Conveyor belt with discharge

Reinhardt ATS

Condition: reconditioned (used), working length 3600 mm Working width 1140 mm Working height 820 bis 1050 mm WEINIG RF15 Return Conveyor System ----- Hsdpfx Aqjxpn Tnjpofn Suitable for use after a chamfering, planing, and milling machine with a maximum feed speed of approximately 22 m/min. For the continuous return transport of workpieces to the operator. After passing through the planer, the workpieces are transferred to a roller conveyor, where they are conveyed transversely and then taken over by a driven roller conveyor. This conveyor directs the workpieces onto a downstream longitudinal roller conveyor back to the operator and also serves as a parts buffer. Manufacturer’s technical specifications: Workpiece length: 250–3,600 mm Workpiece width: 30–230 mm Min. workpiece thickness: 10 mm Max. feed rate of the planer: 22 m/min Cross conveyor with 2 integrated roller conveyors: Cross conveyor length: 1,140 mm Constant conveyor speed: 30 m/min Max. cycles per minute: 40 Roller conveyor length: 2,200 mm Constant speed: 30 / 60 m/min Gear motor: 1 kW (1.3 PS) Operating voltage: 220/380 volts, 50 hertz Compressed air connection: 6 bar Longitudinal roller conveyor (non-driven): Length: 1,700 mm Width: 160 mm Swing-mounted, adjustable incline Special equipment: Extension of the longitudinal roller conveyor (non-driven) by 3,000 mm ----- Price of the above machine available upon request! ----- (Technical data according to the manufacturer—subject to change without notice!)

Condition: used, Diameter 70 log saw Hedpfx Aeft Huyoqpsfn

Condition: used, Weiss tensioning car with auxiliary car with rails fully hydraulic Hodpfx Ashwzrkeqpsfn track gauge: 90cm immediately available location: Austria, near St. Pölten

Condition: good (used), functionality: fully functional, roll diameter: 60 mm, roll width: 62 mm, total width: 160 mm, total height: 150 mm, total length: 3,000 mm, axle spacing: 33 mm, Heavy-duty double roller rails, 6 pieces Roller strips Hodporby Ilefx Aqpsfn Length per rail: 3 m The rails can be equipped with rollers as required.

Condition: like new (used), Year of construction: 2024, Cantilever rack double-sided used: Hot-dip galvanized screw system Scope of delivery: 4 double-sided shelf uprights, height 3,500 mm with foot parts each 1,200 mm 24 cantilevers with 1,200 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Also available in larger quantities: 20 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per upright side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height adjustable in 100 mm increments - 6 screwable cantilevers per upright and 2 foot parts with a depth of 1,200 mm, standard = 4 storage levels one above the other per stand side - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. Hjdjmkixwjpfx Aqpefn The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: used, Vesto saw with two discs for sale - electric motor: 2 x 7.5 kW, - complete with hydrostation, - electrical cabinet. Hedetqt T Ijpfx Aqpefn

Condition: refurbished (used), Year of construction: 2013, functionality: fully functional, power: 18.5 kW (25.15 HP), -300 mm x 2600 mm max. timber cross-section -circular saw blade D 900 mm determination of the value 8.000 € new flat motor 18.5 kW / 1450 r/min with flange 4.300 € new positioning gearmotor 1.700 € new circular saw blade AKE D 900 mm, Z 120, 10% discount 8.500 € new electrical control cabinet 22.500 € without steel construction and without assembly -the special saw was only used for about 5 hours after the overhaul >>Made in West Germany 100% Hjdpfxscbq Nwo Aqpefn massive steel construction with movable portal and mounted saw unit from above, circular saw motor 18.5 kW, 1450 rpm with electronic brake travel drive 2.5 kW with frequency converter, travel speed infinitely variable saw blade max. D 900 mm, cutting height max. approx. 300 mm if the saw unit is in the basic position, the circular saw blade is in a lower protective hood and completely covered. machine overhauled without additional safety devices >> The working width can also be increased by conversion

Condition: excellent (used), Overall dimensions length 4900 mm width 1600 mm height 1950 mm height of feeder top 860 mm Weight 1200 kg Dimensions of processed raw material diameter up to 400 mm length from 500 to 3000 mm Dimensions of the received prism from 55 mm Main motor power 2 x 5,5 kW Power supply 400 V(3 phase) Electric head extension Feeder feed Hfsdpfsugp Imex Aqpjn smoothly controlled by inverter speed 4-9 m/min Diameter of pulleys 600 mm Blade parameters length 4000 mm width 30 ÷ 42 mm thickness up to 1,1 mm

Condition: good (used), Longitudinal circular saw with max. 3 m cutting length max. cutting width 0.5 m Hfjdpfx Ajwumwfoqpon max. cutting height 100 mm motor 12 kW total length 5.8 m total width 1.55 m

Condition: used, Pneumatic tilting roller table 1500x2000x900mm Pneumatically tiltable roller table, stand. Size: 1500 x 200 x 900mm The height of the table in the open state: 1850 mm Hjdpfx Aouglrzsqpjfn