Vickers Hardness Tester

AFFRI WIKI 90

Year of construction: 2003, condition: ready for operation (used), A total of seven injection molding machines Arburg are available. 1) Arburg 320C 600-250, year of manufacture: 2001, operating hours: 83365h, clamping force: 600kN, screw diameter: 30mm, shot weight: 97g, max. injection pressure: 2470bar, injection volume: 106cm³, centering: 125mm/125mm, max. opening stroke: 550mm, plate distance: 550mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 320mm/320mm, core pulls: 2, temperature control units: 6, machine dimensions X/Y: approx. 4000mm/2300mm. Including Multilift handling unit. 2) Arburg 420C 1000-250, year of manufacture: 2001, operating hours: 90769h, clamping force: 1000kN, screw diameter: 30mm, shot weight: 97g, max. injection pressure: 2470bar, injection volume: 106cm³, centering: 125mm/125mm, max. opening stroke: 750mm, plate distance: 750mm, plate dimensions X/Y: 570mm/570mm, tie bar distance: 420mm/420mm, core pulls: 2, machine dimensions X/Y: approx. 4700mm/2350mm. Including Multilift handling unit. 3) Arburg 270C 300-100, year of manufacture: 1999, operating hours: 78784h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, injection volume: 31cm³, centering: 110mm/110mm, max. opening stroke: 550mm, plate distance: 550mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 270mm/270mm, core pulls: 1, temperature control units: 6. Including Geiger handling unit. 4) Arburg 320C 300-100, year of manufacture: 2000, operating hours: 78784h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, injection volume: 31cm³, centering: 125mm/110mm, max. opening stroke: 350mm, plate distance: 350mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 320mm/320mm, core pulls: 1, temperature control units: 6. 5) Arburg 220C 250-60, year of manufacture: 2001, operating hours: 86595h, clamping force: 250kN, screw diameter: 22mm, shot weight: 27g, max. injection pressure: 2340bar, injection volume: 30cm³, centering: 110mm/110mm, max. opening stroke: 425mm, plate distance: 425mm, plate dimensions X/Y: 400mm/400mm, tie bar distance: 221mm/221mm, core pulls: 1, temperature control units: 6. 6) Arburg 270C 300-100, year of manufacture: 2007, operating hours: 59885h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, injection volume: 31cm³, centering: 110mm/110mm, max. opening stroke: 550mm, plate distance: 550mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 270mm/270mm, core pulls: 2, temperature control units: 6, machine dimensions X/Y: approx. 3750mm/2400mm. Including Multilift handling unit. 7) Arburg 220S 250-60, year of manufacture: 2001, operating hours: 57504h, clamping force: 250kN, screw diameter: 18mm/22mm, shot weight: 18g/27g, max. injection pressure: 2500bar/2340bar, injection volume: 20cm³/30cm³, centering: 110mm/110mm, max. opening stroke: 425mm, plate distance: 425mm, plate dimensions X/Y: 400mm/400mm, tie bar distance: 221mm/221mm, core pulls: 1, temperature control units: 6, machine dimensions X/Y: approx. 3300mm/1100mm. Documentation available. An on-site inspection is possible. Prsdstyyn Hjpfx Ah Ujf

Year of construction: 2023, condition: new, - modern ergonomic design - manual test with analogue Measuring Clock (Reading accuracy 0.2 HR) - easy to use and quick test process - Height Capacity approx. 185mm - Hepth Capacity approx. 160mm - Dimensions 545x182x755mm Test loads: 60 / 100 / 150kg Test method: HRA/HRB/HRC Pedpfopbbc Hox Ah Usrf Standard delivery: - Hardness tester - V-Anvil - Flat Anvil Ø150mm - Flat Anvil Ø50mm - Ball Indenter 1/16" with ball - Diamond indenter 120° Rockwell - Spindle protection - Accessory case

Condition: excellent (used), Year of construction: 2010, Material Testing Machine: ZwickRoell GmbH mod.Z005 TN Designed to perform standard tests on materials and components, allowing for precise measurements of strength, flexibility, and other material properties, which are crucial in engineering and material research. With advanced technology and intuitive software, these machines offer efficient and safe operation. The device includes accessories for measuring material tensile strength, compression, and bending. Technical Specifications: • Year of production: 2010 • Maximum load (Fmax): 5 kN • Test dimensions: - Height (without accessories): 1070 mm - Stroke height: 1000 mm • Frame dimensions: - Height: 1340 ... 1345 mm - Width: 770 mm - Depth: 439 mm • Weight: approximately 110 kg • Power supply: 230 V, 1Ph/N/PE, power consumption about 800VA The machine allows for the testing of various materials and components, including: • Construction materials: concrete, steel, wood • Plastics: flexibility, tensile strength • Metals: strength, hardness, and fatigue testing • Mechanical components: compression, bending, and tensile tests • Samples in various forms: thin-layered, block-shaped, tubular Thanks to the system's flexibility, tests can be adapted to specific requirements. Pjdpfeuna Iuox Ah Ujrf TAG: Laboratory Equipment, Material Testing, EPS Styrofoam, Polystyrene Production, Mechanical Testing, Thermal Conductivity, Material Properties, Construction Materials, Quality Control, Engineering Research

Condition: as good as new (ex-display), Year of construction: 2023, operating hours: 31 h, 3D Coordinate CNC measuring device Profitech Innometrik Advanced in gantry design (demo unit at a special price) Open Cable Special features of the gantry design: Gantry design with a low center of gravity, wide bearing separation and optimum stiffness to mass ratio. The granite guideways ensure a uniform thermal, dimensional, torsional and geometric stability of the machine. 24 air bearings for smooth movement of the three axes. High dynamics for better performance, the machine can achieve high accelerations like comparable medium and large CMMs. Thermally compatible materials and components minimize the influence of ambient temperature fluctuations on measurement results, Air filter and regulator. Z-axis pneumatic counterweight system. Granit table with thread inserts of size M10. Passive vibration isolation pads Technical specifications Measurement paths: X: 500mm Y: 600mm Z: 400mm Max workpiece weight: 250kg Psdpfxedyah So Ah Usrf Weight of the machine: 850kg Dimensions over everything: 1290x1160x2350mm Accuracy according to DIN EN ISO 10360-2 or ISO 10360-4: Volumetric probing deviation: MPEP = 2.2μm Volumetric length measurement deviation: MPEE = 2.2+ L / 350 (μm) Environmental conditions: Room temperature standard: 18-22 ° C Operating temperature 10-35 ° C Air Supply: Minimum air pressure: 6bar Air consumption: 90NI / min Also configurable as a complete package with touch probe, software commissioning and training. (Annual maintenance & calibration can also be offered)

Condition: excellent (used), Working travels 600 x 560 x 510 mm Table size 900 x 560 mm Spindle taper SK40 Spindle speeds 20 -12'000 rpm Tool changer 30 Pos. Control SIEMENS 840D Coolant through spindle Podpfxevhahrj Ah Usrf Misc. accessories MARCELS MASCHINEN CH

Condition: like new (used), Year of construction: 2016, Cleaning system type W 60 C Machine body, internal pipe system, switch cabinet and washing basket in stainless steel Combination machine - turntable system with removable turning device and small parts basket - Basket diameter turntable wash basket 600 mm - Usable interior height 370 mm - Basket load rotary plate wash basket 100 kg - Usable interior height 530 mm - Dimensions of small parts basket 375 x 220 x 200 mm Mesh size 12 mm - Basket load small parts basket 20 kg Complete stainless steel design Pump(s) and external piping/fittings Prjdsq Ewgkepfx Ah Uef Version for operation with Liquids with a density of 1.3 due to reinforced pump with frequency converter Chip/particle filter with bath cover plate ECO flushing (loss of sink) for minimum water consumption Water supply from the operator's mains supply with hot water supply on the machine side Hot air drying 1 x 4 KW Oil skimmer Pumping device/floor flushing with pump and pipe system in stainless steel

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. Pjdpjhzbipefx Ah Ujrf - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: used, Year of construction: 2017, turning diameter max. 356 mm turning length 705 mm control M730 UM Mapps CELOS greates pass round over bed 920 mm Swing dia. over traverse guideway 742 mm turning speed range - main spindle 4.000 min/-1 power capacity - main spindel 18,5 / 15 kW spindle nose JIS A2-8 spindle bore 80 (91) mm C-Axis 0,001 ° Spindle speed range subspindle 6.000 min/-1 power capacity - Sub spindle 11 / 7,5 kW spindle bore 43 mm C-Axis 0,001 ° x-travel 260 mm z-travel 795 mm Y - Axis +/-50 mm rapid traverse ( X / Y / Z ) 30 / 10 / 30 m/min number of toolpositions 12 pos. Pjdpfx Ahjxzk Ifo Uorf Schank height for square tool 25 mm Drill shank diameter 50 mm turret change time 0,27 sec. Spindle speed - driven tools max. 10.000 min -1 power capacity - driven tools 5,5 / 4,2 kW total power requirement 41 kVA weight of the machine ca. 6,4 t dimensions of the machine ca. 4,0 x 3,0 x 2,3 m CNC - Turning- and MillingCenter DMG MORI - NLX 2500 SY / 700 - Subspindle - Tool-Drive - C, Y-Axis - only 1.237h Spindle hours

Condition: excellent (used), functionality: fully functional, Year of construction: 2021, operating hours: 22,351 h, control type: CNC control, degree of automation: semi-automatic, laser source manufacturer: Trumpf, laser hours: 17,317 h, laser power: 4,000 W, sheet thickness (max.): 20 mm, sheet thickness steel (max.): 20 mm, sheet thickness stainless steel (max.): 15 mm, sheet thickness aluminum (max.): 10 mm, working length: 3,000 mm, working width: 1,500 mm, travel distance Z-axis: 115 mm, repeat accuracy: 0.03 mm, type of cooling: water, overall weight: 12,000 kg, Equipment: CE marking, cooling unit, documentation/manual, dust extraction, emergency stop, safety light barrier, For sale: TRUMPF TruLaser 3030 with LoadMaster automation Machine installed in June 2021. Serviced exclusively by TRUMPF Slovakia, with professional maintenance performed regularly every six months. Machine in excellent condition, equipped with LoadMaster automation. Prjdswya Twopfx Ah Ujf Sheet metal cutting up to 25 mm thickness. Type and power of resonator: CO₂, 4 kW. Maximum working area: 3000 × 1500 mm. The machine will be in operation until the end of December 2025; inspection in full operation is possible at any time. Full service history documentation will be provided.

Year of construction: 2024, condition: new, machine/vehicle number: H3000-H5000TM, Universal testing machine H3000TM-H5000TM according to DIN EN ISO 7500 The universal testing machine of the H3000TM-H5000TM series is a single-spindle machine, a robust construction made of aluminum and V2a with ball screws, ball bushing guides and toothed belt drive. The bellows cover protects the spindle and guides. The testing machine is microprocessor controlled and has a membrane keypad. The 2-line LCD display shows the force and travel. The testing machine can be used as standalone or with a PC via USB interface. The displacement is measured by means of an encoder 0.01 mm visible resolution on LCD (internal 0.0001mm). The machine is manufactured with a standard load cell: 0.03% linearity and the corresponding calibration. Optionally it is possible to add a second channel for a second load cell or a displacement transducer. The universal testing machine is manufactured with two different travels, 500mm or 1200mm (without load cell and testing tool). Prsdpjiq Hxkjfx Ah Uof Further scope of delivery: One load cell up to nominal load, 220 Volt cable, USB cable, description, CE declaration of conformity. For more information, please refer to the attached description. Load cell 3000N-5000N Measuring range: 5-5000N tension and compression, with nom. 2mV/V output signal, overload protection: +/- 1000%, linearity: +/- 0.05%, hysteresis: +/- 0.03%, repeatability: +/- 0.02%, with, incl. 1.5m connection cable incl. calibration certificate Long travel extensometer HE 900mm measuring travel, measuring arms motorized, including electronics Accuracy class class 1 from 1mm travel according to DIN EN ISO 9513 Measuring principle optical incremental Measuring path 900 mm , minus measuring length Display error 6 µm or 2 Resolution 1 µm Actuating force 10 cN Standard initial device measuring length (Lo) 10-100 mm, in 5 mm steps Lo adjustment is manual Measuring arm opening and closing is motorized specimen diameter 0-30 mm specimen thickness 0-30 mm sample width 0-100 mm Weight approx. 32kg Scope of delivery strain gauge complete with electronics Cutting edges round: 1 set each carbide / rubber wear parts measuring blades optional rectangular cutting edges ATTENTION: When using optional cutting edges a readjustment of the lo a readjustment of the lo stop is necessary.