Used Turning Station for sale (11,772)

Condition: used, Year of construction: 2013, Mori Seiki NLX2500SY/700 Turning Centre with MAPPS IV/M730BM Control, Swing Over Bed 920mm, Max Swing Over Cross Slide 742mm, Max Turning Length 705mm, Main Spindle Kitagawa 10” dia Chuck at 4000rpm, Sub-Spindle Kitagawa 6” dia Chuck at 6000rpm, 12 Station Turret, High Pressure Coolant, Bar Feed Interface, Swarf Conveyor, Machine Weight 6,360kgs, Floor Space (L x W x H). S/No. NL254130936 (2013) Lhodpfsx Syahox Ahzeb Location: These lots are located in Tamworth, UK. Unfortunately there are no loading facilities on-site, dismantling and loading will be at the cost of the Purchaser. All/Any tooling is being offered as specifically described.

Condition: excellent (used), Year of construction: 2018, Nakamura-Tome NTRX-300 High Rigidity Multitasking Machine with NT Smart X Control, Halter Parts Loader & Fanuc Robot Ljdpfjx Iv Nqox Ahzjhb NT Smart X (Fanuc31i-Guide i). Maximum Turning Ø640mm. Maximum Turning Length 1,100mm. Distance Between Spindles Min/Max 250-1,350mm. Main Spindle- Buck BBC 210 3 Jaw Power Chuck. Maximum Spindle Speed 3,500rpm (22/18.5kW Motor). Spindle Nose A2-8. Bar Capacity Ø80mm. Sub Spindle- Kitagawa B-210 3 Jaw Power Chuck. Maximum Spindle Speed 3,500rpm (22/18.5kW Motor). Spindle Nose A2-8. Bar Capacity Ø80mm. Axis Travel 'X'=700mm, 'Z'=1,125mm, 'Y'= ± 125mm, 'B2'=1,100mm. Driven Tool (Milling) Maximum Spindle Speed 12,000rpm (22/15kW Motor). Swivel Range 225° (-120°/+105°). Spindle Taper Capto C6. 80 Position ATC. Maximum Tool Ø90/Ø120mm (Non-Adjacent Tool). Maximum Tool Length 300mm. Maximum Tool Weight 12kg. S/No. RX300709 (2018). Halter Load Assistant U-20 Parts Loader with HALTER Smart Touchscreen Control- 72 Workpiece Positions. Workpiece Diameter (Min-Max) Ø10-230mm. Minimum Workpiece (L x W) 10 x 10mm. Maximum Workpiece (L x W) 230 x 230mm. Maximum Height of Workpiece 250mm. Maximum Load Capacity Robot Arm 20kg. With Sick S30A-4011CA Safety Laser Scanner. S/No. DCH0203 (2019). Fanuc Robot M-20iA Type A05B-1225-B252- 6 Axis, Payload 20kg, Reach Approx 1,811mm. S/No. R18704467 (2018). With Renishaw Tool Setting Arm, Renishaw Tool Breakage Detection, Renishaw Spindle Inspection Probe, Coolant System With 8 Bar Through Spindle Coolant, Parts Loading/Unloading Conveyor With Schunk Spindle Parts Gripper, Tri-Mist 1000 Mist Extraction Unit, Daikin Inverter Oil Chiller, LNS Turbo MH500 Chip Conveyor, Parts Catcher, Foot Switches, Signal Tower, Handwheel & Built in Control Manuals. Overall Dimensions L4,460 x D2,670 x H2,615mm. Weight 18,000kg. Note: Tooling Not Included.

Condition: excellent (used), Year of construction: 2019, Nakamura-Tome NTRX-300 High Rigidity Multitasking Machine with Halter Parts Loader, Fanuc Robot & Hydrafeed Barfeeder With NT Smart X (Fanuc 31i-Guide i) Control. Maximum Turning Ø640mm. Maximum Turning Length 1,100mm. Distance Between Spindles Min/Max 250-1,350mm. Main Spindle- Buck BBC 210 3 Jaw Power Chuck. Maximum Spindle Speed 3,500rpm (22/18.5kW Motor). Spindle Nose A2-8. Bar Capacity Ø80mm. Sub Spindle- Kitagawa B-210 3 Jaw Power Chuck. Maximum Spindle Speed 3,500rpm (22/18.5kW Motor). Spindle Nose A2-8. Bar Capacity Ø80mm. Axis Travel 'X'=700mm, 'Z'=1,125mm, 'Y'= ± 125mm, 'B2'=1,100mm. Driven Tool (Milling) Maximum Spindle Speed 12,000rpm (22/15kW Motor). Swivel Range 225° (-120°/+105°). Spindle Taper Capto C6. 40 Position ATC. Maximum Tool Ø90/Ø120mm (Non-Adjacent Tool). Maximum Tool Length 300mm. Maximum Tool Weight 12kg. S/No. RX300808 (2018). Halter Load Assistant S-230-20 Parts Loader with HALTER Smart Touchscreen Control- 12 Position Stacker. Workpiece Diameter (Min-Max) Ø43-230mm. Maximum Height of Workpiece 175mm. Maximum Load Capacity of Robot Arm 20kg. Maximum Total Weight on Rotating Table 1,250kg. Maximum Stacking Height 350mm. Number of Stacking Stations (1 Empty) 12. Maximum Weight Per Station 115kg. With Sick S30A-4011CA Safety Laser Scanner. S/No. DCH0300 (2019). Fanuc Robot M-20iA Type A05B-1225-B252- 6 Axis, Payload 20kg, Reach Approx 1,811mm. S/No. R18Y00642. Hydrafeed Multifeed Barfeeder Length 2,100mm. S/No. 6849. Lsdpfox Iv H Nsx Ahzjhb With Renishaw Tool Setting Arm, Renishaw Spindle Inspection Probe, Coolant System With 8 Bar Through Spindle Coolant, Parts Loading/Unloading Conveyor With Schunk Spindle Parts Gripper, Daikin Inverter Oil Chiller, LNS Turbo MH500 Chip Conveyor, Parts Catcher, Foot Switches, Signal Tower, Handwheel & Built in Control Manuals. Overall Dimensions L4,460 x D2,670 x H2,615mm. Weight 17,000kg. Note: Tooling Not Included.

Condition: used, Year of construction: 2013, Mori Seiki NTX2000/1500SZM 5-Axis Mill/Turn with F31iB5 Control, Main Spindle Kitagawa 10”dia Chuck at 4,000rpm, Sub-Spindle Kitagawa 10”dia Chuck, 76 Position ATC, 10 Station Indexing Turret, Spindle Taper Capto C6, SMW SLU 3.2 Hydraulic Steady, High Pressure Coolant, Swarf Conveyor. S/No. NTX20130611 (2013) Location: These lots are located in Tamworth, UK. Unfortunately there are no loading facilities on-site, dismantling and loading will be at the cost of the Purchaser. All/Any tooling is being offered as specifically described. Lhodpfox R Uc Ujx Ahzsb

Condition: good (used), Year of construction: 2005, Daewoo Puma TT 2000SY Twin Turret Turning Centre with Fanuc 18i-TB CNC Control With Hydrafeed Multifeed MX-1B Short Magazine Automatic Bar Feed. Swing Over Bed 800mm. Swing Over Saddle 620mm. Max Turning on Upper Turret Ø390mm. Max Turning on Lower Turret Ø300mm. Max Working Length 350mm. Max Bar Ø65mm. 'X1' Axis Travel 255mm, 'X2' Axis Travel 190mm. 'Z1' Axis Travel 800mm, 'Z2' Axis Travel 900mm. 'Y' Axis Travel 120mm (+ or - 60mm). 'B' Axis 810mm. 'C' Axis 360°. (1) Kitagawa BB08 Power Chuck Ø210. (1) CRS66 Power Collet Chuck, Gripping Range 4mm-66mm. Main Spindle Nose A2 No.6 with Ø76mm Through Hole & Ø66mm Bore of Draw Tube & Max Speed of 5,000RPM. Twin Turret each with (12) Tool Stations. Tool Size 25mm x 25mm, Boring Bar Size Ø40mm & Spindle Speeds 4,000RPM. LNS Turbo 62878680E Swarf Conveyor (2005). Puma S/No. PT 20SY0047. Hydrafeed Multifeed MX-1B Automatic Bar Feed. Approx Ø3 - Ø80mm x 1,250mm Long Bar Range with Hydrafeed Controller, S/No. 202618. Includes Probe Arm, Signal Tower, (2) Machine Lights & (2) KF-101P Foot Switches. Dimensions of Turning Centre Approx 4,100mm x 2,300mm x 2,600mm High, Weight Approx 11,600kg. Please note: Filtermist FX 4000 XCEL 2 Oil Mist Filter Extraction is not included with the machine. Ledpfx Aox H Thbehzehb

Condition: used, Year of construction: 2017, DMG Mori NLX2000SY/500 CNC Turning Centre. Serial No. NL203171121 (2017) with Siemens Ergoline Celos Type 9CE000_APDB Control, 20 Station Turret, Kitagawa BR08 Large Bore Main Spindle 3-Jaw Chuck & Kitagawa B208 Sub-Spindle 3-Jaw Chuck, Main & Sub-Spindle Toolsetters, Parts Catcher, Parts Conveyor, Hydrafeed Multifeed MX1B Bar Feed, Cleanmist CM1400/2, Swarf Conveyor, Selection of Driven & Static Tool Holders with Capto Turning/Boring Tools, Manuals, Setting Bar, Country of Origin: Japan Please Note: This machine has been decommissioned and transit brackets fitted. Location: This lot is located in Birmingham, UK. A charge of £550 for dismantling and loading onto suitable transport will be automatically added to your invoice should you be successful in purchasing this item. Blocking and securing will be at the cost of the purchaser. All/Any tooling is being offered as specifically described. Ledex R Tctopfx Ahzehb

Condition: used, This listing is for a Thermo scientific Shandon HyperClean 1 Grossing Station Lodpsxzh Ezofx Ahzehb

Condition: used, Year of construction: 2019, Control: MITSUBISHI M730UM with CELOS Main spindle with integrated motor spindle ISM 80: 15/18.5 kW Speed range: 10–4000 rpm 10" hollow chuck 254mm KITAGAWA BB210A821 Counter spindle with integrated motor spindle ISM 65 Speed range: 10–5000 rpm 10" hollow chuck 254mm KITAGAWA BB208A621 20-position BMT star turret KNOLL high-pressure coolant system 70 bar Y-axis with 100mm travel Lhsdpfxeycukhe Ahzeb Gantry loading system LG-10AI

Condition: used, Year of construction: 2008, functionality: fully functional, Turning / milling center with counter spindle with 10 CNC axes (X1, X2, Z1, Z2, Y1, Y2, B1, B2, C1, C2) Control: FANUC 31:iA Lhsdpfx Aeycuikohzsb Main Spindle Power: 15/11 kW bar material dia.: 51 mm spindle revolution: 5.000 min-1 Counter Spindle Power: 11/7,5 kW bar material dia.: 51 mm spindle revolution: 5.000 min-1 Turning and milling spindle Power: 7,5/3,7 kW Turning and milling spindle speed: 12.000 min-1 max. rotation length turret bottom: 1.005 mm Slide cross X1 / X2 / Z1 / Z2 / B2: 455 / 222,5 /1.090 / 1.005 / 1.008 mm Slide cross Y1 / Y2: +/- 70 / +20, -50 mm Swivel range B1 axis: +/- 95 ° Linear rack magazine incl. support robot CNC support steady rest Coolant cyclone filter system incl. 2 pcs. coolant pumping spindle oil cooler

Condition: good (used), Year of construction: 2007, operating hours: 88,040 h, functionality: fully functional, machine/vehicle number: 07400003691, turning diameter: 120 mm, spindle bore: 118 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 30 m/min, total height: 2,500 mm, total length: 5,500 mm, total width: 2,500 mm, overall weight: 11,000 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D POWERLINE, DMG GILDEMEISTER TWIN 102 CNC Turning and Milling Center - Recorded spindle hours: 43,558 - Spindle speed range: 3,200/5,000 rpm - Swing diameter: 270 mm - Spindle distance: 900 mm - X1 axis travel: 290 mm - Z1 axis travel: 650 mm - X2 axis travel: 180 mm - Z2 axis travel: 650 mm - Y1 axis travel: ±40 mm - Z3 axis travel: 670 mm - X3 axis travel: 175 mm - Max. bar diameter: 100/104 mm - Number of driven tools per tool turret: 12 - Including chip conveyor, with 2 tool turrets (each with 12 tool stations), main and counter spindles, as well as foot switches Attention, the machine has the following defects: - The B-axis is defective (mounted on turret 1) - Guideways and drives show age-related wear - X2 axis (guide rails) runs slightly out of alignment by approximately 0.03 mm (should be re-measured) Lodoyaqgyjpfx Ahzehb - Occasionally, axis reference value setting in the control system fails - The hydraulic pump was replaced after a failure and is now installed externally as a standalone unit FCA D-58256 Ennepetal, loaded on truck at a mutually agreed date at the end of February 2026.

Condition: good (used), Year of construction: 2008, operating hours: 72,899 h, functionality: fully functional, machine/vehicle number: 07510001241, turning length: 1,185 mm, turning diameter: 640 mm, spindle speed (max.): 12,000 rpm, workpiece weight (max.): 150 kg, total height: 3,040 mm, total length: 7,800 mm, total width: 4,100 mm, overall weight: 16,500 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D, DMG GILDEMEISTER GMX 250 LINEAR CNC Turning and Milling Center - Recorded spindle hours: 39,361 - Swing diameter: 640 mm - Counter spindle turning diameter: 400 mm - Spindle distance: 1,500 mm - X1 axis travel: 550 mm - Y1 axis travel: 180 mm - Z1 axis travel: 1,185 mm Ljdoyaqczopfx Ahzshb - B1 axis travel: 240° - X2 axis travel: 180 mm - Z2 axis travel: 1,050 mm - Z3 axis travel: 1,150 mm - Spindle speed range: 3,200/4,000 rpm - Rapid traverse rate, Slide 1 (X/Y/Z): 40/24/70 m/min - Rapid traverse rate, Slide 2 (X/Z): 24/36 m/min - Rapid traverse rate, Slide 3 (Z): 36 m/min - Tool holder: HSK 63 - Spindle speed: 12,000 rpm - Number of tool stations in chain magazine: 40 stations - Incl. tool holders mounted on the turret - Incl. bar loader, manufacturer: COCCHE GIOVANNI, type: CNC-DB 110, year of manufacture: 2008, serial number: CNCDB-08.306, weight: 1,500 kg Note: The machine has the following defects: - The hydraulic unit is faulty – it needs to be repaired - The Q2 axis (milling spindle tool changer) fails frequently - X2 axis (guideways) moves slightly askew - The linear guides and drives show wear commensurate with age Attention: A vehicle with 3,000 mm transport width is required for transport! FCA D-58256 Ennepetal, loaded onto truck at a mutually agreed date at the end of February 2026.

Condition: used, Year of construction: 2001, turning diameter / mm turning length / mm Lhodpex Tu Sujfx Ahzjb control / total power requirement / kW weight of the machine ca. / t required space / m

Condition: used, grinding wheel diameter / mm no. of working stations / Stück Lhjdpfx Ahsx Ddayjzsb table surface area / mm

Condition: excellent (used), Year of construction: 2013, ERMIS automation for asphalt plant control Year 2013 Lodpjxz Tkvsfx Ahzohb

Condition: used, Year of construction: 1988, Distance between centres 1200 mm Speed A) 70 - 380 U/min. turning speeds B) 380 - 2000 U/min weight 2,2 t +++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Lsdpfxsk Sat Do Ahzehb Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. +++++

Condition: good (used), Year of construction: 2001, M01.43870 frequency 50 Hz voltage 400 V 24 V connected load 48 kW rated current 63 A control Siemens 840 D turning diameter 250 mm turning length 100 mm weight of the machine ca. 7,5 t turning length external / innen 100 mm workpiece length - min. 29 mm Lhsdpsrc Ip Sofx Ahzeb workpiece length - max. 100 mm

Condition: excellent (used), Year of construction: 2020, Swing over bed 880mm, Swing over saddle 817 mm, Maximum turning diameter 550mm, maximum turning length 3070mm, bar capacity 116.5mm, Y axis +/- 75mm, Spindle speed 2000rpm, milling speed 4,000rpm, Lodpfxsx I N Rbo Ahzohb spindle power 37/30KW, 12 station turret, Fanuc IPlus control. 3 jaw chuck, tool setter, Hydraulic steady, swarf conveyor,

Condition: used, Year of construction: 1999, 3 900 mm centre distance 2x 4mm mm Distance between centres 1x 5 mm mm Lodpfxex U A Tij Ahzjhb capacity 600 kp

Condition: used, Year of construction: 2005, revolutions per minute 8000 U/min x-travel 1000 mm Lhedoud Al Hepfx Ahzob y-travel 500 mm z-travel 570 mm Control Siemens weight of the machine ca. 5000 KG

Condition: good (used), Year of construction: 1977, workpiece weight 279 KG Lhodpforfd U Rjx Ahzsb length ca. von Bett bis Lynette mm 189 € . max durchlass 369 mm

Condition: good (used), Year of construction: 2003, functionality: fully functional, Technical details working diameter max. 32 mm spindle passage 36 mm turning length 320 mm Control MITSUBISHI MELDAS 635LC travel max. (X1) 108 mm travel max. (Y1) 275 mm travel max. (Z1) 325 mm travel max. (X3) 238 mm travel max. (Z3) 410 mm main spindle speeds: 200 - 8000 U/min c-axis 0,001° deg. Subspindle spindle speeds 200 - 7000 U/min c-axis 0,001° deg. rapid traverse 20 m/min main drive 3,7 / 5,5 kW Subspindle motor 1,5 / 2,2 kW dimensions of machine 2,77 x 1,24 x 1,79 m weight of the machine ca. 2850 kg Additional information CNC Swiss-Type Lathe First put into operation December 2005 The machine was used for a single shift and is in good condition with no maintenance backlog. Equipment: FMB Turbo 5-42/3200C bar loader, built 2004 High-pressure pump Lhsdpfx Ahsx Uzcvozeb Many collet chucks for main spindle Various collets Drive unit for synchronously driven guide bush Synchronously driven guide bush Drive unit for transversely driven spindle on linear support Pick-up spindle Collet chuck for pick-up spindle Blow-out device for pick-up spindle Five fixed tool holders on the rear Workpiece removal device Coolant tank Central lubrication system Door lock Ejection device for workpieces with through holes Machine documentation The machine will be sold without tools and extraction system.

Condition: good (used), Year of construction: 2006, functionality: fully functional, Technical details turning diameter 660/275 mm turning length 1498 mm control Fanuc/Mori Seiki MSX 701 total power requirement 90 kVA weight of the machine ca. 26,6 t dimensions of the machine ca. 5301 x 2997 x 2788 mm Additional information 9-axis CNC turning and milling centre * Fanuc MSX-701 CNC control * Milling spindle at top (B axis), as full 4th axis, positioning 0.0001 deg. * 40-position tool magazine * 10-position turret at bottom, all positions driven * 2 x 3-jaw quick-change chuck KNCS-N 315/91 * KNOLL high-pressure coolant system, pressure setting 12/25/35/45/55/62 and 72 bar, with maintenance-free rotary filter system * Chip conveyor * Drain system for main spindle chuck (controlled via M function) * Drain system for tool cutting edge (controlled via M function) * Coolant gun incl. accessories * Oil mist extraction * Direct measuring system X1, X2, Y-axis * Bar loader interface * Double foot switch for both spindles * Islands and pocket programming for MAPPS * High-speed fixed cycle for MAPPS * Programm memory extension to 8 MB * Programm restart * 3-stage signal lamp * 512 MB memory card (CF card) Swing diameter over cross slide (tool spindle 1): 750 mm Swing diameter over cross slide (turret 2): 400 mm Max. turning diameter (tool spindle 1): 660 mm Max. turning diameter (turret 2): 275 mm Max. machined workpiece length: 1498 mm Max. bar material: 90 mm Travels: X1 axis (tool spindle): 750 mm Y axis (tool spindle): 420 (+/- 210) mm Z1 axis (tool spindle): 1635 + 100 mm for tool change B axis (tool spindle): +/- 120 deg., full B-axis 1 deg. indexed and 0.0001 deg. braked X2 axis (turret): 195 mm Z2 axis (turret): 1525 mm SZ axis (subspindle): 1610 mm Rapid traverse: (X1,Z1) 50 m/min. / (Y,X2,Z2,SZ) 30 m/min. Main and subspindle: Spindle speeds infinitely variable (spindle 1 + 2): 30-3000 rpm. C axis (spindle 1 + 2): 0.001 deg. Main spindle motor: 22/18.5 kW Subspindle motor: 22/18.5 kW Torque (spindle 1 + 2): 1000 Nm Disc turret: Number of tool positions: 10 Speed of driven tools: 6000 rpm. Drive power: 5.5/3.7 kW Milling spindle head: Tool holder: HSK A63 Max. speed: 12,000 rpm Drive power: 18.5/11 kW Torque: 120/44 Nm Tool changer: 40-stations Tool diameter 70/140 mm Tool length 400 mm Tool weight 8/10 kg Total power requirement 90 kVA Main dimensions Length x width x height 5301 x 2997 x 2788 mm Ledpfx Ahox Uxdqozohb Machine weight 26.6 t Accessories: Measuring arm (picture) tool measurement in machine Tool holder + box, reduction sleeves, driven tools Clamping jaws package Collets package

Year of construction: 2015, condition: excellent (used), 10 turning steels Make Sandvik Coromant : 1 : 340 SC5 DCLHR 291311 285 2226 2 : 340 SC5 DCLHR 291311 285 2226 3 : 340 SC5 DCLHR 291311 285 2226 4 :C5-PCLNB-35060-12 Sumitomo 5: PSC50-DDHNL-35060-15 6: C5-PCLNB-35060-12 Sumitomo 7: C5-PCLNB-35060-12 Sumitomo Ledpfjfr T D Tsx Ahzjhb 8: SECO S5-DCLNR-35060-12 9: MPDES26073-105R03C 10 :MPDES 26073-105RO03C Tools are sold individually or as a lot Unit price 80 Euro plus VAT.

Condition: ready for operation (used), Year of construction: 1993, swing diameter 1400 mm faceplate diameter 1500 mm Ledpfx Ahsvxa Tpszohb Control Sinumerik 850T work height max. 1400 mm Tool changer 12 stck. workpiece weight 5 t YEAR OF CONSTRUCTION: 1993 Mechanical overhaul: 2010

Condition: excellent (used), Turning tools with rotating cutting plate Lodpjd Hflaofx Ahzohb Type: RRSDR 3232P12 Make Mitsubishi Length 165 mm