Edgebander

BIESSE AKRON 1400

Condition: used, Year of construction: 2015, functionality: fully functional, BIESSE Edge Banding Machine AKRON 1440-A Automatic single-sided edge banding machines for gluing and processing straight edges with roll material (melamine, PVC, ABS, veneer) and strip material (solid wood, laminate, sliced veneer, etc.) • NC control with touch display • Automatic start of aggregate motors • Direct selection for second pass • Operating data acquisition • Software-guided maintenance TECHNICAL DATA Workpiece thickness 10-60 mm Workpiece thickness with MFU aggregate (depending on profile) 10-35/60 mm Edge height 14-64 mm Edge thickness – roll material 0.4-3 mm Edge thickness – strip material (*) 0.4-10 (12) mm Workpiece overhang 25 mm Minimum panel length 140 mm Minimum width (at 140 mm length) 85 mm Minimum width (at 250 mm length) 50 mm Feed speed 12 m/min Dust extraction* 8x connection Ø100 mm Compressed air connection 7 bar Glue pot capacity 2 (approx.) kg * Depending on selected aggregates. - GLUING UNIT VC-511 Applies the hot-melt adhesive to the workpiece, feeds the edge to the workpiece, automatically cuts it from the roll, and presses it onto the workpiece, guaranteeing perfect positioning. - END TRIMMING UNIT IN-801 For trimming the front and rear edge overhangs with 0° to 15° angle. - 2-MOTOR MULTIFUNCTIONAL PROFILE MILLING UNIT AR02 E For corner rounding and profile milling of workpiece edges made of synthetic material up to a thickness of max. 3 mm. JOINTING CUTTER UNIT RT02 Joins the workpiece before glue application. Equipped with two 1.8 kW high-frequency motors at 12,000 rpm. SCRAPER UNIT RB02 For post-processing thick PVC/ABS edges. FLAT SCRAPER RC02 Aggregate for removing excess glue in the edge-to-panel area. Equipped with tracing rollers and a flat knife with engagement control. BUFFING UNIT SZ02 For cleaning and buffing the workpiece edge using fabric polishing discs. The unit automatically adapts to the workpiece thickness. ANTI-ADHESIVE SPRAY UNIT ADZ02 Precision application of anti-adhesive using injectors activated by numerical control. KIT PRO-GLUE The PRO-GLUE kit includes the following components: • TEKNO-GLUE system for optimal gluing through: - controlled pressure of the glue roller - automatic disengagement in case of feed stop - automatic ON/OFF of the glue unit • REVERSE system to switch the glue roller for co- or counter-rotation Electrical and mechanical preparation for the use of special glue pots for POLYURETHANE glue with machines equipped for EVA gluing. Bodpfx Asxzb Iisl Ijdb NC Axis for Fine Trimming Unit Kit for the automatic adjustment of tracing rollers and tools to match edge type and thickness. Adjustment takes place via the control system. Pair of multiprofile cutters for the fine trimming unit: 25-degree bevel, radius 2 mm + radius 1 mm plus straight profile for solid wood. NC Axis for Profile Milling Unit Kit for automatic adjustment of the tracer to match the edge thickness. Adjustment takes place via the control system. Function for processing only on the corners. NC Axis for Scraper Unit Kit for automatic adjustment of tracing rollers and tools to match edge type and thickness. Adjustment takes place via the control system.

Condition: like new (used), Year of construction: 2023, SCM Accord 40 fx CNC machining center with the following equipment: Working area X-Y = 6360 x 1905 mm, Z = 350 mm OF0158 Usable Z clearance height = 350 mm with H50 suction cups OF0165 Axis travel speed of Accord 40 fx Version PRO-SPEED OF0168 Pendulum (dual-zone) operation OF0169 Automatic axis lubrication OF0299 TELESOLVE remote maintenance via Internet 450328 eye-M PRO control console with integrated PC 450291 Additional fixed control panel 870068 TECPAD – remote control of machine functions 560058 No. 10 carrier rails MATIC – L1825 230429 MAXI working unit – Prisma KT 1 870046 Prepared for angle gearbox "Prisma KT-KS" 470014 Air nozzle for tool 870119 Device for tool length measurement 870120 Device for panel thickness measurement 870009 Drilling unit F16 OF0176 Front stop row H50 for worktable with 10 carrier rails 510205 Preparation for clamps for worktable with 10 carrier rails 480178 Front stop row H110 for worktable with 10 carrier rails 480105 Rear stop row H110 for worktable with 10 carrier rails 480137 First lateral stop row H110 for worktable with 10 carrier rails 480005 Suction cups H110, 145x145 mm, 36 pcs 480006 Suction cups H110, 145x55 mm, rotatable, 10 pcs 480007 Suction cups H110, 180x65 mm, rotatable, 10 pcs 480018 Suction cups H110, 145x30 mm, rotatable, 5 pcs 480410 Lifting devices H110, 8 pcs 350016 Vacuum pump 250 (300) m³/h 560538 Additional automatically adjustable base for MATIC 10 carrier rail 190046 PRO-SPEED safety system 524800 "SAV€NERGY" 2.0 energy saving system 210837 TR12 – lateral tool magazine 210056 Rapid 24 – rear tool magazine OF0182 Air conditioning for control cabinet Bodpfsyfgzdsx Al Ijdb OF0438 Human-machine interface software (HMI) MAESTRO ACTIVE OF0543 Operating system Windows 10 embedded 64 bit OF0422 Machine operating interface software Maestro cnc OF0435 Hardware dongle for Maestro cnc 524309 Maestro 3D-Advanced module 109993 MACHINE LANGUAGE: German SPECIAL FEATURES INCLUDED IN MACHINE CONFIGURATION: - Extension of maximum panel width to 2,120 mm for full processing; traverse length remains unchanged at 1900 mm. - 10 support suction cups for remnants MACHINE ALREADY DISMANTLED AND STORED. LIST PRICE 2023 EUR 399,890.--

Condition: refurbished (used), Year of construction: 2024, Manufacturer: Elumatec Type SA/ SAS 142 Overhaul year: 2024 Saw blade max. carbide: 500 mm Drive power saw motor: 4 KW Saw motor speed: 2800 min-1 Cutting speed saw blade 500 mm: 4400 m/min Saw height control: infinitely variable, fully electronic Working range square 90° max.: 130 x 130 mm Working range flat: 90° max.: 190 x 130 mm Working range round: 90° max.:150 mm Pneumatic feed length: 5-560, 10-1120 mm Compressed air connection, on site 6 bar Weight(saw)approx.: 800 kg Dimensions LxWxH (saw)approx.:2900mm x 1400mm x 1500mm Installation area LxW: 2900mm x 1400mm Additional description Elumatec SA/ SAS 142 4KW Retrofit Elumatec SA 142 4KW Retrofit Fully automatic sawing machine for non-ferrous metal and plastic After completion of the retrofit, the machine is in mint condition, both technically and visually. The machine will be overhauled in our company at the customer's request. Among other things, the following points were renewed: - Conversion to Siemens S7 PLC control - Conversion to Siemens HMI control panel - New electrical components - New pneumatic lines - Maintenance or replacement of all pneumatic cylinders and valve terminals Bedpfx Alsuiy Nye Isdb - Maintenance of minimum lubrication system - Replacement of general wear parts - Overhaul of the cab Warranty: Unless otherwise agreed, we provide a 6-month warranty on all parts overhauled or replaced by us. Working time and wearing parts are excluded from the warranty. Optional: - Extension of the sawing area to flat 90° max.: 300 x 120 mm - Splitting extension (for a high-quality cut surface without return marks) - Servo-controlled material feed - Saw blade feed Servo-controlled - Mass clamping device Feed vice - Delivery and installation on your premises - Training of your employees

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, operating hours: 5,383 h, The HOMAG DRILLTEQ V-200 is a compact and highly efficient CNC vertical machining center designed for precise drilling, grooving and routing operations in furniture and cabinet production. Thanks to vertical processing, the machine requires minimal floor space while offering high flexibility and productivity. It is ideal for batch size 1 production as well as serial manufacturing. Bdedpfx Aeym Ny Sjl Ieb The machine is in very good technical condition and can be inspected under power.

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Bedpfx Aoxy Tmnjl Iedb

Condition: used, Year of construction: 2014, total height: 2,400 mm, total length: 4,500 mm, total width: 2,200 mm, Empty weight: 2.500 kg CNC Machining Center Biesse skill 12 24 G FT Year of construction 2014 Machine no. 60961 Recording HSK F63 10x vertical drilling 12 switch positions Bdjdpewnhanjfx Al Isb Software: BiesseWorks X axis 2465 mm Y-axis 1260 mm Z axis 324 mm Disassembled for transport on normal trailer; 4500x2200x2400mm; Own weight 2000kg - Details: - └ Description: Pallet with white control box does not belong to this machine - Year: 2014 - Documentation available: Yes - CE certificate present: No - Serial number: 60961 - Number of milling spindles [pcs.]: 1 - Type milling table: Flat table - Tool clamping system: HSK-F63 - Drilling unit present: Yes - └ Vertical drilling spindles [pcs.]: 10 - Tool changer positions [pcs.]: 12 - System/software: BiesseWorks - Safety feature: Enclosed fence - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - Working range X [mm]: 2465 - Working range Y [mm]: 1260 - Z-axis working range [mm]: 324 - Transport dimensions: 4500mm x 2200mm x 2400mm (l x w x h) - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Painting system consisting of: Pos.1 Venjakob belt conveyor - Manufacturer: Venjakob - Working width: 1,300 mm - Length: 3,000 mm - Feed adjustable via handwheel ~ 2.5 – 7.5 m/min - Volt, Hz: 400 / 50 - Colour RAL 7035 Pos.2 Cefla dust extraction machine - Manufacturer: Sorbini - Type: VS/32-E - Year of manufacture: 1998 - Working width: 1,300 mm Bjdpfx Ajv I Akvsl Ijdb - Working height: 900 mm + - 20 mm - Operating side: right - Roller conveyor - Air blowing channel, above 2 pcs. - Air blowing channel, below 1 pc. - Dust remover brush - With ionisation bar from above - With ionisation bar from below - With own drive - With own control - Length ~ 910 mm - Width ~ 2,600 mm - Weight 1,260 kg - Extraction nozzle D 180 + 120 mm - Total connection 7.6 kW - Volt, Hz 400/ 50 Pos.3 Venjakob VEN SRAY Perfect automatic spraying machine - Manufacturer Venjakob - Type. VEN SPRAY PERFECT - Year of construction 2013 - Working width 1,300 mm - Working height 940 + - 20 mm - Operating side left - IR preheating, number of radiators 2 pcs. - Duo-design spray gun drive - Dry suction - Diameter of suction nozzle 600 mm - Exhaust air capacity 10,000 m³/h - Belt transport system - feed speed infinitely variable ~ 4-10 m/min - conveyor belt cleaning system - paint recovery via V-belt system - gun control, EPS-CNC CNC 7000 - colour management system for number of pumps 3+1 pcs. - number of installed airless spray guns 4 pcs. - Quick-change system for spray guns - Remote maintenance system - Dust cover on the outlet side of the machine - Exhaust air recirculation system - Exhaust air control of the suction ventilator - Machine suitable for water-based paints - Machine suitable for solvent-based paints - Length 5,509 mm - Width 4,500 mm + 2,400 mm - Height 3,380 mm + 510 mm - Total connection ~ 20 - 26 kW - Volt, Hz 400/50 - Colour RAL 7035 - Kremlin AVX AirMix spray guns - Small parts container - gun support arm system for quick removal of 4 AirMix spray guns from the spray booth, including quick couplings for pneumatics and material hoses. Pos.4 Venjakob belt conveyor - manufactured by Venjakob - working width 1,300 mm - length 2,000 mm - feed adjustable via handwheel ~ 2.5 – 7.5 m/min - Volt, Hz 400 / 50 - Colour RAL 7035 Pos.5 Cefla pallet dryer - Manufacturer Cefla - Type VN 2000/5500/190.5/30 - Year of construction 2003 - Working width 1,300 mm - Number of pallets 30 pcs. - Pallet length 5,600 mm - Usable pallet length 5,300 mm - Load capacity per pallet 300 kg - Max. part height ~ 110 mm - Clearance between pallets 120 mm - Dimension: centre of pallet to centre of pallet 3,658 mm - Max. part length ~ 5,200 mm - Number of controllable temperature zones 2 pcs. - Supply air flow rate 6,000 m³/h - Exhaust air flow rate 6,000 m³/h - Heat output max. 175 kW - Max. drying temperature ~ 55 - 60 degrees - With heat exchanger, hot water - Without hot water control valves - U-shaped flow direction - Inlet side on the right - Feed speed via frequency converter control ~ 2-20 m/min - Suitable for water-based paints - Suitable for solvent-based paints - Length 7,820 mm mm - Width 6,130 mm - Height 3,905 mm - Total connection ~ 23 kW - Volt, Hz 400 / 50 - Voltage fluctuations max. +/- 5 % - Without control valves and water pumps Pos.6 Cefla belt conveyor - Manufacturer Cefla - working width 1.300 mm - length 2.000 mm - feed adjustable via handwheel ~ 2.5 – 7.5 m/min - volts, Hz 400 / 50 - colour RAL 7035

Condition: good (used), Year of construction: 2016, functionality: fully functional, Used edge banding machine SCM - Model: Olimpic K360 T-ER1 - Very good condition. Bdedpfoyrr Nasx Al Iob - Immediately available - Video on request - Year of manufacture: 2016 - High-end configuration (2 extra glue pots)

Condition: used, Year of construction: 1996, Edge thickness: 0.4 - 12 mm Roll edge: 3 x 45 mm or 0.8 - 60 mm Minimum workpiece width: 65 mm Minimum workpiece length: 160 mm Workpiece thickness: 10 - 55 mm Feed rate: 13 m/min Pre-milling (joining) Glue pot Quickmelt Gluing unit Trimming Flush trimming Chamfering Radius trimming Corner rounding Flat scraper Buffing unit Machine dimensions: 7450 x 1220 x 2400 mm Weight: 3000 kg Bdedpfxevvkd Ts Al Iob Storage location: Nattheim

Condition: like new (used), Year of construction: 2011, machine/vehicle number: 0-261-04-5736, functionality: fully functional, operating hours: 806 h, workpiece height (max.): 60 mm, edge thickness (max.): 8 mm, feed rate X-axis: 11 m/min, total length: 5,700 mm, Equipment: documentation/manual, Brandt AMBITION 1440 KDF Year of manufacture: 2011 Year of commissioning: 2013 Bdedpfxsylvpqj Al Ieb In very good condition