Used edgebanders for sale (575)

Condition: ready for operation (used), Year of construction: 2024, workpiece height (max.): 60 mm, feed rate X-axis: 10 m/min, spindle speed (max.): 16,000 rpm, control type: PLC-controlled, The machine has already been disassembled and stored by a specialist. TECHNICAL DETAILS Rotational speed of the miter saw station: approx. 16,000 rpm Rotational speed of the milling station: approx. 16,000 rpm Maximum milling depth: 3 mm Design for edge thickness: 1 mm Hot melt adhesive specification for edge material max.: 3 mm Feed rate: approx. 10 m/min Maximum workpiece thickness: 60 mm EQUIPMENT Itsdpfxjzb Idfs Ag Uoh Maintenance-free, coated glue basin with provision for interchangeable basins Glue dispensing device Pneumatic milling adjustment Combination design with interchangeable plate cutter Corner rounding milling cutter Radius drawing blade Surface drawing blade with pneumatic extraction device Cleaning station Robust chain drive Ball-bearing mounted double roller pressure pad Aggregate viewing window from the machine's rear and operator side Signal lamp for workpiece sequence Extendable workpiece support ACCESSORIES Hebrock 8 mm version Hebrock quick-change system for corner milling cutter Hebrock jointing up to 60 mm workpiece thickness Hebrock protective spray for edges Hebrock nesting (milling cutter + radius drawing blade) Hebrock Airtronic Note: Accessories are provided without guarantee. The principle applies: "Item purchased as seen." The prospective buyer must verify the completeness of the item on-site.

Condition: excellent (used), Year of construction: 2018, Specification Length: 4605mm Workpiece Thickness: 40mm Edge Material Roll: 0.4 – 3mm Edge Material Strip: 0.4-3mm Feed Speed 8m/min Joint Trimming Unit 40mm Quick Change Application Unit Magazine for Coiled Material Pneumatic 2 point adjustment Pressure Zone End Trim Unit with Pneumatic Adjustment Pneumatic Adjustment Fine Trim Contour Trimming Unit Pneumatic Adjustment Profile Scraping Unit Glue Joint Scraper Buffers LED Indoor Lighting Iodpfxszdklcs Ag Ueth EasyTouch Control System Manual Central Lubrication Manual Top Pressure Adjustment Roller Top Pressure

Condition: ready for operation (used), Year of construction: 2017, functionality: fully functional, total height: 2,100 mm, total length: 6,700 mm, total width: 1,050 mm, empty load weight: 3,500 kg, Equipment: CE marking, TECHNICAL DETAILS Itodpfozdzmkex Ag Uoh The machine has the following configuration: 1. Unit: Nordson pre-milling unit (tools included) 2. Unit type: Gluing unit 3. Unit type: Pressure rollers (tools included) 4. Unit type: Rough milling unit 5. Unit type: Cut-off unit 6. Unit type: Fine milling unit MACHINE DETAILS Number of units: 6 Voltage: 400 V Power consumption: 41 A Fuse: 50 A Dimensions (L x W x H): 6,700 x 1,050 x 2,100 mm Weight: 3,500 kg Transport packages: 5 EQUIPMENT CE marking

Condition: used, Year of construction: 2023, machine/vehicle number: Profi-HPP300/43/43, functionality: fully functional, operating hours: 4,134 h, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 3,200 mm, workpiece length (max.): 3,800 mm, HOMAG SAWTEQ S-300 profile line CNC panel dividing saw (Profi-HPP300/43/43) with a large touchscreen and a maximum speed of 150 m/min. Specifications Manufacturer: Homag GmbH (Germany) Type: SAWTEQ S-300 profile line Design: CNC panel saw Configuration: Profi-HPP300/43/43 Year of manufacture: 12-2023 Serial number: 0-240-87-3107 Control: large touchscreen Capacity/max.: 3,200 x 3,800 x 5,600 mm Speed: 150 m/min CE: yes Design/features Clamping bar Additional loose blades Ball-roller table with air jets Dust extraction pipes Receipt printer Homag/Pica Machine manuals available Itsdpfjzd Dliox Ag Ush Recorded operating hours: Number of cuts: 31,843 Operating time: 4,134.18 hours Main operating time: 587.18 hours Condition Used Has already been professionally disassembled and moved by Kisjes Transport Apeldoorn (using a combination vehicle). Dimensions Assembled: 645 x 831 cm Photos Photo 1 to 21: assembled installation at its original location Photo 21 to 51: disassembled installation at the current storage location Auction information

Condition: ready for operation (used), Year of construction: 2008, operating hours: 7,900 h, Edgebander manufactured in 2008. This OTT Tornado features a maximum panel thickness of 60 mm and a minimum panel length of 150 mm. It includes a CombiMelt Glueing System and a double end trim unit for efficient processing. If you are looking to get high-quality edgebanding capabilities, consider the OTT Tornado machine we have for sale. Contact us for further details. Iodpfx Agezd U N Es Usth - Operating Hours: Approx. 7,900 hours (Calculated average from 2021-2026 following computer replacement in 2021)- Voltage: 3x400 VAC- Current: 31 A- Power: 19.5 KW- Frequency: 50 Hz- Control Voltage: 24 VDC- Max Fuse: 35 A - 5x6mm²- Edge Dimensions: Max. 65 x 2 mm / 55 x 12 mm- Panel Thickness: 8 - 60 mm (Up to 42 mm for premilling)- Panel Length: Min. 150 mm- Panel Width: Min. 70 mm- Control System: Panel Lodge System / Beckhoff 15" Color Touch Screen- Glueing System: CombiMelt Glueing System (Modular design for EVA and PUR hot melt, 1.5-liter hopper)- Premilling Unit: 2 HF motors (2.2 kW, 12,000 rpm) with diamond tools- Edge Magazine: For coiled edge material (0.4 - 3.0 mm) with automatic cutting device adjustment- Double End Trim Unit: 2 HF motors (0.3 kW, 12,000 rpm), automatic positioning 0°/3°- Rough Trimming Unit (Bfc): 2 motors (0.7 kW, 12,000 rpm)- Fine Trimming Unit: 2 HF motors (0.3 kW, 12,000 rpm) for radius 2-5 mm- Radius Scraper: Two-side tracing, automatic positioning with separate dust collection container- Corner Rounding System (KF-a): 2 HF motors, double-parallelogram guidance, max height 60 mm Technical Specification Feed Speed 14 m/min

Condition: ready for operation (used), Year of construction: 2017, overall weight: 3,800 kg, Edgebander manufactured in 2017. This HOMAG Optimat KDF 440 C features a workpiece thickness capacity of 8 - 60 mm and edge material compatibility of 0.4 - 8 mm. It offers a variable feed speed of 8 - 18 m/min and includes several units for joint trimming, glue application, and corner rounding. If you are looking to get high-quality edge banding capabilities, consider the HOMAG Optimat KDF 440 C machine we have for sale. Contact us for further details. • Condition: Used Itedpozdidaofx Ag Ujh • Workpiece thickness: 8–60 mm • Edge material: 0.4–8 mm (depending on unit configuration) • Feed speed: 8–18 m/min (variable) • Min. workpiece length: approx. 120 mm • Min. workpiece width: approx. 60 mm • Glue application: EVA hot-melt adhesive; PUR-compatible (optional) • Glue pot: Teflon-coated; quick-change capability • Total connected load: approx. 15–20 kW (depending on configuration) • Compressed air requirement: 6–7 bar • Control system: powerControl / powerTouch • CE marking: Yes • Unit configuration: • Joint trimming unit • Glue application unit • Pressure zone • End trimming unit • Top/bottom trimming unit • Corner rounding unit • Scraper unit • Buffing unit

Condition: ready for operation (used), Year of construction: 2000, overall weight: 2,000 kg, Edgebander manufactured in 2000. This OTT Pacific V6-F features an edge thickness capability of 0.2 - 6 mm and can handle workpiece thicknesses from 8 to 42 mm. It operates at a feed speed of 12 m/min and includes various processing units such as joining mills, a gluing unit, and a polishing unit. If you are looking to get high-quality edge banding capabilities, consider the OTT Pacific V6-F machine we have for sale. Contact us for further details. Used single-sided edge banding machineBrand: OTTType: Pacific V 6-FYear of manufacture: 2000Technical specifications:Edge thickness: 0.2 - 6 mmWorkpiece thickness: 8 - 42 mmWorkpiece width: min. 70 mmWorkpiece length: min. 150 mmFeed speed: 12 m/ctrical connection: 3 x 400V, 50 HzExhaust: 2 x Ø 120 mm at 20 m/aust capacity: 30 m³/hEquipment - Processing units:Joining mills2 x 1.5 kW, 12,000 rpm, 200 Hztwo application-controlled work spindlesGluing unitRapid-heating tank with Melt-maticautomatic edge magazine with optical monitoringfor strip edges in fixed lengthsRelease agent spray systemend trimming unit2 x 0.2 kW, 12,000 rpm, 200 Hzautomatic swivel 0° / 3°Flush milling unit 0° / 15° / 30° / 45°2 x 0.43 kW, 12,000 rpm, 200 HzRadius milling unit R2 - R52 x 0.3 kW, 12,000 rpm, 200 Hz2 quick-change stations for milling unitsCorner rounding milling unit2 x 0.3 kW, 12,000 rpm, 200 HzScraper2 x carbide scrapersPolishing unit2 x 0.2 kW, 2,800 rpm, 50 HzWeight: 2,000 kgNote:The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding. Ijdpjy Df Uujfx Ag Ujth

Condition: used, Year of construction: 1998, Used machine Year of manufacture: 1998 Proven quick heating tank; heating time approx. 5 minutes. Safety interlock for the application roller; the roller engages only after reaching operating temperature. Centrally height-adjustable upper pressure bar. Edge feeding and roll separation pneumatically controlled. Connected load: approx. 11.5 kW, heating power 4.5 kW, frequency inverter 300 Hz, 4 kVA. HF crosscut saw unit: electrically and pneumatically controlled, motor power 0.37 kW. Saw blade diameter: 100 mm HF flush milling unit: for radius, straight and chamfer milling. Crosscutting from rolls up to 3 mm. Edgebanding and crosscutting up to 5 mm. Minimum workpiece length: 260 mm Minimum workpiece width: 90 mm Workpiece thickness: Chamfer milling from 10 mm / radius milling from 13 mm / max. 45 mm Iodpew Tfw Hjfx Ag Ueth Extendable workpiece support at front. Digital position display for feed height adjustment, edge thickness, and milling. With chassis. With heated infeed ruler. Compressed air connection: 6 bar Central extraction port: 100 mm Dimensions (L x W x H): 3115 x 1230 x 1200 mm Approx. 560 kg Availability: short notice Storage location: Flörsheim

Condition: used, Year of construction: 2020, Used machine Year of manufacture: 2020 Features: - Aggregate control via touch-screen - Joint milling unit - Glue pot - End trimming unit - Radius milling unit Itodpfxox Enqus Ag Ueh - Radius scraper unit - Flat scraper unit - Buffing unit - Spraying unit (front and rear) Location: Rhineland-Palatinate Availability: By arrangement Sale on behalf of customer. Details provided without guarantee.

Condition: excellent (used), Year of construction: 2022, Manufacturer: BIESSE Model: AKRON 1440 A Category: Edge banding machine Year of manufacture: 2022 Availability: short notice Operational status: disassembled/stored Technical data Maximum edge banding thickness: 12 mm Maximum panel thickness: 60 mm Maximum thickness of roller material: 3 mm Minimum workpiece length: 140 mm Minimum workpiece width: 50 mm Minimum feed rate: 12 m/min Maximum feed rate: 18 m/min Feed rate: stepless Height adjustment: motorized Belt overpressure Gluing system: granulate Glue reservoir: top Quick-change glue reservoir Suitable for PUR adhesives Strip magazine Spraying device Edge trimming unit Preheating zone Pressure zone, NC-controlled Miter saw unit: 2 motors Itsdjzb Aicepfx Ag Ujh Edge trimming/radius/chamfer stations: 1 Corner copying unit: 2 motors Pulling blade unit Profile pulling blade, flat pulling blade Smoothing unit Nesting equipment Edge trimming/radius/chamfer stations, profile pulling blade Units controlled by timer NC axis(es) Profile change: automatic Edge trimming/radius/chamfer stations Design: left-hand machine Machine length: 5,610 mm Control system: BIESSE SMART TOUCH 23" Conformity marking: CE marking, EAC marking Total connection: 13 kW Weight approx.: 2,250 kg Location: at customer's site - available immediately - As it is disassembled/stored.

Condition: ready for operation (used), Year of construction: 2017, overall weight: 1,650 kg, product length (max.): 4,168 mm, Edgebander manufactured in 2017. This BIESSE Jade 240 features a panel thickness capacity of 10-60 mm and an edge height range of 14-64 mm. It includes a pre-milling unit, glue application unit, and various trimming units for enhanced functionality. If you are looking to get high-quality edge banding capabilities, consider the BIESSE Jade 240 machine we have for sale. Contact us for further details. • Technical data: • Panel thickness: 10–60 mm • Edge height: 14–64 mm • Edge thickness (coil): 0.4–3 mm • Edge thickness (solid strips): up to 8 mm • Feed speed: 12 m/min • Minimum workpiece length: 150 mm • Minimum workpiece width at 150 mm length: 85 mm • Minimum workpiece width at 250 mm length: 50 mm • Pneumatic connection: 7 bar • Glue pot capacity: approx. 2 kg • Glue pot heat-up time: approx. 10 min • Dust extraction connections: 100 mm • Standard units: • Pre-milling unit • Glue application unit Iodpfxjzc R E Us Ag Ueth • End trimming unit • Flush/profile trimming unit • Corner rounding unit • Radius scraping unit • Glue joint scraper • Buffing unit

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Very well-maintained machine Equipment: - Machine table with 13 running rollers for improved workpiece guidance - Edge feed, synchronized with the belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with blade (for cuttable edges) - Three pressure rollers - Belt feed 0.25 kW; approx. 1250 mm long; approx. 6.0 m/min; 50 mm wide toothed belt with thick, workpiece-friendly rubber cover. Digital counter for height adjustment - Direct glue application to the workpiece: leak-proof glue pot with glue reservoir from below and fast heat-up time after machine downtime - Flush-trimming unit for workpiece front and rear edge, automatic scanning on the workpiece, pneumatic trimming with blade for cuttable edges Itodezc Agkopfx Ag Ush - Flush-milling unit with vertical tracking and horizontal guidance, reproducible settings via digital counters, 2 powerful 0.4 kW high-frequency motors, infinitely variable from 4,000 to 18,000 rpm, cutter Ø 70 mm, Z4, radius 2 mm/15°; central extraction port Ø 100 mm, 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper milling cutter with the belt feed - Continuous workpiece support approx. 1800 mm long, workpiece support rail extendable by approx. 300 mm - Rotatable film disc Ø 800 mm Technical details: - Minimum workpiece width approx. 80 mm - Workpiece thickness 10 – 50 mm - Minimum workpiece length approx. 220 mm - Edge thickness 0.4 – 2.0 mm - Roller separation max. 1.0 x 55 mm, 2 x 45 mm - Heating capacity glue pot 2.7 kW - Electrical connection 400 V, 50 Hz, 3Ph + N - Total connected load 3.8 kW - Heat-up time approx. 10 minutes - Pneumatic connection 6 bar - Working height approx. 880 mm - Dimensions approx. 1800 x 700 x 1300 mm without film disc Ø 800 - Net weight approx. 260 kg Availability: short notice Location: Flörsheim

Condition: excellent (used), Year of construction: 2012, functionality: fully functional, power: 16 kW (21.75 HP), input voltage: 400 V, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 6 mm, feed rate X-axis: 11 m/min, total length: 4,150 mm, overall weight: 1,350 kg, year of last overhaul: 2026, Equipment: CE marking, documentation/manual, Brandt-Homag KDF 220 Highflex edge banding machine, year of manufacture 2012 from a small carpentry business Last inspection: March 20, 2026 Type: KDF 220 Machine number: 0-261-20-6136 Wiring diagram number: 0-261-20-6136 Year of manufacture: 2012 Supply voltage: 400Y/230 Units controlled via the display Gluing unit: 2 x 2.2 kW Trimming saw unit: 2 x 0.18 kW Flush trimming unit: 2 x 0.27 kW Profiling milling unit: 2 x 0.35 kW WD 40 -additional function: structural base Radius draw knife Itsdezdb Ivopfx Ag Ueh Straight draw knife Edge thickness: 0.4 - 6 mm Fsbq Uvmsyy S Ade Rnjph Workpiece thickness: 8-60 mm Feed rate: 11 m/min Total power: 16 kW Length: 4150 mm If you have any questions or require further information, please feel free to send us a message or call us.

Condition: excellent (used), Year of construction: 2000, Technical data: • Manufacturer: Hebrock GmbH (Made in Germany) • Type: EURO 2000 Itsdpfszbyvaex Ag Ush • Year of manufacture: 2000 • Voltage: 230 / 400 V • Frequency: 50 Hz • Power: 7 kW • Current consumption: 13.6 A Working range: • Workpiece thickness: approx. 10 – 50 mm • Edge thickness: approx. 0.5 – 3 mm • Minimum workpiece length: approx. 250 mm • Minimum workpiece width: approx. 70 mm • Feed rate: approx. 10 m/min • Compressed air connection required (approx. 6–7 bar) Location: in stock at warehouse 54634 Bitburg - immediately available -

Condition: ready for operation (used), Year of construction: 2009, Edgebander manufactured in 2009. This IMA Novimat/I/680/650/R3 features joint milling, a gluing section, and a pressure zone. It also includes trimming, flush milling, a multi-profile milling unit, and a sanding unit. If you are looking to get high-quality edge banding capabilities, consider the IMA Novimat/I/680/650/R3 machine we have for sale. Contact us for further details. • Technical features: • Joint milling • Gluing section • Pressure zone • Trimming • Flush milling Iedezcxlcepfx Ag Ueth • Multi-profile milling unit • KFA unit • Multi-profile scraper • Surface scraper • Sanding unit • 2 NC-controlled grooving units Additional equipment • Workpiece return

Condition: good (used), Year of construction: 2010, machine/vehicle number: 0 - 251 - 20 - 4507, functionality: fully functional, Due to a switch to solid wood processing, this machine has been used very little and is in good condition. Available for viewing in the workshop. Isdexzp Uwopfx Ag Usth

Condition: used, Year of construction: 2011, Used machine Year of manufacture: 2011 Condition: Machine completely overhauled and serviced Equipment and technical specifications: Infinitely variable feed speed: 10–18 m/min Edge Control 19 control system with 18.5" touchscreen color display Jointing milling unit Edge feeding Cartridge adhesive application station with sensing nozzle and automatic glue height adjustment Pressure unit End trimming unit Multifunctional milling unit Iodpfx Aewka N Teg Ujth Corner copying unit Radius scraper unit Surface scraper Buffing unit Workpiece thickness: 6–60 mm Edge thickness: 0.4–8 mm Minimum workpiece width: 60 mm Shortest workpiece length: 180 mm Dimensions: 5300 x 1500 x 1600 mm Weight: 2,200 kg Location: 65439 Flörsheim Availability: short notice

Condition: used, Year of construction: 2008, Used machine Year of construction: 2008 Edge thickness PVC: 0.4 - 2.0 mm Panel thickness: 10-45 mm Edge banding from roll automatic cross-cutting unit Flush trimming unit for flush and radius milling, r = 2 mm Motor 0.37 kW - 9000 rpm Extraction connection: 2 x 60 mm Heating capacity approx. 1150 W Total power 2 kW Weight approx. 240 kg Itedpjxppwbjfx Ag Ujh Dimensions 2040 x 1240 x 1260 mm Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 1989, Used machine Year of manufacture: 1989 Condition: Function tested Equipment and technical data: Max. edge thickness: 20 mm Max. edge height: 51 mm Max. thickness of coil material: 3 mm Min. workpiece length: 140 mm Min. workpiece width: 60 mm Glue system: 1906 cartridge Pressure unit Milling unit 1920 for flush milling up to 20 mm and chamfer milling Required space (LxWxH): 3150x1800x1375 mm Weight approx.: 800 kg Location: Flörsheim Availability: Short-term Itedpow I U E Aefx Ag Uoh

Condition: used, Year of construction: 2008, Used machine Year of manufacture: 2008 Itedpfow Nadgex Ag Ush Condition: currently still in production Features and technical specifications: Edgebanding max. 8-55 mm Incl. swiveling control panel HF jointing unit with 2 motors Incl. quick-heating, exchangeable, Teflon-coated glue pot Incl. electronic positioning of pressure rollers Incl. tilting double end-trim saw unit Incl. flush milling unit Incl. application-controlled chamfer, radius, and corner copying unit with nesting package Incl. radius scraper with nesting package Incl. surface scraper Incl. grooving unit Incl. buffing unit Incl. spraying unit Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2009, Used machine Year of manufacture: 2009 Single-sided automatic edge banding machine with CNC control, 10" touch screen Industrial conveyor chain 1 1/4" Joint milling unit FI-502 Glue application unit VC-710 End trimming unit IN-801 Top and bottom flush trimming unit RS-100 2 motorized multifunction profiling units - contour milling unit CR-202 (FAST system with 4 standard positions) Scraper unit RBK-503, NC 2 positions Flat scraper RCC-701 Workpiece thickness: 10-65 mm Max. workpiece height with contour milling unit (depending on profiles): 35-65 mm Edge thickness from roll: 0.4-3 mm Edge thickness from strip material: 0.4-22 mm (depending on unit) Minimum workpiece length: 140 mm Minimum workpiece width (with length 140 mm): 85 mm Minimum workpiece width (with length 250 mm): 50 mm Feed speeds: 10-14-18-20 Central extraction connection: 200 mm Extraction connection, edge banding: 80 mm Extraction connection, joint milling: 120 mm Glue pot capacity: approx. 3 kg Heat-up time at half fill: approx. 10 min Length: 6000 mm Iodpfx Agev R Nk Us Ujth Width: 1780 mm Height: 1770 mm Machine is offered without the workpiece return unit shown in the pictures Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2010, Used machine Year of manufacture 2010 With joining unit and corner rounding unit Control panel with LCD display and keypad Joining unit with 2 counter-rotating diamond cutters With edge feeder for roll and strip material With glue roller and glue unit With pre-trimming from the roll With pressure unit With trimming unit with pulling trimming cut With flush and radius trimming unit Corner rounding unit for front edges Manual unit adjustment Edge thickness 0.4-5 mm Workpiece height 8-60 mm Min. workpiece width 70 mm Min. workpiece length 140 mm Feed speed 11 m/min With radius scraper unit With flat scraper With polishing unit Extendable workpiece support Itjdpfew I H Rkox Ag Ueh Extraction connection 120 + 2 x 80 mm Weight approx. 990 kg L x W x H 4550 x 1550 x 1100 mm Availability: Short-term Storage location: Flörsheim

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Condition: Good (the machine has undergone extensive maintenance every year, most recently in March 2026!) Equipment: - iTronic – Adaptive pressure and glue quantity control with automatic, program-dependent fine adjustment - MOT SPS adjustable infeed fence - Automatic chain lubrication: Intelligent automatic transport chain lubrication - Edge Control 19 control system - EL GRM variable, 400V 50Hz, 2.2kW V2 SPRINT 1329 PERFORMANCE 400V 50Hz - Edge Control 19 control system with 18.5" touchscreen color display, 16:9 format Ijdoy Hyl Tspfx Ag Ueth - ECO MODE energy-saving mode: An automatic standby circuit - Jointing unit 1802 (2 x 2.0 kW, 200 Hz, 12,000 rpm) with 2 milling units for jointing panel edges - Diamond cutter, Ø 70 x 64 x 30 mm, Z2+2, left-hand rotation, Air Stream System (HOLZ-HER / LEUCO Patent) - Diamond cutter, Ø 70 x 64 x 30 mm, Z2+2, right-hand rotation, Air Stream System (HOLZ-HER / LEUCO Patent) - Edge feed 1901 SYNCHRO: automatic transport of coil and strip material - Glue application station Glu Jet GJ301 automatic (2.3 kW, 50 Hz) - DW501 SPS motorized SPRINT - GM501 spray device after the printing unit with lubricant (recommended for high-gloss edges) - End trimming unit 1918 (60 mm) pneumatic (2 x 0.45 kW, 12,000 rpm) pneumatically tiltable 0/10° - Milling unit FR701: 100% repeat accuracy at the push of a button due to backlash-free mechanics - Air Stream System multi-cutter, diamond Ø 70.9 x 16 mm, Z = 2+2 - Form milling unit FF701: 100% repeat accuracy at the push of a button due to backlash-free mechanics - Diamond cutter, Ø 72.5 mm x 19 mm, Ø 20 mm Z = 4, radius R = 2 mm, left-hand rotation with CM technology - Diamond cutter, Ø 72.5 mm x 19 mm, Ø 20 mm Z = 4, radius R = 2 mm, right-hand rotation with CM technology - Scraper unit 1929 MOT4 incl. high-gloss package with motorized adjustment of the tracing rollers - HW reversible knives for scraper holder, R = 2.0 mm (2 pcs. required) - Flat scraper FK701 with pre- and post-sensing for removing adhesive residue - TR501 spray unit for infeed and outfeed (separating and cleaning agent) - Includes nesting shoes below with their own spray unit Location: Hesse Availability: Approx. July 2026

Condition: used, Year of construction: 2001, Workpiece thickness min./max.: 6/45 mm Iedpfey Dd Iyjx Ag Uoth Edge banding thickness: 0.4 - 3 mm Edge banding height max.: 51 mm Edge banding strip length min.: 350 mm Edge banding overhang in height per side max.: 3 mm Workpiece width min.: 60 mm Workpiece length min.: 180 mm Overall length: 3700 mm Width: 1440 mm Height max.: 1970 mm Workpiece infeed height: 850 mm Weight: approx. 850 kg Storage location: Nattheim

Condition: new, Year of construction: 2025, The Hebrock F 5 If you want maximum performance, the Hebrock F 5 is the solution for edgebanding in demanding craft operations. The F 5 guarantees edgebanding in all steps, as it is equipped with all the components you need to meet your requirements: Joint trimmer, cross-cut saw, trimming unit, radius scraper, corner trimmer, surface scraper, fettling station. For even more flexibility on the way to the perfect finish, the F 5 can be optionally equipped with a practical multi-radius scraper. max. edge thickness: 3 mm Max. workpiece thickness: 50 mm Ready for operation in 3.5 min Equipment: Hebrock F5 Next - 10 m/min Edge banding machine F5 Next With PLC control (incl. touchscreen) and with hot-melt glue application to the workpiece for edgebanding material up to 3 mm; jointing cutter (incl. slide tool) up to 2 mm cutter depth, maintenance-free glue tray with change tray pre-equipment incl. glue discharge device, HF cross-cut saw station (approx. 12000 rpm), HF trimming station (approx. 12000 rpm) with separate pneumatic routing adjustment and exchangeable panel router (combination version), corner rounding router, radius scraper, surface scraper (incl. pneumatic lift), cleaning station, robust chain drive, ball bearing mounted double roller top pressure, viewing window from the rear of the machine, extendable workpiece support, feed rate approx. 10 m/min. F5/08/4 Quick-change attachment for corner router F5/08/5 additional exchangeable motor corner router with tool assembly F5/09/4 Multi-radius scraper (R1/R2) F5/24/1 Spraying device for release agent F5/24/2 Spraying device for cleaning agent F5/25 Edge spraying device Itsdpfxslht Hwe Ag Uoh F5/27. nesting for router and radius scraper F5/30. Pneumatic 3-point adjustment (radius, chamfer, flush trimming) Location: From stock 54634 Bitburg - available in CW4 -