT5/MT4 Short external taper fitting: DIN 55026 / Size 5 Permissible torque: 160 Nm Guaranteed roundness for chuck work Standard: 0.5 µm Option: 0.2 µm Workpiece weight between centers: 150 kg Tailstock Taper fitting: MT4 Quill stroke: 50 mm / 2° Option: fine adjustment with correction (Ø +/- 150 µm) Grinding wheel data (max. speed) Diameter 300: 27 m/s Diameter 400: 35 m/s Diameter 500: 45 m/s UR Grinding Head Power: 9.2 kW / 12.5 HP Wheel mounting, left max.: Ø 500 x 80 mm Right, additional max.: Ø 400 x 63 mm Internal grinding device: spindle HJN 828 Lower table (Z axis) Distance between centers: 1000 mm Max. travel: 1150 mm Max. speed: 15 m/min Max. resolution: 0.1 µm Upper table Distance between centers: 1000 mm / swivel 0° to 9° Grinding carriage (X axis) Max. travel: 320 mm Max. speed: 7.5 m/min Max. resolution: 0.1 µm Pneumatics Min. connection: 6 bar Air consumption: approx. 0.6 m³/h Coolant Max. connection pressure: 3 bar Required space (version 1000): 3600 x 2000 mm Unless otherwise stated, technical data is provided without engagement and may be subject to errors or omissions.

Condition: used, KELLENBERGER KEL-VARIA R175 x 1500 is a CNC cylindrical grinder engineered for high precision, top accuracy and reliable production. Capacities: centre height 175 mm, distance between centres 1500 mm, Z-axis 1650 mm, workpiece weight on centres max. 150 kg; grinding wheel Ø500×80 mm (bore 203 mm) or Ø400×63 mm (bore 127 mm); max wheel travel 320 mm. Key specs: wheel speeds stepless 1000–2150 rpm (peripheral speed 45 m/s); feed 7500 mm/min; work spindle swivels -10/+100° with 8–800 rpm; permitted load 160 Nm; grinding spindle motor 7.5 kW; work spindle motor 2 kW; 3×400 V 50 Hz; rapid 15 m/min; approx. weight 6000 kg; dimensions 4700×2300×2000 mm; air 6 bar. Accessories: coolant system, paper filtration, MARPOSS touch probe, set of grinding wheels, rotary centre, set of centers, set of workpiece drivers, set of throat gauges, lamp, 2 tool cabinets, tailstock with fine adjustment, oil mist extractor, spindle nose for collets. Achieves tight tolerances; typical applications: automotive, watchmaking, machine tool Fedpfx Absxx U S Asuepc

Condition: used, KELLENBERGER KEL-VARIA 2RU 225/1500 is a CNC cylindrical grinder engineered for precision, high accuracy and reliability. Capacities: centre height 225 mm, distance 1500 mm, max grinding Ø 432 mm, workpiece weight 150 kg; wheels L 400×63×127, R 500×80×127. Wheel speeds 1000–2150 rpm (45 m/s); work spindle 8–800 rpm, taper 5 CM, permitted load 160 Nm. Tailstock taper 4 CM, stroke 50 mm, pressure 200–700 N; supply 3×400 V 50 Hz. Options: KEL‑ASSIST 100, MOVOMATIC, KEL‑SET, MOVOMATIC C25, KEL‑BALANCE, coolant through spindle, paper filtration, 400 mm magnetic chuck, dressing, swivel diamond holder. Enables tight tolerances; sectors: automotive, watchmaking, machine tools, aerospace, medical. Fpsdpfx Abexx U Haouoc

Condition: used, Year of construction: 2000, grinding diameter 450 mm grinding length 1000 mm centre height 225 mm Photo of machine already delivered in similar scope: -major maintenance -New table geometry -partial painting of the interior grinding wheel equipment LEFT 400x63x127mm (standard) grinding wheel equipment RIGHT 300x40x127mm Internal grinding unit Ø120mm for HF spindles CNC control KELCO 120 C-axis for non-circular grinding. Kel-Poly B-AXIS: CNC-controlled B-axis KELCO 120: v constant 35m/s or 45m/s High-frequency internal grinding spindle Operating unit for MFV and MFZ spindles Hydraulic quill retraction for the tailstock NO micro-adjustment on the tailstock Spring-loaded quill insert Top table cooling Standard workpiece headstock MK 5 DIN 55026 size 5" Micro-adjustment for the standard workhead Fpodpfx Abjxzk Nisuec Dressing device on the lower table Active longitudinal positioning KELPOS, MARPOSS, mounted on the grinding head Tool measuring system KELSET, MARPOSS MARPOSS gate sensor Measuring control MARPOSS Minialsar prepared Paper belt filter

Condition: used, Year of construction: 2003, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Fpsdpfx Aexflcrsbujc

Condition: used, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your is: Kellenberger Kel-Varia Baureihe mit Kelco 90 Steuerung. Mechanische Überholung: -komplette Maschine nach Kellenberger Messprotokoll überholt -Neue servicefreundliche Kabine -Neulackierung Elektrische Überholung: -Neue moderne CNC-RUNDSCHLEIFMASCHINEN-Steuerung -Neu aufgebauter Schaltschrank -Neue Antriebstechnik -Austausch sämtlicher elektrischer Leitungen Berus Druckschalter etc. -Neue Absolut-Glasmaßstäbe in x- und z -Neuer Absolut Drehgeber (Bei-B-Achse) Standardausstattung: Fpedpouwv H Tefx Abuec -WSS mit Konus MK5, optional mit Adapter MK5/Kurzkegel -RST mit MK4 Konus. Optional mit Feinverstellung -Schleifspindelstock T1/T2/T3 -T1 Schleifscheibendurchmesser 400mm -T2 Schleifscheibendurchmesser 300mm -T3 Innenschleifeinrichtung riemengetrieben. -Schleifspindelmotor 4,4kW -B-Achse hochauflösend -Marposs Messsystem zur Schleifscheibenvermessung. -Längspositionierung Marposs -GAP Control (Sensor am Schleifspindelstock) Optionen gegen Aufpreis: -HF Innenschleifspindel -Hochgenauer, höchst kippsteifer Werkstückspindelstock -Messteuerung Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your is: Kellenberger Kel-Varia Baureihe mit Kelco 90 Steuerung. Mechanische Überholung: -komplette Maschine nach Kellenberger Messprotokoll überholt Fedpfx Ajuwv H Hsbuepc -Neue servicefreundliche Kabine -Neulackierung Elektrische Überholung: -Neue moderne CNC-RUNDSCHLEIFMASCHINEN-Steuerung -Neu aufgebauter Schaltschrank -Neue Antriebstechnik -Austausch sämtlicher elektrischer Leitungen Berus Druckschalter etc. -Neue Absolut-Glasmaßstäbe in x- und z -Neuer Absolut Drehgeber (Bei-B-Achse) Standardausstattung: -WSS mit Konus MK5, optional mit Adapter MK5/Kurzkegel -RST mit MK4 Konus. Optional mit Feinverstellung -Schleifspindelstock T1/T2/T3 -T1 Schleifscheibendurchmesser 400mm -T2 Schleifscheibendurchmesser 300mm -T3 Innenschleifeinrichtung riemengetrieben. -Schleifspindelmotor 4,4kW -B-Achse hochauflösend -Marposs Messsystem zur Schleifscheibenvermessung. -Längspositionierung Marposs -GAP Control (Sensor am Schleifspindelstock) Optionen gegen Aufpreis: -HF Innenschleifspindel -Hochgenauer, höchst kippsteifer Werkstückspindelstock -Messteuerung Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr... Fpsdpfjuxfu Nsx Abuec

Condition: used, Year of construction: 2002, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m Photos of identical machine with centre height 225mm Base: Kellenberger Kel-Varia UR175-1000 Kelco 120 Grinding head UR with T1-T2-T3 Basic equipment: -T1 500mm grinding disc diameter -T2 400mm grinding wheel diameter -Infinitely variable, high-resolution axis -Marposs measuring device for tool measurement -Active longitudinal positioning -GAP on T1 and T2 from ELASO contactless integrated in the control interface Semi-automatic balancing from ELASO integrated into the control interface -Tailstock with manual retraction -MK5 workpiece headstock with short taper DIN 55026 Belt-driven internal grinding device Options at an extra charge: - New high-precision workhead with torque drive - Internal grinding device for high-frequency spindles diameter 120mm -HF internal grinding spindle Fischer MFM-1224/42/31 D-21 -HF spindle with HSK holder 24,000 rpm with integrated GAP sensor. (delivery time) -CNC-controlled C-axis non-circular grinding -hydrostatic threaded spindle in x -new hydrostatic unit with only 1 pump and pressure accumulator thus better energy efficiency. -monitoring of the water content in the hydrostatic system -Suction system Further options available on request Mechanical overhaul: -Complete machine overhauled according to Kellenberger measurement protocol -New service-friendly cab -repainting Electrical overhaul: -New modern CNC CIRCULAR GRINDING MACHINE control with BEMA rough grinding surface -New control cabinet -New drive technology -Replacement of all electrical cables Berus pressure switches etc. -New absolute glass scales in x and z -New absolute rotary encoder (for B-axis) Control system: Fsdpfx Abouxfucjuspc The grinding software consists of a basic licence and various options that are possible depending depending on the equipment of the machine. Basic software - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal taper pendulum grinding - External and internal radius grinding, radius dressed on disc - Semi-automatic pendulum grinding - Workpiece zeroing - Grinding wheel zeroing - Measuring the dressing diamonds - 2 moulding diamonds - 1 shaped diamond or dressing roll (dressing roll required) - Moulding roller (dressing roller required) - 3 Flat dresser - Corrections - Z-position measurement (probe required) - GAP probing (grinding device required) OPTIONS at an extra charge: Software profile plunge-cut grinding: - External and internal profile plunge-cut grinding with profile disc Profile grinding software: - External and internal profile grinding with straight disc Software thread grinding: - Single and multi-start external and internal thread grinding with thread on the disc disc Dressing. Dressing of single and multi-groove discs. Flank angle freely selectable. Trapezoidal thread grinding software: - Additional dressing of trapezoidal threads possible External and internal non-circular plunge-cut grinding: - External and internal non-circular plunge-cut grinding Non-circular grinding software: A prerequisite for non-circular grinding is that the workpiece axis is equipped with a high-resolution rotary encoder so th...

Condition: used, grinding diameter 350 mm Fjdpfx Abst Ii Rfjuopc grinding length 1500 mm centre height 175 mm Grinding wheel left 500mm diameter Grinding wheel head fix. No swivelling possible. With new control. With new enclosure Overhauled according to Kellenberger protocoll

Condition: used, Year of construction: 1995, functionality: fully functional, grinding length: 600 mm, grinding diameter: 250 mm, The machine was still in operation until recently. Grinding diameter: 250mm Grinding length: 600mm Notes: - The price does NOT include any accessories! Fsdpfx Abjwca Hcjuepc - Pickup by buyer, from the site. - Pickup date to be agreed upon by the seller. - No warranty. - Advance payment (invoice) or cash upon pickup.

Condition: used, Distance between centres: 1000 mm Centre height: 250 mm B-axis: Accuracy 0.1" CNC brand: Kelco CNC model: 90 Left grinding wheel dimensions (OD x ID x width): Ø400 x Ø127 x 63 mm Right grinding wheel dimensions (OD x ID x width): Ø400 x Ø127 x 50 mm Workhead swivel: -30º to +120º Workhead taper: MK 5 Max. workpiece weight between centres: 150 kg Tailstock taper: MK 4 Tailstock quill travel: 50 mm Maximum peripheral speed: 32 m/s High-frequency internal grinding spindle: Ø120 mm High-frequency internal grinding spindle brand: WARNER model K 3.000 Main motor power: 7.5 kW Total power: 26.5 kW Max. Z-axis travel: 1,150 mm Max. Z-axis feed speed: 15 m/min Worktable rotation: 0º to 9º Max. X-axis travel: 320 mm Max. X-axis feed speed: 7.5 m/min Length: 3,600 mm Fjdpfx Ajxmg Eksbuepc Width: 2,000 mm Approx. weight: 5,000 kg

Condition: used, Year of construction: 2021, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Control Fanuc 31i Maschine aus 1998 jedoch 2021 überholt von Kellenberger inklusive neue Steuerung FANUC31 mit Blue solution Nur 790 Stunden Schleifzeit 1 UR-175 / 1000 Standardausführung (T1, T2, T6, T7) 1 Schleifscheibenausrüstung T1 500x80x127mm 1 Schleifscheibenausrüstung T2 400x63x127mm 1 HF-Innenschleifeinrichtung T6 MFM 1224/42 42.000 U/min 1 HF-Innenschleifeinrichtung T7 MFM 1242/60 60.000 U/min 1 Spitzenhöhe 175mm 1 CNC Steuerung FANUC 31i mit Blue solution 1 Unrundschleifen 1 Remote Diagnostic 1 B-ACHSE CNC-gsteuert 1 Reitstock mit pneumatisch betätigten Pinolenrückzug 1 MIKROVERSTELLUNG: Reitstock Unterteil mit Mikroverstellung 1 Werkstückspindelstock mit C-Achse 1 Werkstückspindelstock mit schwenkbarem Unzerteil 1 KELPOS: Aktive Längspositionierung 1 Vorbereitung für Messsteuerungen Movomatic ESZ 400 oder Marposs P7 ME Fsdex Rn Uwopfx Abuepc 1 KELSET : Werkzeugvermessungssystem 1 Grundmodul für Anschnittsensoren und Auswuchteinrichtungen Fluid-Anschnittsensor mit Magnetfuss 1 Vollverschalung Emulsion 1 Kühlmittel-Reinigungspistole am Tisch angeschlossen 1 Vorbereitung für Schleifnebel-Absauganlage Emulsion

Year of construction: 2015, condition: excellent (used), I offer on behalf of a customer from Switzerland this machine. It is with 5.200 h in an excellent condition. Used in prototyping, currently operational Fpedsgtingjpfx Abuec Equipped with: Grinding head UR T1 500 x 80; T2 400 x 63 1 HF internal spindle MFM 1224/42 1 HF inner spindle MFM 1290 Semi-automatic balancing device KEL-TOUCH on the work headstock for internal and external grinding KELSET grinding wheel measurement KELPOS longitudinal positioning Heidenhain CNC GrindPus 640 CNC B - axis, hydrostatic CNC C - axis for polygon and thread grinding KELSOFT NCG for non-circular grinding KELTHREAD for thread grinding KELREMOTE for remote diagnosis Prepared for measuring controls Paper belt filter Streuli 480 l Extraction system available at short notice from location Switzerland

Condition: excellent (used), Year of construction: 2004, functionality: fully functional, center height: 175 mm, workpiece weight (max.): 180 kg, grinding length: 1,000 mm, grinding wheel diameter: 400 mm, total length: 1,150 mm, grinding diameter: 349 mm, The machine is in working and usable condition in our workplace. There are 2 outer diameter and 2 inner grinding machines, it has a C axis. Fpsdov Uxriepfx Abuec

Condition: good (used), axle configuration: 2 axles, first registration: 06/2019, loading space length: 13,670 mm, loading space width: 2,460 mm, loading space height: 2,790 mm, suspension: air, color: white, Year of construction: 2019, Equipment: ABS, tail-lift, = Additional options and accessories = - Air suspension Fodpfx Aeyh Ehfsbuspc = Notes = Kel-berg box trailer - Zepro load lift 2,500 KG - Steering axle MY: 20-6-2019 SKBS35B23KKE23134 Box: 13.67 - 2.46 - 2.79 Zepro load lift 2,500 KG Steering axle = Further information = Axle brand: BPW Suspension: Air suspension Rear axle 1: Dual wheels; Max. axle load: 10,000 kg; Tire profile left inner: 50%; Tire profile left outer: 50%; Tire profile right inner: 50%; Tire profile right outer: 50% Rear axle 2: Dual wheels; Max. axle load: 10,000 kg; Steered; Tire profile left inner: 50%; Tire profile left outer: 50%; Tire profile right inner: 50%; Tire profile right outer: 50% gross vehicle weight: 35,000 kg Tail lift: Zepro, tailgate Technical condition: good Optical condition: good

Condition: good (used), axle configuration: 2 axles, first registration: 06/2019, loading space length: 13,670 mm, loading space width: 2,460 mm, loading space height: 2,790 mm, suspension: air, tire size: 265/70R19.5, color: white, Year of construction: 2019, Equipment: ABS, tail-lift, = Additional options and accessories = Fpsdpfx Absyh Egzsujc - Air suspension = Remarks = Kel-berg Box trailer - Zepro loadlift 2,500 KG - Steering axle MY: 6-6-2019 SKBS35B23KKE23133 Box: 13.67 - 2.46 - 2.79 Zepro loadlift 2,500 KG Steering axle = Additional information = Tire size: 265/70R19.5 Suspension: Air suspension Rear axle 1: Twin tires; Max. axle load: 10,000 kg; Tire profile left inner: 30%; Tire profile left outer: 30%; Tire profile right inner: 30%; Tire profile right outer: 30% Rear axle 2: Twin tires; Max. axle load: 10,000 kg; Steered; Tire tread left inner: 30%; Tire tread left outer: 30%; Tire tread right inner: 30%; Tire tread right outer: 30% GVW: 35,000 kg Tail lift: Zepro, tailgate Technical condition: good Visual condition: good

Condition: used, maximum load weight: 18,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, first registration: 10/2004, loading space length: 5,046 mm, loading space width: 2,325 mm, Year of construction: 2004, Equipment: ABS, Manufacturer Kel-Berg Model 3 axle Asphalt Tipper / Kipper Year 2004 Condition Good Serial Number SKBD23B304AKE9692 Ref. nr. 7937 Reg. date: Drum brake: ? ABS: ? Fpodpfjyhx Tbjx Abujc Tire Size: 385/55R22,5 Cover% left 40-60% Suspension: Air Total weight: 24000 Kg Net weight: 5300 Kg Load capacity 18700 Kg Inside length: 5046 mm Internal width: 2325 mm

Condition: used, maximum load weight: 33,525 kg, overall weight: 46,000 kg, axle configuration: > 3 axles, first registration: 04/2008, Year of construction: 2008, Equipment: ABS, Manufacturer Kel-Berg / Faymonville Model 4 akslet 3 m Udtræks Maskintrailer Year 2008 Fpjdpfx Aexa Tdmobusc Condition Good Serial Number SKBE58S407KE12547 Ref. nr. 7972 Reg. date: 30-04-2008 Last seen: 27-01-2025 Drum brake: ? ABS: ? Rear axles: SO F Suspension: Air Tire Size: 235/75R17,5 Cover% left 30-50% Toolbox: ? Total weight: 46000 Kg Net weight: 12575 Kg Load capacity 33425 Kg Inside length: 8.75m / 12.10m Extraction: 3 m Forced steering axles: 3+4 Hydraulic ramps: ? Hydraulic rear support leg: ?

Condition: used, empty load weight: 8,760 kg, axle configuration: 2 axles, first registration: 06/2019, loading space length: 13,625 mm, loading space width: 2,480 mm, loading space height: 2,780 mm, loading space volume: 94 m³, tire size: 265/70 R19,5, Year of construction: 2019, Equipment: tail-lift, Leergewicht: 8760kg, Laderaum (L B H): 13.625 mm x 2.480 mm x 2.780 mmReifengröße: 265/70 R19.5, Laderaum Volumen: 94 m³, 1. Achse: , 2. Achse: , Unterfahrschutz statisch, Ladebordwand stehend Stahl, Nachlauflenkung, Ferry Lashings, Anschlußstecker 1x15 und 2x7 polig, Unser gesamtes Fahrzeugangebot finden Sie unter . Finanzierung gewünscht? Mit unseren Value Added Service bieten wir Ihnen individuelle Finanzierungsmöglichkeiten, Full Service-und Telematik-Dienstleistungen. Wir beraten Sie gerne. Fpodpfx Aeyb Ugaebusc