Condition: ready for operation (used), Shelf length 2500 mm Lsdpfx Asyynzpolneaa Shelf width 1200 mm 4 hydraulic pistons 75 mm Clearance 400 mm Water heating

Condition: ready for operation (used), Shelf length 2500 mm Shelf width 1300 mm 4 hydraulic cylinders 85 mm Ljdpfx Aeyynm Eelnoaa Clearance 450 mm Water heating

Condition: used, Year of construction: 2014, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, pressing force: 962 t, stroke length: 200 mm, table width: 1,400 mm, table length: 2,750 mm, working width: 1,400 mm, operating temperature: 135 °C, operating pressure: 290 bar, workpiece height (max.): 200 mm, workpiece weight (max.): 250 kg, cylinder diameter: 270 mm, opening width: 200 mm, plate width: 1,400 mm, pressure: 25 bar, temperature: 150 °C, We are offering this used ITALPRESSE MARK C/ 14-27.5/2 veneer press, year of manufacture 2014. Machine type: MARK/C 14-27.5/2 Serial number: 184450514 Rated voltage: 400 V Frequency: 50 Hz Year of manufacture: 2014 Single-level through-feed press system with top ram Machine is in perfect working condition Meets CE safety standards The machine can also be purchased together with other machines as part of a complete production line. Heating plate dimensions: 1400 x 2750 mm Number of heating plates: 2 units Number of levels: 1 unit Cylinder stroke: 200 mm Daylight opening: 200 mm Feed side: 1400 mm Specific pressure at 100%: 25 Kg/cm² Total pressing force: 9620 kN Cycle time: 2-30 min Operating temperature: 135°C Max. surface operating temperature: 150°C Intended heating medium: thermal oil Number of press cylinders: 6 units Lodpfxeyxp Twj Alnjaa Diameter of press cylinders: 270 mm Return cylinders: 4 units Operating pressure: 290 bar Closing speed: 50 mm/sec Opening speed: 50 mm/sec Operating voltage: 400 V Mould data: External mould dimensions: 1340 x 2540 mm Max. mould weight: 250 kg Mould cover dimensions: 1200 x 2400 mm Moulds are not included in this offer but can be supplied at additional cost Powered infeed roller conveyors: Dimensions: 1400 x 3500 mm Feed speed: 8-40 m/min Light barrier control Electropneumatic shaking device for the upper Mylar film Electronic flatness control Automatic switching to pressing speed Compressed air equipment in the lower press table Cylinder support plates are insulated and drilled from solid material for water cooling Feed speed with frequency control Powered outfeed roller conveyors, dimensions: 1400 x 3500 mm Electrical control cabinet / Siemens S7 PLC control panel Dismantling and collection at buyer’s own expense Pick-up location: A-8265 Kroisbach an der Feistritz If you have any questions or require further information, please send us a message or give us a call.

Condition: good (used), Year of construction: 2001, Good, used condition Low operating hours (1,675 h) Motor: 11 kW Pressure: adjustable up to a maximum of 250 bar Throughput: up to max. 220 kg/h Briquette size: 150x60 mm Press dimensions: approx. 2200x3000x1920 mm (LxWxH) Control cabinet dimensions: 500x1250x2120 mm (LxWxH) Laodpowcc D Rjfx Alnja Weight approx. 3,000 kg

Condition: used, Year of construction: 1995, Technical details: punching pressure: 25 (250kN) t pass through width: 1800 (1660 nutzbar) mm Ledpju Szfujfx Alnsaa daylight between the columns: max./min.: 155 / 25 mm stroke: Stanzhub: 130 mm total power requirement: 5,0 kW weight of the machine ca.: 2,0 t Dimensions (LxWxH): 2,3 x 1,0 x 2,2 m Hydraulic trolley beam punch hydrl. pressure 250 bar Punching table area = 1830 x 500 mm Punching trolley/plate = 500 x 500 mm; travel speed = 800 mm/sec.; punching stroke = 63 mm/s, forward/return 125/125 mm/sec. Operation via control panel and pressure switch/control lever Equipment: 2x feed rollersØ 120 x 1630mm pneumatic close/open *

Condition: excellent (used), Year of construction: 2021, operating hours: 9,500 h, functionality: fully functional, machine/vehicle number: 3284, Standard version of RUF Lignum R2 with outfeed channels, el.motor 22 kW, briquette sizes 150x60 mm capacity up 500 kg/h Ljdeyyl Srjpfx Alneaa

Condition: good (used), Year of construction: 1990, 1x HOT PRESS for VENEER “SORMEC” TYPE 350X130 Hydraulic hot press for wood, panels, furniture, doors, composites, and various materials Ledpfx Aloyv Izbonjaa Technical data: Platen dimensions: 3500 x 1300 mm 1 USEFUL WORKING PLATE Platen heating by hot water Total pressure: 50 tons Opening: 300 mm 8 cylinders, diameter 85 mm Water boiler not included Overall dimensions: 4500 x 1600 x 2500 mm (H) Weight: approx. 5000 kg Second-hand, in good condition

Condition: excellent (used), Year of construction: 2017, operating hours: 12,000 h, functionality: fully functional, For sale: 4 UMP BP 500 A sawdust briquetting presses Years of manufacture: 2017, 2022, 2022, 2023 The machines are fully operational, all after complete servicing. Laedpfx Aloyr S T Sjnea

Condition: used, Year of construction: 2000, Main features Exceptional durability allowing operation with challenging and diverse materials, such as various wood species Patented die mounting system providing: Optimal coaxial alignment of rotating parts, reducing vibration Increased durability of mechanical components, allowing for reduced maintenance costs Fast and easy die replacement The free-rotation die function enables the operator to safely adjust the position of the rollers Instruments for measuring vibrations and temperature of bearings and rollers, preventing jamming Toothed belt transmission ensuring precision, efficiency, durability, and reduced maintenance costs Lubricant consumption reduction device, enabling significant savings Knives for reducing the length of material for wood processing Lsdpfeyyb Ddox Alnjaa Automatic roller positioning adjustment for animal feed production

Condition: new, Year of construction: 2026, Our best-selling briquetting press, the classic. + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Options for an extra charge: * Surcharge for the level indicator that enables automatic operation + € 995 net * Surcharge for large pre-compression chamber + 980 € (recommended for light material like straw) Briquette diameter: 50 mm Front bush: 50 mm Briquette stroke max .: 40 mm Briquette lift opt ​​.: 40 mm Throughput (depending on material): 30-60 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW 400 volts / 50 Hz / 3 phases Length: 1680 mm Width: 1100 mm Ledpegl Nlmefx Alnsaa Height: 1500 mm Weight: 680 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo content: approx. 0.7 square meters Pump: 27 liters Hydraulic pre-compressor Option cooling pressing tongs: no Hydraulic oil cooling option: yes Level monitoring option: yes CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Maximum chip length 15 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The customer must insure himself against loss of hydraulic oil - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: excellent (used), functionality: fully functional, HOT PRESS model COLOMBO REMO HPC 120 heating by with thermal oil second hand machine for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm. 90 max. thrust Ton. 120 intermediate worktop ( 3 worktops , 2 work compartments ) hydraulic pump motor power Hp 4 Laodpfx Aloq Slt Isnsa heating by with thermal oil weight kgs. 6000 volt. 380/50

Condition: excellent (used), functionality: fully functional, shelf length 3500 mm shelf width 1300 mm 8 hydraulic cylinders cylinder diameter 85 mm integrated oil heating Lsdpfx Aloyxwzconoaa power supply 380V

Condition: used, Gluer for slats Ljdpsyknlbefx Alnoaa

Condition: new, Year of construction: 2024, - Frame and edge press 1-sided/stationary - Useful dimension in mm as frame press 2630 x 1610 Lodpfx Alshd Nywsnoaa - Useful dimension in mm as edge press 3000 x 1610 - outer dimensions in mm 3200 x 2090 x 730 - Sturdy welded frame construction made of thick-walled profile tubes and laser-machined sheet steel parts ensure a torsion-free and dimensionally stable press base frame (no bolted frame parts!) - with left abutment, sliding carriage for width adjustment and central locking system and 2 hand hydraulic press units with Ergo handle - 3 vertical pressure beams type SK with roller bearings, made of strong-walled profile tube, galvanized, with hand hydraulic press units incl. Ergo handle. 20000 N pressing force, 60 mm stroke. Pressing units adjustable in 50 mm hole grid. - Lower abutment with fail-safe device, 5-fold adjustable in the hole grid. - Hold-down device with spindle press pressure - Chassis with 4 swivel castors (2 with brakes) - Powder coated (glue repellent) grey white RAL 9002 Pressure plate and abutment gentian blue RAL 5010 - Version Quattra 1-SK is equipped with comfort adjustment of the hand hydraulic press units and thus offers additional safety for the operator

Condition: new, Year of construction: 2026, Availability upon request Very robust machine with high pressing force - also suitable for producing briquettes of saleable quality *depending on the material. The large pressing cylinder and the 70 mm briquette make this possible. Our best-selling briquetting press series + Proven, simple technology for extremely low susceptibility to errors + 25 years of experience, further development, and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Supplement for demonstration cooling unit + €4,980 net, Lajdpfxjd Nm Sie Alnja (can also be retrofitted later) * Cools the pressing tongs (important for use after 4 hours) and the hydraulic oil * Cooling unit recommended for regular use of more than 4 hours at a time. Tariff number: 84793010, Briquette diameter: 70 mm, Front bushing: 125 mm, Max. briquette stroke: 100 mm, Optional briquette stroke: 80 mm, Capacity (depending on material): up to 150 kg/h* *depending on bulk density, *based on a bulk density of 200 kg per cubic meter. . Motor power: 9.2 kW, 400 volts / 50 Hz / 3-phase, Length: 2095 mm, Width: 1300 mm, * with large chamber 1600 mm Height: 1700 mm, Weight: 1250 kg, Oil capacity: 220 liters, Silo diameter: 1200 mm Silo capacity: approx. 1 cubic meter Pump: 75 liters Hydraulic pre-compressor Cooling option for pressing tongs: yes, with optional coolable pressing tongs Cooling option for hydraulic oil: yes Cooling of the pressing tongs and hydraulic oil with a cooling unit (optional accessory) Level monitoring option: yes Extruded briquette option; Yes (depending on material) Optional enlarged feed slide: Yes, with special accessory enlarged feed slide CE compliant Raw material requirements: - The moisture content (dry) must be between a minimum of 6% and a maximum of 18% - Maximum chip length: 20 mm - Installation temperature: Temperature-controlled room at a minimum of +5°C - The feed must be free of metals and mineral contaminants such as sand, stones, etc. This may result in damage to the press tools and/or increased wear.

Condition: new, Year of construction: 2026, operating hours: 8 h, Very robust machine with high pressing force - is also suitable for producing a salable briquette quality * depending on the material. The large press cylinder and the 80 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for cooling unit + € 4.995 net, (can also be retrofitted later) * cools the pressing tongs (important from 3.5 hours) and the hydraulic oil * Cooling device recommended for regular use of more than 3.5 hours at a time. Briquette diameter: 80 mm Front bush: 125 mm Briquette stroke max .: 100 mm Briquette lift opt ​​.: 80 mm Output (depending on material): up to 200 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Motor power: 9.2 kW 400 volts / 50 Hz / 3 phases Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Ljdpjxfwdjfx Alnjaa Silo diameter: 1200 mm Silo content: approx. 1 qbm Pump: 75 liters Hydraulic pre-compressor Cooling pressing tongs option: yes, with special accessory coolable pressing tongs Hydraulic oil cooling option: yes Cooling of the pressing tongs and the hydraulic oil with cooling device (special accessory) Level monitoring option: yes Strand briquette option; yes (depending on material) Option of enlarged filling slide: yes, with special accessory enlarged filling slide CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: as good as new (ex-display), Year of construction: 2025, Machine for sale at a special price Another machine, available immediately (ex works Neckartailfingen) * Including 1 year warranty. Your advantages: + Very robust, simple technology + Top price-performance ratio + Suitable for continuous operation + Long-standing, well-functioning / established machine Including control cabinet with timer operation Press is switched on manually and then runs until the time set on the timer (e.g. 4 hours) has elapsed. Then the press switches off. Technical data: Briquette dimensions: approx. 30 x 30 mm (square), Briquette length: 5-40 mm *depending on material Throughput capacity: up to a maximum of 20 kg/h. *depending on material Machine dimensions approx. 137 x 75 x 148 cm (length x width x height), Weight of the machine: approx. 250 kg, Capacity of the silo: approx. 250 liters, Motor: 2.2 kW, 400 V - 50 Hz, Noise emission: 62 dB, Raw material requirements: -Wood chips and dust smaller than 15 mm in length -Moisture content less than 18 % ATRO Lodpsd Nnwljfx Alnsaa -Sand, stones, metals and minerals increase wear --- Options at extra charge: --Timer function + 490 € net Machine is started manually and switches off automatically after a set time X. -Level indicator for automatic operation + 1450 € net Press starts and then stops automatically * NEW !!! Also available in 230 Volt, Motor then 3 kW instead of 2.2 kW, Surcharge + 890 € net (delivery time then approx. 8 weeks) - Special pressing units + 2.950 € net ---

Condition: as good as new (ex-display), Year of construction: 2026, Machine available at special price Machine available immediately (ex works Neckartailfingen) Demonstration unit Your benefits: + Very robust, simple technology + Excellent price-performance ratio + Suitable for continuous operation + Long-established, reliable machine Including control cabinet with timer operation The press is switched on manually and will run until the set time on the timer (e.g. 4 hours) has elapsed. After that, the press switches off automatically. Technical data: Briquette dimensions: 30/35 mm (square), Briquette length: 5–35 mm (depending on material) Throughput capacity: up to max. 25 kg/h (depending on material) Machine dimensions (approx.): 137 x 75 x 148 cm (L x W x H), Machine weight: approx. 250 kg Silo capacity: approx. 250 liters Motor: 2.2 kW, 400 V, 50 Hz Noise emission: 62 dB Raw material requirements: - Wood shavings and dust less than 15 mm in length - Moisture content less than 15% ATRO - Sand, stones, metals, and minerals increase wear --- Optional upgrades (at extra cost): - Timer function + €490 net Machine is started manually and switches off automatically after preset time X. - Level sensor for automatic operation + €1,450 net Press starts and stops automatically * NEW! Now also available in 230 Volt version Lsdpefci D Aefx Alnjaa Motor then 3 kW instead of 2.2 kW Surcharge + €690 net (delivery time approx. 8 weeks) ---

Condition: used, pressing force: 65 t, table width: 1,100 mm, table length: 2,200 mm, total length: 2,600 mm, total width: 1,300 mm, total height: 2,000 mm, overall weight: 2,800 kg, empty load weight: 2,800 kg, cylinder diameter: 80 mm, opening width: 300 mm, plate width: 1,100 mm, space requirement height: 2,000 mm, space requirement length: 2,600 mm, space requirement width: 1,300 mm, transport length: 2,600 mm, transport width: 1,300 mm, transport height: 2,000 mm, No. 04486 Veneer press Ott JU 60 Used Heating plates 2200 x 1100 mm LW Plates gold anodized, in very good condition Electric heating 2x 6 kW 4 hydraulic cylinders, diameter 80 mm each Total pressing pressure 65 tons Specific pressing pressure at full capacity 2.7 kg/cm2 Opening width 300 mm Button control for close - open - stop Circumferential emergency stop safety pull cord Transport dimensions approx. 2600 x 1300 x 2000 mm LWH Weight approx. 2800 kg To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Ledpfxsyfw D As Alnjaa Technical specifications, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex warehouse

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, table width: 4,200 mm, table length: 1,300 mm, HOT PRESS FOR EDGE-GLUED PANELS ORMA MOD. LS 42/13 AS / BO – CE RULES - N. 10 press cylinders - N. 5 platen cylinders - N. 8 front cylinders Laedpsywcg Ijfx Alnoa - Top-down pressing system - Continuous working capability - 45 kW diathermic oil boiler - Platen dimensions 4200 x 1300 mm - Complete with loading/unloading system - 250 mm glue spreader - Year 2005

Condition: excellent (used), Shelf length 2500 mm Shelf width 1300 mm Laedpfoyw H H Sex Alnja 4 hydraulic pistons Clearance 400 mm Water heating

Condition: used, Year of construction: 2025, New demonstration machine! MOVE — the high-precision vacuum press with gigantic usable area for vacuum lamination and vacuum veneering of curved workpieces. Offers extensive flexibility thanks to absolute mobility and a revolutionary folding mechanism that reduces the footprint to 45% when folded. High-precision vacuum press with folding lid, including: - Revolutionary folding mechanism (reduces footprint to 45%) - 40 m³ high-performance vacuum pump (up to 900 mbar (9 t/m²)) by BECKER - Optional automatic shut-off when pressure is reached (especially for large vacuum volumes) - Pressure regulation: 400 to 900 mbar, analog vacuum gauge - Highly elastic natural rubber membrane (up to +130 °C) - Quick-change membrane system - Robust phenolic resin work surface (up to +120 °C), 15-ply bonded - Gas struts for lid opening - Vacuum gauge - Connection for external vacuum bag - Smooth-running swivel castors - FESTO pneumatics and SIEMENS electrical components Technical specifications and dimensions: - Usable area: approx. 3050 x 1350 mm - Inner frame dimensions: approx. 3130 x 1430 mm - Total dimensions: approx. 3700 x 1700 x 1100 mm - Total dimensions (folded): approx. 3700 x 770 x 1780 mm - Electrical connection: 1~, 0.8/1.0 kW, 230 VAC +/- 10%, 50/60 Hz - Weight: 670 kg Laedpfx Aeyi Hd Holnsa Location: Rieth

Condition: as good as new (ex-display), Year of construction: 2024, new heating plate press, hydraulic ITALPRESSE type XL/6 30-13 with gold anodized plates Touch display control - electric heating plates 3.000 x 1.300 mm - Total pressure 90 to. - Number of heating plates 2 pcs. - Number of shelves 1 pc. - Cylinder stroke 350 mm - Shelf opening 350 mm - Loading from all sides - Number of impression cylinders 6 pcs. - Diameter of pressure cylinders 85 mm - Power requirement of hydraulic unit 3 kW - Electric heating plates made of solid hard aluminum with built-in heating wires - Heating capacity 22 KW - High-pressure insulating plates - Working temperature 90° C. - max. temperature 120° C. - Operating voltage 400 V/50 Hz - Safety regulations according to CE standard Standard equipment: - Movement of the press table with rack and parallel guides at 2 corners of the press table made of self-lubricating material - Touch screen electronic control unit for controlling and monitoring the machine - Digital timer for setting the pressing time and automatic opening - Digital input and monitoring of the pressing pressure - Digital timer for setting the pressing time - Digital diagnosis and display of fault messages - Safety circuit with two-hand operation - Safety rip cord Lajdpfxjdx R Tfe Alnoa - Safety bracket for lower pressing table Integrated accessories: - Touch Screen TS/400 - EFC electronic flatness control - Gold anodized heating plates (Busse) Location: From stock 54634 Bitburg - immediately available-

Year of construction: 2008, condition: excellent (used), Electric heating element Shock- and impact-proof plug-in heating system with heating conductors embedded airtight in silicone.No wear, no corrosion, operational safety even in continuous operation and in case of impacts and shocks. Temperature adjustment via integrated controller with insulated control knob. Permanently connected industrial cable, no vulnerable plug connections. High-strength special aluminum profile for high load capacity and flat pressing surfaces on all sides. Gold anodized finish as standard, scratch and abrasion resistant, easy to clean. Size:Type: EST 21 Laodolcd Szspfx Alnoa Length: 2100 mm Connected load: 1100 Watt, 230 Volt Temperature: 0 / 40 / 70 / 100 / 170 / 200 degrees Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2026, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second Laedpfxow Sgnkj Alnja - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice