Board packaging line

Condition: ready for operation (used), Year of construction: 2009, machine/vehicle number: 19500648, functionality: fully functional, workpiece length (max.): 3,500 mm, workpiece width (max.): 130 mm, workpiece height (max.): 120 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Max. profile length: 3,500 mm Max. profile width: 130 mm Max. profile height: 120 mm MACHINE DETAILS Number of milling and drilling units: 7 Max. Friedrichs motor speed: 18,000 rpm Rodjzln D Eepfx Am Tscd Max. machine motor speed: 1,500 rpm Electrical operating voltage: 400 V, 50 Hz Required network voltage: 20 kW Cable connections: 400 V NPE Operating height of the control cabinet: 1,050 mm Pneumatic operating pressure: 6 - 7 bar Pressure consumption per cycle: Approx. 3,500 NI Pneumatic line pressure at 70 °C: Approx. 15 bar EQUIPMENT Automatic screw feeder Arrangement of the units: On a wheel, which enables machining at different angles.

Condition: excellent (used), Year of construction: 1995, Combination Unit: Manufacturer: GSG Feeder: Type: 840.02-027 Crusher Descaler: Type: 663.02-017 Wire Range: Ø5.5-16mm For wire rod with approx. 40-60 daN/mm² strength Rcjdpfor Nfvmox Am Tjd Crushing and Bending Rollers: Carbide Inserts Adjustment with 0.37 kW - 1.15 A gear motor Brush Drive with 0.25 kW gear motor, n=293 rpm Connection Voltage: 380-420 V 50 Hz Dry Coating Unit: Type: BSG/T Filling: Calcium Stearate (e.g., Traxit Type: D S 51 E) Stearate Consumption: approx. 350 g per t of wire Drawing Speed: max. 15 m/s Electrical Power: 2x 0.55 kW gear motors Cassette: 2 slots (supplied with 1x roller block + 1x cassette) Type: PKG/T (TS) Cleaned rolled wire Wire strength approx. 40–60 daN/mm² Wire range max. inlet diameter 9.5mm, finished diameter 3.5–8.5mm Roll dimensions min. Ø115mm, max. Ø125mm, Bore diameter Ø82mm, width 15–25mm Cooling pin diameter 25mm Cooling water consumption approx. 600 l/h Drawing machine: Manufacturer: Koch Type: KHZ 5000 Year of manufacture: 1993 Serial number: 13.821 Number of draws: 1 draw per block Drawing drum: Ø700mm Tensile force: mechanical 5000 N Wire material: mild steel wires Run-in strength: approx. 40 – 45 daN/mm² Maximum drawing range: Inlet diameter 5.0 – 8.5mm Cross-section reduction: 20 x 25% (mechanical gradation) Drawing speed: up to max. 7.0 m/s Brake: Twiflex, type: MRB Drive: AC motor/frequency converter, Siemens PN=110 kW, n=1485 rpm Spooler: Manufacturer: Koch Type: KHS 1250 Year of manufacture: 1993 Factory No.: 13741 Wire diameter: 5 – 8.5 mm Strength: approx. 55 – 70 daN/mm² Winding speed: V=7 m/s, adapted to the drawing machine Filling weight: approx. 3000 kg Spool drive motor: Three-phase motor with external fan Type: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000-2000 rpm, IP54, design B3 Laying drive motor: 66-671U, 1.5 kW, 170 V, 9.8 A, 1680 rpm, IP 44, B5-200 With Attached tachometer generator TG 20, 20 V / 1000 rpm With attached spur gear SK 32, i=57.53, design B6 Hydraulics: Hydraulic excavator type: H13 AK Pneumatics: Twiflex disc brake type: MRB Pneumatic cylinder type: SPWG 28032-25mm stroke Dimensions: 3100 x 3000 x 1700 mm (L x W x H) without counterweight

Condition: ready for operation (used), Year of construction: 2006, machine/vehicle number: 19500624, functionality: fully functional, operating pressure: 7 bar, rotational speed (max.): 18,000 rpm, working height: 1,000 mm, No minimum price – guaranteed sale to the highest bidder! The new price of the machine was €950,000! TECHNICAL DETAILS Milling units / Motor power Motor power, small milling cutter: 0.27 kW Frequency, small milling cutter: 300 Hz Speed, small milling cutter: 18,000 rpm Motor power, large milling cutter: 1.1 kW Frequency, large milling cutter: 200 Hz Speed, large milling cutter: 12,000 rpm Tool data / Milling cutter data Collet diameter, small milling cutter: max. 8 mm Milling cutter diameter, small milling cutter: max. 8 mm Collet diameter, large milling cutter: max. 10 mm Milling cutter diameter, large milling cutter: max. 14 mm Electrical data Operating voltage: AC 400 V 3 N/PE Frequency: 50 Hz Redpjzlnxisfx Am Tjcd Rated current: 35 A Control voltage: 24 V Pneumatic data Working pressure: 0.7 / 1 MPa (7 / 10 bar) Compressed air consumption: 170 l/min Load limit of pneumatic lines at 70 °C: approx. 15 bar Working height Working height: 1,000 mm EQUIPMENT Clamping units Vertical clamping Maintenance unit with filter pressure regulator Control cabinet / Saw with lockable main switch Cutting unit: Allows cutting angles of 45 degrees and 90 degrees Machining units: Includes machining units and profile bearings Tools: Two screwdrivers, three cut-off wheels

Year of construction: 2005, condition: ready for operation (used), functionality: fully functional, power: 14 kW (19.03 HP), input current: 80 A, workpiece length (max.): 4,000 mm, machine/vehicle number: 6080008129, TECHNICAL DETAILS Maximum profile width: 130 mm Maximum profile height: 205 mm Maximum workpiece/profile length: 4,000 mm Processing capacity: 80 units MACHINE DETAILS Connection: 3 N/PE 400 V Frequency: 50 Hz Current: 80 A Power: 14 kW Redpfezlnvusx Am Tjcd EQUIPMENT Powered, continuously adjustable gripper Lifting function for smooth feeding Profile guidance on rollers Internal gripper to prevent damage to the profiles Integrated measuring sensors for workpiece length control Workpiece removal via outfeed table Portal design for high profile cross-sections Industrial PC with Windows operating system Barcode scanner

Condition: new, Year of construction: 2022, functionality: fully functional, TAKAMAZ CNC Compact loader FC60 Lathe with automatic loader unloader quickest loading system in the world loading time new part 2,8 sec. loading cap. till 60 mm diameter. loading lenght max 50 mm max weight 1 kg per side loading feed 120 m min include part turning for loading Fanuc Control full warranty 2 year Lathe spec. Spindle motor 7,5/5,5 kw turning diameter max 180 mm turning lenght 240 mm bar cap. 35 mm Rcjdpfxom E I D Hj Am Tsd collet chuck 173E till 40 mm diameter spindle nose A2-5 spindle speed 4500 rpm tool pos 8 stations tool shank 20x20 mm boring holder 25 mm diameter rapid speed X/Z 18/24 meter machine dimension 1,36 x 1,37 meter height 1,7 meter weight 2,7 ton total power 14 KVA Price is EXW (Stock Europe), Include loaded on truck. Transport, installation, commissioning, training, and yearly service contracts are available upon request for an additional fee. Installation and training is always done by our high qualified Service team in 3 locations in Europe. Netherlands, Germany, Romania.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2015, operating hours: 4,125 h, load capacity: 8,000 kg, lifting height: 3,600 mm, mast type: duplex, fork length: 2,050 mm, overall weight: 13,948 kg, An oil change was performed before the sale. Only the hydraulic oil was not changed. The filters have been replaced. TECHNICAL DETAILS Load capacity: 8,000 kg with load center at 900 mm Residual load capacity with Kaup 10T160 fork positioner: 7,320 kg with load center at 900 mm Tractive force with/without load: 45.6 kN Lifting height: approx. 3,600 mm Fork length: approx. 2,050 mm Rodozlhnqepfx Am Tecd MACHINE DETAILS Engine: LPG GM 5.7L V8 Cylinders: 8 Displacement: 5,700 cm³ Rated speed: 2,200 rpm Power: 85 kW Operating hours according to display: approx. 4,125 h Operation: Solo-Pilot with multi-function display Dimensions & Weight Overall length including forks: approx. 5,950 mm Overall width: approx. 2,150 mm Height with mast retracted: approx. 3,160 mm Height with mast extended: approx. 4,960 mm Height above protective roof: approx. 2,705 mm Self-weight: approx. 13,948 kg EQUIPMENT Kaup 10T160 fork positioner Duplex mast 3rd + 4th control circuit Side shifter Solo-Pilot Single pedal control Work lights front and rear Full cabin with heater Note: The two tires on the steering axle, as well as the fork tines, should be replaced. This can be requested and carried out by the seller. Fork tine length would be selectable.

Condition: used, Year of construction: 2007, operating hours: 39,023 h, machine/vehicle number: 1315318, laser power: 5,000 W, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, workpiece weight (max.): 900 kg, No minimum price – guaranteed sale to the highest bidder! The machine has not been powered on for approximately one year. TECHNICAL DETAILS Laser power: 5,000 W Working area (X x Y x Z): 3,000 mm x 1,500 mm x 115 mm Sheet metal thickness, structural steel max.: 25 mm Sheet metal thickness, stainless steel max.: 20 mm Sheet metal thickness, aluminum max.: 12 mm Maximum workpiece weight: 900 kg Positioning speed max.: 300 m/min Positioning accuracy: +/- 0.1 mm Rcedezlhcnepfx Am Tsd MACHINE DETAILS Control system: CNC Siemens Sinumerik 840 D Operating hours, laser on: 77,107 h Operating hours, beam on: 39,023 h Dimensions & Weight Machine dimensions (L x W x H): 11,100 mm x 4,600 mm x 2,400 mm Machine weight: 12,000 kg EQUIPMENT Automatic pallet changer NitroLine FocusLine PlasmaLine SprintLine ContourLine

Year of construction: 2008, condition: excellent (used), SMG HZPU 8000-3000/2100-S1 Hydraulic Drawing Press Rcjdpfx Aen Awd Rsm Tod Brand SMG Type HZPU 8000-3000/2100-S1 Year 1995 Description Hydraulic Drawing Press H frame hydraulic press Pressing force 800 ton Clamping area Approx. 3,000 x 2,100 mm Installation height Max. 1,400 mm

Year of construction: 2010, condition: ready for operation (used), functionality: fully functional, working length: 7,600 mm, machine/vehicle number: 1400040505, number of axes: 4, TECHNICAL DETAILS Rsdpfx Ajzhuyfom Tscd Max. machining length with end face machining: 7,600 mm Max. machining length without end face machining: 7,720 mm EQUIPMENT 12 pneumatic collet chucks 2 work areas 4-axis profile machining center; stepless machining between -90° and +90° with each available tool Automatic clamping position adjustment with absolute measuring system Two separate machining zones for tandem operation 4-axis control 18.5" color monitor, USB ports, and network connection Windows operating system EluCam software Automatic profile length measurement (on both sides) Barcode scanner The traversing tool magazine ensures short tool change times and thus optimal machining cycles; the magazine can be equipped with eight tools. 8x tool holders with collet chucks

Condition: ready for operation (used), Year of construction: 2005, operating hours: 20,729 h, functionality: fully functional, travel distance X-axis: 980 mm, travel distance Y-axis: 630 mm, travel distance Z-axis: 630 mm, controller model: Heidenhain iTNC 530, rotational speed (max.): 18,000 rpm, TECHNICAL DETAILS Travel range X-axis: 980 mm Travel range Y-axis: 630 mm Travel range Z-axis: 630 mm Spindle speed range: 0–18,000 rpm Tool holder: HSK 63 Rjdpfx Aszmry Tem Tjcd MACHINE DETAILS Control system: Heidenhain iTNC 530 Clamping area: 1,250 × 700 mm Operating hours Machine operating hours: 46,922 h Program runtime: 20,279 h Spindle operating hours: 20,746 h EQUIPMENT Fixed angular table 3D measuring probe Heidenhain Tool measurement in the working area with BLUM laser Vertical tool changer with 32 magazine slots Full protective enclosure with sliding doors and interior lighting Electronic handwheel Operating modes 3 and 4 Chip conveyor Coolant system 3 height-adjustable machine feet Spindle cooler Control cabinet cooler from Rittal Operating manuals

Condition: good (used), the machine is in good condition, includes electrical cabinets, sharpening machine Redpfx Aevdyr Nem Tscd

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 500 mm, controller model: Heidenhain TNC 410, rotational speed (max.): 10,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range X-axis: 800 mm Travel range Y-axis: 500 mm Travel range Z-axis: 500 mm Spindle speed range: 0–10,000 rpm Spindle speed control: stepless Tool holder: SK 40 Magazine capacity: 20 MACHINE DETAILS Control system: Heidenhain TNC 410 Rcsdpfx Amjzmryyo Ted Clamping area: 1,000 × 500 mm EQUIPMENT Fixed angular table Vertical tool changer Full enclosure with sliding doors and interior lighting Various tool holders SK 40 Electronic handwheel Coolant system with enhanced pump Coolant pressure: 20 bar Chip conveyor Operating manual

Condition: ready for operation (used), Year of construction: 2002, operating hours: 20,377 h, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 500 mm, controller model: Heidenhain iTNC 530, rotational speed (max.): 20,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 800 mm Travel range, Y-axis: 650 mm Travel range, Z-axis: 500 mm Speed range: 0–20,000 rpm Speed control: stepless Magazine capacity: 30 Tool holder: HSK 63 MACHINE DETAILS Control system: Heidenhain iTNC 530 Clamping area: 900 × 600 mm Operating hours Machine operating hours: 54,796 h Spindle operating hours: 23,462 h Program run time: 20,377 h EQUIPMENT Fixed tilting table Vertical tool changer Rcedpfx Amezmrpuo Ted Full enclosure with sliding doors and interior lighting Electronic handwheel Tool measurement in the working area with BLUM laser 3D infrared probe Renishaw Chip conveyor Coolant system 4 height-adjustable machine feet Operating manuals

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SF100s.01.26, screw diameter: 200 mm, total length: 3,200 mm, total height: 2,200 mm, overall weight: 400 kg, heating capacity: 10 kW (13.60 HP), pressure: 2 bar, type of input current: three-phase, input frequency: 50 Hz, input voltage: 380 V, warranty duration: 24 months, Machine for cheese streching, dozing, mozarella and other. Rcjdpjt I Dxwefx Am Tjd

Condition: ready for operation (used), Year of construction: 1991, functionality: limited functionality, travel distance X-axis: 5,020 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 2,000 mm, spindle diameter: 100 mm, controller model: Heidenhain 415 B, TECHNICAL DETAILS Spindle diameter: 100 mm Travel in X-axis: 5,020 mm Travel in Y-axis: 1,000 mm Travel in Z-axis: 2,000 mm Tool holder: SK 50 MACHINE DETAILS Control system: Heidenhain 415 B Rotary table dimensions: 2,500 x 2,000 mm EQUIPMENT Indexable milling head 2.5 60-position tool changer Rotary table manufacturer: Scharmann Redpfx Aezlryqjm Tocd Note: The rotary function of the rotary table is defective. The machine is sold without pallet changers.