Condition: reconditioned (used), No.: 2587 1 used, functionally tested pelletizing-extrusion line, output approx. up to 600 kg/h depending materials, equipped with: 1 volumetric material blender ( Dosing unit ) Extruder Plastmachines Type PME 100 Single-screw Ø 100 mm – 35 L/D Motor 134 kW – DC 1x venting port Melt-Filter BKG Type K-SWE 121 RS – back-flush self-cleaning incl. Fs Ia Soh Eydbjfmrspg Hydraulic pack 3 kW Strand die-head with holes 20 x Ø 3,5 mm Strand cooling bath 00 x 4000 mm incl. strand guiding rollers Strand blower Strand pelletizer SG 3000 ResoTec Control cabinet Inspection visit shortly possible, date by appointment. More extrusion lines ex our Workshop / stock Wuppertal - Germany available.

Condition: used, Year of construction: 2006, operating hours: 3,459 h, fuel: diesel, Year of manufacture: 2006 Colour: Green Fs Ijwazgfea Sfmrepg Field of application: Construction Drive: Wheel Empty weight: 6.500 kg CE mark: yes Komptech Hurrikan. Year: 2006. Hours: 3459. Max weight: 6500 kg. CE Machine. Axle load: 600 kg Alko axle. 53 KVA. 400 V 63 A. New Perkins diesel engine. Tyres: 285/70R19,5 80%. German Machine including german street registration! ID NR: 391. The General Terms and Conditions of Heinhuis are applicable to all adverts, offers and quotations by Heinhuis, all agreements entered into by Heinhuis and the negotiations preceding them. By any form of response you accept the applicability of the General Terms and Conditions of Heinhuis and you declare that you have taken note of these General Terms and Conditions. Our prices are export netto prices.

Year of construction: 2019, Condition: used, Functionality: unexamined, Selector 400 Basic Package Spiral Wave Screen Deck AA209-150 - 20 Waves Fps Iasv Sqg Hs Sfmreg

Condition: good (used), Baler HSM V-Press 504 waste paper press Machine in perfect condition, like new. Machine purchased from a warehouse, unused. Description: -HSM TCS (TorsionControlSystem) for controlling the inclination of the press plate Modern microprocessor control with membrane keyboard and graphic text display Suitable for both cardboard and foil Automatic start of the pressing process after closing the door Massive pressure plate and extremely stable pressure plate guide To fill the press, the upper half of the door opens to the right Door lock with knee lever for quick and safe door opening Manual bale strapping with polyester tape Pressure force: 40 kN Specific pressure force: 11.2 N/cm2 Drive power: 1.1 kW Voltage frequency: 230V / 50Hz Idle cycle time: 27 sec. Press capacity at idle speed (theor.): 3.75 m3/h Fill level: 661 mm Width x height of filling opening: 700 x 470 mm Bale length x bale width x bale height: 700 x 500 x 600 mm Bale weight: 60 kg Fps Iaewh Nqbs Sfmrog Width x depth x height: 1020 x 812 x 1922 mm Weight: 290 kg Related product line: V-Press Consumable type: strapping tape

Condition: excellent (used), Year of construction: 2019, operating hours: 8,000 h, Functionality: fully functional, machine/vehicle number: REFLEX 36290, cutting force: 650 t, power: 200 kW (271.92 HP), net weight: 56,280 kg, tool mount: 800 mm, filling weight (max.): 2,950,000 g, total width: 2,550 mm, total length: 15,176 mm, total height: 3,655 mm, overall weight: 62,080 kg, type of input current: three-phase, operating pressure: 315 bar, pressure: 350 bar, construction width: 4,290 mm, This is a fully functional machine that will be ready for delivery in December 2025. It includes a loading table - it has dimensions of 6000 * 2500 mm. The length of the chamber is 6000 mm. The expected status as of December 31, 2025 will be approximately 8,800 hours. The machine is located at: U Panelárny 461, Předměřice nad Labem. Fpj Iowhnbfea Sfmreg

Year of construction: 2018, operating hours: 7,255 h, Condition: good (used), machine/vehicle number: 75070, Mnr. 75070 / Screen with 3 fraction - Fine fraction (mm): 0/10…25, Medium fraction (mm): 10…25/60…90, Coarse fraction (mm): 90…120 / 75 kV/A diesel generator / hopper volume: 7 m3 / filling height (mm): 3.450 / filling length (mm): 3.750 / max. discharge height medium fraction (mm): 3.500 / max. discharge height coarse fraction (mm): 2.850 / weight ca. 21 to / transport length (mm): 11.500 / transport width (mm): 2.250 / transport height (mm): 4.000 / throughput Fo Ia Sogrn Acofmrspg depending on type of material till ca. 200 m3/h / ca. 6.000 h electric driven /

Condition: reconditioned (used), stock-No. 2452 1 used, partly overhauled and functionally tested pelletizing line capacity up to 500 kg/h depending material, equipped with: Kreyenborg Force-feeder SW 100, motor 7,5 kW Extruder BKG single-screw Ø 100 mm – 35 LD, motor 132 kW – AC Screw speed up 143 r.p.m. screw depth 14 mm Fpo Ia Sed Sg I Iofmrjg heating power installed 35 kW 1x athm. venting port ( vacuum-pump optional ) Kreyenborg K-SWE 160 RS screen-pack-changer back-flush self-cleaning with filter surface 244 cm² BKG underwater pelletizing unit AH 300, complete with : diverter-valve , hydraulic unit pelletizer, motor 4 kW incl. die-plate and knife-holder Water pump 2,2 kW By-Pass System, Process water tank heating power 9 kW Heat-exchanger BKG pellet spin-dryer TWE 300 with motor 3 kW pellet classifier sieve control-board and Siemens Touch operation panel (updated ) OPTIONAL against additional price ᐳ * Vacuum pump ᐳ ,material feed conveying, Big-Bag filling Station ᐳ chiller – cooling unit More pelletizing lines ex workhop Wuppertal-Germany available, ask for our most recent machine-stock-list or visit us, you´re welcome.

Condition: ready for operation (used), Year of construction: 2002, operating hours: 13,400 h, Technical specifications of horizontal automatic Press Model Konti 275 D Manufacturer: PAAL, Germany Press force: 75t Channel cross-section 75x110 cm. Feed opening 102x155 cm. Filling volume approx. 2.0 m3 Binding vertically 5 wires Drive power 37 kW Material throughput • Density 35 kg/m3 9.5 tonnes/hour. • Density 60 kg/m3 16.5 tonnes/hour. • Density 100 kg/m3 26 tonnes/hour. Bale weight from 500 to 750 kg. Adjustable bale length Bale size (WxH) 75 x 1100 mm Press weight 25 tonnes Press dimensions see brochure Fps Ijwb H Tgja Sfmrog Year of manufacture 1997. Operating hours, approx. 40,000 hours

Year of construction: 2021, Condition: ready for operation (used), Functionality: unexamined, Basic package Selector 800 Lower belt BB 1350 mm AA 6.4m -profiled belt- Fo Ia Sfmjvm Upnerjpg SPIRAL SHAFT SCREEN COVER AA254-150 - 16 shafts

Year of construction: 2010, Condition: excellent (used), Various sieves / perforated plate mostly unused For Alpine granulators type 63/100 Ro and type 80/100 Ro Fj Iajd Shklo Sfmrspg e.g. for 80/100Ro 11 pieces 2 mm round hole 19 pieces 2,5 mm round hole 29 pieces 3 mm round hole 15 pieces 3.5 mm round hole + various different perforations 5mm round hole, 6 mm square, 3mm round hole for 63/100 + many other sizes, just ask us for your desired size

Condition: new, WAM FLO dust collector extraction filter cabinet filter extraction installation New Motor power fan 3kW 3000rpm Filter surface 22m2 Equipped with electro-pneumatic cleaned cartridges Stainless steel 304 Zero dust emission 8 pieces in stock See our other advertisements VMA Wekerom Fpe Ia Sevcp Dfsfmreg

Year of construction: 2014, Condition: reconditioned (used), Screen with 3 fraction Fpo Ia Sfsd H E Iaemreg Fine fraction: 0/10...25 mm Middle fraction: 10...25/60...90 Coarse fraction: 60...90 mm Coarse fraction extended (mm): 90/120 / 64 kVA generator / possible in grid operation with 125A plug /

Year of construction: 1996, Condition: reconditioned (used), No.: 2590k 1 used compounding-pelletizing line – output up to 1200 kg/h depending material, equipped with: Extruder Twin-screw THEYSOHN Type TSK 90 Screws 2x Ø 90 mm – 36 LD co-rotating intermeshing Segmented screws-and Cylinder, Water / Medium cooled Extruder Motor 255 kW-DC / Screw speed up to 300 r.p.m. 1x Side feeding extruder TSD 75 twin-screw with 3 kW 3x venting ports 1x Melt-Filter No. 1 type K –HS- Y sieve/Mesh 176 mm incl. Hydraulic Pack 1x Melt-Pump with motor 22 kW 1x Melt-Filter No. 2 type K-SWE 180 RS back-flush self-cleaning 1x Strand die-head with holes 32 x Ø3,5 mm 1x Strand cooling bath 620 x 5000 mm 1x Strand pelletizer SG 300 with 11 kW ResoTec Monitor control Board Fpo Iasgbffvj Sfmrjg Inspection visit / demonstration shortly possible - date on appointment You´re welcome. More compounding pelletizing lines ex pour workshop available, > find our most-recent stock-list online on our homepage.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, Functionality: fully functional, pressing force: 100 t, bale weight: 1,400 kg, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale height: 1,100 mm, bale width: 1,100 mm, overall weight: 36,000 kg, oil tank capacity: 1,300 l, nominal current: 238 A, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Fpe Ia Sovf E Avefmreg Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: good (used), Year of construction: 2018, operating hours: 4,620 h, Axtor 10 / machine number: 249037 / CAT C15 T4F Stage IV / 433 kW / 589 HP / Overbelt magnetic system / Radio remote control / Pre driving device / Shredding or chipping mode with free-swinging tools and chipper or shredder blades / Material: good for green waste, bark, round wood, slabs and waste wood / 2 drum speeds 460 / 810 rpm (modification for free swinging tools) / Drum width 1.543 mm / Drum diameter 1.108 mm / 32 knifes or tools / Weight: ca. 25 to / Feeding height: 2.800 mm / Screen baskets: 60x60, 80x80, 100x100, 125x125 ect. possible/ Screen baskets according to your wishes possible / Throughput depending on the material and feeding (operator) between 100 and 300 m3/h / Feeding hopper over 4 m long / noise emission: 122 dB (A) weight: ca. 25.000kg Transport dimensions: Fpj Iaod N Hpno Sfmreg length: 11.700mm width: 2.500mm height: 3750mm draw bar eye: 50mm

Condition: reconditioned (used), No.: 2587k 1 used, functionally tested pelletizing-extrusion line, output approx. up to 600 kg/h depending materials, equipped with: 1 volumetric material blender ( Dosing unit ) Extruder Plastmachines Type PME 100 Single-screw Ø 100 mm – 35 L/D Motor 134 kW – DC 1x venting port Melt-Filter BKG Type K-SWE 121 RS – back-flush self-cleaning incl. Hydraulic pack 3 kW Strand die-head with holes 20 x Ø 3,5 mm Strand cooling bath 400 x 4000 mm incl. strand guiding rollers Strand blower Strand pelletizer SG 300 Fe Ia Sfmoiyy I Njrepg ResoTec Control cabinet Inspection visit shortly possible, date by appointment. More extrusion lines ex our Workshop / stock Wuppertal - Germany available.

Condition: used, Technical data for the bale loosening drum: Manufacturer not known Type of bale loosening drum Year of manufacture not known Dimensions of the drum 6000 x 3000 mm (l x d) Height of the welded-in helix 300 mm Dimensions of the drum frame 4900 x 3400 x 2200 mm (L x W x H) Drive power 2 x 4 kW Fj Ia Sou Thx Rsfmrjpg Functional description: The bale loosening drum was fed with pressed paper bales from which the binding wire had previously been removed. The pressed and compact bale is broken up and loosened by the baffle plates welded into the drum parallel to the conveying direction. The helix, which is welded in with an incline to the conveying direction, transports the loosened material further to the drum outlet. Here it falls through a hopper onto a conveyor belt for further processing. Scope of delivery: Bale loosening drum Frame with drive and roller bearings for the bale loosening drum Comments: Documentation (operating instructions, CE declaration, electrical/hydrical circuit diagram) is not available and cannot be supplied. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Year of construction: 2021, operating hours: 988 h, Condition: like new (used), machine/vehicle number: 26236, diesel engine 55 kW / hopper volume 5 m3 / dimensions: L = 11.250 mm, W = 2.550 mm, H = 4.000 mm /simple drum change without tools / for all-purpose: compost, wood biomass, bark, sand, gravel, houshold and residual waste / weight: 16 t Fpe Ia Sfmoh Ea Dkjrsg

Year of construction: 2023, Condition: new, We offer, successfully since more than 12 years, installed in all over EU, our new compounding extruders/lines : e.g. Type Alphatec AD-.S 75 with: Segmented, Co-Rotating intermeshing, cylinder water / medium cooled Throughput performance up to 1000 kg/h - depending on the material Drive 132 kW - 250 kW L/D Ratio - according to processing needs Degassing zones - as desired Side feeder type ZS-B - as desired OPTIONAL: > Melt filter/screen changer > Pelletizing systems: strand ST- , water ring WRG or Underwaterpelletizing UWP Fs Ia Sod Hqa Isfmrspg > Screw configuration according to your needs > Material dosing: volumetric or gravimetric > further accessories Visit us at our Wuppertal plant.

Condition: good (used), Year of construction: 2021, operating hours: 5,871 h, machine/vehicle number: 447202, CAT® C13 / Motor Tier 4 Final, Stage V / magnetic separator / Bio cutting unit / Radio remote control / pre-driving device / Material: good for green waste, root stocks and all kind of residual and waste wood / central lubrication / weight ca. 25 to / basket screens: possible 80 mm round, 100 x 100, 125 x 125 mm or 250 x 250 mm square or size at customer´s option / 1.900 rph / drum length: 2.820 mm / drum speed: 1. gear 22 rpm, 2. gear: 34 rpm Fj Iajlbmmws Sfmropg

Year of construction: 2023, Condition: new, We offer, successfully since more than 12 years, installed in all over EU, our new compounding extruders/lines : e.g. Type Alphatec AD-.S 75 with: Screw diameter 73 mm Segmented, Co-Rotating intermeshing, cylinder water / medium cooled Throughput performance up to 1000 kg/h - depending on the material Drive 132 kW - 250 kW L/D Ratio - according to processing needs Degassing zones - as desired Fo Ia Sfmsi Dtbqorjpg Side feeder type ZS-B - as desired OPTIONAL: > Melt filter/screen changer > Pelletizing systems: strand ST- , water ring WRG or Underwaterpelletizing UWP > Screw configuration according to your needs > Material dosing: volumetric or gravimetric > further accessories Visit us at our Wuppertal plant.

Year of construction: 2017, operating hours: 5,355 h, Condition: refurbished (used), Trailer with 3 axles / Low-speed single-shaft shredder for all types of waste / High performance with bulky or household waste, sturdy construction and easy control make the Terminator an ideal waste processing machine / Hydraulic drive 5000 / CAT C13 Tier 4 Final/Stage Fe Ia Sfmolbmmdsrjpg IV / 328 kW / 446 HP / 6 cylinder / tank 700 L / speed rating: 2.100 rph / Drum TM-F 32 teeth / shredding comb 17 teeth / hydraulic adjustable cutting clearance 0-45 mm / length drum: 3.000 mm / external diameter: 1.050 mm / diameter pipe: 770 mm / 32 screwable teeth / discharge belt W = 1.000 mm / conveyor belt L= 6.500 m, W = 1.000 m / hydraulic oil tank 200 L / overband magnetic system / central lubrication / weight: ca. 27,50 t / throughput: approx. 25 – 80 t/h, depending on type of material / noise emission: 118 dB (A) /

Condition: good (used), Year of construction: 2022, operating hours: 5,933 h, Functionality: fully functional, machine/vehicle number: 449125, CAT® C18 / Motor Tier 4 Final, Stage V / 447 kW / 608 HP / magnetic separator / Bio cutting unit / Radio remote control / pre-driving device / Material: good for green waste, root stocks and all kind of residual and waste wood / central lubrication / weight ca. 26 t / basket screens: possible 80 mm round, 100 x 100, 125 x 125 mm or 250 x 250 mm square or size at customer´s option / 1.900 rph / drum length: 2.820 mm / drum speed: 1. gear 29 rpm, 2. gear: 44 rpm / transport position mm (LxWxH): 9.644 x 2.549 x 3.389 / sound power level: 114 dB (A) / Fe Ia Sfjlt Uvlsmrspg

Condition: new, Year of construction: 2023, operating hours: 720 h, low-speed universal waste shredder / Diesel engine CAT® C13 / Motor Tier 4 Final, Stage V / 323 kW / 446 PS / magnetic separator / suitable for all types of waste, wood and green waste / Radio remote control / pre-driving device / central lubrication / weight ca. 26 to / drum length: 3.000 mm / drum speed: max. 32 rpm / drum diameter: 770 mm / shredding unit: TM-XXF 22 / number of teeth: 22 / Counter-comb: number of teeth 23 / Hydraulically adjustable cutting gap 0-45 mm / noise emission: 120 dB (A) Fe Ia Sfelbmidsmrepg

Condition: good (used), Year of construction: 2020, operating hours: 4,104 h, Functionality: fully functional, machine/vehicle number: 447184, CAT® C13 / Motor Tier 4 Final, Stage V / magnetic separator / Bio cutting unit / Radio remote control / pre-driving device / Material: good for green waste, root stocks and all kind of residual and waste wood / central lubrication / weight ca. 25 to / basket screens: possible 80 mm round, 100 x 100, 125 x 125 mm or 250 x 250 mm square or size at customer´s option / 1.900 rph / drum length: 2.820 mm / drum speed: 1. gear 22 rpm, 2. gear: 34 rpm Fpe Ish Dz Tvsa Sfmrog