Multisaw

MRS 350

Condition: new, Year of construction: 2022, New machine Year of manufacture: 2022 Standard Equipment: - Electrically powered height and tilt adjustment (0–46°) with automatic correction of cutting height during tilting - Eye-level, swiveling control panel - Double roller carriage, carriage length 3,000 mm - Manually adjustable rip fence with scale, including manual fine adjustment, max cutting width 1,000 mm - Crosscut fence with fixed 90° position, manually adjustable via scale up to 3,200 mm - Max saw blade projection: 150 mm - Max saw blade diameter: 450 mm - Drive power: 4 kW (5.5 HP) at 4,000 rpm - AKE main saw blade clamping system - Working height: 91 cm Motor 5.5 kW (7.5 HP) with VARIO F45: - Stepless speed control from 2,000–6,000 rpm - Precise speed adjustment to the material increases cutting quality and blade service life Extended Cutting Height for Single-Side Tilting: - This option enables single-side tilting with a large extraction hood for max blade Ø 550 mm and a blade projection of up to 204 mm - In combination with a scoring unit: max blade Ø 500 mm / max cutting height 179 mm - Only available in conjunction with at least 5.5 kW (7.5 HP) drive power 2-axis Scoring Unit for Tilting: - With motorized height and lateral adjustment, programmable scoring blade height with quick lowering and raising Rsdpfxjw I Uxcs Aaasr - Drive motor 0.75 kW (1 HP), 8,200 rpm - Retrofitting only possible on machines prepared for the scoring unit LED Lighting: - Highly energy-efficient LED technology for clear marking of the scoring area The Altendorf double roller carriage is renowned for its smooth operation and precision run. It can be locked steplessly in any position. The large double rollers, precision-manufactured from hardened steel, ensure the upper carriage remains absolutely accurate in conjunction with the lower carriage on the hard-chromed guide bars. This running quality is maintained even after decades of heavy use and exposure to dirt. The carriage construction features a highly rigid, torsion-resistant multi-chamber design. The table surface is finely planed and anodized. A hard-chromed round bar in the upper carriage serves as both the mount for the cross-slide and the interface for various accessories. The entire unit is low-maintenance and does not require lubrication. On/Off Switch on Double Roller Carriage: - The on/off switch on the double roller carriage is always within easy reach. With four buttons, both the main saw blade and the scorer can be switched on and off, saving time and increasing safety. Angle/Mitre Fence, Crosscutting up to 3,500 mm: - This Altendorf-patented fence with integrated length compensation makes it easier to cut angles and mitres precisely in a single operation. In both positions, the swivel angle is steplessly adjustable by up to 49° and displayed on a scale. The play-free and robust stop flaps can easily be moved and adjusted as a single flap over the entire area up to max. 3,500 mm.

Condition: new, Best price 4499 Eur (EXW Jonava, Lithuania) Dimension of sliding table- 2200x375mm Gross cut capacity- 1500mm Width of cut between saw blade and rip fence - 1140mm Saw blade diameter - 400mm Height of cut (90°) - 115mm Height of cut (45°)- 105mm Speed of main saw spindle - 4500/6000rpm Main spindle diameter - 30mm Tilting saw blade - 0-45º Saws lifting, up and down, electrical control. Main motor - 5,5 kW Scoring saw blade diameter - 120mm Speed of scoring saw blade - 7000-8000rpm Scoring saw diameter - 20mm Scoring motor - 1,1 kW Weight: 700 kg * Using the blade 400mm, the smaller should be removed. Rjdsdnxydopfx Aaajr Reduced saw blade should be used with not more than 350 mm main shield.

Condition: excellent (used), Year of construction: 2018, working size (mm) 400X300mm Distance from saw blade to worktable (mm) 3~200mm Conveyor belt width (mm) 385mm Saw wheel power (kw) 18.5kw Saw unit sprocket diameter (mm) 711mm Feeding speed (m/min) 0~12m/min Hydraulic pressure (kg/cm²) 55kg/cm² Redpfx Asi Ay Hqeaaor Dust outlet diameter 102mmX2 Blade size (L x W x H) (mm) 4572 x 27 x 0.9mm Saw Gap (mm) 1.5~1.8mm Overall dimensions (LxWxH) (mm) 3000x2250x2000 Net weight (kg) 2100kg

Year of construction: 2010, condition: excellent (used), functionality: fully functional, Usable cutting length 5000 mm Rjdoyg Epvopfx Aaajr Blade diameter 550 mm Electronic head tilting Internal/external inclination from 22°30′ to 135 ° Measuring probe

Year of construction: 1999, condition: excellent (used), 1999 Start type: to be agreed Cost of delivery: Customer cover Conditions of delivery: OWN RECEIPT Category: Grinding machines in Poland Subcategory: Through grinding machines Subcategory 2: Grinding machines, brushing machines Description Manufacturer VANGROENWEGHE Model / type of TYPE M-300-COMBI / CE machine Redped Nmdksfx Aaajr

Condition: good (used), Year of construction: 2012, functionality: fully functional, CNC machining center with edge banding for shaped workpieces Working dimensions for Y1 axis: X axis: 4,300 mm X axis pendulum operation: 1,620 mm Y axis: 1,320 mm Working dimensions for Y2 axis (edge processing): X axis: 3,300 mm X axis pendulum operation: 600 mm Y axis: 1,240 mm Work table: 8 ATS workpiece supports with 3 vacuum cups each 8 rear workpiece stops, program-controlled lowering, each mounted in one support Rjdpfx Asxraimeaasr 8 workpiece stops, 670 mm from rear, each mounted in one support 2 + 2 lateral workpiece stops 4 removable center stops 6 lift rails, pneumatically program-controlled lowering, for positioning heavy workpieces Automatic positioning of workpiece supports and vacuum cups via EPS (Electronic Positioning System) Automatic central lubrication Vacuum system divided into 2 separate work zones along the X axis Vacuum assist system for clamping templates Chip conveyor integrated into the machine table Vacuum pump 90 cbm/h Processing head equipment: Mounted on Z2 axis Drilling head BH 26 2L with: 16 vertical drilling spindles, individually selectable 2+2 horizontal drilling spindles in X direction 2+2 horizontal drilling spindles in Y direction Grooving saw, diameter 120 mm, fixed in X direction Grooving saw, diameter 120 mm, fixed in Y direction Milling spindle 13.2 kW (11 kW in S1 operation), HSK 63 F Mounted on Z1 axis Speed range 1,000 – 24,000 rpm Clockwise and counter-clockwise rotation C axis 360 degrees for adapter units Cleaning nozzle for cleaning the milled edge before the edge banding process Tool magazine for 16 tools Edge banding unit for workpieces up to 60 mm thickness Edge banding unit CNC controlled, with 360 degree endless rotation Glue application for hotmelt adhesive Double pressure roller, interchangeable and can be switched off Heating lamp for preheating edge band material End trim unit to cut the edge band material at an 8-degree angle to the workpiece edge using circular saw blade Technical data: Plastic edge thickness 0.4 – 3 mm (*) Solid wood edge thickness 0.4 – 2 mm (*) (Best results achieved using wood edges with primer from 0.4 – 1.2 mm) Max. edge height 64 mm Panel thickness min. 14 mm, max. 60 mm Min. inside radius 18 mm for edge thickness less than 1 mm Min. inside radius 30 mm for edge thickness 2 mm Min. panel size for edge banding: 300 x 300 mm Min. size for edge banding of internal cutouts: 350 mm, with plastic edge max. 1 mm thickness and max. panel thickness 18 mm Edge magazine for 2 rolls, positioned outside the machine—this solution limits pendulum processing. Roll diameter for edge material: 800 mm Safety equipment: * Safety mats in front of the machine * Safety fence on the right with access door Without tools Control system: PC control with BIESSE WORKS ADVANCED Restart after emergency stop BIESSE WORKS office version Units: - Flush/radius trimming unit - Combination profile/flat scraper unit - Sawing unit

Condition: used, Year of construction: 2015, Numerical Control NC 1000 Software Biesse Works Working field in X axis 4300 mm Working field in Y axis 2205 mm FT nesting full plane worktable Automatic loading system with side lifting table Automatic labeling machine for barcode printing Automatic printing and application system of adhesive labels N ° 1 vertical electrospindle, with automatic tool change, HSK F63 Blade unit integrated in the drilling head on X axis - diam. 120 mm Blade unit integrated in the drilling head on Y axis - diam. 120 mm Automatic tool change system with 8 positions - positioned on the machine operating head Automatic tool change system with 21 positions - positioned on the rear of the machine with chain BH 20 boring head with independent spindles arranged as follows: - N ° 8 vertical in X axis - N ° 8 vertical in Y axis - N ° 4 horizontal in X axis - N ° 4 horizontal in Y axis Automatic unloading system with motorized belt Front protection and safety system with carpets and perimeter nets Automatic lubrication system Air conditioning system for the electrical panel Vacuum pumps Rodswt Snyspfx Aaasr

Condition: like new (used), Year of construction: 2025, operating hours: 2,000 h, functionality: fully functional, machine/vehicle number: 1630, overall weight: 7,800 kg, warranty duration: 6 months, power: 85 kW (115.57 HP), Complete production line for sale, based on a Di Più BRIK MB100 briquetting press (complete production line). Fully refurbished DI PIU BRIK MB100 machine (factory-refurbished in 2025), ready for immediate operation. The machine is designed for high-capacity briquetting and is suitable for demanding industrial applications. The machine has approximately 2,000 operating hours. It has been newly refurbished at the Di Più factory: all vital components have been replaced, including all cables, electrical wiring, and required electrical equipment. The machine is brought to as-new condition and comes with a 6-month Di Più factory warranty. The machine can produce briquettes with or without a hole, with a diameter of 90mm to 110mm, using soft or hard wood, in either round or square shapes. Machine inspection is possible at the factory in Italy: Di Più Systems Srl, Via dell’Innovazione 11, 36042 Breganze (VI), Italy. The Di Più BRIK MB100 mechanical briquetting press is an automatic machine for compacting wood, sawdust, and other waste materials into wooden briquettes. The ideal humidity of the input material is between 8% and 12%, and the particle size between 1mm and 12mm. Technical data: Redswrp Emepfx Aaasr - Production capacity: 1,300 – 2,300 kg/h (for sawdust density 160–200 kg/m³) - Briquette diameter: 90 – 110 mm - Main motor power: 75 kW - Total installed power: 98 kW - Piston compression pressure: 2,000 – 2,500 kg/cm² - Vertical screw with gearbox: 5.5 kW - Oil pump: 1.5 kW - Oil pump for extruder head closure: 1.5 kW - Feeder with screw and adjustable speed: 1.5 kW - Oil system for bronze bearing lubrication: 100 liters - Briquette output monitoring sensor (automatic shutdown when material supply runs out) - Safety covers for moving parts - Oil pressure sensor - Control cabinet - Input material storage hopper (buffer) - Level sensor for feed system monitoring - Machine weight: approx. 7,800 kg The machine is equipped with all necessary accessories for complete operation and integration into a briquetting line: ACCESSORIES – MB100: - Dosing silo: Made of heavy-duty steel. Diameter: 1,500 mm, height: 1,000 mm. Equipped with a rotary cutter with 2.2 kW gearbox, mounted on a robust steel frame. Material supply is monitored by a level sensor. - Briquette cooling line after extrusion, total length 20 meters - Automatic briquette cutting saw - The saw automatically cuts briquettes to the operator's preset lengths - Device for producing briquettes with a hole - Machine head cooling system with ice water - The system produces 50 liters/min of ice water for effective briquetting head cooling. - Air-cooled water chiller with hermetic scroll compressors, microprocessor control, and a large energy storage tank with an immersed water-to-refrigerant heat exchanger. - The heat exchanger is a high-efficiency fin-pack type, made of copper pipes and aluminum fins. - Water tank with a capacity of 800 liters - Water feed pump (50 l/min – 20 m.w.c. – 0.55 kW) with three-circuit DN25 valves for regulating cooling water temperature at the briquetting head - Digital electronic temperature controller connected to an NTC sensor (measuring element d.6 × 52 mm, IP68, AISI 316) OPTIONAL: NOVAPAC packaging machine Possibility to purchase an additional NOVAPAC packaging machine, fully compatible with the Di Più BRIK MB100 and other machines. An ideal solution for automatic packaging immediately after briquetting. Year: 2013 Price for Novapac: €19,000 Equipment visible in the las

Condition: new, Year of construction: 2025, The automatic stacker is suitable for stacking boards of different lengths in layers. The stacker automatically adjusts to the board length to be stacked. The desired stacking height can also be preset. The power consumption of this machine is only 12 kW. ARBOR designs and manufactures stackers individually - according to your production parameters. . . . . . . . . . . . . . . . ARBOR manufactures equipment of varying complexity for woodworking enterprises. Rsdpfohbr Tpsx Aaasr

Condition: not inspected (used), Year of construction: 1991, Torwegge multirip saw Chain width 250mm cutting height 100mm Total connection 39kW Redpfxjucnukj Aaajr