Used Servo for sale (3,375)

Condition: used, Linear unit, linear axis, gantry axis with servo drive, synchronous servo motor, electric slide, loading unit, linear guide with servo motor and pneumatic gripper REXROTH INDRAMAT Type: MKD0771B-061-KP1-KN Ident No. 247238 0001 Year of manufacture: 2000 Axis movement: 2400 mm Carriage length: approx. 500 mm Total length: 3520 mm - Pneumatic feed gripper (clamping gripper with 2 Festo compressed air cylinders) - Standard linear guide 65 x 25 mm - Steel base profile - Ball screw Ø 32 x 10 mm - pneumatic with position indicator Gsdogi E Haepfx Adbsbi - Permanent servo motor type: MKD071B-061-KP1-KN (Part no.: 261989, p. no. MKD071-50234, brake with 24 V DC) Overall dimensions L x W x H: 3520 x 400 x 580 mm Weight: 340 kg good condition possible drive controllers under stock no. 53628 and stock no. 53673

Condition: used, 6-axis robot servo controller, drive, motion control, servo pack, servo unit Servo unit for YASNAC XRC UP6 YASKAWA / MOTOMAN type CACR-UP6AAC Gsdpfx Adewywi Aobjbi O/N RA8616-0Y4A-46 S/N: D000Z2676590046 Version: 6-axis module for robot - Suitable for YASKAWA / MOTOMAN / YASNAC XRC UP6 - USB interface - Power supply type JUSP-RCP01AAC Dimensions (W x H x D): 270 x 310 x 200 mm Weight: 8.5 kg Used, in very good condition

Condition: used, Transistor pulse inverter for three-phase feed drives with analog control, servo controller SIEMENS type Simodrive 610 6SC6101-3A-Z Fab. No.: A 822M103 Z = A30+A20+A18 Year of manufacture: 1989 The Simodrive 610 transistor pulse inverters have been developed to supply the 1FT5/1FS5 three-phase servo motors. The dynamic characteristics of these motors are to be used optimally. The pulse inverters can be used for a wide variety of tasks by equipping the power section accordingly. This flexibility is further increased by expansion modules for the power section. Supply voltage: 3 AC 50/60 Hz 165 Volt or DC 220 Volt (suitable transformer: 380/165 Volt 5kVA (not included in delivery) Output voltage: 3 UC 200 Volt Efficiency: approx. 95 Number of feed axes: 4 Speed reference: +-10 volts Auxiliary voltage: 24 volts Relay contact for messages fault/ready for operation dimension WxHxD: 339 x 440 x 300 mm Weight: approx. 25 Kg Gbedpfx Adjh D Syvjbsi The servo drive is still ready for operation in a Gildemeister GDM42. Further components from the Gildemeister you will find under stock numbers: 60343, 60347, 60348

Condition: used, 6-axis AC servo drive, servo controller, servo inverter, servo amplifier, servo regulator, frequency converter, drive controller for robots FANUC type A06B-6105-H003 No. V07Z08282 Gbodpfx Adjkpwu Rjboi NEW / unused Input voltage: 200 - 240 VAC Rated power: 1.5 kW Number of axis outputs: 6 Output current: 6 x 13 A Total output current: max. 78 A Manual No.: B-81465 Standard: EN50178 Installed PCBs: A16B-2000-0063/07D, A16B-3200-0440/05C - Plexiglass cover not included in delivery Dimensions (W x H x D): 70 x 170 x 380 mm Weight: 16.5 kg As new / unused in opened original box from stock liquidation

Condition: used, 2-axis removal machine, inserter, servo robot, workpiece gripper, pick-and-place machine, removal robot Removal device, handling device for presses, lathes, etc. GETECHA Type GL-20S No. 13836 Year of manufacture 10/2003 Z-axis travel 1900 mm Travel distance Y-axis 250 mm Travel speed Z-axis max. 1100 mm/sec. Travel speed Y-axis max. 227 mm/sec. infinitely variable travel speed in Y- and Z-axis via SMB servomotors - precise axis movement via linear guides - epis control system - Control panel opposite Gbodpfeharwyex Adbji - Control for conveyor belt, gripper magnets, bead breaker cylinder, vacuum, gripper - External monitoring inputs for emergency stop, press open, press closed, safety doors closed, automatic - Mounted gripper with 3 lifting magnets, 3 pneumatic push-off cylinders (30 mm stroke), 1 pneumatic clamping cylinder (40 mm stroke) - Operating hours 25998 hrs. The system was used as an inserter/removal device on a press. Space requirement L x W x H 2900 x 1800 x 2000 mm Weight approx. 800 kg good condition

Condition: used, Drive motor, DC servo motor LENZE type GFQUBT 112-22 Spindle motor, electric motor Serial no. Godpfx Ajqv I S Sedbsbi 0239398K Year of construction: 1993 Rated power: 6 kW Operating voltage: 400 DC Rated current: 18 amps Maximum speed: 1000 rpm Excitation voltage: 210 VDC Excitation current: 3.4 amps Shaft diameter: 38 mm (shaft with 10 mm feather key) Shaft length: approx. 76 mm (shaft projection from centering edge) Centering flange diameter: 230 mm Bolt circle diameter: 264 mm, 4x 14 mm holes Longlife speedometer HÜBNER type TDP 0.2 LT-4 Speedometer voltage: 60V / 1000 rpm Speed max. 9000 rpm External fan LENZE type GSD 160 Mains connection: 400 V, 50 Hz. 0.32 kW Overall length: 830 mm (without shaft and centering flange) Overall dimensions L x W x H: 920 x 300 x 460 mm Own weight: 130 kg good condition

Condition: used, Permanent magnet DC servo motor SIEMENS Type: 1 HU3074-0AC01-Z NO.B J157 1047 01 008 Voltage = 167 Volt DC = direct voltage Power = 1.8 kW Current consumption = 12.5 amps Speed = n. max.: 2000 rpm Rated torque = Mo 7 Nm Gbedpeuch N Iefx Adbji Shaft diameter 24 mm Stub shaft length 50 mm Centering diameter 130 mm Bolt circle diameter 165 mm / 4 x 11 mm holes - Shaft with 8 mm keyway Housing dimensions L/W/H 335 x 140 x 145 mm Weight: 23 kg good condition

Condition: used, Miter cross-cut saw for aluminum (special machine construction with 4 servo motors) Circular saw, miter saw, rip saw year of construction 2002 Saw blade diameter 500 mm Sawing range at 90° round Ø 180 Rectangle 350 x 140 mm (through longitudinal cut) Sawing range at 45° round Ø 180 Rectangle 350 x 100 mm (through longitudinal cut) Guide length of base support 1100 mm Travel on the base support (forwards and backwards) 650 mm Travel on the stand (up-down) 120 mm Saw blade speed approx. 3000 rpm Motor power 2.2 kW Mains connection 400 Volt, 50 Hz - Controlled longitudinal cutting movement - Controlled saw blade height adjustment - Controlled mitre cut through swivelling saw unit - Controlled miter cut by tilting saw unit - Pivoting and tilting of the saw via INDRAMAT servomotors with precision gears (MKDO71B-061-KG1-KN and MKDO41B-144-KP1-KN motor) - Vertical axis movement via INDRAMAT servomotors and ball screws (MKDO41B-144-KP1-KN motor) - a total of 4 Indramat servomotors are installed - very good German mechanical engineering Space requirement L x W x H 1150 x 1100 x 1400 mm weight approx. 360 kg good condition Gjdpfodzp T Djx Adbebi The unit comes from a special machine for special products. All other components and electrical parts for the construction of a new special machine are also available.

Condition: good (used), Servo motor, electric motor, DC motor, stepper motor, stepper motor -Manufacturer: Nucleus, servomotor -Type: NUDrive MP42 2A Size 42 R Rev.2 IP64 -Item No.: DS421106 -Shaft: Ø 14 x 35 mm -Number: 2 servo motors available -Price: per piece -Dimensions: 134/42/H56 mm Gjdpfx Adjyh Axnobsbi -Weight: 0.6 kg/pc.

Condition: good (used), Servo motor, electric motor, DC motor, stepper motor, stepper motor -Manufacturer: Nucleus, servomotor -Type: NUDrive MP57 2A IP64 -Item No.: DS421107 -Shaft: Ø 10 x 30 mm -Number: 2 servo motors available Gbodpfoxt D Atsx Adbsi -Price: per piece -Dimensions: 155/56/H70 mm -Weight: 1.3 kg/pc.

Condition: good (used), Servo motor, electric motor, DC motor, stepper motor, stepper motor -Manufacturer: Nucleus, servomotor -Type: NUDrive MP85 10A Bgr2 R Rev2 IP64 -Item No.: DS851028 Gedpfx Aeyh Aq Djdbobi -Shaft: Ø 14 x 35 mm -Number: 2 servo motors available -Price: per piece -Dimensions: 200/85/H110 mm -Weight: 3.5 kg/pc.

Condition: good (used), Servo motor, electric motor, DC motor, stepper motor, stepper motor Manufacturer: Nucleus, servomotor -Type: NUDrive MP85 10A Bgr2 R Rev2 -Item No.: DS851026 -Shaft: Ø 14 x 37 mm -Number: 11 servo motors available Gbodpsxr Agnsfx Adbji -Price: per piece -Dimensions: 200/85/H85 mm -Weight: 4.1 kg/pc.

Condition: used, mileage: 60,000 km, power: 124 kW (168.59 HP), first registration: 12/1974, overall weight: 11,000 kg, fuel type: diesel, color: red, axle configuration: 2 axles, next inspection (TÜV): 12/2026, gearing type: mechanical, loading space width: 2,450 mm, loading space length: 4,680 mm, loading space height: 1,450 mm, Year of construction: 1974, total width: 2,470 mm, total height: 3,050 mm, Equipment: all wheel drive, 1st hand. German fire truck with valid TÜV (general inspection) and SP (special inspection) until 12/2026. Regular registration valid until 18.02.2026. For 30 years (after its official service life), this vehicle has only been kept as a collector’s item in a hall, always regularly serviced, driven, and exceptionally well maintained by the fire department. In the meantime, it was transferred to the local airport. Bachert body in an aluminum-steel composite construction, extremely robust and built to last, with great attention to detail. The heavy-duty roller shutters and flaps are all still working perfectly. The 1113 starts immediately and is ready to drive. Good original condition. There are signs of use from over 50 years of firefighting service. No serious defects or significant rust damage are visible on the vehicle. Overall, a solid round-hood model. LAF 1113 B with 3 windshield wipers. Power steering. OM 352 A 6-cylinder diesel engine with turbocharger and just under 170 hp. 85 km/h is registered as the top speed in the papers. 5-speed manual transmission. PTO (power take-off). Hydraulic system for auxiliary equipment. Selectable 4x4 all-wheel drive. Wheelbase: 4200 mm. 3 seats. Large Rockinger trailer coupling with air connections and 10,000 kg braked towing capacity. Maximum unbraked towing capacity is 1,500 kg. RW2 rescue vehicle body with winch, power generator, and light mast. Winch: Rotzler 5 tons with 65 m steel cable. Power generator: Knurz-Kirsch 20s. Output: 20 kVA. Light mast at the left rear, hydraulically extendable. Roof is accessible via rear ladder, with aluminum checker plate, and two large storage boxes. Overall vehicle dimensions: 7300 mm long / 2470 mm wide / 3050 mm high. Box body dimensions (external measurement) approx.: 4680 mm long / 2450 mm wide / 1450 mm high. Tires: 8.25-20/14 PR, apparently without DOT marking, not porous and in good condition. The 1113 was previously registered as “Other Vehicle – Fire Brigade – Rescue Vehicle”. Gjdpsyndg Nsfx Adbebi Battery charging socket and manual battery disconnect switch on the driver’s seat console. The odometer was replaced in 2018 and now shows 141,000 km. The original odometer with 27,000 kilometers was retained and correctly handed over to us by the fire brigade. The actual total mileage is a maximum of 60,000 kilometers, in reality likely much less. As the inspection log has been continuously maintained with mileage figures for the last 25 years, both the mileage and the odometer replacement during this period can be reliably and continuously documented. In addition to the original odometer, there is a box full of original Daimler-Benz and Bachert documents, as well as paperwork such as logbooks and generator documentation, most of which are original documents from the year of manufacture 1974. Everything is in good and well-preserved condition. The documents are not for sale separately, nor will they be copied; please accept these facts as presented. Only the buyer of the 1113 will receive these treasures along with the vehicle from us. This offer is only for tradespeople, freelancers, authorities (BOS), public institutions, and all kinds of comparably self-employed businesses. Sale to private end users is, unfortunately, not possible. Interim sale and errors excepted at any time. Net price: €18,900!

Condition: new, Bernardo Universal Milling Machine UWF 110 Servo -1000 Technical specifications table size 1370 x 300 mm Spindle mounting ISO 40 mm spindle speed (11) 45 - 1660 rpm Travel lengthwise (x) 1000 mm traverse path cross (y) 360 mm Travel vertical (z) 400 mm Distance spindle / table 60 - 460 mm throat 95 - 575 mm Table can be tilted -45° to + 45 Max. workpiece weight workpiece weight 250 kg Feed range longitudinal / transverse (8) 30 - 830 mm/min Feed range vertical (8) 23 - 625 mm/min Rapid traverse x-, y- and z-axis 1000 / 1000 / 750 mm/min T-slots (number / width / distance) 3 / 14 mm / 80 mm Main motor 3,0 kW Gedpsg Hzbxofx Adbebi Servo motor (torque / power) 10 Nm / 1.5 kW Coolant pump power 60 W Coolant pump flow rate 12 l/min Machine dimensions (W x D x H) 1740 x 1860 x 1900 mm Weight approx. 1505 kg Scope of delivery - 3-axis digital display ES-12 H with LCD display - M16 tightening spindle - LED machine light - feed for x-, y- and z-axis - coolant device - counter bearing - Long milling arbor ISO 40 / 27 mm - Combination arbor ISO 40 / 27 mm - Coolant trough - Adjustable guard - Central lubrication for x-, y- and z-axis - Operating tool

Condition: as good as new (ex-display), functionality: fully functional, Year of construction: 2025, 6-axis servo press brake Press force 65 tons Bending length 2100 mm 4-axis backgauge (X, R, Z1+Z2) Delem DA66 Stroke 300 mm Installation height 590 mm Godpfx Adjxpfdkjbobi

Condition: good (used), Servo drive, power supply module, control unit, converter, controller, servo module, axis amplifier, DC converter, inverter, control module -Manufacturer: B&R, Processor Controller with bus base Gbedpfx Adeyhnb Djboi -Type: X20 CP 0483 -Bus base: X20 BB 52 -Dimensions: 100/40/H80 mm -Weight: 0.3 kg.

Condition: good (used), Year of construction: 2015, Servo drive, power supply module, control unit, converter, controller, servo module, axis amplifier, DC converter, inverter Gbedsyhmf Uepfx Adboi -Manufacturer: B&R, power supply module -Type: 80PS080X3.10-01 -Dimensions: 295/250/H70 mm -Weight: 3.5 kg.

Condition: used, Linear guide, portal axis SCHNEIDER ELECTRIC / FESTO Electric slide Motor type: ILS1B571PC1A0 Gbodjw Uc Tzspfx Adboi Year of manufacture: 2010 Axis travel: 300 mm Power supply: 36 Volt (DC) Carriage: 86 x 54 mm - Synchronous servo motor / stepper motor SCHNEIDER ELECTRIC, type: ILS1B571PC1A0 - Linear guide FESTO, type EGSK-33-300-6P - Ball screw Ø 10 mm, pitch 6 mm - 2 adjustable position sensors Dimensions L x W x H: 580 x 120 x 57 mm Weight: 6.5 kg in good condition

Condition: new, functionality: fully functional, Year of construction: 2025, coil width: 200 mm, product width (max.): 200 mm, overall weight: 80 kg, warranty duration: 12 months, working width: 200 mm, product height (max.): 3 mm, roll width: 64 mm, Silicon+ SFS 200 Servo Roll Feeder Compatible with all kind of presses, primarily used on Bruderer, Schaal and Mabu machines. Feeding length – min 0.10 mm to max. 9999.99 mm Feeding width – max. 100 mm, 200 mm or 300 mm. Depending of model required. Material thickness – 0.20 – 3.20 mm Feeding angle – 180° Die line height – ± 50 mm Max. feeding speed – 20 m/minute Strip release – Festo pneumatics Control – NC Touch screen Servo brushless motor – 0.75 KW, 1.8 KW or 2.3 KW. Weight approx. feeder: 80-150 kg. Feeder dimensions: 780 X 730 X 680 mm Godpevptz Ijfx Adbsbi – The unit is driven by the brushless servo motor, with direct drive transmission, eliminate the gear clearance, abrasion, no noise, no lubrication, safely to a synchronized pair of roller segments. – Rolls can be made upon request with PU surface for delicate raw material feeding. – Synchronization of the feeder and punching machine is done easy through cam signal from PLC of a punching machine. – Programmable feeding can be done for up to 10 groups of feeding pitches and saved as recipes. The feed length can be steplessly adjusted during operation EUR 1 certificate of European origin and CE compliance. This information is subject to change without notice, we can make personalized feeders for your needs with prior agreement.

Condition: used, Synchronous servomotor with holding brake and gearbox, geared motor, electric motor, angular geared motor Motor: Manufacturer: LUST LTI DRIVES Type: LSK-190-7-30-560 T1,P,KK,1R Order No.: 716090 Art. No.: 0970.8016 Machine type: Permanently excited synchronous servo motor DC link voltage of the controller Uzk: 560 VDC Rated power: 14.51 kw Rated speed: 3000 rpm Rated torque Mn: 46.2 Nm Standstill torque M0: 83.4 Nm Rated current In: 31.5 A Standstill current I0 / I0max: 54.9 / 219.6 A Pole pairs: 3 Shaft diameter: 32 mm Shaft length 50 mm - Shaft journal with key and keyway DIN 6885 / A10x8x50 - Option 1R Resolver 1-pole pair - Option KK Terminal box - Option T1 (DIN-PTC double base insulated) - Power connection 8-pin junction box - Resolver connection 12-pin junction box Holding brake: Manufacturer: LUST LTI DRIVES Type: NFH10-H/BA Order no.: 718690 Art. No: Rated voltage: 24 VDC Rated current: 4.5 A Rated power: 108 W Braking torque: 65 Nm Angular gearbox WESTFALIA Systemtechnik Gbodpfx Adef Dlzuoboi Hollow shaft output: internal Ø 65 mm Hollow shaft length: approx. 280 mm Gearbox output speed: max 450 rpm Speed gearbox input: max 4500 rpm. Transmission ratio: 10:1 - Shaft journals also ground on the outside - Gearbox can be mounted on two flange surfaces - Mounting hole on gearbox 180 x 180 mm / 180 x 230 mm Overall dimensions L x W x H: 1110 x 250 x 350 mm Total weight: 180 kg good condition

Condition: good (used), Basic - feed-in unit, feed-in module, inverter, frequency converter, frequency transformer, drive inverter, controller, variable speed drive -Type: BUS624-38/55-54-0-000 Gsdpeu Dcv Usfx Adbobi -Input: DC 540 V/640 V -Output: 3AC 360V/425V 3x38A 0-300Hz -Number: 4 servo power units available Price: per piece -Dimensions: 190/380/H300 mm -Weight: 14 kg

Condition: as good as new (ex-display), Year of construction: 2021, operating hours: 100 h, !! Parts in mint condition with warranty!! Price between €300-1000 each. Gedpfsucwzaox Adbsbi Over 40 motors and controllers available. A list of the items is available upon request. We would be happy to advise you!

Condition: new, Promess KA-EMF80 Servo Press 80 kN Godpfx Adsrgn Nnjbebi Manufacturer: Promess Type: KA-EMF80 Type: Servo Press KN: 80 Condition: New Calibrated: Yes Strain Gauge Amplifier: BA 624.u2 Financing through our bank is also available. komplett-konzept.leasingo.de Find more new and used servo presses in our shop! International shipping costs on request!

Condition: excellent (used), Bosch DM 4K 7101-D, servo module Amplifier module 1070079646-208 Gbjdpfxjk Szy Uo Adbsi Item condition: Used, in perfect condition Shelf(2)B-7_EK(BOR) Financing through our bank is also possible. komplett-konzept.leasingo.de More modules- new and used - you can find in our store! International shipping costs on request!

Condition: new, Year of construction: 2025, feed 2-22 m/min Weight 60 kg Gbedpfjvz E Uksx Adbei Total power requirement 0,4 kw