Welding machine

LD-Laser GY-W200

Condition: ready for operation (used), Year of construction: 2009, operating hours: 9,192 h, travel distance X-axis: 1,200 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 500 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, spindle speed (max.): 16,000 rpm, number of axes: 3, This 3-axis HERMLE C 1200 vertical machining centre was manufactured in 2009. It features an impressive X-axis travel of 1200 mm, Y-axis travel of 900 mm, and Z-axis travel of 500 mm. The machine is equipped with a spindle speed of 16,000 rpm and includes 30 tool stations. If you are looking to get high-quality machining capabilities, consider the HERMLE C 1200 machine we have for sale. Contact us for further details. • X – 1200 mm • Y – 900 mm • Z – 500 mm • Machining Center C 1200 V • Heidenhain iTNC 530 contouring control • Spindle 16,000 rpm • SK 40 • 30 Tool Stations • Rigid Clamping Table • Coolant System • Electronic thermal compensation (iTNC) with temperature sensors on the motor spindle and machine base • Portal design with a closed rear wall for significantly better support during torsional loads • Two axes are located in the tool, providing very good mass distribution and ideal conditions for high rapid traverse and feed rates Fjdoylw Stopfx Apwsgb • Feed screw diameter and pitch (X and Z axes): 40 / 20 mm • Feed screw diameter and pitch (Y axis): 50 / 20 mm • Direct measuring system • Resolution: 0.0001 mm • Position tolerance (Tp) in X-Y-Z axes according to VDI/DGQ 3441: 0.010 mm • Recommended ambient temperature for maintaining accuracy: 20 °C ± 1 °C • Flushing/wash-down system for rinsing the side work area • Display: 15" TFT color flat screen • Flexible contour programming • Part program memory • Tool diameter capacity: 80 mm • Tool diameter with free adjacent slots: 125 mm • Maximum tool length: 300 mm • Maximum tool weight: 8 kg • Maximum magazine load: 120 kg • Chip-to-chip tool change time according to VDI 2852: 6.5 seconds • Manual control unit includes electronic handwheel, axis direction keys, feed control, rapid traverse, emergency stop, and enable switch • Machine on – 11,927 h • Spindle on – 9,192 h Additional equipment • Chip conveyor • Heidenhain touch probe • Electronic Manual Control Module (iTNC) Technical Specification Taper Size SK 40

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. Fgedeq Nf Enopfx Apwsb 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.

Condition: used, Laser ACSYS Lasertechnik GmbH PIRANHA II Multi FL20s Fedou E U Tnjpfx Apwjgb

Year of construction: 2005, condition: like new (used), Quality used Bystronic Pr 100 8axis cnc pressbrake for sale BYSTRONIC PR100 x 3100 100 ton x 3100mm 8 Axis CNC Hydraulic Down stroke Press Brake complete With Cybelec Modeva 10S Control. Manufactured 2005 – fully serviced with Bystronic uk from new Specification Year of Manufacture /new 2005 Control Cybelec Modeva 10S Back gauge Programmable Guards Fiessler AKAS Capacity 100 Ton Maximum length of bend 3100mm / 3metre Extended Daylight – to be confirmed Max stroke 315mm Rapid approach 180mm/s Bending cycle 10mm/s Rapid return 150mm/s Tooling top and bottom Wander type footswitch Total 8 axis Y1,Y2,X1,X2,R1,R2,Z1,Z2 – 6axis back gauge Hydraulic Crowning We can quote for delivery and installation complete with operator training Fgsdpfjhufktsx Apwjb We can advise and supply brand new tooling to produce your sheet metal products on this cnc press brake

Condition: excellent (used), functionality: fully functional, Werner & Pfleiderer Twin-Screw Extruder ZSK 40 – Excellent Condition For sale is a Werner & Pfleiderer (WP) ZSK 40 co-rotating twin-screw extruder. Technical Specifications: • Machine Type: ZSK 40 • Screw Diameter: 40 mm • Screw Length: 7 barrels × 4 D → approx. 28 L/D • Main Drive: 34.5 kW • Motor Speed: 1,800 rpm • Screw Speed: 40 – 400 rpm • Max. Torque per Screw Shaft: 325 Nm • Heating: Electric, connected load approx. 17 kW • Cooling: Water chiller unit • Temperature Control Zones: 6 zones • Barrel Temperature Sensors: 6 • Material Temperature Sensor: 1 • Material Pressure Sensor: 1 Barrel Configuration: • Feed barrel with liquid injection port • Open barrel with insert and 2 liquid injection ports • Multiple closed barrels with ports for liquid injection or measurement points • Degassing barrel Fodpfjycuuyex Apwogb General Features: • Co-rotating, closely intermeshing (self-cleaning) screws • High mixing and dispersing performance thanks to modular mixing and kneading elements • Modular system for screws and barrels • Drive section and process section mounted on stable base frame Fields of Application: • Plastics compounding • Masterbatch • Additive and filler incorporation • Laboratory and pilot plant use • Formulation and product development Condition & Runtime: According to the operating hour counter, the machine has run for less than one year and is therefore in excellent, nearly as-new condition. The screw elements are also as new. Options & Customizations: Upon request, we can design and install suitable tooling, such as strand dies, and integrate additional peripherals such as screen changers, pelletizing units, dosing technology, or other customer-specific components. The machine can thus be configured and delivered ready-for-operation according to customer requirements.

Condition: used, Year of construction: 2017, machine/vehicle number: A1711012, Pos.1 VEN CLEAN Smart dedusting systemCompressed air dedusting for cleaning the workpieces to be painted from dust on profiled workpiece surfaces. Five rotating blowing stars are installed. These remove the dust from the surface. The loosened dust is extracted on both sides by suction shafts. on both sides. An external extraction system is required on site. Technical data: Roller transport length: 2,060 mm Roller pitch: 85 mm Working width: 1,300 mm Total width: 1,800 mm Drive power: 0.25 kW Exhaust air volume: 4,000 m³/h To be provided by the customer Compressed air consumption: 980 Nl/min. Fjdpfxeu U Ryyo Apwogb Ionisation as nozzle bar, not EX) with compressed air nozzles, Compressed air consumption 840LN/min. Pos. 2 Automatic spray gun VEN SPRAY Comfort- Manufacturer Venjakob - Type. VEN SPRAY Comfort CNC 7000 - Year of construction 2017 - Working height approx. 930mm+-20mm - Working width 1300 mm - Operating side left - Price for overhauled machine - Actual condition, machine not overhauled - Gun drive in duo version - Dry extraction system - Extraction nozzle diameter 500 mm - Exhaust air capacity 10.000 m³/h - Belt conveyor system - Infinitely variable feed speed ~ 2-6 m/min - With belt cleaning system with doctor blade in tungsten carbide design - With option to install a second beltcleaning system. Software and electric parts inside. - Gun control, touch screen CNC7000 - Installed colour circles 1 pc. (optionally more possible) - Supply air filter cover - Suitable for water-based paints - Suitable for solvent-based paints - Control cabinet, free-standing - Length: 4.350 mm + (2,060 mm) - Width: 3.540 mm - Height: 2.600 + 440 mm - Volt, Hz 400 / 50 - El. Power 23,33kW / 63A - Colour RAL 7035 - Location, in stock Voltage fluctuations max. +/- 5 % _____ Optionally, we can also provide you with a quotation for the assembly and start-up of the system, as well as training for your employees. We also offer regular maintenance and servicing of the machine on request. For further information, get in touch with us!

Condition: excellent (used), 5-axis Year of production: 2018 Machine working area dimensions for the X and Y axes: X 2100 mm Y 3100 mm Head stroke in the Z axis: 1250 mm Fgodpfx Ajun Rqgjpwob Machine travel speed X, Y. Z: X: 80 m/min Y: 80 m/min Z: 12 m/min Vacuum table BECKER pump HITECO spindle in the HSK 63F standard Price of a new machine: approx. 135.000 €

Condition: new, Year of construction: 2026, The front-opening sandblasting booth is a significant convenience for large and heavy workpieces. Telescopic actuators mounted in the door facilitate opening. As a standard, the sandblaster has a built-in dust extractor generated during sandblasting. Equipped with a set of nozzles, a gun and protective stickers for the visor. Machine description Dust-free operation of the device is ensured by the use of circumferential gaskets, which allows you to perform work in an environmentally friendly manner. The sandblasting hose is placed in the lower part of the collection container. Drain hole allows quick change of blasting material. The sand blaster is used for cleaning and processing various types of surfaces, e.g. removing rust, paint, deposits from metal surfaces, e.g. automotive parts, engines, fittings, housings, wheels, rims, etc. The following can be used as an abrasive: , silicon, glass beads, plastic sand, emery and other materials. KDP450TOP technical parameters CAPACITY 450L (0.45m3) AIR CONSUMPTION 400 - 1000 l/min Fedpfjm Nccxex Apwogb OPERATING PRESSURE 4 - 8 BAR AIR CONNECTION 1/4" (INCH) QUICK RELEASE VIEW AREA 580 x 270mm DRAIN CONNECTION fi 64mm and 90mm CAB INTERNAL DIMENSIONS (Width x Depth x Height lowest/highest point) 1140 x 650 x 630mm DIMENSIONS 1260 x 1000 x 1600mm WEIGHT 105 kg Standard equipment DC15 cyclone exhaust Working field lighting - 12 V fluorescent lamp with 230 V power supply with switch 2 high-quality work gloves made of rubber, integrated with the device 2 suction (vent) connections with a diameter of 64 mm and 90 mm for connecting a suction device Sand blasting gun with four replaceable ceramic nozzles 4 pieces of replaceable protective film for the window, viewfinder front door with rubber perimeter seals for dust-free operation Manual in English We kindly inform you that the device requires self-assembly. We kindly inform you that the device requires self-assembly. The price is a net price. Price does not include shipping costs. For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website.

Condition: refurbished (used), Year of construction: 2021, functionality: fully functional, center height: 150 mm, workpiece weight (max.): 130 kg, grinding length: 1,500 mm, grinding wheel diameter: 500 mm, total width: 2,155 mm, total length: 5,465 mm, total height: 1,700 mm, grinding diameter: 300 mm, grinding wheel width: 63 mm, The cylindrical grinding machine was fully overhauled in 2021 and has hardly been used since. The condition of the machine is practically like new. Equipment as shown in the photos. The machine is connected to power and can be inspected at any time by prior arrangement. Fgsdjx A Dfyepfx Apweb Technical specifications: Grinding diameter: 300 mm Grinding length: 1500 mm

Year of construction: 2022, operating hours: 108 h, condition: refurbished (used), machine/vehicle number: SN2120, EDM312MF30-SLM (second-live machine) Technical data: Adjustment travel: 450x300x300mm Fgedpfx Apshtrdyeweb workpiece clamping table 820x400mm tank size 900x520mm filling height 300mm distance table/electrode holder 150/450mm workpiece weight max. 800Kg Dielectric max. 700l dimensions WxDxH 2700x1800x2350mm Machine weight 2500kg Mains connection 3/N/PE 400/230 50Hz power consumption 6,7 KVA Equipment: Color: new painting light grey + telegrey New control cabinet New control APC910/2 (win10) User interface MF30 V 2.8 New drives B&R with Endat interface Screen touch screen Generator exopuls+ 60A Rev.4 WZW 5-fold Touch protection operable via push button Linear scales in all axes X, Y, Z (Fagor) cartridge filter 2 pieces Cooling unit Termogamma Complete new machine installation New ball screw, bearing, coupling Maintenance unit with digital pressure switch Valve island Co² extinguishing system C-axis Hirschmann 50/min., holding brake Refurbished Manual control bar with enabling button Lowering tank automatic tracking chuck Erowa IST, Hirschmann, 3R Warranty 12 months Transport commissioning on site training