2018 Tetra Laval Cook / Cool system

Tetra Laval Food Processor 2500.

Condition: used, Year of construction: 2022, Maximum parent roll width: 1420 mm Minimum parent roll width: 600 mm Maximum parent roll diameter: 1500 mm Maximum parent roll weight: 2500 kg Maximum unwinding tension (Ø1500 mm): 600 N Minimum unwinding tension (Ø1000 mm): 40 N Minimum standard slitting width: 100 mm Maximum rewinding width: 1400 mm Maximum rewinding diameter: 1050 mm Maximum rewinding weight: • Ø76 mm shaft: 600 kg • Ø152 mm shaft: 1000 kg Maximum rewinding tension: 600 N Maximum production speed: 600 m/min Power supply: 3 x 400V 50Hz Installed power: 30 kW Compressed air: 6 bar, dry Materials to be slit: • Paper-based / liner-based packaging laminates. • Board from 80 to 300 g/m². Unwind section: A separate between-centers unwinder, type T9, 1500 mm diameter, including: Gkodoyx Uy Aspfx Al Soc • Hydraulic cylinder control for lifting parent rolls from the floor. • Two motors driving the unwinding roll, controlled by an ultrasonic diameter sensor and a tension-control dancer roller. • Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3”) cores. • Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6”) cores (mounted on the pneumatic end adapters). • Floating edge-correction roller. • Automatic web guiding system, FIFE DP20, with SE26A photoelectric sensor, ±100 mm correction via electric actuator — for controlling sheet edge or continuous printed line. • Connecting walkway allowing web threading at floor level while keeping full access to the slitting station. • All web path rollers are anodized. • Safety guarding for operator protection. Slitting section: A slitting station with individual pneumatic knives and circular counter-knives: • Shear cut performed against the counter-knives. • Counter-knife shaft driven by an independent motor; counter-knife shaft is pneumatic. • Pneumatic knife holders mounted on a beam with a dovetail guide (TIDLAND) and an air supply manifold for individual activation. • 10 slitting sets, each including: Individual TIDLAND pneumatic knife holder (25 mm width) and double-bevel circular knife Ø 90/60 mm. • Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm length. Web separation section: • A separator roller driven by the slitting motor; angle and curvature fully adjustable. Lay-on roller: • Lay-on roller made of anodized ground aluminum or polyurethane (depending on materials). • Pressure is adjustable and synchronized with winding diameter. • Roller is removable. Automatic splicing / transverse cutting system: • Hydraulically operated pivoting arm including a transverse knife with linear motion and a backing plate for securing the web onto new cores. Trim extraction system: • Trim suction unit with two width-adjustable nozzles. • Turbine enclosed in a sound-insulated cabinet, conveying trim to a centralized system or container (not included). Rewinding section: • Motorized turret (two-position) supporting two rewinding shafts. • Rewinding shaft drive by an oversized asynchronous motor. • Hydraulic centering point for the active rewinding roll. • Two pneumatic expanding shafts Ø76 mm (3”), max load 600 kg each, equipped with full-width rubber strips with individual bladders. • Two pneumatic expanding shafts Ø152 mm (6”), max load 1000 kg each, also equipped with full-width rubber strips with individual bladders.

Year of construction: 2002, condition: not inspected (used), Robot no control panel + connection cables Used, untested robot. No technical documentation available. Not tested. Gkjdpegu U Itsfx Al Sec

Condition: good (used), Rotary vane booster pump Manufacturer: Leybold Type: RUVAC RA 9001 Condition: Overhauled and available as tested and serviced Gksdpfxod Hh Nve Al Sjc Includes: New paint job, motor relubrication, electrical inspection Warranty: up to 12 months Delivery time: in stock

Year of construction: 1996, condition: excellent (used), Thermoformer Brand Multivac Model R 530 Machine number: 837 Year of construction: 1996 Gksdpfx Alewa D A Ae Soc Power 15 kW Voltage 415 V, 3 Ph, 50 Hz, 35 A Film width: 620 mm Form: (3x) 180 mm x 160 mm Labeler Brand MR Etikettiertechnik GmbH Model MR293 Machine number: 23646/05 Year of construction: 2004 Overall dimensions: 8800 mm x 1400 mm x 1960 mm Including suction device for resting film Dimensions: 600 mm x 500 mm x 1060 mm Without main vacuum pump, vacuum was regulated centrally, labeler is incomplete.

Condition: used, Plant from spiral freezer. Gksdpfx Ajvvm Afjl Soc

Condition: ready for operation (used), Year of construction: 2010, operating hours: 15,043 h, laser power: 3,600 W, travel distance X-axis: 6,500 mm, number of axes: 5, This TRUMPF TruLaser Tube 7000 KT02 was manufactured in 2010. It features a working area of 6500 mm on the X-axis and can handle circular diameters up to 200 mm. Equipped with a CO₂ laser TruFlow 2000 and a laser cutting head with a 155 mm lens, it's ideal for precise tube cutting. Contact us for more information about this machine. • Circular diameter: 200 mm • Reject station: 3 m with brush table • Reject tray • Working Range X Tube Axis: 6500 mm • Outer Circle Diameter: 254 mm (Upgraded from standard 200 mm) • Unloading Station: 3 m with brush table, front unloading • Laser Type: CO2 Laser TruFlow 3600 including LensLine (Surcharge upgrade from standard TruFlow 2000) • Control: Sinumerik 840D, Teleservice • Standard Software/Features: NitroLine, FocusLine, SprintLine, Laser power control, Programmable cutting gas pressure, Program re-entry, Automatic shutdown, Workspace lighting, Laser logbook function, Laser cooling unit • Laser: CO₂ laser TruFlow 2000 • Laser cooling unit • Cutting Head: Lens cutting head with 155 mm focal length, ControlLine • Control unit: 84D • Connectivity/data transfer: RJ-45 network connection, USB connection; network connection incl. installation • Safety: CE marking, Multi-beam light barriers, Compact dust extractor 1500 Nm³/h, Protective cabin with Makrolon panels • Ambient Operating Temperature: Up to 43°C • Installation Type: Special machine installation setup Additional equipment Gjdpfxex D I H Ds Al Sekc • Accessories: • Spare parts case for cutting heads • 1 x remote control kit • Clamping jaw set Ø 16 / 200 mm • U-shaped guide rails for reject station with ID = 200 mm • Automation: • Loading Unit: LoadMaster Tube 6.5 m with bundle support, 2 grippers, 254 mm outer circle diameter capacity, low-scratch design for 6m, swiveling conveyor line, additional gripper D=254 mm • Options for LoadMaster Tube 6 m: • Circular diameter 250 mm • Shorter belt support • Swivelable conveyor section • Additional gripper Ø 200 mm • Additional gripper Ø 250 mm • Special equipment: • Flexible reject station 4.5 m (prototype) instead of reject station 3 m, without brush table • Special installation for flexible reject station • LoadMaster (series version 103) • Installation 100 mm higher (use of wire mesh container possible), decision upon acceptance • Services: • Installation, commissioning, training

Condition: excellent (used), functionality: fully functional, Alfa Laval / Tetra Pak Cream Pasteurization Line Alfa Laval / Tetra Pak Cream Pasteurization Line | Piston Pump, Buffer Tank, Flowmeter, Pasteurizer Complete cream pasteurization line from renowned manufacturers Alfa Laval and Tetra Pak, equipped with high-quality pumps, valves, flowmeters, and control cabinets. The line is designed for hygienic and efficient cream pasteurization in the dairy industry. Capacity: 35,000 liters/hour Main components of the line: 1. Circumferential Piston Pump Manufacturer: Alfa Laval Type: DURACIRC 73 Serial Number: E256143 Year of Manufacture: 2021 Dimensions: 1600 × 600 × 800 mm Included: various valves and stainless steel filter housing 2. Stainless Steel Buffer Tank Tank dimensions: Ø 1100 × 1700 mm Total dimensions: Ø 1200 × 2900 mm 3. Alfa Laval Valves, Type: Unique SSV (6 pcs.) High-quality single seat valves for food applications 4. Flowmeter Manufacturer: Endress + Hauser Model: Promag P / Promag P Dimensions: 200 × 200 × 350 mm High-precision flow measurement for food-grade liquids 5. Centrifugal Pump Manufacturer: LKM Type: LKH 20/155 Power: 5.5 kW Production Number: 20-02319 Dimensions: 700 × 380 × 400 mm Stainless steel construction, suitable for CIP operation 6. Valve Manufacturer: Armaturen AG Type: MA9.31A6 5S Po Dimensions: 600 × 400 × 400 mm 7. Cream Pasteurizer Manufacturer: Alfa Laval / Tetra Pak Type: C10-SH Serial Number: 30104-38526 Year of Manufacture: 2003 Capacity: 1311 liters Operating parameters: Godpfextu Ugox Al Sokc Operating pressure (PS): 0 / 20.0 bar Test pressure (PT): 28.6 bar Temperature range (TS): 0 / 130 °C Dimensions: 5000 × 800 × 2200 mm High-efficiency heat exchanger system ensuring stable pasteurization 8. Centrifugal Pump Manufacturer: Pomac Type: CP29068/230 X 15 Serial Number: 22 818 Year of Manufacture: 12/2011 Capacity: 45 m³/h Power: 15.0 kW Dimensions: 950 × 400 × 500 mm 9. Nocado Valves (5 pcs.) Process valves for food applications 10. Control Cabinets Manufacturer: Eldon and IPBE Dimensions: 400 × 230 × 770 mm 1000 × 300 × 1000 mm The Alfa Laval / Tetra Pak Cream Pasteurization Line is a complete industrial solution with a capacity of up to 35,000 l/h, designed for high hygiene, precise process parameter control, and maximum reliability. Ideal for dairies, cream and milk fat producers.

Condition: refurbished (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: D91402707010001/2013, overall weight: 1,500 kg, Electric motor for sale For description, see nameplate and pictures Sale only within EU member states! Not a private sale The MAE is available for inspection. We accept no liability for any warranty claims. We assume no liability for the accuracy of the technical data and year of construction, for the completeness of accessories and tools, as well as for compliance with all safety and environmental requirements mentioned in the accident prevention regulations. We assume no liability for the accuracy of the technical data and year of construction, for the completeness of accessories and tools, Gsdpfswittpjx Al Sskc as well as for compliance with all safety and environmental requirements mentioned in the accident prevention regulations.

Condition: good (used), Year of construction: 2005, functionality: fully functional, cooling capacity: 350 kW (475.87 HP), type of input current: three-phase, overall weight: 1,930 kg, input voltage: 400 V, total width: 1,200 mm, total length: 3,600 mm, total height: 2,000 mm, AMMONIA CHILLER GEA GRASSO 350 KW Brand: GEA Cooling capacity: 350 kW Refrigerant circuit: 1 pcs. Type of refrigerant: R717 Year of manufacture: 2005 Compressors: 1 pcs. reciprocating GRASSO Heat exchanger: Shell and tube Dimensions: 3.60 x 1.20 x 2.00 m Weight: 1930 kg Condition: Used, tested, fully operational CONDITION, TESTING & READINESS The chiller / kaltwassersatz / undergoes seven stages of technical inspection and operational parameter verification. It is also tested at our own test station, with connection to water (or glycol) and adjustment of parameters according to your requirements. After testing, you will receive a detailed report with the operating performance and the overall condition of the chiller. The chiller / kaltwassersatz / is ready for transport and commissioning. Our engineers will assist you with cooling capacity calculations, selection of the appropriate cooling scheme, and configuration of the required equipment options. WARRANTY & SUPPORT The quality of the equipment is confirmed with a warranty ranging from 6 to 36 months. Our company can also offer: - refrigerant charging; Godpfx Aleim R A Is Sskc - replacement of oil and filters; - technical support. LOGISTICS - Worldwide delivery available - Support with loading, export documentation, and logistics coordination Get a detailed consultation. Photos, videos, and a full testing report can be provided immediately upon request.

Condition: not inspected (used), Various chillers and condensers/liquefiers from bottling plant, dismantled, for sale, among others: 10 cooling plants, make Hafner + Muschler, complete on frames, each with 2 compressors, incl. electrical- and control cabinet, refrigerant R134a, power consumption: 150 kW / 198 kW / 238 kW, years of construction 2002 - 2008, dimensions each approx. 3,100mm x 1,600mm 3 condensers/liquefiers, make Thermofin, each with 4 fans, years of construction 2006/2008/2016, dimensions each: 4,200mm x 2,300mm 4 condensers/liquefiers, make Güntner, each with 8 fans with 890 rpm, 246.7 lt volume, 32 bar, year 2002/2016, dimensions: 6,150mm x 2,300mm Gksdpfx Alsh Nq E Sj Sjc 2 condensers/liquefiers, make Güntner, each with 6 fans, 93 lt. content, 28 bar, year 2002, dimensions: 6,050mm x 2,400mm