Double-side SIZING & EDGE BANDING machin

IMA Combima /II/230/A/R3

Condition: reconditioned (used), Double-side Sizing-Milling & Edge Banding - First (1st) machine in a line Edges (tape) thickness in rolls (min/max) mm 0,3 / 3 Edges thickness in stips / lippings (min/max) mm 0,4 / 1 Panels thickness (min/max) mm 8 / 45 (60) Gedsyypi Uepfx Aqijka Working width (min/max) mm 236 / 1300 Numerical Control / Software ICOS open (windows XP) Adjustable feeding speed (m/min ) 10 - 50 Without Transmission bar (Master & Slave system) SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Hogging Units (2 x Kw 8) EDGE-BANDING PART (for each side): Glueing Unit (EVA-Hot Melt + Quick Melt Unit) 04.1570 + 283.205 Edge coils supporting unit (No. 6 reels) SERVO-DRIVE guillotine shear (cutting the edge/band) Pressure zone (N.C. adjustment) Fine Trimming unit 08.055 (Kw 1 x 2) 0°-30° Profile Scraping unit 08.519 Glue scraping unit 08.50 Buffing unit 08.617-2 (2 x Kw 0,18) Spraying Unit (for polishing liquid) Milling grooving unit 08.190 (1 x Kw 4,5) 0°-90° / 180°-270°

Condition: new, Year of construction: 2026, For professional and precise glue supply in dowel holes and back side grooves. Short introduction: • Always the same and right glue amount • No afterwards cleaning of the workpieces of too much glue is necessary • Easiest and minimal cleaning (1x week) of the gluing system (through cleaning program) • Glue cost savings • Ergonomic and light glue gun compared to squeezy glue bottles • Faster and more precise working compared to squeezy glue bottles Gkodpsdxz Tpsfx Aqioa

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Vacuum system (with its pump) No. 2 Vertical supporting columns of the top supporting beam No. 1 Horizontal top supporting beam (where the carriage slide on) No. 1 Motorized sliding carriage with horizontal metal arms No. 2 Out-side rollers way (on gound) to in-feed pile of panels to the Loader Out-side motorized rollers table (which receives panels from the Loader) Separate electric and command panel Perimetral safety metal grids Working capacity (cycles/min) 16 (ca.) Gkodefi Tg Hepfx Aqija Min/Max panels thickness mm 10 / 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1300 x 3000 (ca.) Total installed motor power Kw 30

Year of construction: 2004, condition: ready for operation (used), Max. working width: 1000mm, feed rate: 5-20m/min, height: 2200mm, length: 4000mm, weight: 3.3t, with documentation, was maintained regularly. Gkjdji E Trpjpfx Aqisa

Condition: as good as new (ex-display), FULL LINE of Double-side Sizing-Milling & Edge Banding. Composed of the following machines: Gksdpfx Aqodt Rgvjiea VZ0200A) Gantry-portal Loader (Double pick-up station) "BARGSTEDT" Mod. TBH 500/D/30/12 VZ0200B) 1st Double-side Sizing & Edge Bander "HOMAG" Mod. KFL 525/8/A3/15 VZ0200C) In-feeding Rollerway "HOMAG" Mod. TDL 310/30/12 with 90° Turning device (from lenghtwise to crosswise) with double cone system VZ0200D) 2nd Double-side Sizing & Edge Bander "HOMAG" Mod. KFL 526/10/A3/30 VZ0200E) In-feeding Rollerway "HOMAG" Mod. TDL 510/25/12 with 90° Turning device (from crosswise to lenghtwise) with double cone system VZ0200F) Cleaning machine "WANDRES" VZ0200G) Gantry-portal Stacker (Double pick-up station) "BARGSTEDT" Mod. TSP 410/D/25/12

Condition: good (used), The compartments are slanted to the right. Gkjdexq Rklepfx Aqija Support width: 65 mm. For glass height: 2030 mm. Height: approx. 2400 mm. Depth: approx. 3750 mm. Width: approx. 2400 mm. Weight: approx. 1900 kg. Condition: good, second-hand.

Condition: used, Year of construction: 2016, Angular panel saw with automatic pre-loading and twin pusher system for optimised cutting Osi Plus Numerical Control Os Labelling labelling machine with on-board graphic labelling with part drawings Label printing management software Optiplanning Cutting Optimizer Cutting length mm 4500 Cutting width mm 2200 Blade projection 95 mm Motorized rollers for lateral loading on lifting table 4500 x 2200 mm. The translation speed is 10.8 m\min (50hz) - 13.1 m\min (60hz) Automatic recognition of the lost panel (martyr panel) based on the thickness specified in the machine data Low battery stop Automatic side loading buffer. Includes: perimeter nets, double photocell, push-button panel, predisposition electric for the two motorized pre-rollers and the amplification of 4 rollers in place of the fork passages in the pre- intermediate roller conveyor Pre-loading side roller conveyor dim 3800 x 2200 mm with motorized rollers (height from the ground 325 mm) Inertial conveyor for conveying longitudinal trimmings for angular systems 4500 mm (total length 7295 mm) 3000 mm extension to the inertial conveyor to also convey transverse trimmings Long chute for manual conveying of cross-cut trimmings to the centralized inertial conveyor 2050 x 850 mm air curtain discharge table with wheels at the front Air generator up to 6 floors with air curtain MULTIPUSHER 2.4 system with automatic lubrication Additional mobile lateral aligner on the transverse plane. The presence of this device allows to reduce from 1830 to 1220 mm is the minimum length of the panels that must be sent for cross-sectioning. Automatic blade shaft bending detection device for angular systems (longitudinal and transversal) consisting of a sensor that detects the deflection directly on the blade shaft and a device that detects the revolutions blade directly on the spindle. Remote cycle start button panel Automatic panel loading via rear lifting table Automatic double aligner with pneumatic cylinders Additional movable lateral aligner on the transverse plane Gsdpfouc Idxex Aqiska Main blade, max diameter mm, KW 15 Scoring blade, max diameter mm, KW 2.2 Blade carriage speed 1-140 m/min. – BRUSHLESS motors Longitudinal pusher carriage speed 90 m/min. Cross pusher carriage speed 135 m/min. Double pusher carriage with 6 grippers on the longitudinal carriage + 10 grippers on the transverse carriage (8 fixed grippers + 2 on the multi-push system) Cutting system for thin panels

Condition: used, machine/vehicle number: 006279, X axis working area: 3100 mm Y axis working area: 1250 mm Working Table: Flat table Gkedjkw H Ekjpfx Aqisa Number of controlled axes: 3 axes Total number of drilling spindles: 11 Total number of tool changer positions: 8

Condition: excellent (used), Gantry (Portal) machine Movable panel (workpiece), movable working head (Horizontal position of the panel/workpiece) Numerical Control Power Control, Software WoodWOP Safety cabin (enclosure) of the working head and integral safety cabin (enclosure) of the machine In-feeding working table (panel support). Out-feeding working table (panel support) Panels (workpieces) feeding by No. 3 motorized belts - Feeding speed (m/min) max 130 ca. Minimum workpieces dimensions (X - Y - Z) mm 250 x 100 x 15 Gkodpfjgwbbqox Aqija Maximum workpieces dimensions (X - Y - Z) mm 2500 x 1050 x 60 Motorized carpet to evacuate chips and wastes. Separate electric and command cabinet Total installed power: Kw 99 N° 2 WORKING GROUPS (TOP) - (SERVO-MOTOR X-Y-Z ): N° 4 Drilling heads (4 x Kw 2.3) with No. 10 vertical spindles each (total top spindles No. 40) N° 3 WORKING GROUPS (BOTTOM) - (SERVO-MOTOR X-Y-Z ) : N° 6 Drilling heads (6 x Kw 2.3) with No. 40 vertical spindles each (total bottom spindles No 240) N° 2 WORKING GROUPS (HORIZONTAL) N° 2 Drilling heads with horizontal spindles N° 21 Horizontal drilling spindles (Right Side) + N° 21 Horizontal drilling spindles (Left Side) N° 8 Dowel Inserting nozzle & glue injectors(Right side) + N° 8 Dowel Inserting nozzle (Left Side) N° 2 Storage tanks for automatic feeding of the dowels OPTIONAL: WIRELESS BAR CODE SCANNER

Condition: new, Type SK-1000-P6 Working width 1000 mm Min.working length 500 mm Working thickness 2-150mm Polishing roller speed - Frequency control Feeding speed 3-12,5 m/min Godpjdmi Nijfx Aqieka Total motor power 13.87 kW Disc motor 1.5 kW*1 Cross motor 1.5 kW *1 Screw roller motor 2.2 kW *2 Feeding power 2.2 kW Up and down motor 0.37kW*4 Swing motor 0.37kW *2 Working table up and down 0.55 kW Transport dimensions 3650x1850x2100mm Weight 4200 kg