High speed edger 35-55 board/min

MADREW AE-400

Condition: excellent (used), Storti RM 500 edger - Italian production - year of production 1993 - electric spacing of discs TECHNICAL PARAMETERS: - cutting width max 435 mm - cutting height max 170 mm - engine power 2 x 22kW - max element width 600 mm - minimum material length 800 mm Nlsdpfsk Talpex Anfoa - max disc diameter 600 mm - spindle diameter 40 mm - two upper pulling rollers - one upper pressure roller - roller motor power 2 x 1.1 kW - roller pressure with automatic jump - seven bottom pulling toothed rollers - electric disc adjustment - two lasers - feed speed 25 and 50 m/min - feeding table 2950 mm - receiving table 3000 mm - drive rollers D100 mm - power of the roller feed motor 2 x 1.5 kW Transport dimensions 500x240x180 cm weight 3500 kg

Condition: new, Year of construction: 2023, Application combs 10 mm Nlodpfx Aoiacbpjnfea Application combs 15 mm Application combs 20 mm finger joint profile 15 mm finger joint profile 20 mm delivery time 3 days

Year of construction: 1998, condition: excellent (used), functionality: fully functional, Very stable creel roller conveyor with hydraulic lift and lowering cross conveyor. Njdpfx Aet Hg Husnfsla 1st part: Length 7,100 mm. Roller length 2,000 mm. Roller diameter 220 mm. Overall height 1,000 mm. Built-in hydraulic lifting and lowering cross conveyor With 4 chain strands. Spacing: 1,500 - 1,300 - 1,000 mm. Fully plated. Hydraulic model support rollers. Drive via geared motor. New bearings. 2nd part: Length 7,200 mm. Roller length 1,600 mm. Conveyor length 6,100 mm. Built-in hydraulic lifting and lowering cross conveyor with 6 chain strands. Unsupported, it is possible to convey the cut material under the roller conveyor to the left or right. Fully plated. Including hydraulic unit for both roller conveyors.

Year of construction: 2000, condition: excellent (used), Span approx. 20,0 m Lifting height approx. 8,0 m Make/reconstruction HILGERS/TEICHMANN Modification/New construction 2000/2021 Crane equipped with: - Double-rail trolley with 4-corner rope outlet Njdpfeqfc Egjx Anfela - Magnet System prepared - Radio remote control - Optionally with magnetic traverse or spreader

Condition: used, Year of construction: 1989, functionality: fully functional, Used dip installation, manufacturer Bachhäubl HS2 12.5 - 12.50 m long x 1.50 m wide x 1.50 m high, clear internal dimensions; - Year of manufacture: 1989; - Control unit with timer relay for setting immersion time. - Wooden support with frame approx. 7 m long, hold-down device with 7 prongs, approx. 7 m long; - Basin interior in good condition, - single-walled, without collection tray! - Weight approx. 8.5 tons - Transport dimensions approx. 13.00 x 2.35 x 2.80 m Nodpfxjx Aktwo Anfola - Installation is supplied without impregnation agent and without sludge, - free loaded on truck!

Condition: refurbished (used), Completely refurbished Bongioanni CRL 4 tensioning wagon with clamping blocks. Track gauge 1200 mm. Rails newly milled. Servo-electric drive. Sale upon customer order. Nlodpfx Anjxtwxbsfja

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Nsdpfswp Rqfex Anfjla Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: ready for operation (used), Logintake with butt end reducer and debarker. Nedpjtrd Hfefx Anfela Below parts included: - Log deck with log unscrambler and log singulator - Butt-end reducer type Bruks RR1000 - Debarker type cambio 70-66 - Out-feed log conveyor with logkicker

Condition: new, Year of construction: 2025, The automatic stacker is suitable for stacking boards of different lengths in layers. The stacker automatically adjusts to the board length to be stacked. Nlodpfshbr Tpex Anfja The desired stacking height can also be preset. The power consumption of this machine is only 12 kW. ARBOR designs and manufactures stackers individually - according to your production parameters. . . . . . . . . . . . . . . . ARBOR manufactures equipment of varying complexity for woodworking enterprises.

Condition: used, Year of construction: 1997, - edge banding unit - Cross-cutting unit - Milling unit - Fine trimming unit Nlsdpfxod Inktj Anfsa - scraper - buffing unit