Welding Smoke Suction

LINCOLN M200M BIA CPL

Condition: excellent (used), belt driven Flow rate 14500 m3/h Negative pressure 3091 Pa Motor power 22 kW Speed ​​2340 rpm Suction DM 500 mm Outlet DM 400 x 500 mm Dimensions L x W x H = 1800 x 1300 x 1250 mm Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. Gusdpfjh Tfqhex An Iog • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Year of construction: 2011, condition: excellent (used), Cloos welding robot Qirox QRC 320 incl. control system V 6, stand base for vertical arrangement, Cloos welding machine Quinto II 603 (600 A), wire feeder, welding torch, torch hose package, mechanical cleaning, pressure amplifier Gjdpfeizwv Nox An Isug 1 tilting and rotating table WPK 5000, load capacity 500 kg, 1 start pre-selection, 1 control unit for customer-supplied sliding door Gas nozzle sensor, arc seam tracking, point editor System will be completely overhauled and serviced before delivery. A second station with another identical tilting and rotating table is possible.

Condition: good (used), Year of construction: 1999, CONFIGURATION, ARCHITECTURE: PARALLEL LATHE GUIDANCE: PRISMATIC, 3 WAYS THE CARRIAGE CAN MOVE WITHOUT INTERFERING WITH THE TAILSTOCK AND STEADY RESTS, ESPECIALLY SUITABLE FOR SHAFTS DISTANCE BETWEEN CHUCK AND TAILSTOCK: 6000 mm CHUCK DIAMETER: 1000 mm SWING OVER BED: 1020 mm TURNABLE DIAMETER: 700 mm BED WIDTH: 900 mm LOAD CAPACITY BETWEEN CHUCK AND TAILSTOCK: 12,000 kg 4-POSITION AUTOMATIC TOOL TURRET: YES MOTORIZED TAILSTOCK: YES SPINDLE SPEED: 1–720 rpm CONTROL (BRAND/MODEL): SIEMENS 840 D POWER LINE AIR CONDITIONING IN ELECTRICAL CABINET: YES CHIP CONVEYOR: YES, DRAG-TYPE, NEW IN 2021 EXTRAS OPEN STEADY REST: 2 UNITS Gjdpeyhrnuofx An Ieug CLOSED STEADY REST: 1 UNIT INSTALLED MACHINE DIMENSIONS (L x W x H): 14 x 3 x 2.5

Condition: new, grinding range 2 - 13 mm sharp cornered angle min./max. 90 - 140 Grad connected load 230 V weight of the machine ca. 10 Kg Gjdpfxsupxdqj An Ioug dimensions of the machine ca. 0,35 x 0,2 x 0,2 m

Condition: excellent (used), Year of construction: 2010, feed length X-axis: 650 mm, feed length Y-axis: 500 mm, feed length Z-axis: 475 mm, feed rate X-axis: 6,000 m/min, feed rate Y-axis: 6,000 m/min, feed rate Z-axis: 6,000 m/min, table width: 450 mm, table length: 1,530 mm, X-Axis: 650mm Y-Axis: 500mm Z-Axis: 475mm Table Length: 1530mm Table Width: 450mm Gedsxtmqtspfx An Ieug Table load: 350 Spindle speeds: 55 - 4000Rpm Feed rate X-Axis:6000mm/min. Feed rate Y-Axis:6000mm/min. Feed rate Z-Axis:3000mm/min. Length: 2300mm Width: 2550mm Height: 2200mm Weight: 2850kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), 3 machine vices Goody. Gsdpfxorai Akj An Ijug

Condition: new, Year of construction: 2026, The CORMAK HBS260 metal bandsaw for cutting pipes, profiles and bars is widely used in locksmith and metalworking workshops where precision, quality and cutting speed are essential. The model features a pivoting arm from 0° to 60°. The frame design ensures precise and quiet operation. It has a removable chip tray for easy cleaning! Machine characteristics The CORMAK HBS260 horizontal metal bandsaw with a pivoting arm enables cutting perpendicular to the material axis and at any angle within the range of 0° to 60°. The material can be fed manually or by any mechanical device, while the tool feed operates automatically. The blade guides are fitted with special carbide plates and bearings, which have a significant influence on the blade’s guidance, service life, straightness, accuracy and cutting quality. The carbide guidance system greatly reduces machine and blade wear. The machine is equipped with an efficient coolant pump with a closed coolant circulation system. The saw arm is made from a single cast-iron element, and with the use of a 27 mm wide cutting blade, it enables series cutting of both profiles and solid materials. The vice is mounted on an adjustable base and features a quick-clamping system. The blade guides are fitted with hard metal (carbide) plates and rolling bearing systems. These carbide guides are responsible for the cutting precision and straightness. The upper part of the base is shaped as a tray for draining coolant and collecting chips generated during the cutting process. The base is fitted with a cast-iron worktable with a pivoting arm and a control panel mounted on a separate arm. In the cutting process, the main cutting motion is the movement of the cutting blade, while the feed is achieved by lowering the arm. The arm lowering speed (cutting speed) is controlled by a hydraulic cylinder. The feed rate is regulated via the saw’s control panel. Two blade speeds are available: 35 and 70 m/min. When the arm reaches its lower position (after the cut), the drive to the cutting blade is automatically switched off. Safety is ensured by blade guards and micro-switches that stop the motor after the cutting cycle or when any guard is opened. Additional protection automatically switches off the bandsaw in the event of blade breakage. Blade size [mm] 2520 x 27 x 0.9 Blade tension mechanical (manual) Gjdpfx Aeudi Uzen Isug Blade speeds [m/min] 35, 70 Arm lowering control stepless – hydraulic cylinder Vice base height [mm] 860 Saw wheel diameter [mm] 300 Saw frame swivel [°] 0–60 Power supply 3-phase 400V Main motor power [kW] 1.1 / 1.5 Coolant pump motor power [kW] 0.05 Dimensions with base [cm] 150 x 80 x 140 Weight [kg] gross/net – 210 / 180 kg Additionally 2 M42 saw blades 5L Emulsol ZW580 magnetic chip collector

Condition: as good as new (ex-display), Year of construction: 2026, SRF Master, illustration on the left 2 m extraction arm Application area Low amounts of smoke/dust Occasional use Benefits Requires little readjustment of the extraction hood More flexible due to the additional hose connection at the rear Features Safe operation thanks to filter monitoring Extraction hood can be rotated and swiveled 360 degrees Sliding handle and cable holder Process: 3-stage Filter type: Disposable filter Filter area: approx. 12 m² Gedpfxjdqzbro An Ieug Separation rate: > 99% Filter material: Glass fiber fleece Welding fume separation class: W3 Additional filters: Two pre-filters Basic data Extraction capacity: max. 950 m³/h Diameter of extraction arm: Ø 150 mm Length of extraction arm: 2 m Diameter of suction connection: Ø 150 mm Power connection: 230 V / 50 Hz Motor power: 1.1 kW Sound pressure level: 72 dB(A) Dimensions (W x D x H): 705 x 655 x 900 mm Weight: approx. 71 kg

Condition: excellent (used), Year of construction: 2009, operating hours: 29,000 h, functionality: fully functional, Equipment: documentation/manual, The INDEX C200 – manufactured in 2009 – is a powerful CNC production turning center with a FANUC 31i control, main and counter spindle, and a 65 mm bar capacity. The machine features a high-quality 3-turret design, with turrets 1 and 2 each equipped with X, Z, and Y axes, and turret 3 used for machining on the counter spindle. All three disc turrets are equipped with 10 stations and, with driven tools up to 6,000 rpm, enable highly flexible complete machining. With a portal parts handler, conveyor belt, C-axes on the main and counter spindles, and powerful spindle drives, the machine is particularly suitable for productive series production of complex turned/milled parts. Control: FANUC 31i Design: Machine with 3 tool holders / 3 disc turrets Bar capacity: 65 mm Machine bed: Vertically arranged gray cast iron machine bed Main spindle: Spindle 4 Counter spindle: Spindle 5 with Z-axis Spindles Main spindle Bar capacity: 65 mm Spindle diameter at front bearing: 110 mm Spindle nose: ISO 702/1, Size 140 Cyl. Chuck diameter: 160 mm Power: 25 kW at 100% ED / 33 kW at 40% ED Torque: 112 Nm at 100% ED / 150 Nm at 40% ED Speed: 5,000 rpm C-axis: Resolution 0.001° Counter spindle Bar capacity: 65 mm Spindle diameter at front bearing: 110 mm Spindle nose: ISO 702/1, Size 140 Cyl. Chuck diameter: 160 mm Power: 25 kW at 100% ED / 33 kW at 40% ED Torque: 112 Nm at 100% ED / 150 Nm at 40% ED Speed: 5,000 rpm C-axis: Resolution 0.001° Counter spindle Z-axis: 700 mm travel Rapid traverse Z-axis: 50 m/min Tool holder / Turret Design with 3 disc turrets, each with 10 stations. Tool system with 10 stations: Cylindrical shank DIN 69880 – Ø30 x 55 mm. Tool holder 1 X, Z, Y axes 10 stations X-axis: 110 mm Z-axis: 320 / 550 mm (according to documentation) Y-axis: 100 mm, ±50 mm Driven tools: 6.5 kW / 16 Nm / 6,000 rpm Tool holder 2 X, Z, Y axes 10 stations X-axis: 110 mm Z-axis: 550 mm Y-axis: 100 mm, ±50 mm Driven tools: 6.5 kW / 16 Nm / 6,000 rpm Tool holder 3 X-axis 10 stations Used exclusively for machining on the counter spindle X-axis: 180 mm Driven tools: 6.5 kW / 16 Nm / 6,000 rpm Further technical equipment according to documentation Portal parts handling system with numerically controlled Z-axis Workpiece removal from main or counter spindle to conveyor belt Removal of scrap material from the main spindle into a scrap container Portal parts handler: Traverse speed: 100 m/min Traverse range: 70 mm Workpiece diameter max.: 90 mm Workpiece length max.: 250 mm Scrap length max.: 250 mm Workpiece weight max.: 3.5 kg Hydraulic system: Flow rate: 19 l/min System pressure: 90 bar Hydraulic tank: 40 l Coolant circuit: Flow rate: 19 l/min Coolant unit power: 13 kW Coolant system: Pump output: 80 l/min / 8 bar Tank capacity: 300 l Gjdjy Tmhzopfx An Ioug Chip conveyor: Chip discharge height: 1,250 mm

Year of construction: 2009, condition: new, Belt dimensions: 2000x100 mm Belt speed: 30 m/s Gsdpfox Davex An Isug Angle adjustable from 30 to 90° Power: 3 kW, 4000 V, 50 Hz Weight: 200 kg Rollers for grinding reamers: 3/4"; 1/2"; 1"; 1 1/4"