Used roll benders (motor-driven) for sheet thickness over 14mm for sale (120)

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles Bdjdpjh U Rzgofx Aaaja CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Year of construction: 1991, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1991 Specifications Metric US Standard Rolling width 3000 mm Rolling thickness 3x toproll Ø 120 mm Rolling thickness 5x toproll Ø Bdjdpfxjkwcc Ns Aaaea 150 mm Rolling thickness prebending 100 mm Top Roll Ø 910 + 820 + 740 mm Bottom Roll Ø 940 mm Side roll Ø 780 mm Number of rolls 4 Rolling speed 2 + 4 Adjustiment lower roll 200 mm/min. Adjustment side rolls 500 mm/min. Number of driven rolls 2 Power 300 kW Dimensions (Estimate) Length 8000 mm Width 5400 mm Height 5400 mm Weight 290000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Share on

Year of construction: 2007, condition: good (used), Make: HAEUSLER Type: Clamp Year: 2007 Specifications Metric US Standard Min. shell inner diameter 1800 Max. shell inner diameter 5500 Min. shell outside diameter 1500 Max. shell outside diameter 2500 Minimum wall thickness 10 mm Maximium wall thickness 40 mm Max. section weight 15 T Max. weight total workpiece 60 T Dimensions (Estimate) Length 24000 mm Width 6000 mm Height 3200 mm Weight Bdodpfxskwcn Ee Aaaea 0 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1980, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1980 Specifications Metric US Standard Rolling width 3000 mm Rolling thickness 3x toproll Ø 130 mm Rolling thickness 5x toproll Ø 140 mm Rolling thickness prebending 120 mm Top Roll Ø 950 mm Bottom Roll Ø 850 mm Side roll Ø 180 mm Number of rolls 4 Bdsdpfxokvm Sze Aaasa Rolling speed 2 + 4 Adjustiment lower roll 0 - 400 mm/min. Adjustment side rolls 0 - 400 mm/min. Number of driven rolls 2 Power 132 + 37 kW Dimensions (Estimate) Length 12000 mm Width 5440 mm Height 5650 mm Weight 286000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1978, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1978 Specifications Metric US Standard Rolling width 3050 mm Rolling thickness 3x toproll Ø 60 mm Rolling thickness 5x toproll Ø 70 mm Rolling thickness prebending 50 mm Top Roll Ø 630 mm Bottom Roll Ø 600 mm Side roll Ø 500 mm Number of rolls 4 Rolling speed 0 - 5 Adjustiment lower roll 200 mm/min. Adjustment side rolls 200 mm/min. Number of driven rolls 2 Power 120 kW Dimensions (Estimate) Bodokvm S Nepfx Aaajda Length 5790 mm Width 4200 mm Height 4200 mm Weight 85000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1994, machine/vehicle number: 10659, roller (bottom) diameter: 300 mm, roller (top) diameter: 350 mm, working width: 3,000 mm, sheet thickness (max.): 25 mm, empty load weight: 24,000 kg, TECHNICAL DETAILS Number of rollers: 4 pcs Max. sheet thickness: 25 mm Max. working width: 3,000 mm Upper roller diameter: 350 mm Lower roller diameter: 300 mm MACHINE DETAILS Bedpfxoyua Ezs Aaaoda Control: Conventional Dimensions & Weight Dimensions (L x W x H): 6,300 x 2,000 x 1,800 mm Unladen weight: 24,000 kg Transport packages: 1 pc.

Condition: good (used), functionality: fully functional, Year of construction: 1978, machine/vehicle number: 4303, working width: 3000 mm metal sheet thickness: 15 mm metal sheet thickness when bending: 10 mm Bdodpfxsd D Nxxs Aaasa upper roller-Ø: 320 mm below roller-Ø: 310 mm working speed: ca. 5,5 m/min electrical connection: 380 V kW weight: ca. 17000 kg space needed: 5450 x 2100 x 2450 mm

Year of construction: 2018, condition: good (used), Make: FACCIN Type: 4HEL 3590 Control: Siemens TOUCH Year: 2018 Specifications Metric US Standard Rolling width 3500 mm Rolling thickness 3x toproll Ø 80 mm Rolling thickness 5x toproll Ø 110 mm Rolling thickness prebending 90 mm Top Roll Ø 900 mm Top Roll Ø 900 mm Bottom Roll Ø 800 mm Side roll Ø 600 mm Number of rolls 4 Rolling speed 0-6 Adjustiment lower roll Bdsdpfskvm Nfex Aaaoa 0-200 mm/min. Adjustment side rolls 0-400 mm/min. Top support yes Side supports yes Number of driven rolls 2 Power 90+75+9 kW Dimensions (Estimate) Length 4430 mm Width 8800 mm Height 11000 mm Weight 178000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: like new (used), functionality: fully functional, Year of construction: 2025, machine/vehicle number: M3022, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: Delsy, controller model: Digital readout, number of rollers: 4, roller (bottom) diameter: 330 mm, roller (top) diameter: 350 mm, side roll diameter: 260 mm, roller diameter: 400 mm, roller length: 3,000 mm, working width: 3,100 mm, working height: 900 mm, sheet thickness (max.): 22 mm, sheet thickness steel (max.): 22 mm, sheet thickness stainless steel (max.): 22 mm, sheet thickness aluminum (max.): 30 mm, overall weight: 13,000 kg, power: 10 kW (13.60 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, hardened rollers, swiveling upper roller, Bending capacity with dual Initial pinch planetary plate width 3000 mm thickness 22 mm pre-bend 18 mm --- Length on the rolls 3100 mm top roll 350 mm Bodpoid Al Njfx Aaaeda lower roll 330 mm Power electric 20Hp Vac 400/50 Installed configuration Hardened surface of the 4 rolls Driven central rolls rotation hydraulic motorized with gear units Synchronized hydraulic rotation between the rolls Rolls parallelism lifetime set with torsion bar Conical plate bend hydraulic attachment Calibration re-rolling feature for welded shells Front open drop-end to unload the closed rolled plates. Control console electric commands with digital readout Safety and emergency systems installed Manuals and schematics originals

Year of construction: 1980, condition: good (used), with initial rounding Technische Daten:/ technical details Biegelänge / bending lenght 2000 mm max. Blechstärke / max. sheet thickness 20 mm Bdjdpfx Aaekzg E Aoaoa Anbiegeleistung / initial rounding 15/11 mm Walzendurchmesser Unterwalzen / roll diameter below rolls 280 mm Oberwalzendurchmesser / diameter of the upper roll 300 mm Antriebsleistung Hauptantrieb / drive capacity main drive 16,2 kW Antriebsleistung Anstellantrieb Oberwalze / drive capacity upper roll 4,8 kW Antriebsleistung Anstellsntrien Unterwalze / drive capacity below roll 3,7 kW Gewicht ca. / weight ca. 14200 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2017, machine/vehicle number: 25498, roller (bottom) diameter: 320 mm, roller (top) diameter: 320 mm, side roll diameter: 260 mm, working width: 2,070 mm, sheet thickness (max.): 25 mm, TECHNICAL DETAILS Sheet width: 2,070 mm Sheet thickness: 25 mm Bending capacity: 18 mm Top roller diameter: 320 mm Side roller diameter: 260 mm Lower roller diameter: 320 mm MACHINE DETAILS Total power supply: 26 kW Dimensions & Weight Space requirement: approx. 4,700 x 2,000 x 2,200 mm Machine weight: approx. 8,100 kg EQUIPMENT Bdsdjygw Ikspfx Aaasa Hydraulic lateral roller adjustment Conical bending device 2 driven rollers Hardened rollers Hydraulic drop-end bearing Mobile control panel Foot switch Safety device CE marking

Condition: new, Ostas 4-Roll Plate Bending Machine 4R OHS 2570 x 275 Hydraulic Side Roll Positioning 3 Digital Displays Hydraulic Drop-End Hardened Rolls Cone Bending Device Separate Control Console Roll Length: 2570 mm Bedpfx Aasxrdn Hjaoda Top Roll Diameter: 275 mm Side Rolls Diameter: 220 mm Total Motor Power: 16.5 kW Weight: 9500 kg Dimensions (mm): 5350 x 1750 x 1950 (L x W x H) Bending Performance Data 16 mm at minimum inside diameter (5 x top roll) 12 mm at minimum inside diameter (1.5 x top roll) Pre-bending Performance Data 12 mm at minimum inside diameter (5 x top roll) 10 mm at minimum inside diameter (1.5 x top roll) All bending capacities are based on 250 N/mm2 yield strength Material (ST 37 – ST 42 structural steel) The images shown are for illustration purposes only.

Condition: used, functionality: fully functional, actuation type: hydraulic, roller (top) diameter: 420 mm, sheet thickness (max.): 25 mm, Hydraulic cylinder Bdjdpfx Aasydk D Hsaoa Brand: Casanova Bending length: 3,100 mm Maximum bending thickness: 25 mm Top roller diameter: 420 mm The side rollers are raised parallel, without inclination. New control and command panel, installed and modified in 2003. Equipped with hydraulic flag and hydraulic side table. Pit dimensions: - 200x6800 mm - 555 mm depth

Condition: good (used), Year of construction: 1993, machine/vehicle number: 9340020, Offer 26035 Technical Data - Three powered rollers, each roller hydraulically adjustable - Suitable for prebending and cone rolling, side arms can be swung out - Operation from a swiveling control panel with digital actual value displays - Max. working width: 3050 mm - Max. plate thickness at 400 N/mm² yield strength without prebending: 20 mm - Prebending at minimum bending diameter 5 x top roller diameter: 16 mm - Top roller diameter: 340 mm - Side roller diameter: 250 mm Bdsdpoyq E S Eefx Aaaea - Bottom roller diameter: 300 mm - Drive: 400 V / 9.5 kW - Working speed adjustable - Space requirement: approx. W 6200 x H 1650 x D 1650 mm - Machine weight: approx. 16,000 kg - Total weight (machine + support column + support arm): 19,500 kg - Includes: extended roller ends for mounting profile rollers, - conical bending device - lateral support arm hydraulically adjustable - upper support column hydraulically adjustable

Condition: new, bending length: 2100sheet thickness: 45prebending: 35Upper Roll Diameter: 430Side Roll: 390motor: 30messurements (LxWxH): 5200 x 2200 x 2500weight approx.: 19000 Technical specifications: Bedjytyy Njpfx Aaasda - Hardened and polished rolls - Conic bending device - Digital readout for side rolls - Complete body made of ST-52 Steel - Portable control panel separated form machine - Rolls are mounted with bearings - Top roll cover, openable and closeable by hydraulic, controlled from control panel. - All rolls are driven by hydraulic motor and planetary gearbox - Side rolls upwards downwards movements are hydraulic powered

Year of construction: 2002, condition: excellent (used), Technical data: Bdodpfx Aasittzfjaoa working width: 3550 mm max. bending capacity: 42,0 mm max. bending: 35,0 mm CNC control diameter upper roller: 480 mm diameter 2nd top roller: 540 mm diameter lateral side rollers: 480 mm diameter middle bottom roller: 480 mm conical bending device by inclination of the two side rollers mobile control panel with digital display hydraulic folding bearings own weight: approx. 44 tons additional equipment: lateral bending aid swiveling bending aid on top additional top roller The seller is not liable for writing or data transmission errors. The machine is in appearance, technique and wear according to the age; used machines are sold without any warranty.

Condition: excellent (used), functionality: fully functional, Year of construction: 2017, control type: manual, degree of automation: manual, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 380 mm, roller (top) diameter: 430 mm, side roll diameter: 300 mm, roller diameter: 480 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 1,420 mm, sheet thickness (max.): 35 mm, sheet thickness steel (max.): 35 mm, overall weight: 20,000 kg, total length: 5,500 mm, total width: 2,000 mm, total height: 2,100 mm, power: 20 kW (27.19 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 3, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, model capacity 3000x35 mm Digital readout Hydraulic 4 roll plate bending machine, used year 2017 plate thickness rolling 35 mm pre-bend 30 mm minimum rolling diameter ID 480 mm plate max width on the rollers 3100 mm top roll size 430 mm Power on hydraulic unit 20kW Vac 400/50 -480/60 Installed configuration Hardened rolls high surface strength Conical plate rolling, cone bending Electric console remoted Digital position readout Hydraulic rotation central rolls driven parallelism lifetime with torsion bar Pre-pinch load adjustable for pre-bending Drop-end top roll front open for unloading Bjdpfxoyu Nr Do Aaajda Re-rolling system for welded shells calibration. Safety and emergency stop Manuals and schematics – CE declaration of quality machine dimension 5500x2000x2100 mm weight 20ton --- Additional accessories installed with the machine See layout drawing in enclosed nr.1 central support hydraulic 4 ton capacity to support large shell dia up to 4,5 meters id nr.1 side support hydraulic left side 4 ton doble arm nr. 1 side support hydraulic right side 4 ton double arm

Condition: new, bending length: 4100sheet thickness: 25upper roll diameter: 460motor: 22messurements (LxWxH): 7200 x 2500 x 2200 mmweight approx.: 31000sheet length: 4100CY3R-HHS 460-40/25 – 3-Roll Hydraulic Plate Bending Machine Cone bending device for precise bending Induction-hardened rolls for long-lasting durability Digital display on both side rolls Robust machine body made of ST-52 steel construction Separate control panel for convenient operation All rollers mounted on bearings for smooth performance Bedpfed Ab Spjx Aaajda Drop end controlled from the control panel, allowing easy release of bent metal sheets and lifting of the upper rolls Roll movement and parallelism adjustment fully controlled via the control panel All rolls driven by separate hydraulic motors with planetary gearboxes CE-compliant, meeting European safety standards

Condition: new, sheet length: 2100sheet thickness: 40prebending: 30Upper Roll Diameter: 390Side Roll: 360motor: 22messurements (LxWxH): 4900 x 1950 x 2200weight approx.: 17000 Technical specifications: - Hardened and polished rolls - Conic bending device Bsdpfxed Ab Syo Aaajda - Digital readout for side rolls - Complete body made of ST-52 Steel - Portable control panel separated form machine - Rolls are mounted with bearings - Top roll cover, openable and closeable by hydraulic, controlled from control panel. - All rolls are driven by hydraulic motor and planetary gearbox - Side rolls upwards downwards movements are hydraulic powered Options: - variable rotation speed EURO 3.682.00 Material feed table on request Oil cooler EURO 1,040.00 Center support EURO 11.900,00 Side supports EURO 8.250.00 We have many references!

Condition: new, neu ca. 12 - 14 Wochen ab Auf Türkei 98600 € 1863.54 € 3100 mm 16 mm 16 mm 13 mm 16 mm 14 mm 12 mm 300 mm 300 mm 240 mm 50 mm 1140 mm 18.5 kW 5310 mm 1660 mm 1140 mm 11100 kg 4 rolls fully hydraulic drive of upper and lower roll (from 30 mm bending capacity all four rolls) by planetary gear box hydr. side rolls positioning with electronical synchronisation hydr. lower roll feed with mechanical synchronisation adjustable pinching pressure variable rolling speed hardened rolls conical bending device hydraulic drop-end bearing moveable control panel overload protection user manual in GERMAN or ENGLISH according to CE rules OPTIONAL: Bedjynm Hfjpfx Aaasda NC control upper and lateral supports IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 103100 € 1948.59 € 2550 mm 25 mm 25 mm 20 mm 20 mm 16 mm 350 mm Bdodpfjynm Eujx Aaasa 350 mm 260 mm 1,5-5 m/min 22 kW 5500 mm 2000 mm 1900 mm 13000 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT: infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommended

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei 97400 € 1840.86 € 2050 mm 30 mm 30 mm 25 mm 25 mm 20 mm 350 mm 350 mm 260 mm 1,5-5 m/min 22 kW 5000 mm 2000 mm 1900 mm 11000 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules Bodpoynm Ensfx Aaaeda OPTIONAL EQUIPMENT: infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommended

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 53700 € 1014.93 € 2050 mm 16 mm 16 mm 13 mm 13 mm 10 mm 260 mm 260 mm 200 mm 1,5 / 6 m/min 7.5 kW 4300 mm 1600 mm 1550 mm 6100 kg 4 rolls Top rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan system Pinch roll and latereal rolls move with hydraulic cylinders Digital read-out for lower and side rolls position Hardened rolls Conical bending device Hydraulic load relieving of upper roll Bdedoynm Ehjpfx Aaasa Hydraulic drop-end bearing 2 working speeds Protectionagainst overload Moveable control pane According to CE rules OPTIONAL EQUIPMENT: Infinitely adustable speed of rolls Hydraulic side support Hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: The max. sheet metal thickness isequivalent to 50 % of nominal capacity The cone length can be max. 30 % oremust be more than 60 % of roll length Hardened rolls are recommended

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 111500 € 2107.35 € 3100 mm 20 mm 20 mm 16 mm 16 mm 12 mm 350 mm 350 mm 260 mm 1,5-5 m/min 22 kW 6000 mm 2200 mm 1900 mm 15000 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT: infinitely adustable speed of rolls Bodpfjynm Ebjx Aaajda hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommended

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei 73200 € 1383.48 € 2050 mm 20 mm 20 mm 16 mm 16 mm 12 mm 280 mm 280 mm 220 mm 1,5 / 5 m/min 16.5 kW 4350 mm 1700 mm Bdsdoynmylepfx Aaaea 1850 mm 8550 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT (PRICES ON REQUEST): infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommended