Wire EDM machine

AGIE Challenge 3

Year of construction: 2008, condition: refurbished (used), AGIECUT Challenge V3, Year of manufacture 2008 travels: X= 500 mm, Y= 350 mm, Z= 256 mm travels U/V-axis: +/- 70 mm Maximum taper: 30° at 100 mm height Maximum workpiece dimensions: 1050 x 650 x 250 mm Maximum workpiece weight: 400/800 kg Rsdpfx Ahjm Amf De Uel Achievable surface quality: Ra: 0.2 µm Available wire diameters: 0.10 - 0.33 mm Water bath machine with automatic wire threading With automatically lowerable tank (accessible from 2 sides) Incl. AGIEJOGGER- hand box for comfortable set-up Incl. AGIESETUP 3D AGIEVISION 5 control system AGIE IPG-V generator Dimensions (length x width x height): 2800 x 2400 x 2220 mm Net weight: 4500 kg The machine is cleaned, overhauled and extensively tested by us after receipt of order. Incl. user training at Techma on your overhauled machine Optional: transport, commissioning, training, cooler

Condition: good (used), Year of construction: 2004, TBT ML 200-2-800 deep hole drilling machine TECHNICAL DATA Type: ML 200-2-800 Year of construction: 2004 Control: Simatic OP17 Number of spindles: 2 Spindle distance: 12 mm Drilling slide stroke: 800 mm Drilling range: 1 - 10 mm Process: Single-lip drill Drilling depth: Immersion spindle: 110 mm Rsdpfevcbg Sex Ah Usl Seal housing: 430 mm Sealing housing with steady rest: 400 mm Spindle drive: Power: 1.7 / 2.9 / 1.3 Voltage: 240 / 350 / 350 V Frequency: 100 - 800 Hz Weight: Approx. 2.6 T We assume no liability for the accuracy, completeness and up-to-dateness of the information provided

Year of construction: 2006, condition: refurbished (used), AGIECUT Challenge 3 eCut Year of construction 2006 Travels: X= 500 mm, Y= 350 mm, Z= 256 mm Travels U/V axis: +/- 70 mm Maximum taper: 30° at 100 mm height Maximum workpiece dimensions: 1050 x 650 x 250 mm Rjdpfxogfm Rrs Ah Uel Maximum workpiece weight: 400/800 kg Achievable surface quality: Ra: 0.2 µm Available wire diameters: 0.10 - 0.33 mm Water bath machine with automatic wire threading With automatically lowerable container (accessible from 2 sides) Incl. AGIEJOGGER hand box for convenient set-up Incl. AGIESETUP 3D AGIEVISION control unit AGIE generator with eCut technologies for faster and more efficient processing Dimensions (length x width x height): 2800 x 2400 x 2220 mm Net weight: 4500 kg The machine is cleaned, overhauled and thoroughly tested by us after receipt of the order. We then put the machine into operation on your premises. You receive a 6-month warranty on the machine. We are happy to offer you the following additional services: - Control and maintenance training - Cooling unit - Programming system - Consumables - Clamping devices - Transportation

Year of construction: 2003, condition: ready for operation (used), A total of seven injection molding machines Arburg are available. 1) Arburg 320C 600-250, year of manufacture: 2001, operating hours: 83365h, clamping force: 600kN, screw diameter: 30mm, shot weight: 97g, max. injection pressure: 2470bar, injection volume: 106cm³, centering: 125mm/125mm, max. opening stroke: 550mm, plate distance: 550mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 320mm/320mm, core pulls: 2, temperature control units: 6, machine dimensions X/Y: approx. 4000mm/2300mm. Including Multilift handling unit. 2) Arburg 420C 1000-250, year of manufacture: 2001, operating hours: 90769h, clamping force: 1000kN, screw diameter: 30mm, shot weight: 97g, max. injection pressure: 2470bar, injection volume: 106cm³, centering: 125mm/125mm, max. opening stroke: 750mm, plate distance: 750mm, plate dimensions X/Y: 570mm/570mm, tie bar distance: 420mm/420mm, core pulls: 2, machine dimensions X/Y: approx. 4700mm/2350mm. Including Multilift handling unit. 3) Arburg 270C 300-100, year of manufacture: 1999, operating hours: 78784h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, injection volume: 31cm³, centering: 110mm/110mm, max. opening stroke: 550mm, plate distance: 550mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 270mm/270mm, core pulls: 1, temperature control units: 6. Including Geiger handling unit. 4) Arburg 320C 300-100, year of manufacture: 2000, operating hours: 78784h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, injection volume: 31cm³, centering: 125mm/110mm, max. opening stroke: 350mm, plate distance: 350mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 320mm/320mm, core pulls: 1, temperature control units: 6. 5) Arburg 220C 250-60, year of manufacture: 2001, operating hours: 86595h, clamping force: 250kN, screw diameter: 22mm, shot weight: 27g, max. injection pressure: 2340bar, injection volume: 30cm³, centering: 110mm/110mm, max. opening stroke: 425mm, plate distance: 425mm, plate dimensions X/Y: 400mm/400mm, tie bar distance: 221mm/221mm, core pulls: 1, temperature control units: 6. 6) Arburg 270C 300-100, year of manufacture: 2007, operating hours: 59885h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, injection volume: 31cm³, centering: 110mm/110mm, max. opening stroke: 550mm, plate distance: 550mm, plate dimensions X/Y: 446mm/446mm, tie bar distance: 270mm/270mm, core pulls: 2, temperature control units: 6, machine dimensions X/Y: approx. 3750mm/2400mm. Including Multilift handling unit. 7) Arburg 220S 250-60, year of manufacture: 2001, operating hours: 57504h, clamping force: 250kN, screw diameter: 18mm/22mm, shot weight: 18g/27g, max. injection pressure: 2500bar/2340bar, injection volume: 20cm³/30cm³, centering: 110mm/110mm, max. opening stroke: 425mm, plate distance: 425mm, plate dimensions X/Y: 400mm/400mm, tie bar distance: 221mm/221mm, core pulls: 1, temperature control units: 6, machine dimensions X/Y: approx. 3300mm/1100mm. Documentation available. An on-site inspection is possible. Redpfotyyn Hsx Ah Uel

Condition: excellent (used), Brand: KENT Model: KGS-250AHD Type : Tangential Work surface 460x200 mm Longitudinal course 540 mm Rsdpfx Ahsh Ha Ips Uel Cross course 260 mm Distance form center to table 490 mm Max. Weight on the table including magnetic chuck 103 for series 250 kg 150 for series 818 kg Slote in T 14x 1 mm/N Longitudinal table speed 5- 23 m/min Crank cords feed 1 gra 0,02 mm - 1 rev 4 mm Automatic traerse feed per pass 0.1 -5.5 mm Automatic advance 50 Hz- 820 mm /min. - 60Hz 980 mm/min Wheel size 180 x 13 x 31. 75 mm Spindle speed 50 Hz 2850 rpm - 60 Hz 3480 rpm Upright crank 1 gra 0,01 mm - 1 rev 2 mm Automatic feed increment 0,002- 0,02 mm Spindle motor 2 x 2 HP X P Hoist motor NA kg x cm Hydraulic motor pump 1 X 6 HP X P Drain motor 1/8 X 2 HP X P Transverse agace engine 1/5 x 6 HP X P Machine height 1775 mm Machine dimension 3260 x 2460 mm Net weight 1300 kg Gross weight 1500 K

Condition: used, Year of construction: 1992, closing pressure 600 kN clamping plate 460x460 mm distance between columns 300x300 mm weight of the machine ca. 4,5 t lock stroke 230 mm capacity of ejector 40 kN ejector stroke 70 mm height of form 120-350 mm column diameter 56 mm casting capacity 55 kN casting plunger stroke 130 m/m Redpfx Ahefrvzvo Ujl injection plunger diameter 45,50,55 mm casting volume (DIN 24480) 76,121,165 cm 2 volume cast pressure 345,280,231 kp/cm² casting area 174,214,260 cm 2 Traverse Stroke 150 m/m Used Die Casting machine DAW 50 with SBC 2 control for the use of zinc alloys. Available from used machine stock. The machine is equipped with an electric furnace from Rauch Typ MO50E and used pneumatic sprayer 401. Recommendation from the manufacturer is some repair / general overhaul in the overhaul plant. It can be carried out in the scope of agreement.

Condition: good (used), Year of construction: 2021, MAZAK Integrex i-250H ST SmoothAi, year of manufacture 2021, HALTER loading portal with robot, bar feeder BREUNING-IRCO ILS-MUK, main spindle 8" sub spindle 8", machining diameter 670 mm Bar diameter 65 mm Spindle speed: Turning: 5,000 rpm Rjdpfx Asxy T Dtjh Ujl Milling: 12,000 rpm Chain magazine: 38 positions, Turret: 12 positions

Condition: good (used), Year of construction: 2003, functionality: fully functional, travel distance X-axis: 1,200 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 500 mm, controller model: iTNC 530, rotational speed (max.): 18,000 rpm, overall weight: 12,500 kg, General Data Measurements width 3970 mm Measurements depth 4629 mm Dqmcjh Measurements height 3050 mm Machine weight 12700 kg Rsdpfxsvambio Ah Ujl Main Drive Number of spindles 1 Spindle speed range 16000 rpm Spindle motor power 10 kW Tool taper SK 40 Number of axis 3 Movement X-Axis Movement 1200 mm Y-Axis Movement 900 mm Z-Axis Movement 500 mm Unfpvoddib Table Outer length 1400 mm Outer width 900 mm This 3-axis HERMLE C 1200 V vertical machining centre was manufactured in 2003. It features a robust clamping table measuring 1400 x 900 mm and a high-performance milling spindle with a maximum power of 10 kW, torque up to 87 Nm, and speeds up to 16,000 RPM. Ideal for complex machining tasks, the HERMLE C 1200 V machine we have for sale offers precision and durability. Tool magazine can be dismantled so the width can be reduced to 2500 mm. Contact us for more information. Application Types Milling

Condition: excellent (used), Control : D.Electron Z 32 centre height 220 mm Centre distance 1000 mm turning Ø over bed 440 mm turning diameter over slide 245 mm Travel -Z axis 750 mm width of lathe bed 320 mm spindle mounting CL 6" spindle bore 62 mm spindle speeds 0 - 2000 rpm Rjdpfx Ahed Sitkj Usl rapid traverse X/Z 7 m/min quill travel by hand 200 mm quill diameter 80 mm quill mounting MK 4

Condition: used, Year of construction: 2000, greates pass round over bed 520 mm swing diameter over bed slide 480 mm turning length 3000 mm control 840 D SIEMENS number of tools 12 Driven tools - quantity 6 spindle bore 103 mm c-axis ja 0 Scope of delivery of the basic machine: SINUMERIK 840 D 3 controlled axes Rotation Ø over bed 520 mm Turning Ø over bed slide 480 mm Tool carrier with 12 cylindrical shank holders Ø 50 mm 1-stage AC main drive, 53 kW, 50 % ED Speed range 30 - 3000 min-¹ Main spindle head size 8 Clamping door for clamping devices chip conveyor THREE-DIMENSION 3000 mm 12 cylindrical shank holders DIN 69880-50x78 of which 6 positions can be equipped with driven tools, Power 6 kW at 60 % ED, Rjdpfx Ahowp S Sqo Uol speed range 20-2500 min-¹ 2 gear stages C-AXLE Speed range 0-20 min-¹ Max. Angle specification 9999.999° Working range according to work area diagram POWER CHUCK 3 NHF 315-82 A8 FABR. FORKARDT with centrifugal force compensation, Outer Ø 315 mm, bore Ø 82 mm, with hard top jaws, ground, rod material Ø max. 63 mm including draw tube and attachment