Eccentric press

BBT Pressen E 15

Condition: good (used), Year of construction: 2018, Manufacturer: INDUCTAFLEX Type: AL-3e Control system: ACCURATE touch screen Year of construction: 2018 3 rolls driven servo Torq each roller 3500 nM Electrically support rolls Intelligent software : Ellipse program U Bend shapes control of tangents Auto section detector Specifications Metric US Standard Horizontal and Vertical Horizontal Axis Ø 105 mm Number of rollers 3 Stroke X axis Gsdpfovd Dftox Abdett 0 - 400 mm Dimensions (estimate) length 4500 mm width 3200 mm height 2700 mm weight 3300 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Gedpfx Ajg U Utvebdett Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: used, Roller sets for section bending machine, 3-roll ring bending machine HERKULES WETZLAR The rollers fit a section bending machine HERKULES WETZLAR type BO 238 N Shaft diameter: 60 mm with 18 mm keyway 2 rollers set No. 1, roller diameter = 110 mm, roller width = 180 mm 2 rollers set No. 2, roller diameter = 160 mm, roller width = 40 mm 3 rollers set No. 3, roller diameter = 150 mm, for tube diameter Ø 33 mm, roller width 87 / 115 mm - Roller set No. 3 with adapter ring from Ø 93 to Ø 60 mm without keyway The machine had 2 driven rollers Total weight of all rollers: 57 kg Godpfoglaq Isx Abdett Good condition

Condition: new, Year of construction: 2024, load capacity: 300 kg, Welding turntable KT 300 Horizontal load 300 KG, tilted 150 KG Power consumption 220V, 50 Hz Table diameter 450mm Height 500mm Infinitely variable tilt range via crank gear motor 0 - 90° Speed 0.3 to 2.5 rpm Incl. foot remote control Surcharge: Quick-release jaw chuck Diameter 300mm, 450.-€ Gsdpsc Ug Tljfx Abdjtt

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Gedpfjuz If Njx Abdott Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, 3-roller bender Gtjdsuluhwepfx Abdet Brand RAGACHE Type New Tube CP70 3 drive rollers diameter 232 mm Rectangle capacity Standard steel 60.0 mm Round capacity Standard steel 40.0 mm Capacity L Standard steel 70.0 mm Capacity U Standard steel 120.0 mm Capacity T Standard steel 60.0 mm Capacity I Standard steel 120.0 mm

Condition: used, mileage: 209,000 km, power: 96 kW (130.52 HP), first registration: 10/2013, fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, emission class: euro5, number of seats: 3, loading space length: 4,200 mm, loading space width: 2,050 mm, loading space height: 2,050 mm, Equipment: ABS, central locking, * Aluminum platform Godpfx Abehqzg Hsdstt * fastening eyes * ster * gel * ABS * ASR * Central locking * 6-speed * Power steering * Driver's airbag * Steering wheel adjustment * CD radio * Payload 1400kg * Ladder grille * WhatsApp/Tel.

Year of construction: 1980, condition: good (used), machine/vehicle number: 3253-80, Offer 22045 Technical data approx: Godpsktg Dhofx Abdjtt - Compressive force 10 t - throat 150 mm - Table size . 520 x 320 mm - Table height adjustable 160 mm - drop-through hole in table 165 x 125 mm - gr. installation height 220 mm - ram surface 240 x 150 mm - mortise in ram 30 mm - ram adjustability 40 mm - stroke adjustment 4 - 60 mm - stroke rate 130 1/min - hydr. actuated clutch - Two-hand operation - E. foot switch - separate switch cabinet - drive 380 V / 1,1 kW - space requirement approx. W 1000 x H 1800 x D 1100 mm - weight approx. 1300 kg

Year of construction: 2008, condition: excellent (used), Max. bar diameter 65 mm Max. bar length 3000 mm Gedpfjin Hkmjx Abdjtt

Condition: used, Year of construction: 1959, pressure 063 t throat 280 mm stroke 8 - 100 mm no. of strokes 65 /min distance table/ram, max. stroke up, adjustment up 550 mm table surface area 630 x 500 mm hole in the table 230 mm table height over floor 740 mm table adjustable 200 mm ram surface 320 x 260 mm ram adjustment 63 mm power capacity 5,5 kW Gtedpsvuk Rwofx Abdet weight 4,6 t Dimensions (WxDxH) 1,4 x 1,8 x 2,4 m permitted for manual loading according to the German Safety Regulations (UVV) with motor, friction clutch, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, adjustable table, manual centralized lubrication, two-hand operation Press is currently under revision