Edge Beveling Machine - KF 200

Knuth KF 200

Condition: good (used), functionality: fully functional, Year of construction: 1991, sheet thickness steel (max.): 16 mm, cutting length (max.): 6,000 mm, HYDRAULIC SHEAR LVD MVSB 62/16 Serial number 18478 Yom 06/1991 TECHNICAL SPECIFICATIONS Max. sheet thickness St45 16 mm Cutting length 6200mm Distance between uprights 6400mm Gap 60mm Range back gauge 1000mm Min. cutting angle 0.5 ° Max. cutting angle 2.5° Min. number of strokes/min. 6 Max. number of strokes/min 25 Min. blade clearance 0.05 mm Max. blade clearance 1.6mm Motor power 30kW Approx weight 35000 Kg LxWxH 7100x2400x3000mm Accessories included; ELGO P85 “GO-TO” for back gauge Electrical adjustment of back gauge 1000mm 1 x Front support 2mtr, one with 90° square arm front support L2000mm Foot pedal Ball bearings on table Inclinable back gauge with manual hydraulic pump Gbjdpfx Ajumhm Aobueh

Year of construction: 1981, condition: ready for operation (used), Working width: 2500mm, max. sheet thickness: 20mm, lateral cylinder support device with three adjustable support rollers and conical bending device, machine provided for exchangeable top rollers up to min. Ø 450mm, machine revision 2009, factory inspection 2012. Gedponvfdbjfx Abuebh

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam Gbsdjhzbipopfx Abujh - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: new, Semi-automatic band sawing machine for cutting solid bars and profiles of medium size with high efficiency and excellent cutting precision. The robust structure gives the machine the necessary rigidity and precision to the cutting unit. Belt drive with two-speed motor and special gearbox with bronze gear and hardened and ground worm screw. Suitably dimensioned flywheels Sturdy ribbon guides made with watertight invitation bearings and adjustable widia plates Belt tension obtained by means of an electromechanical device with microswitch blade rotation control Accident prevention safety device on the flywheel cover cover and on the blade Cutting thickness 1.5 mm Cutting range 60°sx 60°dx Adjustable stop for cuts of the same size Brush belt cleaning device Hydraulic power unit motor 0,37 kW 0.09 kW electric pump for belt refrigeration Jaw height 200 mm Clamp jaw length 185 mm Worktop height 760 mm Gbedpfofibd Tox Abujh Machine weight 820 kg

Condition: used, Year of construction: 2004, Pressure 630 t stroke 800 mm distance between columns 2600 mm Distance table/ram, max. stroke up, adjustment up 1500 mm Table surface area 2500 x 1300 mm pressure of drawing cushion in table 300 t Die cushion stroke in table 300 mm Ram surface 2500 x 1300 mm Side window 1040 mm feed down 600 mm/s Gbedpfjv Svarjx Abueh feed up 360 mm/s working feed 14 - 42 mm/s power requirement 145,0 kW Weight 85,0 t dimensions (WxDxH) 4,2 x 4,0 x 7,8 m height over floor 6,80 m height beneath floor 1,0 m Demonstration machine from technical university with approx. 920 operating hours! Mint condition! permitted for manual loading according to the CE-norm with oil-hydraulic drive, controllable dependent on pressure/time and way, upper and lower stroke limitation, light-guard (Sick) on front and back, hydraulic drawing cushion in table with ejector function, hydraulic cutting impact cushioning, mechanical depth stop via 4 motor-adjustable spindles, hydraulic ram interlocking, two-hand operation 2 tool changing consoles, 4 hydraulic ball roller tracks, 4 dampening elements

Year of construction: 1977, condition: refurbished (used), I sell the double mitre saw Rapid DGS, year 1977. Gjdpfed N Rb Dsx Abusbh Tilting heads Drilling front heads on each side included Very good condition. Available immediately.

Condition: new, Year of construction: 2025, ZGR-3140/1,0 Our products are best quality and have certificate CE. Gbjdpfx Abecntnkjuoh Plate Bending Machine ZGR-3140\1,0 + additional equipment Technical data: - Maximum working width: 3140 mm - Sheet gauge up to: 1,0 mm (Steel) - Titan-Zinc-Plate 1,0 mm, Aluminium Plate 1,8 mm Cooper plate 1,5 mm - Max. bending angle: 145 degrees - Rotary shears cut to full working length - Thickness of bending bar: 20 mm - Protractor - Weight: 600 kg - Rotary shears (max. plate gauge 0,8 mm / Steel) + 350 Euro - The machine have certificate CE and 12 months warranty.

Condition: new, Year of construction: 2024, A vineyard post roll forming machine is used for vineyards and orchards to produce the stakes and posts. Normally, grape posts are 1.5-2mm thickness. The production line consists of Decoiler, Servo Feeder Straightener, Press, Stamping Tool, Roll Form Machine and Shear. Gbjdet Tcz Uepfx Abujh

Condition: good (used), Plant: REWA Chamber Filter Press used Type: 470-15-25K-HP Design: side rail guided Gbodpfsqakbrsx Abueh Filter plate format: 470x470 mm Number of plates: 15 Filter plates: PP Filter cloths: optionally available in coordination with the medium Press capacity: approx. 57 dm3 Filter pressure: approx. 15 bar Material of parts in contact with the product: Flange, feed-throughs stainless steel, PP or rubberized Material of parts not in contact with the product: Stainless steel Purchase or hire: Inspections of the systems by arrangement at our factory. Other: We can supply you with used equipment ready for operation or refurbished according to your wishes and requirements. Would you like to rent or buy this system? Please contact us, we are at your disposal.

Condition: new, The NEOMIG-i 500 G is a three-phase multiprocess welding machine with separate wire feeder. Its advanced digital technology and its duty cycle ensure excellent arc characteristics for industrial MIG/MAG applications. The integrated synergies facilitate setup and reduce spatter during welding. Equipped with the WF wire feeder, it offers a control precise welding parameters to ensure perfect quality. MULTI-PROCESS MIG/MAG : Gedpsmxkdpefx Abuebh - steel and stainless steel wire: Ø 0.6 to 1.6 mm - aluminum wire : Ø 0.8 to 1.6 mm - CuSi and CuAl wire : Ø 0.8 to 1.6 mm - flux-cored wire (reverse polarity) : Ø 0.9 to 2.4 mm MMA DC / Pulsed : basic, rutile and cellulosic electrodes. TIG DC Lift / Pulsed. Gouging.