Used Scraper for sale (637)

Condition: used, Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Replacement of all plastic sliding plates for the hydraulic push floor. Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. All six limit switches (proximity sensors) on the push floor were replaced. The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. Bodpfx Afey Urtfjkown All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), puncher 100 t square edge steel 50 x 50 mm round bar steel 50.0 mm L-beam 150 x 150 x 13 mm hole punching press: capacity (dia. x thick.) Ø 30.0 x 26 mm shear: flat material 600 x 15 mm throat 300 mm work stroke 80.0 mm work height max. 1165 / 960 mm total power requirement 9.0 kW weight 2250 kg range L-W-H 2050 x 1200 x 2050 mm well-maintained condition (!!) current new price approx. 30.000 euros special price on request Equipment: - electro-hydraulic profile steel shears with 4x work stations * Flat steel shears * Profile steel shears * Hole punch * notching station - driven by two hydraulic cylinders - Infinitely variable stroke adjustment - Support table at hole punching station - Material scraper - Lateral storage options - 2x freely movable foot switches - Many accessories included in the scope of delivery * swiveling machine lamp * Various punch dies * Spare blades for the flat steel station ... etc. - Operating instructions (PDF) Bwsdpfxoy Uy Spo Afkon

Condition: used, Suitable for steam heating capacity 800L. all stainless steel double jacket tiltable drum stirring system with scrapers with mixer steam (4 bar) Bedpfxey S Tzxo Afkewn dimensions (l x w x h) : ± 2.600 x 2.200 x 2.700 mm

Condition: used, Year of construction: 2006, Used machine Year of manufacture: 2006 Condition: completely overhauled Equipment and technical data: - fitted with new glue application system Bjdowka H Sspfx Afkjwn - manually adjustable infeed fence - milling unit 1961 - edge feeder 1903 - glue application station 1906 with tracking nozzle - pressure unit 1816, pneumatic - end trimming unit 1822 - milling unit 1942 M for radius, chamfer, flush trimming - complete air nozzle - scraper unit 1929 - chip collection box - surface scraper 1964 - extraction hood set - complete safety covers - total length: 5,291 mm - workpiece thickness: min. 6 / max. 50 mm - edge band thickness depending on configuration: 0.4–5 mm - max. edge band height: 55 mm - minimum edge band strip length: 350 mm - max. edge band overhang/height per side: 3 mm - minimum workpiece width: 60 mm - minimum workpiece length: 180 mm - feed speed: 12.5 m/min - extraction: - jointing/milling unit: 900 m³/h - milling unit: 280 m³/h - scraper unit: 280 m³/h - static vacuum: - jointing/milling unit: 1,490 Pa - milling unit: 1,650 Pa - minimum air velocity: 20 m/sec - jointing/milling unit connection: 70 mm - scraper unit connection: 70 mm - compressed air: 6 bar Availability: short notice Location: Röllbach

Condition: used, Used Becomix model Beco Mini RW 2.5 lab scale homogenising mixer.  Bwodpsyx Ibgsfx Afksn Manufacturer: Becomix. Capacity: Working capacity 0.5-3.5L. Dimensions: 800mm x 800mm x 900mm high. Also includes: -Integrated CIP system. -Agitator with scrapers. -Intuitive touch panel PLC control.  -Compact device with tempering unit. -Vacuum pump. - PLC control integrated into a mobile table. -Mixing vessel full vacuum to 1 bar, double jacket 4 bar.

Condition: excellent (used), Edge Banding Machine HEBROCK K36 Airtronic -used- - PC control with display - Touchscreen - Swiveling control panel - Program memory - Automatic pressure bridge adjustment - Feed via transport chain - Extendable workpiece support - Motorized adjustable infeed fence - Diamond jointing cutter, both with and against feed direction - Quick heating gluepot - Gluepot change system - Suitable for PUR adhesives - Cross-cut saw with HF motor - Flush milling unit - Flush, radius, and chamfer milling unit - Pneumatic changeover of milling unit - Multi-milling tool - Multi-radius scraper blade - Chip collection box for radius scraper blade - Air jet nozzle at the radius scraper - Flat scraper blade - Air jet nozzle at the flat scraper - Exchangeable motor for corner rounding - Spray device for separator agent - Spray device for cleaning agent - Spray device for antistatic coolant - Spray device for lubricant - LED lighting in the machine area - Exchange gluepots - Zero Joint Airtronic System ----- Technical Data ----- - Edge thickness, coil material: 0.5-3 mm - Max. edge thickness for corner rounding: 3 mm - Workpiece thickness: 8-60 mm - Workpiece thickness for corner rounding: 45 mm - Min. workpiece length: 200 mm - Feed speed: 7-10 m/min - Support plate Ø for edge material: 850 mm - Guillotine for coil material up to: 3 mm - Jointing cutter power: 2x2.2 kW - Cross-cut saw power: 0.37 kW - Milling station power: 2x0.37 kW - Corner rounding unit power: 0.37 kW - Buffing unit power: 2x0.18 kW - Extraction port Ø jointing unit: 60 mm - Compressed air connection: 7 bar - Total length: 5,540 mm Bwjdpfx Asymyp Rsfksn - Dimensions (LxWxH): 5,540x1,210x1,450 mm - Weight: 1,700 kg Quality Information: - All settings checked - Complete basic inspection - Complete basic cleaning - Electrical system checked - Pneumatics checked - Immediately ready for operation

Condition: new, Edgebanding Machine HOLZ-HER 1308 XL AURIGA POWER -Showroom machine- Innovation: GLUJET GJ725 This offer concerns an equipment package. Bwodpfx Aeu R Sy Asfksn The following components and options are already included in the price: - Extendable workpiece support - Edge Control PPC 322 W control system - ECO MODE energy-saving mode - Jointing cutting unit FG201 with 2 milling heads - Diamond milling cutter Ø 70 x 64 x 30 mm, Z2+2, left-hand rotation - Diamond milling cutter Ø 70 x 64 x 30 mm, Z2+2, right-hand rotation - Edge feed 1903 - Glue application system Glu Jet GJ725 NC PUR PRO - Pressure unit 1912-3 pneumatic - End trimming unit 1918 pneumatic 60 mm - Multifunctional milling unit FR301 MOT6 - Diamond milling cutter Ø 56/60 mm, left-hand rotation - Diamond milling cutter Ø 56/60 mm, right-hand rotation - Corner rounding unit FF301 MOT1 - Scraper unit ZK301 MOT4 incl. high-gloss package - Carbide reversible knives for scraper carrier - Chip collection box for scraper unit - Buffing unit 1940 - Spray device TR301 for infeed and outfeed areas - Motorized pressure bridge adjustment - iTronic-adaptive pressure and glue quantity control - Extended infeed fence 1,252 mm - Motorized adjustment for infeed fence - Pressure unit DW301 with motorized NC axis - Extraction hoods for end trimming unit 1918 - Shelving program - Surface scraper FK701 - Spray device GM301 after the pressure unit - new showroom machine -

Condition: excellent (used), Edge banding machine FORMAT 4 Tempora 60.06 glueBox - used Touchscreen, pivoting control panel, program memory, automatic pressure bridge adjustment, feed via conveyor chain, extendable workpiece support, diamond jointing cutter for up- and down-feed, glue pot located underneath, glue pot changing device, use of PUR adhesives possible, GLUEBOX, printing unit with driven roller, cross-cut saw with 2 HF motors, pneumatically pivoting cross-cut saw, flush/radius trimming unit, motorized positioning control of the trimming unit, x-motion PLUS, corner rounding unit with diamond-coated cutter, radius scraper, radius scraper with motorized positioning, surface scraper, operation-controlled Surface scraper, Inlet barrier, Release agent spray device, Lubricant spray device, Cleaning agent spray device, Year of manufacture 2022 ----- Technical specifications ----- Bodpfsu R S Nwex Afkewn Edge thickness for rolls: 0.4 - 3 mm, Edge thickness for strips: 3 - 6 mm, Workpiece thickness: 8 - 60 mm, Min. workpiece length: 140 mm, Feed speed: 10 m/min., Screen diagonal: 15 inches, Dimensions of jointing cutter: D 80 x 64 mm, Joining cutter power: 1.1 kW, Crosscut saw power: 0.35 kW, Milling station power: 0.75 kW, Extraction nozzle Ø: 80 + 160 mm, Compressed air connection: 7 - 10 bar, Total length: 4,872 mm, Dimensions (LxWxH): 4,872 x 1,511 x 1,468 mm, Weight: 1,500 kg Quality information: - All settings checked - Adjusted according to manufacturer's specifications - Complete basic inspection - Complete basic cleaning - Electrical system checked - Pneumatic system checked - Ready for immediate use

Year of construction: 2022, condition: used, Manufacturer : Buhler Haas-Mondomix B.V. Model: HAKA type VA-15L Year : 2022 Type : Foam / Aerator mixer Previous application : Application : Whipped cream Production capacity : 100 kg/hr nominal Input density : 1,0 kg/l Output density: 0.6 – 0.8 kg/l   Near as new condition. Unit consisting of : – Pre-mixer PCM 400 litres Capacity: 400 litres Design: conical bottom Lid with hinged access for manual loading of ingredients Jacketed, insulated and protected tank Stirrer: cutting blade + Teflon scrapers PT100 temperature sensor – HALA type dispensing pump with frequency converter Volumetric pump with frequency converter Jacketed design Bodex R A Rtopfx Afkewn Mass flow meter with regulator – HAKA VA-15L type continuous aerator Rotor / stator with 912×5 mm square lugs Effective volume 2 ltrs Mixing head stator Double-walled front and rear plate for cooling Rotor designed for cooling Temperature sensors Jacketed piping 7.5 kW direct drive motor, frequency converter controlled Air injection: manual or automatic with mass flow meter Automatic pressure control and regulation Cabinet + PLC, Siemens S7 type – HANB cold water production unit Autonomous chilled water unit (thermoregulation) for cooling the expansion head tank Water temperature between 5°C-20°C Spiral heat exchanger / Centrifugal pump / Closed water tank – CIP Easy Clean system for easy cleaning Stainless steel platform supporting all equipment

Condition: good (used), Year of construction: 2019, Pieralisi FP600 RS-M decanter centrifuge, 2-phase decanter centrifuge, 15 kW drive, max. drum speed 4100 rpm, equipped with backdrive with 7.5 kW drive, scraper for solids with 0.25 kW drive, product temperature min. 5 °C and max. 100 °C, excl. switch box, incl. stainless steel control box, dimensions 2550 x 1050 x 1390 mm (lxwxh), weight 1510 kg, including various spare parts Bedpfx Aey Uvp Dsfkjwn

Condition: new, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 10,500 mm, loading space width: 2,480 mm, loading space height: 2,165 mm, loading space volume: 56 m³, Equipment: ABS, Chassis light version In aluminum (15-6-12) Two fully automatically welded I-longitudinal beams with welded cross beams. Chassis width 1,600mm Axles and suspension disc brake 430 mm Jost (ex Mercedes DCA) axle units 3 x 9 t with air suspension, air bellows in central arrangement to the chassis longitudinal beam, 1st axle liftable with starting aid and manual forced lowering, Smart Board Infocenter, raising/lowering valve, BVA brake wear indicator Tires and wheels 6 wheels with tires of size 385/65 R22.5 from manufacturers of choice, with steel rims 11.75 x 22.5 ET 120 Seatposts mechanical version with one-sided operation in 2 speeds with swivel base for air suspension Brake system according to E.G. Standard, Wabco two-line system, spring-loaded parking brake acting on two axles and Wabco EBS-E including RSS (Roll Stability System) and Premium Modulator, Wabco SmartboardInfocenter, aluminum air tank system electrical system according to the guidelines of the STVZO with 2 five-chamber lights type Aspöck Ecopoint 2, 24 volt system with 2x7 and 1x 5-pin socket, with side marker lights, 2 separate LED reversing lights at the rear, 1 LED headlight inside, Bwsdsfi Nmujpfx Afken Tipping body/trough body fully welded inside Aluminum trough, side walls 30 mm thick plank profiles (2-3 mm) 600 mm wide welded, floor 8 mm thick highly wear-resistant alloy (5383H34/HB 110), front wall 4 mm reinforced in straight design, rear wall as universal door in straight design with 2 wing doors in 2/3-1/3 version with a grain slide or ww. Version in 1/2-1/2 version possible with one grain slider each, aluminum round profile welded on to the side and bottom of the rear doors to seal the door gap, rear doors partially covered with smooth aluminum, operation of the universal door can be automatically pneumatically locked with a separate lever, aluminum rear bow can be swung out, two hold-down devices with rubber buffers attached to the tipping trough to the frame on the bulkhead Hydraulic system tipping ram with large cover Hydraulic ram mounted on the bulkhead with a max. working pressure of 150 bar, made by Edbro, with approx. 2.5m hydraulic hose and loose half 1", tilt angle approx. 48 degrees Accessories 6 Parlok fenders, complete mud flaps attached to the U-guard across the entire width of the vehicle, aluminum spare wheel holder, side collision protection on the right in a foldable version, tool box type 860 large, approx. 3 m aluminum ladder, 3 aluminum swivel bows 150 mm raised in the middle, additional centrally mounted bow holder for positioning a total of 2 bows to increase the loading width, roll-up tarpaulin with a central light strip and separate reinforcements in the wear areas in approx. 660 gr. /m2 quality with roll-up tarpaulin system, all-round rubber rope at the rear end of the tarpaulin with two tow hooks to be attached to the swivel bow at the rear, walkway on the frame in chassis color, tarpaulin closure with quick-release fastener, tarpaulin closure at the rear with welded-in rubber rope to prevent water ingress, robust foldable underrun protection with ww. two towing eyes on the left and right including locking bolts, 2 "Clear-Pass" mud flaps on the fender in accordance with EC standards, attached to the side of the frame, an aluminum grain hopper with tarpaulin bag, holder for shovel, broom and scraper mounted above the axles, etc... +590¤ transfer costs available in 50m³ - 56m³ 9,700mm and 10,500mm loading space length * the price varies depending on th

Condition: used, Year of construction: 2010, Used machine Bjdpsy E Avlofx Afkjwn Year of manufacture: 2010 Features and technical data: Right-hand version 2 auxiliary tables are still in original packaging H&H / HARDO TH 1020-V46 BV DA (twin system) Maximum application width: 2,040 mm (2 × 1,020 mm) Design: Twin system, both machines can also be operated individually Application roller: reinforced version Application roller diameter: 46 mm Application roller knurling: 0.5 mm Bearings: reinforced roller bearings Bearing shells: hardened Scraper: pneumatically actuated, needle bearings Main bearing lubrication: routed externally, to be filled with a manual grease gun Container seal: adjustable and replaceable without removing the application unit Application speed control: via frequency converter Speed range: 3.2 – 19.3 m/min Control: potentiometer Display: digital speed display Pressure rollers: 2 pieces, silicone-coated Pressure roller length: 2,040 mm Pressure roller diameter: 159 mm Pressure roller actuation: pneumatic Automatic lowering of pressure rollers when drive motor is switched off Height adjustment for material clearance: electromechanically, manual inching mode Applicator unit stroke: 0 – 200 mm Conveying height: 925 mm (underside of material) Pressure roller drive: separate drive Motor: including motor mounting, fastening, and enclosure Additional application speed control: via separate frequency converter Additional speed range: 3.2 – 19.3 m/min Additional control: potentiometer Additional display: digital speed display Base frame: aluminium profile system Stands: 2 pieces, anodised aluminium plates Adjustable feet: adjustment range ±25 mm Material feed direction: right to left Heating control: programmable timer (daily and weekly program) Temperature control: electronic with digital actual value display Melt tank capacity: 2 × 25 litres Heating power: 2 × 8.0 kW Nominal power: 18.5 kW Control voltage: 24 V Nominal frequency: 50 Hz Operating voltage: 400 V Phases: 3 Fuse: 63 A Compressed air connection: < 8 bar Application: Melting and applying non-reactive hot-melt adhesives Weight: 1,560 kg Availability: short-term Location: Rhineland-Palatinate

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,250 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, power: 22 kW (29.91 HP), year of last overhaul: 2025, volume flow: 530 m³/h, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: Bjdpey R Npijfx Afkewn The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the whirling unit replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), Year of construction: 2005, Edgebander manufactured in 2005. This IMA Advantage 600 features jointing cutters, a gluing unit for thin and thick edges, and a pressing zone. It includes two trimming units, flush trimming, and profile and surface scrapers for enhanced finishing. If you are looking to get high-quality edge banding capabilities, consider the IMA Advantage 600 machine we have for sale. Contact us for further details. • Equipment/units included: • Jointing cutters • Gluing unit for thin and thick edges Bwedsy Uxfbopfx Afkon • Pressing zone • 2x trimming units • Flush trimming • MFA • Profile scraper • Surface scraper • Buffing • Return mechanism on top pressure

Condition: used, Year of construction: 2015, operating hours: 10,900 h, functionality: fully functional, overall weight: 19,000 kg, Model: Fine Shredder Doppstadt AK 510 BioPower Year of manufacture: 06/2015 Serial No.: 983 Bwedpoy Sam Usfx Afksn Location: NRW Operating hours: approx. 10,900 hrs Availability: short-term, by arrangement Standard equipment: - Central axle trailer chassis for 80 km/h - Brake system with ABS according to EC directive - 50 mm EC towing eye, bolt-on shoe - Tyres 285/65 R 22.5 - Permissible total weight 19,000 kg - Mercedes-Benz engine OM 460 LA, 375 kW at 2,000 rpm, emission standard Euro Mot III B - Load-dependent feed control incl. automatic scraper conveyor reversal - Fuel tank 600 liters - Complete radio remote control - Hydraulic drive - Hydraulic support legs - Separate drive for feed roller/scraper conveyor 'TwinDrive' - Painted in RAL 2011 deep orange Condition of the machine: The machine is in technically and visually good and ready-to-use condition. New diesel engine at 10,310 operating hours! Warranty: The machine is sold in the condition existing at the time of delivery. The seller assumes no liability for defects.

Condition: new, We supply wear parts for your Doppstadt AK 430, 435, 510, 535, 560, 635, 640, etc. Highest quality thanks to 'Made in Germany'! - Rear baskets - Rear flaps Bodpfow I Ar Rsx Afkswn - Impact plates, toothed, with counter blade, smooth - Wear plates - Scraper floor bars - Scraper floor chains - Flail tips - Flail holders - And much more.

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, operating hours: 1,651 h, workpiece height (max.): 60 mm, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, HOMAG KAL 310 + panel return system TFU 140! TECHNICAL DETAILS Profile milling unit FK11 manual Edge thickness: max. 3 mm Motors: 2 units Motor power: 0.4 kW per motor Frequency: 200 Hz Speed: 12,000 rpm Feed speed: max. 20 m/min Feed speed for continuous trimming without profile trimming: max. 30 m/min Panel length single-sided: min. 240 mm Panel length double-sided: min. 120 mm Panel thickness: 12 - 60 mm Panel spacing with PC22: min. 500 mm Minimum workpiece gap for workpiece thickness over 22 mm: min. 600 mm Multi-scraper MN21 Automatic Number of profiles: max. 5 different profiles Edge thickness: max. 3 mm Panel thickness for radius R = 3 mm: min. 13 mm Panel thickness for bevel 0.5 x 45°: min. 10 mm TC knives: 2 units Bevel angle: 20° Radius: R = 1.5 / R = 2 / R = 3 / R = 5 Pre-milling unit BF10 Motors: 2 units Motor power: 0.55 kW per motor Frequency: 200 Hz Speed: 12,000 rpm Bwedpfx Afjyzxa Ejkon Swivel range: +/- 1° TC cutter: 70 x 25 mm HSK: 25 Cutting angle: 54° Feed speed: 18-25 m/min Workpiece thickness: 8-60 mm Edging material (roll): 0.3-3 mm MACHINE DETAILS Operating hours Operating hours: 6,358 h Feed time: 1,651 h EQUIPMENT Pre-milling Automatic adjustment of the infeed fence Infeed device with 2 rollers Quickmelt application station 2-roller magazine infeed Automatic adjustment of the pressure zone HL84 end trimming unit with pneumatic adjustment BF10 flush milling unit with pneumatic adjustment FK11 profile milling unit MN21 multi-profile scraper unit for 5 different profiles Grooving unit Glue joint scraper Buffer Return system TFU140

Condition: excellent (used), Year of construction: 2014, Ref:11081 . 2014 Kolbus DA-270 Casemaker For high-speed production of hard book covers, Lever Arch files and games boards. Comprising: ‘Co-pilot’ system with touch screen for automatic size setting, menu guided make-ready and fault indication. Twin board magazine feeders Central soft spine feeder with double reel holder for auto-splice and cutter for waste *Special board centre strip cutting device Magazine feeder of pre-cut cloth with miss control Mobile hot-melt gluing unit with pre-melter* Heated glue application roller with scraper roller Cloth cylinder with grippers & exchangeable plates for rubber pad Counter shingle delivery with roller conveyor External glue application adjustment Glue viscosity device for automatic water supply control Pressing roller for crease-free cover to board application Bwedpfoyzy Rrox Afksn Single case request for operator set-up Variable DC drive Automatic lubrication Including accessories & manuals. N.B. Compressed air and water supplies to client’s account. Accessories: Board centre-strip cutting device for cutting rigid centre board strips to width, with possible width variance from product to product for digital book production. ° Board sheet thickness max. 2 mm ° Width max. 1,500 mm | height min. 140 mm | max. 390 mm ° Board centre-strip max. 7 mm | max. 60 mm Kolbus ECK standalone corner cutter to work with case maker Specification: Size of opened case, Max: 670 x 390 mm Min : 205 x 140 mm Centre strip width : 6 - 90 mm, thickness 1 – 4 mm Joint width : 4 - 15 mm Turn-in width, closed : 8 – 15 mm Output, variable : up to 65 cycles/min Floor space : L: 6700 x W: 3000 x H: 2,200 mm Electrical loading : 15 kW (3ph, 400V, 50 Hz) Air requirement : 33 Nm3/h 6 bar.

Condition: ready for operation (used), Year of construction: 2016, overall weight: 1,870 kg, Edgebander manufactured in 2016. This BIESSE Akron 1440 A features a pre-milling unit, multifunction milling units, flat trimming, and a corner rounding unit. It also includes automatic glue application, motorized adjustment of units, and a touchscreen control for ease of use. If you are looking to get high-quality edgebanding capabilities, consider the BIESSE Akron 1440 A machine we have for sale. Contact us for further details. • Condition: Used – excellent condition, regularly serviced, fully operational • Availability: Machine can be inspected under power in production; inspection/testing by prior appointment • Configuration/Equipment (integrated): Bwjdpfx Ajy Ukixefkon • Pre-milling unit • Multifunction milling units: R1, R2 • Flat trimming • Corner rounding unit (Rondomat) • Radius profile scrapers • Flat scrapers • Polishing brushes • Cleaning liquid application unit • Automatic glue application • Motorized adjustment of units • Touchscreen control • IntelliSet system • FAST setting technology • ECO mode • Technical specifications: • Power: 13 kW • Power supply: 380 V, 50 Hz, 3 / N / PE • Full-load current: 24 A • Air pressure requirement: 7 bar • Minimum workpiece width: 50 mm • Note: Transport chain is not included in the sale.

Condition: ready for operation (used), Year of construction: 2018, travel distance X-axis: 4,000 mm, travel distance Y-axis: 2,000 mm, controller manufacturer: MicroStep, controller model: iMSNC, number of axes: 3, This 3-axis MicroStep AquaCut-W 4001.20 was manufactured in 2018. It features a working range of 4,000 x 2,000 mm and is equipped with a high-pressure pump system capable of 400 MPa. The machine includes automatic height control for the cutting head and a waterjet cutting table with grid support. If you are looking to get high-quality waterjet cutting capabilities, consider the MicroStep AquaCut-W 4001.20 machine we have for sale. Contact us for further details. Bwedpfx Aoy Ui Hpofksn - CNC Control Unit: MicroStep iMSNC with MMI console, 24" touchscreen, and two LCD operator units on the gantry- Working Range / Processing Area: 4,000 x 2,000 mm- Laser Pointer: Laserpointer with automatic offset transmission- Control Modules: Expert system, Service & Maintenance wizard, CNC program loading wizard, Automatic mechanical scanning calibration, Cutting program management (MRP), EcoInfo, MachineInfo, User-Management- CAM Software: AsperWin Basic, AsperWin Select macro library, AsperWin NC-Sim simulator- Connectivity: USB 3.0 port, MicroStep Remote Diagnostics, TeamViewer access, GSM Modem for SMS error notifications- Cutting Table: Waterjet cutting table with grid support- Height Control: Automatic height control for the waterjet cutting head- High-Pressure Pump System: BFT ECOTRON 40.37- Pump Permissible Working Pressure: 400 MPa (4,000 bar)- Pump Max Flow Rate: 3.8 l/min- Pump Tank Capacity: 140 liters- Pump Power Consumption: 39 kW (at 3*400 V, 50 Hz) / 46 kW (at 3*480 V, 60 Hz)- Pump Gross Weight: 1,110 kg- Pump Serial Number: 16414- Pump Drawing Number: 120343- Cutting Head: Allfi Cutting Head Type IV (1 unit)- Abrasive Head: Allfi Abrasive Head CENTERLINE Typ II "Long Life" (1 unit)- Abrasive Systems: Allfi Abrasive Dosing system, Allfi Abrasive Conveying System Type II, Automatic abrasive dosing via CNC- Sludge Removal: Desludging system (scraper conveyor) for 4,000 mm length, including sedimentation tank- Water Conditioning: Water stabilization dosing unit using WIN2054Si water chemistry- Safety Equipment: Double-sided cable pull safety mechanism (collision protection) via Emergency Stop- Total System Layout Footprint Dimensions: Approx. 7,122 mm (Length) x 4,200 mm (Width) (Main machine footprint alone is 7,122 mm x 3,476 mm)- Required Flooring Base: Concrete min. B20, thickness min. 200 mm, surface evenness ±5 mm

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: 2026, warranty duration: 12 months, input voltage: 400 V, DGUV certified until: 06/2028, total length: 2,100 mm, total width: 1,100 mm, input frequency: 50 Hz, type of input current: three-phase, electrical fuse: 32 A, Spiral kneader / mixer Bwedpfx Afjf Etm Nekon Model: SP 220 MS LED control with temperature display / temperature control with rewind key Dough machine with 2 timers Tool speed adjustable for min / max. 10 - 220 kg of dough Flour dust hood and bowl scraper 2 tank wagons (340 liters) Standing machine with changing tools Stainless steel tools: kneading spiral, flat beater, whisk DGUV V3-tested Connection 400V, 13.6 kW, 50A 32A-CEE plug Dimensions: 1100 x 2100 x 1500 / 2300mm, WxDxH NEW machine With a 12 month warranty Come to our sales center with baking equipment and many bakery machines.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: 2026, warranty duration: 12 months, input voltage: 400 V, DGUV certified until: 06/2027, total length: 1,900 mm, total width: 1,050 mm, total height: 1,250 mm, input current: 16 A, input frequency: 50 Hz, type of input current: three-phase, power: 9.2 kW (12.51 HP), electrical fuse: 32 A, Spiral kneader / mixer Model: SP 250 MS LED control with temperature display / temperature control with rewind key Dough machine with 2 timers Tool speed adjustable for min / max. 10 - 160 kg dough Flour dust hood and bowl scraper 2 tank wagons (250 liters) Bjdof Epwnjpfx Afkswn Standing machine with changing tools Stainless steel tools: kneading spiral, flat beater, whisk DGUV V3-tested Connection 400V, 10.6 kW, 32A 32A-CEE plug Dimensions: 1050 x 1900 x 1250/2100 mm, WxDxH NEW machine With a 12 month warranty VISIT our sales center with bakery equipment and many bakery machines

Condition: used, capacity 1.000L. all stainless steel double jacket 36 kW tiltable drum stirring system with scrapers electric heating Bedpfx Ajy Nawhsfkjwn dimensions (l x w x h) : ± 1.900 x 1.900 x 1.800 mm

Condition: ready for operation (used), Year of construction: 2015, operating hours: 1,748 h, travel distance X-axis: 635 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 460 mm, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D, total height: 2,650 mm, total width: 2,530 mm, table width: 790 mm, table length: 560 mm, table load: 600 kg, overall weight: 3,900 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 17,000 W, number of slots in tool magazine: 20, product length (max.): 2,050 mm, number of axes: 3, This 3-axis DMG MORI ecoMill 635 V was manufactured in 2015. It features an X-axis travel of 635 mm, Y-axis travel of 510 mm, and Z-axis travel of 460 mm. The machine has a robust table size of 790 x 560 mm and a maximum table load of 600 kg. If you are looking to get high-quality machining capabilities, consider the DMG MORI ecoMill 635 V vertical machining center we have for sale. Contact us for further details. Bjdpfx Ajy T R I Ejfkswn • CNC control: electronic handwheel • Operating hours: Power on approx. 13,550 h; Spindle cutting approx. 1,748 h • Table: 790 × 560 mm • Spindle: 12,000 rpm; SK40 / ISO40; Power approx. 13–17 kW • Tool magazine: 20 positions; Automatic double‑arm tool changer • Feed rates: Rapid traverse 30 m/min • Coolant: Flood coolant system • Drives: Digital AC servo drives • Electrical: 400 V / 50 Hz / 3‑phase; Rated power 17 kVA • Other: Machine connected and under power; very low spindle cutting hours for the year; good technical condition Additional equipment • Scraper-type chip conveyor • Discharge height: 950 mm • Tank capacity: 200 l • Coolant spray gun for swarf removal • Standard 4-color signal lamp • PROGRESSline & Planolight package Technical Specification Taper Size SK 40

Condition: reconditioned (used), Year of construction: 2010, • Traveling distances X=3100 mm, Y=1950 mm, Z=1390 mm • Heidenhain iTNC 530 with handwheel HR 410 • Machine table for multi side working 3000 mm x 1600 mm • 2-axis NC-universal milling head, for simultaneous and positioning working • Spindel 10.000 U/min HSK 100, 130 Nm Spindle torque • Tool change system HSK 100 / 40 places for 750 mm long tools • Chip conveyor (screw type) in X-axis, for transport into • Chip conveyor scraper belt type (traverse conveyor), Fabr. Knoll • Coolant container 900 l, Fabr. Knoll • Outside air at spindle • IKZ 60 bar for deep hole drilling function • Covering with safety glass pane, open at the top for loading by crane • 2 part sliding doors at the operator side • 2 part sliding doors at the front side, for easy loading • Radio-controlled measuring probe RMP 60 • incl. washing gun • incl. podiums at the front side and operator side • complete factory overhauled and painted new • short time delivery after arrangement • used machine • Y-axis ball screw in September 2021 incl. bearings renewed • X-axis new linear guiding system, July 2023 changed, renewed • Spindle overhauled at Mai 2023 (clamping system new, clamping cartridge new, rotation unit new, general tests) (at 23105 spindle hours)) • can be visited under power at 72793 Pfullingen • optional fixators • optional installation at customers plant • optional transport Bedpfx Afjzagr Sjkswn • 23122 spindle hours in total • 53991 machine hours in total • Year of construction 2010 Subject to prior sale