Plate Bending Machine - 3 Rolls

BRONX

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Dsdpfoh U Rzgjx Ac Nocg Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: good (used), Year of construction: 2015, travel distance X-axis: 650 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 650 mm, 1 Horizontal machining center Make: STARRAG HECKERT, type: HEC 400D, year 2015, Control system, Siemens, type Sinumerik 840D, travel X/Y/Z = 650 x 650 x 650 mm, 2-fold pallet changer, pallet size 400 x 400 mm, NC rotary table 360x 0.001°, 80-fold tool changer, HSK 63 tool holder, spindle speed 15,000 rpm, IKZ 50 Dodpsuav H Nsfx Ac Njcg bar, belt filter, coolant temperature control, spindle cooling, chip conveyor, sound and control cabinets, operating hours 43,698, spindle hours 5,401

Year of construction: 2000, condition: excellent (used), maker: diverse (Europäische Union) year: 2000 tube Ø: 40 – 150 mm wall thickness: 1 – 4 (5) mm reference material (tensile strength): 1.000 N/mm² tube length shop entry: 4 – 10 m tube length shop exit: 4 – 8 m bundle weight: max. 3.000 kg bundle Ø: max. 600 mm working direction: left → right Dcjdpfx Ajmqkt Toc Neg The shop consists of: • tube bundle destacker I with separation MAIR • tube straightender (10 rolls) BRONX type 10Cr.6-BWS • tube bundle destacker II with separation MAIR • wet separator HANDTE • tube bundle destacker III with separation MAIR • tube testing eddy current/ultrasonic ATM/KRAUTKRÄMER/FÖRSTER • multiple-head saw MAIR type MC150/7/10 • tube bevelling machine MAIR • brushing machine MAIR • destacker/stacker MAIR • tube bundle destacker MAIR • tube banding machine MAIR/ORGAPACK • emulsion treatment SCHOENAUER • control Siemens S7 • hydraulics

Year of construction: 2000, condition: excellent (used), maker: diverse (Europäische Union) year: 2000 tube Ø: 40 – 150 mm wall thickness: 1 – 4 (5) mm reference material (tensile strength): 1.000 N/mm² tube length shop entry: 4 – 10 m tube length shop exit: 4 – 8 m bundle weight: max. 3.000 kg bundle Ø: max. 600 mm working direction: left → right The shop consists of: • tube bundle destacker I with separation MAIR • tube straightender (10 rolls) BRONX type 10Cr.6-BWS • tube bundle destacker II with separation MAIR Dedpfx Asmqkubjc Necg • wet separator HANDTE • tube bundle destacker III with separation MAIR • tube testing eddy current/ultrasonic ATM/KRAUTKRÄMER/FÖRSTER • multiple-head saw MAIR type MC150/7/10 • tube bevelling machine MAIR • brushing machine MAIR • destacker/stacker MAIR • tube bundle destacker MAIR • tube banding machine MAIR/ORGAPACK • emulsion treatment SCHOENAUER • control Siemens S7 • hydraulics

Condition: used, Year of construction: 2006, Technical details: x-travel: 800 mm y-travel: 800 mm z-travel: 800 mm turning speeds: 12.000 1/min tool taper: SK 50 control: SIEMENS 840D shopmill tool change unit: 240 fach size of pallet: 630 x 630mm mm spindle: 52 kW / 430Nm total power requirement: 87 kVA weight of the machine ca.: 15 t horizontal machining center, NC-round-table pallet-changer (2 pallets), Internal Coolant Supply 40 bar, prepared for Infrared Touch Probe Renishaw MP 10 without probe, tool-breakage control (mech.), MQL, airblast through spindle, oilmist suction, Dcjdpfx Aspumdcoc Nog TRANSMIT funbction, accuracy package, mode 4, glass window right door, incl. FASTEMS FPC 1000 pallet pool for 14 pallets, incl. setting up station, control, and 10 pallets approx. 98.500 h main switch on apprax. 45.500 Spindle hours *

Year of construction: 2000, condition: excellent (used), maker: diverse (Europäische Union) year: 2000 tube Ø: 40 – 150 mm wall thickness: 1 – 4 (5) mm reference material (tensile strength): 1.000 N/mm² tube length shop entry: 4 – 10 m tube length shop exit: 4 – 8 m bundle weight: max. 3.000 kg bundle Ø: max. 600 mm working direction: left → right The shop consists of: • tube bundle destacker I with separation MAIR • tube straightender (10 rolls) BRONX type 10Cr.6-BWS • tube bundle destacker II with separation MAIR • wet separator HANDTE • tube bundle destacker III with separation MAIR Dcjdpfxemqkuuj Ac Nog • tube testing eddy current/ultrasonic ATM/KRAUTKRÄMER/FÖRSTER • multiple-head saw MAIR type MC150/7/10 • tube bevelling machine MAIR • brushing machine MAIR • destacker/stacker MAIR • tube bundle destacker MAIR • tube banding machine MAIR/ORGAPACK • emulsion treatment SCHOENAUER • control Siemens S7 • hydraulics

Condition: used, Cut-to-length line Bronx 2050x8mm x35t (A3781) for coil metal cross cutting into sheets of required sizes with different length and width. Dodpfxjq Ulh Hj Ac Nscg Thickness Range: 2 – 8 mm Coil Capacity: 35t Coil OD: 2100mm Coil ID: 508mm , 610mm , 762mm Strip Width: 2000mm – 600mm Sheet Length: 8000mm – 600mm Pack Weight: 10 t Max Line Speed: 60 meters/min Cuts Per Minute: 35 Complete Line With 4 Coil Storage Storage Ramp Coil Loading Car Double Stub Mandrel Uncoiler Sliding Base Hydraulic Expansion Drag Brake Tension Control Peeler / Hold Down Roll 3 Roll Coil Breaker Feed Up Table 7 Roll Backed Up Leveler with Pinch Roll Breaker (9 Rolls Total) Entry Power Pinch Rolls 3 Flights Top & Bottom Back-Up Rolls Entry & Exit Pinch Rolls Marking Unit Measuring Roll Pinch Rolls Bronx Flying Shear AC Die Accelerator Flywheel & Air Clutch and Brake Rack & Pinion Accelerator 35 Cuts per Minute Reject Conveyor Twin Belt Gauging Table Stacker Side Squaring Lift Stacking Tables Photo Cells Drop Type Motorized End Stop Motorized Run Out Conveyor Upgraded AC Motors Upgraded Control Techniques Digital Drives Complete Line

Condition: new, Year of construction: 2024, functionality: fully functional, Incorrect investment by a corporation. Machine is new and unused (already delivered). The machine is available immediately with no lead time. An extremely rare opportunity. Machine type: Horizontal machining center with pallet changer Model series: NHX 8000 Control: Siemens S840Dsl with CELOS Measuring system: fully closed loop scale feedback (X/Y/Z) Machine concept: DCG Travel paths X/Y/Z: 1,400 / 1,200 / 1,350 mm Rapid traverse X/Y/Z: 50,000 mm/min Pallet system: Turn-type pallet changer Number of pallets: 2 Pallet size: 800 × 800 mm Pallet load: 2,200 kg [optional 3,000 kg] Max. workpiece Ø/H: 1,450 mm / 1,450 mm Pallet change time: 16 s B-axis: direct drive Minimum index: 0.001° Maximum speed: 100 rpm Spindle: powerMASTER Speed: 16,000 rpm Dsdpfx Ajxizdaec Njcg Power: 85/50 kW (10% duty cycle / continuous) Torque: 549/279 Nm Taper: HSK-A100 Cooling: central spindle cooling Internal coolant: optional CTS 7 MPa Tool magazine: chain-type, 60 positions [optional 100/120] Rack magazine options: 180 / 240 / 330 positions Max. tool diameter with adjacent tools: 110 mm Max. tool diameter without adjacent tools: 320 mm [for >10,000 rpm: 230 mm] Max. tool length: 800 mm Max. tool weight: 30 kg Tool-to-tool: 1.9 s Cut-to-cut: 5.0 s Equipment / Options: - Workpiece probe - Tool measurement - Laser control (optional) - High-pressure coolant 7 MPa (optional) - Chip conveyor - Fully enclosed enclosure with roof Dimensions n.a. Weight n.a. Connection data n.a.

Condition: used, TWO ROLLS BAR STRAIGHTENER PBVR6 Manufacturer: BRONX Capacity - Bars with tensile strength of 600 N/mm²: Ø 15 - 110 mm - Bars with tensile strength of 700 N/mm²: Ø 15 - 100 mm - Bars with tensile strength of 1.000 N/mm²: Ø 15 - 85 mm Dcsdpoymcn Aefx Ac Nog Roll angle adjustement: 10 to 20 degrees Working direction: Right to Left Scope of supply - Entry chanel - Duo introduction - Straightener - Exit chanel Bars with tensile strength of 600 N/mm²: Ø 15 - 110 mm Bars with tensile strength of 700 N/mm²: Ø 15 - 100 mm Bars with tensile strength of 1.000 N/mm²: Ø 15 - 85 mm Roll angle adjustement: 10 to 20 degrees Working direction: Right to Left

Condition: used, Cut To Length CTL 2000x8, made by BRONX Dcedpsymclbofx Ac Nsg Strip width: 600 - 2.000 mm Strip Thickness: 2 - 8 mm Coil max. weight: 30 Tn Coil Outer Diameter: Up to 2.100 mm Coil Inner Diameter: 508mm - 610mm - 762mm with filler segments Sheet Length Stacker: 600 - 8.000 mm Stacking Capacity: 1 x 8000mm long x 2000mm wide packs Stacking: 10000kg maximum uniformly distributed over 5000mm sheet length Pack Height: 750 mm Max. speed: 60 m/min

Condition: good (used), Year of construction: 2013, grinding diameter 140-355 mm grinding length 3000 mm centre height 260 mm weight of the machine ca. 8,3 t dimensions of the machine ca. 8500 x 3500 mm Dcjdpfx Aceynmpyj Nsg SA 6Ux3000 external cylindrical grinding machine Year of manufacture: 1981 Retrofit: 1 x 2013 SERWEMA Maximum grinding diameter with tailstock: 140 mm Maximum grinding diameter without tailstock: 355 mm Maximum grinding length: 3,000 mm Center height 260 mm Workpiece weight max. 500 kg Machine footprint 8500 x 3500 mm Machine weight 8500 kg