Chipper with horizontal feed

Vecoplan 350

Condition: excellent (used), Vecoplan 350/140 Chipper / Shredder Catalogue No. 7742 TECHNICAL DATA - Infeed width: 350 mm - Infeed height: 140 mm - Shaft width: 345 mm - Shaft diameter: 290 mm - Number of knives: 2 pcs - Screen size: 55x55 mm - Toothed feed shaft from above and below - Shaft motors: 2×1.5 kW - Electric auto-reverse (adjustable) - With vibrating chute - Vibrating chute length/width: 3750×355 mm - Full vibrating chute dimensions: 3750x620x1210 mm - Discharge with conveyor belt: 2970x340 mm - Conveyor belt dimensions: 3000x630x750 mm - Main motor: 22 kW - Dimensions (L/W/H): 3000x1100x1500 mm - Weight: approx. 2500 kg ADVANTAGES – German-made – with vibrating chute – With discharge conveyor – Auto-reverse – Used chipper, in very good condition Nsdpfx Asyi Tmzsnfewf Net price: 47,900 PLN Net price: 11,400 EUR depending on the exchange rate 4.2 EUR (Prices may change with significant fluctuations)

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: Nwsdpfx Anewp Rqfofsf • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: new, Year of construction: 2026, Drum chipper series ATH S&F chippers and drum chippers with horizontal infeed are used in many areas of the wood processing industry (sawmills, timber mills). Chippers from the ‘ATH’ series produce high-quality and homogeneous wood chips with a low proportion of fines from residual wood, for example as quality chips for the cellulose industry or as fuel chips for energy generation ATH 220 series - Feed height: 200 mm - Feed width: 500 | 700 | 1000 mm - Number of chipper knives: 2 - 4 pieces - Number of counter knives: 2 pieces - Rotor diameter:520 mm - Number of feed rollers: 3 pieces - Throughput: up to approx. 40 rm/h * - Chipping length: 5 - 50 mm - Chipper drive power: 22 - 110 kW - Drive power feed rollers: 2 x 2.2 kW - Operating/control voltage: 400/220 V, 50 Hz - Weight: 2,800 - 4,000 kg Nwodpfjuz Hmxjx Anfef ATH 330 series - Feed height: 300 mm - Feed width: 500 | 700 | 1000 mm - Number of chipper knives: 2 - 6 pieces - Number of counter knives: 2 pieces - Rotor diameter: 700 mm - Number of feed rollers: 3 pieces - Throughput capacity: up to approx. 70 rm/h * - Chipping length: 5 - 80 mm - Chipper drive power: 37 - 250 kW - Drive power feed rollers: 2 x 3.0 kW - Operating/control voltage: 400/220 V, 50 Hz - Weight: 3,500 - 5,000 kg *depending on chipper length, kW main motor, number of knives, feed Advantages: - Maximum throughput - Low fines content - Low maintenance - Flexible use - Customised production

Condition: new, Year of construction: 2023, Application combs 10 mm Application combs 15 mm Application combs 20 mm finger joint profile 15 mm finger joint profile 20 mm delivery time 3 days Nwsdpfx Ajiacbpenfsf

Condition: used, Total height 6500 mm Floor space 2000 x 2000 mm Outdoor installation Compact filter series Model PKFP – 1 element – 1.92 x 1.92 Shaking filter Overpressure operation Filter hose length 2500 m long – 180 mm diameter - then 105 m2 filter area 2 raw air fans – 2 pipes (diameter 300 mm) 1 x fan KT 300, 15 kW power 6361 m³/h built in 1999 1 x fan S 25 / 300, 7.5 kW power 7400 m³/h, built in 1993 1 x transport fan 6.1 kW, power 57 m³/min, built in 1996 Total approx. 14,000 m3/h volume flow Briquette press Höcker Polytechnik type BrikStar C 3 - 12. 1225 Motor 3.0 kW, briquette diameter 65 mm, output approx. 40-45 kg/h depending on the specific weight of the material. Nodpjvviytefx Anfswf Storage location: Nattheim

Condition: refurbished (used), Completely refurbished Bongioanni CRL 4 tensioning wagon with clamping blocks. Track gauge 1200 mm. Rails newly milled. Servo-electric drive. Sale upon customer order. Nsdjxtwxbjpfx Anfswf

Condition: used, Year of construction: 2003, operating hours: 10,120 h, total length: 1,800 mm, total height: 1,700 mm, total width: 1,200 mm, Empty weight: 1.300 kg Price: On request Shredder Untha LR 630 Year of construction 2003 Input opening: 624 x 792 mm Throughput speed: material and sieve dependent Rotor diameter: 248 mm Rotor speed: 86 - 96 rpm Nwodpfxowh Na Ns Anfjf Engine power: 15 kW Cutting system: 17 knives Sieve diameter 24mm Transport dimensions 1800*1200*1700mm (L*W*H), Weight 1300kg - Year: 2003 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: LR632318 - Operating hours: 10120 - Transport dimensions: 1800mm x 1200mm x 1700mm (l x w x h) - Transport weight [kg]: 1300kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: new, Year of construction: 2024, The fully automatic robotic palletizing system is developed and manufactured by our company. Robotic palletizing systems are able to meet the needs of a very diverse range of sectors. * Flour factories, * feed factories, * fertilizer factories, * cement factories, * construction chemicals factories, * legume factories, * Packaged products, * Bagged products, * Transportable products, Features and benefits : - Faster palletizing, - Standard number of pallets, - Saves work, energy and time, - Correct placement thanks to automatic tolls, - High robustness on the pallet with appropriate loading sequence, - Can be arranged in various configurations; rows of pallets with free programming, - 400-5000 packages/hour performance, - From 5 to 50kg standard packages, - Space requirement for installation is small and flexible, Njdpfouua Hqox Anfswf - User friendly - low maintenance, Basic elements high palletizer : * Gripper for Robot, * Conveyor belt, * roller conveyor, * Bag smoother, * Rotation unit, * loading platform, * stretch wrapper, * pallet feed unit, * Empty pallet unit, * Electrical & Automation & PLC, * Fence and operator protection equipment,

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 Nsdpfx Aju Hmacenfewf 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power Nwodpsq Nf Enofx Anfsf 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.