Slot boring machine

Robland LBM

Condition: new, Year of construction: 2022, New machine Year of manufacture: 2022 Standard Equipment: - Electrically powered height and tilt adjustment (0–46°) with automatic correction of cutting height during tilting - Eye-level, swiveling control panel - Double roller carriage, carriage length 3,000 mm - Manually adjustable rip fence with scale, including manual fine adjustment, max cutting width 1,000 mm - Crosscut fence with fixed 90° position, manually adjustable via scale up to 3,200 mm - Max saw blade projection: 150 mm - Max saw blade diameter: 450 mm - Drive power: 4 kW (5.5 HP) at 4,000 rpm - AKE main saw blade clamping system - Working height: 91 cm Motor 5.5 kW (7.5 HP) with VARIO F45: - Stepless speed control from 2,000–6,000 rpm - Precise speed adjustment to the material increases cutting quality and blade service life Extended Cutting Height for Single-Side Tilting: - This option enables single-side tilting with a large extraction hood for max blade Ø 550 mm and a blade projection of up to 204 mm - In combination with a scoring unit: max blade Ø 500 mm / max cutting height 179 mm - Only available in conjunction with at least 5.5 kW (7.5 HP) drive power 2-axis Scoring Unit for Tilting: - With motorized height and lateral adjustment, programmable scoring blade height with quick lowering and raising - Drive motor 0.75 kW (1 HP), 8,200 rpm - Retrofitting only possible on machines prepared for the scoring unit LED Lighting: - Highly energy-efficient LED technology for clear marking of the scoring area The Altendorf double roller carriage is renowned for its smooth operation and precision run. It can be locked steplessly in any position. The large double rollers, precision-manufactured from hardened steel, ensure the upper carriage remains absolutely accurate in conjunction with the lower carriage on the hard-chromed guide bars. This running quality is maintained even after decades of heavy use and exposure to dirt. The carriage construction features a highly rigid, torsion-resistant multi-chamber design. The table surface is finely planed and anodized. A hard-chromed round bar in the upper carriage serves as both the mount for the cross-slide and the interface for various accessories. The entire unit is low-maintenance and does not require lubrication. On/Off Switch on Double Roller Carriage: - The on/off switch on the double roller carriage is always within easy reach. With four buttons, both the main saw blade and the scorer can be switched on and off, saving time and increasing safety. Rjdpfx Aasw I Uxcjaer Angle/Mitre Fence, Crosscutting up to 3,500 mm: - This Altendorf-patented fence with integrated length compensation makes it easier to cut angles and mitres precisely in a single operation. In both positions, the swivel angle is steplessly adjustable by up to 49° and displayed on a scale. The play-free and robust stop flaps can easily be moved and adjusted as a single flap over the entire area up to max. 3,500 mm.

Condition: new, Year of construction: 2026, Combined saw-milling machine Rjdpfxjhp Rdle Aaaor minimax st 3c F 16 Swiveling saw blade, swiveling milling spindle and format sliding carriage made of anodized aluminum Sturdy cast steel construction Large support surface and precise cast table High-precision sliding carriage made of anodized aluminum (travel 2250 mm) Large trimming frame (900 x 600 mm) with telescopic aluminum fence extendable up to 2660 mm with professional stop flaps Max. Saw blade Ø 315 mm with scoring device, tiltable from 90° - 45 Saw parallel fence with fine adjustment Stable saw unit and large dimensioned double cradle milling unit guarantee highest stability, precision, smooth running and long service life Solid and precise machine table made of stress-free gray cast iron Three milling speeds, manually adjustable from 3500 - 10000 min-¹ With right-left rotation of the milling spindle Standard arc milling protection hood Safety turning stop jaws made of aluminum Two motors with high power reserves Two plug-in handwheels for convenient and quick operation Dimensions and weights Weight approx. 470 kg Connection suction Suction port diameter 2 x 120 mm Suction port diameter saw blade guard 60 mm Electrical data Power drive motor 2 x 5,0 kW Supply voltage 400 V Mains frequency 50 Hz Milling spindle spindle inclination 0 - -45 ° useful length of spindle 100 mm spindle speeds 3500/7000/10000 min-¹ Milling tool diameter max. not lowerable 210 mm lowerable 180 mm tenon milling 275 mm K

Year of construction: 2020, condition: ready for operation (used), A Rico compressor system consisting of two Atlas Copco compressors, two refrigerant dryers and an Atlas Copco Beko oil-water separation system is available. Screw compressor Atlas Copco GA 45 VSD+, year of manufacture: 2020, air volume flow: 9.4m³/min, operating pressure: 13bar, motor power: 45kW, motor speed: 4500rpm, machine dimensions X/Y/Z: approx. 1200mm/1100mm/2000mm, weight: approx. 860kg. Screw compressor Atlas Copco GA 45 VSD FF, year of manufacture: 2012, power: 45kW, operating pressure: 18.5bar, speed: 3000rpm. 2x refrigerant air dryers Atlas Copco FX 15, air volume flow: 15m³/min, operating overpressure: 13bar, pressure drop: approx. 0.3bar, refrigerant: R410A, refrigerant charge: 2050g, max. inlet air temperature: 60°C, machine dimensions X/Y/Z: approx. 900mm/750mm/1000mm, weight: approx. 160kg. Compressor management system Atlas Copco Equalizer 4.0/ES6-MK5, control range: 2-6 compressors. Oil-water separation system Beko ÖWAMAT 15, throughput range: 6m³-30m³/min, oil outlet: DN40, container volume: 115.5l, filling volume: 84.3l, oil collection container: 2x10l, max. operating pressure: 16bar, machine dimensions X/Y/Z: approx. 1100mm/550mm/800mm, weight: approx. 40kg. System operating hours: 8656h, controller hours: 42334h. Documentation available. An on-site inspection is possible. Rodpexdc Uvsfx Aaasr

Condition: used, Year of construction: 2018, Used machine Year of manufacture: 2018 Special feature: Machine for up to 100 mm edge height! Condition: Factory-inspected by Lange Maschinenbau Equipment and technical data: - Machine table with 13 running rollers for improved workpiece guidance Rodpowka S Iofx Aaajr - Edge feeding, synchronous with belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with knife (for cuttable edges) - Three pressure rollers - Belt feed: - 0.25 kW - approx. 1250 mm long - approx. 6.0 m/min - 50 mm wide toothed belt with thick, workpiece-friendly rubber top - Digital counter for height adjustment - Direct glue application to the workpiece: drip-proof glue pot with glue supply from below and rapid heat-up time after standstill - Flush cutting unit: - for front and rear workpiece edges - automatic sensing at the workpiece - pneumatic cutting with knife for cuttable edges - Flush trimming unit - with vertical sensing and horizontal guidance - reproducible setting using digital counters - 2 powerful 0.4 kW high-frequency motors - stepless speed adjustment from 4000 to 18000 rpm - Cutter Ø 70 mm, Z4, radius 2 mm/15° - central extraction nozzle Ø 100 mm - 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with belt feed - Continuous workpiece support approx. 1800 mm long - Workpiece support rail, extendable by approx. 300 mm - Rotatable foil dispenser Ø: 800 mm - Workpiece width: min. approx. 80 mm - Workpiece thickness: 10 – 100 mm - Workpiece length: min. approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation: max. 1.0 x 55 mm, 2 x 45 mm - Glue pot heating capacity: 2.7 kW - Heat-up time: approx. 10 minutes - Working height: approx. 880 mm - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Pneumatic connection: 6 Bar Dimensions (without foil dispenser): approx. 1800 x 700 x 1300 mm Weight: approx. 260 kg Availability: short-term Location: Flörsheim

Condition: new, Year of construction: 2026, CORMAK PBM290 horizontal drilling machine is a professional device created for efficient wood machining. It is equipped with advanced solutions ensuring perfect quality of finished products. Machine features high-quality guides, providing easy table height adjustment easy one-handed usage due to a well-placed handle simple and smooth table movement left/right spindle rotation 100 mm diameter extracting connector Rjdevuq Dkjpfx Aaaor Table dimensions 500 x 200 mm Drilling table height 760–900 mm Maximum drilling width 300 mm Maximum drilling depth 140 mm Spindle speed 2850 rpm Drilling chuck 0–16 mm S1 continuous work motor power 2.2 kW Power supply 400V Dimensions 770 x 920 x 1245 mm Weight 102 kg

Condition: new, Year of construction: 2025, Roller diameter: 640 mm Rjdpfogtdpmjx Aaajr Stand projection: 620 mm cutting depth: 400mm table tiltable: yes -0 to + 15° Table size: 870 x 620 mm belt speed: 1660m/min Motor power: 2,2 kW / 400V Motor brake: yes / automatic Suction connection: 2 x 120mm Machine length: 1190 mm Machine width: 780 mm Machine height: 2063 mm Weight: 320 kg

Condition: excellent (used), Maggi Boring System 35 Multi-spindle Drill Number of spindles 35 Spacing between spindles 32mm Distance between first and last spindle 1088mm Maximum drilling depth 85mm Rsdjvx Aqdjpfx Aaasr Spindle speed 2800r.p.m Number of pneumatic clamps 4 Machine working pressure 6-8bar Air demand per cycle 15l Number of motors 2×1.5kw Weight 450kg CE certificate

Condition: used, Year of construction: 1993, Used machine Year of manufacture: 1993 Equipment and technical data: - Fixed milling spindle; newly fitted bearings - with table extension and extendable frame support 2500 mm - Motor 5.5 kW - Speeds 3000/4500/6000/8000/10000 rpm - Milling fence with 2 adjustment options: - complete fence - rear take-off jaws - Extraction hoods: 2 x 120 mm - Automatic motor brake - Right/left rotation - with Haffner power feed with 4 rollers Weight approx. 700 kg Availability: by arrangement Rsdpfx Aaew I Uineaer Location: Flörsheim

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, TERSA cutterhead with 4 knives, 5.5 kW motor, 400 V, 50 Hz, electronic start and brake unit. Thickness table adjustment with buttons for rapid or slow feed, as well as fine adjustment accurate to 1/10 mm. Integrated operating hours counter. Thickness table mounted on 4 support spindles and 4-way guided. Two feed speeds: 7 and 14 m/min. One rubber feed-in and one rubber feed-out roller. Two extraction ports Ø 160 mm. Slide for top extraction. Planer guard system SUVAMATIC. Motor power 7.5 kW. Positioning control including sensor monitoring. Rsdpox Ey Tzefx Aaaer

Condition: new, Year of construction: 2026, A550 Fully Automatic Solid Wood Saw 9 m Fully automatic cutting of medium-large wood with simple-to-use automation. Put down any wood and the machine will automatically detect it and cut it into jobs tasked with high-accuracy servo motor material positioning. Excel job lists WIFI input for streamlined input of large cutting lists. Your fully automatic saw can optionally come as an inline optimiser saw. For every piece of wood you place down to cut, no matter what length, a laser sensor will measure its length. Our powerful optimisation algorhithm then takes your cut list and calculates the best order of parts to cut from this wood so that wastage is minimised. All of this happens on-the-fly, during the machine operation process, and without needing any input from you. • Fully-automatic cutting operation with bar feeding and cutting to length. • Simple user interface for automatic operation, enter job and cut in seconds. • Simplified part, batch, or large excel lists job cutting. • Bundled / multi-bar cutting and counting. • Remote WIFI excel job lists input with extensive data mapping capabilities. • Fully adjustable saw cutting and wood feeding rates for maximum process productivity. • Automatic labels printing for parts using data from the job list (manual label application, optional). • Inline direct-to-material printing with no operator action required (optional). • Bar codes or QR codes printing or scanning for jobs input (optional). • Automated servo positioning of the saw mitre angle up to ±75° (optional). Highly suitable for: • Frame and truss manufacture • Sheds manufacture • Furniture manufacture • Mitre timber structures manufacture • Bulk wood cutting Model: A550 Length: 9 m Rsdef Ekngjpfx Aaaer Material Length: 8580 mm Pushing capacity: 20 - 40 kg Software: Optimiser QUALITY AUSTRALIAN-MADE MACHINES.