CNC turning and milling center

EMCO Hyperturn 665 MC Plus

Condition: ready for operation (used), Year of construction: 2008, operating hours: 12,125 h, spindle motor power: 29,000 W, spindle speed (max.): 5,000 rpm, controller manufacturer: SIEMENS, controller model: SINUMERIK 840D, number of axes: 6, This 6-axis EMCO Hyperturn 665MC Plus turn-mill centre was manufactured in 2008. It features a multi-axis CNC system with Y-axis and B-axis for complete machining of turned and milled parts. Equipped with integrated spindle motors on both main and counter spindles, it offers a spindle speed up to 5000 min-1 for the main and 7000 min-1 for the counter spindle. Includes a 24-position tool magazine and SINUMERIK 840D control. If you are looking to get high quality turning and milling capabilities consider the EMCO Hyperturn 665MC Plus machine we have for sale. Contact us for more information about this machine. Pgjdpey Hty Defx Adljk Additional equipment • Tool turret: 12-position tool VDI 30 radial with directional logic for up to 12 driven tool stations • B-PowerMill: Motorised milling spindle with 24-position tool magazine, 210° swivelling range • Optional tool package: Includes stationary and driven tool holders, collet chuck holders, reducing sleeves, and operating spanners • Hollow clamping cylinder with draw tube / Part ejector and flushing through the counter spindle / Part pick-up device for finished parts • Part pick-up device for finished parts / Coolant device in the chip conveyor / High-pressure pump (14 bar) and fine filter • Flushing pumps (3.7 bar) / Control cabinet air conditioning unit / Electrostatic oil mist separator • Hydraulic unit / Machine light / Interface for foot switch / Signal lamp • Documentation including handwheel, PC keyboard, network preparation, tool monitoring, turning window, cleaning gun • Clamping device for main spindle: Hainbuch BZI 80 centre pull / Machine Benefits Technical Machine Benefits • Counter spindle: 22 kw / counter spindle: 0-7000 rpm • Main spindle: kk 6 (passage 65 mm) / counter spindle: kk 6 • Y-axis travel range: +/- 50 mm • C-axis for main and counter spindle • Counter spindle: 3-jaw chuck 210 mm • Approx. 40 capto c4 holders for milling spindle • Loader lm 1200 • Machine does not have shopturn programming. It must be programmed using iso code, whereby simple cycles are available for drilling, milling, swiveling, etc. • 12-station turret and a milling spindle

Condition: ready for operation (used), Year of construction: 2010, General Data Measurements width 3056 mm Measurements depth 3994 mm Measurements height 2187 mm Machine weight 6360 kg Pedpfxex D Sc Ne Adlsgk Main Drive Spindle speed range 4000 Number of axis 5 Movement X-Axis Movement 260 mm X-Axis Rapid Traverse 30000 mm/min Y-Axis Movement ±50 mm Y-Axis Rapid Traverse 0000 mm/min Z-Axis Movement 795 mm Z-Axis Rapid Traverse 30000 mm/min B-Axis Movement 734 mm B-Axis Rapid Traverse 30000 mm/min Workpiece Workpiece drm over bed 590 mm Workpiece drm over support 360 mm This 5-axis MORI SEIKI NLX 2500 SY/700 was manufactured in 2010, featuring a max swing over bed of 590 mm and a cutting length of 795 mm. It includes Y and C axes, a sub-spindle, and high-pressure coolant system. Capable of handling bar work up to 80 mm, it's equipped with a chip conveyor and automatic bar feeder. Consider the opportunity to buy this MORI SEIKI NLX 2500 SY/700 turn-mill centre. Contact us for more information about this machine. Application Types Turning

Condition: excellent (used), Year of construction: 2007, turning length: 744 mm, turning diameter: 430 mm, spindle bore: 65 mm, Control: CNC path control with 10.4" TFT color display Siemens Sinumerik 840 D powerline TECHNICAL DATA Swing diameter * over bed: 600 mm * over cross slide: 500 mm Distance between main and sub spindle: 975 mm Max. turning diameter: 430 mm Max. turning length: 744 mm Max. bar diameter: 65 mm Max. workpiece size with sub spindle: ø 200 x 200 mm Main spindle Drive power: 29 kW Speed range: 0 – 5000 rpm Max. bar capacity: 65 mm Max. chuck size: 200 mm C-axis *resolution: 0.001° Sub spindle Drive power (100/40% ED): 17/22 kW Speed range: 0 – 7000 rpm Max. chuck size: 200 mm Travel (Z-axis): 750 mm C-axis *resolution: 0.001° Upper tool turret Disc turret with directional logic Number of stations: 12 of which driven: 12 Tool holder DIN 69880 VDI 30 Drive power: 6.7 kW Speed range: 0 – 4000 rpm Travel range * X-axis: 270 mm * Z-axis: 750 mm * Y-axis: +50 mm Lower tool turret Disc turret with directional logic Number of stations: 12 of which driven: 12 Tool holder DIN 69880 VDI 30 Drive power: 6.7 kW Speed range: 0 – 4000 rpm Travel range * X-axis: 205 mm * Z-axis: 750 mm EQUIPMENT/ACCESSORIES - Fully enclosed guard electrically interlocked, with sliding doors and machine light - IEMCA Master 890 MP bar loader (left side) for bar length 3300 mm, including: guide channel, centering unit, axial movement - Thermocompensation systems for integrated spindle motors (liquid cooled) - Hollow clamping cylinder with draw tube for main spindle - Solid clamping cylinder with draw bar for sub spindle - C-axes for main and sub spindle - Transmit software for easy C-axis programming - Y-axis on the upper turret (cutting force is distributed over 2 axes, resulting in extremely high rigidity) - Drive units in upper and lower turret - Parts ejector and flushing through the sub spindle - Finished parts pick-off device Maximum finished part: ø 65 x 200 mm Maximum finished part weight: 4.5 kg - Conveyor belt for removing finished parts from the machine - Turret steady rest including VDI 30 basic holder, controlled centrally via the coolant supply (14 bar), in the tool turret Clamping diameter range: 10 – 70 mm - Coolant system with 2 high-pressure pumps each at 14 bar and 2 rinsing pumps each at 3.7 bar - Cleaning gun for cleaning clamping devices, covers, and the entire working area with coolant - Swarf conveyor (hinge belt type) in extended version for gantry design, suitable for: long steel chips, chip nests, wool chips, dry and wet machining Pgjdpjyx U Hiofx Adlsk - Electronic oil mist separator 800 – 1000 m³/h - Automatic central oil lubrication for guideways and ball screws - Grease lubrication for main and sub spindle - Foot pedal for actuation of clamping devices - HAINBUCH collet chuck size 65 for main spindle, without stop (without collets) - HAINBUCH collet chuck size 65 for sub spindle, with stop type 100 (without collets) - 3-color signal lamp (red, green, white) - Serial interface - Mounting elements - Documentation

Condition: good (used), Year of construction: 2007, operating hours: 4,262 h, functionality: fully functional, machine/vehicle number: R7AV13, turning diameter: 65 mm, Can be powered up, the condition of the bar feeder is unknown, removed from production due to arrival of a new machine. On both turret heads, the use of a driven tool holder is possible in all positions. Pjdpfx Adjyxxhqjlogk

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A Podswp Rqfspfx Adljgk • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: like new (used), Year of construction: 2008, operating hours: 1,120 h, Controller ARISTECH (similar as FANUC) Number of axes: 4 Table size 640 x 470 mm X Axis Travel 425 mm Y Axis Travel 300 mm Z Axis Travel 250 mm Max workpiece size 800 x 600 x 250 mm U Axis Available:standard Weight cca 3000 kg Dimensions LxWxH = 1860 x 2050 x 2100 mm Psdpfx Aevvl Uaodlsgk The machine consist of following units 1. EDM machine 2. Controller cabinet 3. Water tank and pump 4. Water cooler 5. Transformer 6. Transformer Nr.2 (power supply) The machine was barelly used. Still unter power. It will be due to company liquidation.

Condition: like new (used), Year of construction: 2014, operating hours: 925 h, functionality: fully functional, turning length: 500 mm, turning diameter over cross slide: 290 mm, turning diameter: 500 mm, spindle speed (max.): 5,500 rpm, spindle bore: 73 mm, travel distance X-axis: 210 mm, travel distance Y-axis: 80 mm, travel distance Z-axis: 525 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 22 m/min, rapid traverse Z-axis: 30 m/min, total height: 1,808 mm, total length: 4,447 mm, chuck outer diameter: 210 mm, total width: 2,378 mm, swing diameter over cross slide: 290 mm, spindle nose: FL 140h5, overall weight: 4,300 kg, Equipment: documentation/manual, rotational speed infinitely variable, 925 spindle hours—in other words, virtually as good as new; that’s certainly the case for this DMG MORI CTX ALPHA 500 V4! The machine comes from a prototype department where primarily plastics were machined. Pedpfx Adey Duinolegk

Condition: good (used), Year of construction: 2012, Parts shown by hand not come. X1020mm Y610mm Z610mm Psdpfx Ajx Awzbodlogk 12.000 rpm,25 KW, 160Nm Control unit: HEIDENHAIN iTNC 530, 4th axis will come without parts shown by hand.

Condition: used, Year of construction: 2004, functionality: fully functional, machine/vehicle number: 8038938456C, turning length: 450 mm, turning diameter over cross slide: 505 mm, turning diameter: 202 mm, spindle motor power: 10,000 W, spindle speed (max.): 6,000 rpm, spindle bore: 51 mm, Gildemeister CTX 310 Heidenhain Turn+ The machine its full functional, but have some miner isue. Pgodpfx Adowk E Uzolek

Condition: good (used), functionality: fully functional, Year of construction: 1990, machine/vehicle number: 4ROLL, roller (bottom) diameter: 470 mm, roller (top) diameter: 470 mm, side roll diameter: 420 mm, roller diameter: 470 mm, roller length: 3,050 mm, working width: 3,050 mm, working height: 1,800 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 45 mm, sheet thickness aluminum (max.): 45 mm, sheet thickness copper (max.): 45 mm, overall weight: 43,000 kg, total length: 7,700 mm, total width: 2,410 mm, total height: 2,470 mm, power: 37 kW (50.31 HP), input voltage: 380 V, type of input current: three-phase, working length: 3,050 mm, Equipment: documentation/manual, emergency stop, PLATE BENDING MACHINE FACCIN - 4 ROLL HYDRAULIC 3000 X 40 MM MODEL 4HCI3-35/30 YEAR 1990 PLATE BENDING ROLL LINEAR GUIDEWAYS DOUBLE PINCH PRE-BENDING Psdpfx Adjwb Scmslsgk Machine in good working condition Bending capacity -Plate width : 3000 mm -Rolling plate thickness 40 mm - Prebend thickness 35 mm Rolls dimensions: -Useful length 3050 mm -central rolls upper/lower 470 mm -side rolls left/right 420 mm • Hardening of the 4 rolls high strength surface • 3 rolls driven powered with gear unit with hydraulic motor • Conical bending attachment side rolls tiltable to form cones, contrast pad roller type. • Opening front hydraulic drop-end to unload the closed shell. • Variable speed working roll bending rotation hydraulic speed fast/slow. • Console electric on wheels with centralized commands joysticks and 3 digital readout. • Digital readouts of the rolls position bending and pre-bending repeatability. • Hydraulic tank capacity oil 350 liters – power electric 37 Kw voltage 380 /50 • Dimension 7700 x2410 x H 2470 mm - weight 43000kgs