Used Automatic Edge Bander for sale (24,909)

Condition: used, mileage: 391,403 km, power: 221 kW (300.48 HP), first registration: 04/2013, fuel type: diesel, tire size: 315/70, tire condition: 40 %, axle configuration: 4x2, fuel: diesel, color: other, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, Year of construction: 2013, Tyre size: 315/70 Tyre profile: 40% Front axle: Steering Iodpfxszux Itj Aggsba Rear axle: Double wheels

Condition: used, Year of construction: 1991, saw blade diameter 275 mm cutting diameter 90 mm cutting speed 80 m/min EISELE Miter Circular Saw VMS 120 Isdsx Avtvopfx Aggeba Saw blade diameter: 275 mm Cutting capacity at 90° (round): 90 mm Cutting capacity at 90° (rectangular): 75 × 75 mm Cutting capacity at 45° miter (rectangular): 75 × 75 mm Saw blade speed: 40 / 80 rpm Drive motor: 380 V, 1 / 1.2 kW Required floor space: 700 × 600 × 1580 mm Weight: approx. 180 kg

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Ibsdszuzw Dopfx Aggsa Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2021, Painting system for edge surfaces Manufacturer: WIKOMA Painting of narrow edge surfaces Commissioned: 2021 Intended use: Spraying the edges of furniture panels arranged in stacks. Scope of delivery: - 2 spray booths - 2 hot air drying tunnels - 1 sanding booth Ibedpfx Agjzuztxsgsa - Chain conveyor - Control cabinet The system was in operation until the end of June 2025. Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2010, Edge milling machine Manufacturer: Brandt Type: FTK 130 Year of manufacture: 2010 Note: Isdpjzuzlhefx Aggoba The technical data and descriptions are a transcript of the original order confirmation. The data is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2010, Edge banding machine Manufacturer: Brandt Type: Optimat KTD 720 Year of manufacture: 2010 Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding. Iodpfx Agszuzlbegoba

Condition: used, Year of construction: 1987, Edge grinding machine Manufacturer: Rehnen Type: R1 Year of manufacture: approx. 1987 Technical data Work table: 1100 x 500 mm Grinding belt: 2280 x 150 mm 3 kW main motor 6.4 Amps Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding. Ibodozuzddepfx Aggsa

Condition: used, Year of construction: 2017, - 4 belt grinding units - Frequency control for all units - Electronic grinding pressure control Universal edge and profile grinding machine Manufacturer: Heesemann Type: UKP 20 Year of manufacture: 2017 Technical data Workpiece transport system - Total length: 5015 mm - Driven by a 1.5 kW three-phase motor with a double chain for workpiece transport - Feed rate in the range of 5-25 m/min, frequency-controlled - Working height constant at 880 mm - incl. integrated control cabinets - incl. adjustable guide rail with digital display and incl. counter rail with central width adjustment 4 lateral guide rollers between the grinding units for secure transport of workpieces Industrial PC 10.4" - LCD-TFT color display - Touch screen version - with display for production and downtime - with program memory for 100 programs 2 belt grinding units "M 4" Pos. 1 and 2 - for grinding straight edges - Belt dimensions: 2300x80 mm - Belt speed: 0.7-12 m/s - Motor power: 3.0 kW - with electronic frequency control for stepless control of the belt speed - Electronic grinding pressure control from the terminal 2 oscillation units for "M4" (Pos. 1+2) For complete utilization of the grinding belt 2 belt grinding units "K 4" Pos. 3 and 4 - for grinding small profile sections - can also be used for edge breaking Ibodpfx Agszuzb Aegea - Can be swiveled 90 degrees upwards and 45 degrees downwards - Belt tear switch - Tool holder with quick-change device - Intermittent belt extraction device - Belt dimension: 2000x50 mm - Belt speed: 0.5-8 m/s - Motor power: 1.1 kW - with electronic frequency control for stepless control of the belt speed - Electronic grinding pressure control from the terminal 4 electronic control units - for the fully automatic timing of the lowering and raising of the grinding tool, depending on the set feed rate, the grinding pressure and the unit angle setting Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2021, - Working width 1,350 mm - Belt feed speed 2 to 16 m/min - PRO SAND electronic control Automatically Calibrating Sanding Machine Ijdpezuzbcsfx Aggsba Manufacturer: SCM Type: DMC system Year of manufacture: 2021 Technical data - Working width 1,350 mm - Belt feed speed 2 to 16 m/min - PRO SAND electronic control - PLC terminal with 10.4" LCD color display Unit 1 TIE 5000 working unit for additional table, internal cross-padding - Sequencing system of the unit for belt change by only one machine operator - Automatic brake - Linear blower with timed activation for belt cleaning - Belt dimensions: 150 x 5,000 mm - Chevron belt dimensions: 140 x 4,710 mm PE16T EPICS electronic sector sanding, pitch 16 mm - 16 mm distance between sectors from center to center - Double-acting pneumatic cylinders with adjustable feed/counter feed - Graphite cloth with quick extraction device - Complete management of functions via the electronic Pro Sand control - Motor with inverter power up to 15 kW Unit 2 DO19 orbital unit for 19 rotating disc brushes - Manual adjustment of the unit's working position - 1.1 kW main motor with inverter drive - Independent motor for controlling the orbital movement - Diameter of the rotating disc: 125 mm FT/19/125 Set with 19 rotating discs, diameter 125 mm Unit 3 BF300 working unit for brush roller, diameter 300 mm - Manual adjustment of the roller's working position - 4 kW main motor with inverter drive FT 300 brush roller, diameter 300 mm Unit 4 BF300 working unit for brush roller, diameter 300 mm - Manual adjustment of the roller's working position - 4 kW main motor with inverter drive FT 300 brush roller, diameter 300 mm Unit 5 SC 2620 working unit for super finish pad - Rotation of the belt in the opposite direction of the conveyor belt - Electronic belt swiveling control - Disc brake - Chevron belt dimensions: 1,370 x 2,186 mm - Belt dimensions: 1,370 x 2,620 mm PE16/C EPICS electronic sanding block with sector pitch 16 mm - 16 mm distance between sectors from center to center - Double-acting pneumatic cylinders with adjustable feed/counter feed - Graphite cloth with quick extraction device - Complete management of functions via the electronic Pro Sand control - Inverter motor with a power of up to 15 kW Inverter-controlled vacuum motor integrated into the machine frame, up to 7.5 kW - Rubber-coated conveyor belt, 50 Shore - 4 kW conveyor belt motor with inverter drive Console with integrated PC eye-M and electronic Maestro Pro Sand control with tele service system Device connected to the machine that enables the use of the Maestro Pro Sand software. The integrated LED light strip enables the operator to monitor the machine's status in real time (emergency, operation, etc.) without having to be near the machine itself. It is equipped with a fanless industrial PC with protection class IP53 (IP65 on the front). This robust solution guarantees the highest level of resistance even under the most adverse environmental conditions that an industrial site can offer. The 21.5" LCD color display with a large 16/9 touchscreen enables particularly easy and efficient control of the machine's most important functions: - Full HD display resolution 1920x1080 - LED backlight - Capacitive

Condition: used, Year of construction: 2010, - Release agent application, top and bottom - Scoring saw with 2.2 kW motor - Trimming unit with 8.0 kW motor - Double milling unit with 2 motors, each 4.5 kW - Gluing unit - End trimming unit - Flush trimming unit - Multi-function unit - Multi-profile edge trimming unit - Spray nozzles, top and bottom - Flat edge trimming unit - Buffing unit - Grooving unit Double-sided edge banding machine Manufacturer: IMA Type: Combima/II/390/B/L12 Year of manufacture: 2010 Ijdpfx Agezuyqisgjba For longitudinal and transverse feed - 2 low-maintenance precision roller chains with 75 mm wide and 85 mm long, rubber-coated chain plates, with cams - Spacing 1080 mm. Pneumatically adjustable to heights of 8, 16 or 24 mm. ICOS OPEN control system - Max. feed width 3,300 mm - Program-controlled master + slave width adjustment - Fixed stop on the left in feed direction Workpiece dimensions - Min. feed width 244 mm (for longitudinal processing) - Max. workpiece width (chain extension) 1,300 mm - Min. workpiece thickness 8 mm - Max. workpiece thickness 45 mm (with copying function) / 60 mm (without copying) Edge material: - Min. height 14 mm, max. height 65 mm - Roll material min. thickness 0.3 mm, max. thickness 3 mm Strips and edgebanding: - Min. thickness 0.8 mm, max. thickness 12 mm Feed speed - 10 - 50 m/min. with frequency-controlled drive. Infeed device - with 5 top-mounted, inclined and driven rollers. Center support with roller track - automatically lowerable and automatically centering. Equipped on each side with: Release agent application, top and bottom Scoring saw with 2.2 kW motor, 100 Hz, 6,000 RPM, pneumatically controlled. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Trimming unit with 8.0 kW motor, 100 Hz, 6,000 RPM. - Electronic positioning for stepless horizontal adjustment. Double milling unit with 2 motors, each 4.5 kW, 150 Hz, 9,000 RPM. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Gluing unit for hot melt adhesive - With single roll/edgebanding magazine for roll material up to 3 mm and edgebanding up to 12 mm - 2-fold roll magazine for roll materials up to 3 mm (can be attached to the single roll magazine) - Horizontal roll holder End trimming unit - Mounted on the upper pressure beam, with 2 motors, each 660 W, 200 Hz - Pneumatic swivel 0 + 25 for straight and miter cuts. - Automatic adjustment for miter cuts with two different edge thicknesses (e.g. 0.4 and 1.2 mm) and for "edge overhang" for copying with edge thickness 1.0 - 3.0 mm. Automatic adjustment to the feed speed 20+30 m/min. Flush trimming unit 08.0555 - With 2 motors 1,850 W, 200 Hz, 12,000 RPM. Multi-function unit 08.353 - NC controlled with 2 motors, with automatic tooling for 4 profiles. Multi-profile edge trimming unit - with automatic tooling for 4 profiles via fixed-point control Spray nozzles, top and bottom - for applying cleaning agents Flat edge trimming unit Buffing unit - With 2 motors, each 180 W, 50 Hz, 1400 RPM. 1 Grooving unit - With 4.5 kW motor, 150 Hz, 9,000 RPM. - Horizontal and vertical adjustment manually with mechanical digital display - Pneumatic activation control - Manual swivel 90 ICOS open - PC-based control system with integrated PLC and electronic path control. - User-friendly interface with Windows standards - Simple, component-oriented

Condition: used, Year of construction: 2010, - Application of release agent, top/bottom - Joint milling unit - Gluing unit - Trimming unit - Copy milling unit SKF-L - Profile trimming blade unit - Spray cleaning agent - Self-adjusting trimming blade unit - Buffing unit Single-sided edge banding machine Manufacturer: IMA Type: Advantage 310 Year of construction: 2010 Technical data Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65* / 150 mm *at a max. workpiece thickness of 25 mm - Workpiece thickness: min. 8 mm, 12 mm with profile trimming blades max. 40 mm (with MFA 08.346), 60 mm (with SKF) - Smallest workpiece: 65 x 300 / 150 x 150 x 19 mm - Machining allowance per workpiece edge: 0 - 5 mm (observe max. chip cross-section) - Workpiece shape: right-angled - Material: chipboard, MDF - Surface material: direct coating (melamine resin paper), paper, film, veneer Edge material - Roll material without film: Paper edges & plastic edges: 0.3 - 3.0 mm Veneer edges: 0.5 - 3.0 mm - max. edge cross-section: 150 - 180 mm² - Cut edge strips: Strips: 3.0 - 8.0 mm - max. strip cross-section: 520 mm² - Edge height: min. 12 mm, max. 65 mm - max. upper edge overhang: 2 mm - Edge profiles Paper edge: approx. 0.4 mm, chamfer 15 Plastic edge up to 3.0 mm, radius depending on the tool Strip up to 8 mm flush milling (with interchangeable motor on MFA) Machine - Constant workpiece projection from the chain track: 35 mm + edge thickness - max. trimming cross-section 520 mm² - Throughput width: min. 65 mm (with projection of 35 mm) - min. workpiece length in feed direction: 150 mm - Overall height (top edge of chain track): 940 mm - Unit side: on the left in feed direction - Pneumatic connection: approx. 7 - 8 bar Application of release agent, top/bottom Joint milling unit 08.379 and blowing nozzle - with 2 motors, each 4 kW, 9000 RPM, 150 Hz Gluing unit 283.1513 with oil bath gearbox - Adhesive output 0.8 l, 60 mm high, with quick-lock system - can be used for hot melt adhesive or PU adhesive - with single roll / strip magazine, roll diameter 800 mm - with 3 main pressure rollers and 3 counter pressure rollers Trimming unit 08.415 - pneumatically swiveling to 0 or 8 degrees - with 2 motors 660 kW, 400 V, 200 Hz, 12000 RPM - 2 HM trimming saw blades 160 x 3.5 x 22, Z=36 Copy milling unit SKF-L Ibsdjzuyp Espfx Aggea - with 2 motors 180 W, 400 V, 200 Hz, 12000 RPM - and 2 motors 400 W, 400 V, 200 Hz, 12000 RPM - 1 set of DP profile milling cutter I 80x12xHSK25-R, Z = 4, with HSK25 shank - Profile length in the feed direction: max. approx. 50 mm - Workpiece thickness: max. 60 mm - Working speed: max. approx. 20 m/min - Distance between 2 workpieces: min. approx. 400 mm - min. workpiece projection = 35 mm + profile depth Profile trimming blade unit 08.519 - For finishing a top and bottom milled quarter-circle profile Spray cleaning agent Self-adjusting trimming blade unit 08.521 - for removing hot melt adhesive residue from the edge area of the top and bottom of the workpiece Buffing unit 08.617-2 - with an upper and lower motor: 180 W, 50 Hz, 1400 RPM - 2 polishing pads 50 x 160 x 19 mm

Condition: used, Year of construction: 1996, - Double-sided IMA COMBIMA for longitudinal machining - Swiveling device Ibjdpfjzuypxjx Aggoa - Double-sided IMA COMBIMA for transverse machining 1 used edge processing line IMA COMBIMA / K/ II/ R75 / 1075 / V / R3 Year of manufacture: 1996 Consisting of: - Double-sided IMA COMBIMA for longitudinal machining: Double edging unit 2 x milling units Gluing unit with granular pre-melting device 6-position roller magazine for edge material 1 x main pressure roller and 4 x follow-up pressure rollers Cutting unit Flush trimming 2 x fine milling units Profile trimming blade Surface trimming blade Buffing unit Smoothing unit - Swiveling device from longitudinal to transverse - Double-sided IMA COMBIMA for transverse machining Protective milling Double edging Grooving milling unit Gluing unit with granular pre-melting device 6-position roller magazine for edge material 1 x main pressure roller and 4 x follow-up pressure rollers Capping at the top pressure (retrofit to current model) Flush trimming Fine milling 2 x MFA milling units Grooving milling unit Profile trimming blade Surface trimming blade Copy buffing (4 motors) Buffing (2 motors) Smoothing unit Note: The technical data and descriptions are a transcript of the order confirmation at the time. Data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, - Edge material thickness: 0.3 - 3.0 mm Ijdpjzuyprofx Aggeba - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm Single-sided edge banding machine Manufacturer: IMA Type: Novimat Contour/I/G80/790/L20 Year of manufacture: 2009 Technical data - Electronically controlled feed speed: 6-30 m/min - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm - Maximum edge overhang from above: up to 8 mm edge thickness - 5 mm, over 8 mm - 2 mm Workpiece size: - Minimum workpiece length in the feed direction: 150 mm - Minimum workpiece width: 25 mm, thickness: 65 mm - Minimum workpiece thickness: 8 mm (without profile trimming blades) or 12 mm with profile trimming blades - Maximum workpiece thickness: without corner copying, max. 60 mm (max. 40 mm with corner copying) - Smallest element: 150 mm x 150 mm or 65 mm x 300 mm Note: *65 mm with a maximum piece thickness of 25 mm The edge banding machine is equipped with: - Hand-adjustable guide rail for inserting workpieces - Trimming units 08.376, 2 motors, each with 4.5 kW, spindle speed 9000 rpm, 150 Hz - Heating unit for warming the workpieces - Gluing unit with drive 283.1513, featuring a tightly sealed oil pan, drive arranged with glue pot content of 0.8 l and glue application height of 60 mm, with a pneumatic quick-clamping system for hot melt and PU adhesives, magazine for edge banding rollers and strips, edge banding roller diameter 800 mm - Glue pellet preheating unit with automatic feeding of glue pellets from a 30 kg container. - Automatic preheating unit for PU cartridges with a weight of approx. 2.5 kg and a capacity of 8-10 kg/h - Trimming unit 08.42/30/B, pneumatic adjustment of the saw blades from 0 - 25°, 2 motors 660 W, 200 Hz with frequency inverter and braking function - Pre-milling unit 08.055, swiveling up to max. 30° - Multi-chamfering unit 08.342, 2 motors, 660 W, 400 V, 200 Hz, 12000 1/min - Cleaning agent dispenser - Profile trimming blades 08.519 - Surface trimming blade 08.521 for removing excess glue from glue joints - Buffing unit 08.617-2, 2 motors with 180 kW, 50 Hz, 1400 rpm - Groove/milling unit with one motor Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2005, - Automatic infeed table - KFA unit - Return system Used single-sided edge banding machine Manufacturer: IMA Type: Combima Systems / I/R751220/R3 1 single-sided combination machine for trimming, edge gluing and edge finishing of panel-shaped workpieces made of wood and/or wood-based materials. - Automatic infeed table - KFA unit - Return system Technical data "Workpiece": Workpiece length - min.: 238 mm - max.: 2350 mm Workpiece width - min.: 142 mm - max.: 800 mm Workpiece thickness: - min.: 8 - 40 mm Iedpfxjzuyple Aggoba Technical data "Strip" (only for longitudinal processing): Roll material: - Paper edge bands & plastic edge bands: 0.3 - 3.0 mm - Veneer edge bands: 0.5 - 3.0 mm Edge height: - min.: 14 mm - max.: 45 mm Technical data "Machine": Variable workpiece overhang from the chain conveyor (including edge with edge thickness 0.3-3 mm): - min.: 40 mm - max.: 80 mm - PC control ICOS open - Feed speed v=5-25 m/min, frequency-controlled drive - Inclined roller table as infeed section NC infeed system for front and carcass parts - for length and width-independent automatic workpiece feed in single-sided edge processing machines. Only for the production of strip material in the 2nd pass - An additional stop rail, adjustable via NC axis. Double milling unit 08.376: - Controllable - Motor 1 operating in the same direction and motor 2 operating in the opposite direction - Reserve space on the unit carrier for a double trimming unit with electrical pre-installation for 2 x 6.6 kW. - Heater 300 lg, 2x1.5 kW, for preheating the workpiece edge. - Gluing unit 04.1570 system for straight edges and adhesive application to the workpiece. The edge thickness depends on the magazine used and is max. 3 mm. - Adhesive application for workpiece thickness max. 50 mm - 2 pre-melting tanks for PU adhesive - 12-position edge magazine for roll material 0.3-3 mm thick. (8 slots up to 3 mm, 4 slots up to 1.3 mm) Vertical roll holder for 12 rolls: - max. roll diameter 850 mm - max. edge height 45 mm - Trimming unit 08.42, for 2 motors mounted on the upper pressure bar - Pre-milling and milling unit with height sensor - with 1 motor 1000 W - Multi-profile / chamfer unit, with 2 motors 1000 W - Contour milling unit KFA 30 - Multi-profile drawing blade unit - Flat drawing blade 08.517 - Copy edging unit 08.604 - Edging unit 08.617-2 - Double milling stand 75.184, 1050 mm high, both stand sides can be used - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 6000 rpm - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 600 rpm - Motor spindle for the use of the Hydro-Format tool system - Return system, manufacturer Meinert Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2008, Automatic circular saw machine Manufacturer: Kasto Type: KASTOspeed C9 Year of manufacture: 2008 Technical data - For sawing steel and non-ferrous metals - Test machine, used very little. - Cutting direction 90°. - Saw blade diameter 250, 285 and 315 mm. - Cutting range approximately 15-90 mm or 15x15-80x80. - Power of drive motor for saw unit 11 kW (special equipment). This enables cutting speeds of 50-700 m/min, among other things. - 2 separate and independently selectable tanks for minimal lubrication. Accessories: - Angle magazine, loading length 6000 mm. Ibedozuymkjpfx Aggoa - Material trolley with drawbar. - Portal crane, maximum load 1000 kg. - Oil mist extraction system. - Chip conveyor. - Chip tipping container with rollers. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: SCM Type: Olimpic K360 T-ER1 Year of manufacture: 2017 Technical data - Feed speed: 11 m/min - Edge thickness: 0.4 - 6 mm - Control: SCM control panel with display - Board thickness: 8 - 60 mm - Power supply: 400 V / 3~ / 50 Hz, 23 A - Min. workpiece: 140 x 90 mm Units Pre-milling - 2 counter-rotating diamond heads (up to 3 mm removal) EVA gluing unit Pressure zone with driven roller + 2 pressure rollers End trimming unit K-2 (straight / beveled, automatic switching) Flush trimming - flush, radius, chamfer Corner rounding R1/R2 Profile + surface scraper blade Polishing unit Anti-adhesive liquid system (2 liquids), edge roller feed Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding. Ibsdpfx Agszuyk Njgja

Condition: used, Year of construction: 2003, Single-sided edge trimming and gluing machine Manufacturer: IMA Type: AVM/K/I/G80/822/S3R3L20 Year of manufacture: 2003 For milling, edge gluing, and finishing for a standard groove - only for pre-shaped/pre-grooved doors and square-edged doors Left-hand machine (fixed stop on the left). Complete processing in 3 passes 1st pass: Processing of the top surface of the door (transverse processing) 2nd pass: Door long edge 3rd pass: Door long edge During the 2nd and 3rd passes, the protruding transverse edge from the 1st pass is milled off by using a co-rotating/counter-rotating milling process. Double groove gluing is only possible through modifications to the machine and subsequent manual finishing of the edge. Max. door thickness: - Straight edge: approx. 70 mm - Groove gluing: approx. 60 mm Stable machine frame as a support for aggregates and housing for electrical installation. Drive for feed speeds of approx. 5-25 m/min., mechanically infinitely adjustable. (not to be confused with processing speed) Continuous, plastic-coated strip-type conveyor chain, approx. 80 mm wide, with automatic central lubrication. Manually height-adjustable top pressure with a V-belt 80 mm wide and spring-loaded, ball-bearing guide rollers. Machine length approx. 10,900 mm Infeed table at the machine inlet. 1 horizontal, manually adjustable, unheated stop bar 1 joiner milling unit controllable, not swiveling, without sensing with 2 motors, each 3 kW Gluing unit for optional operation of straight edge or softforming gluing, by changing the glue application. Edge material: - Strips: up to 1.3 mm - Roll material: 0.4-3 mm - Solid wood strips: 6 mm Strip length max.: 2550 mm Strip height: 14-80 mm (depending on glue application) with: - Side adjustment by hand for the pneumatically controlled glue application. - Height adjustment by hand -15mm downwards and up to +10mm upwards. 1 bell for the main pressure roller, manually adjustable 1 glue application 0.8L, max. edge height 70mm, straight edge with pneumatic quick-release, Chem-Coat coated, electronic temperature control 1 hot melt glue application 0.8L with quick-release, up to max. 80 mm high edge material, soft edge, Chem-Coat coated, with temperature control and control unit for the strip coating 1 automatic Quickmelt hot melt glue feeder with a heating power of 5.0 kW 1 2-fold magazine only for edge material up to 3.0 mm thick, can be manually attached to the single-roll magazine 1 groove forming pressing unit for pressing the edge material into the groove with: - an activation unit 15 kW for re-activating the edge material for groove forming - a pneumatically controlled forming shoe for the underlapping edge - a pneumatically controlled forming shoe for the entire groove - additional post-pressing rollers for the edge areas in the groove - an electro-pneumatic lateral retraction device for the entire pressing unit 1 horizontal adjustment with mechanical digital display 1 trimming unit for 2 motors mounted on the top pressure for trimming the front and rear edge/strip overhang, for trimming cuts flush or with a bevel. 1 milling unit for 2 motors with height sensing, side sensing, for pre-milling from below and above with 2 motors 1kW, 400V, 200Hz, 12,000 RPM, 30° swiveling 1 milling unit for 2 motors with height sensing, side sensing, Ibjdpfx Agozuykvsgsa for fine milling from below and above with 2 motors 660W, 400V, 200Hz, 12,000 RPM, 30° swiveling Note: The technical data and descriptions are copies of the original order

Condition: used, Year of construction: 2019, Edge banding machine Manufacturer: SCM Type: Minimax E10 Year of manufacture: 2019 Technical data Edge thickness (strip material): 0.4 - 3.0 mm Edge thickness with shear cutter at 80 mm edge height: 0.4 - 1.5 mm Edge thickness with shear cutter at 50 mm edge height: 0.4 - 2.5 mm Edge thickness with shear cutter at 45 mm edge height: 0.4 - 3.0 mm Edge height: 10 - 84 mm Workpiece thickness: 8 - 80 mm Minimum workpiece width: 50 mm Minimum edge length: 210 mm Minimum inner radius (concave) at 0.4 mm edge: 25 mm Minimum outer radius (convex) at 0.4 mm edge: 5 mm Feed speed: 4 / 8 m/min Processing temperature: 140 - 220 °C Edge feed Integrated shear cutter for cutting edge material from the roll. Roll table for holding roll material. Suitable for ABS edges, melamine edges, veneer edges, and other pre-fabricated edge strips. Gluing system Teflon-coated glue tank below the table top. Continuous glue circulation to prevent glue deposits. Iedezuykpjpfx Aggjba Fast heating time of approx. 7 minutes. Standby function with timer. Glue tank capacity: 1.5 liters. Pressure system Motor-driven glue application roller. One free-running pressure roller. Foot pedal for start and stop control of the working cycle. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: Homag Type: Optimat KDF 440 C Year of manufacture: 2017 Technical data Workpiece thickness: 8 - 60 mm Edge material: 0.4 - 8 mm (depending on the equipment) Feed rate: 8 - 18 m/min (stepless) Workpiece length min. approx. 120 mm Workpiece width min. approx. 60 mm Glue application EVA hot melt adhesive, optionally PUR-compatible Glue reservoir Teflon-coated, quick-change system possible Total connected load approx. 15 - 20 kW (depending on the equipment) Compressed air requirement: 6 - 7 bar Machine weight: approx. 3,000 - 3,800 kg Control system: powerControl / powerTouch CE marking Equipment: Joint milling Glue application Pressure zone Cut-off saw unit Milling unit top/bottom Corner rounding unit Scraping blade unit Iodpfszuykcsx Aggoba Edge finishing unit Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2012, Softforming edge banding machine with panel cutting device Manufacturer: Elwood Year of manufacture: 2012 Technical data: - Adhesive application system with slotted nozzle - Compatible with EVA and PUR adhesives - Meler adhesive melting and application system - Electronically controlled adhesive temperature and melting time - Panel thickness: 10-60 mm - 2 profiling milling units - IR heating lamps for material preheating - Spray device for release agent - Pressing zone with heated tower pads (can be replaced with pressing rollers) - Edge band magazine - Front and rear trimming units - Top and bottom flush trimming units for longitudinal edge overhang (2 at the top + 2 at the bottom) - Top and bottom polishing units - Computer control for quick, easy and precise adjustment of the machine's main functions and units Iedezuyi Sopfx Aggsba Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, Edge banding machine Manufacturer: IMA Type: Novimat/I/G80/650/R3 Year of manufacture: 2009 Technical data - Workpiece overhang from the chain conveyor: 38 mm - Feed width: min. 65 mm (with max. workpiece thickness of 25 mm) - Workpiece length in feed direction: 150 mm - Overall height (top edge of chain conveyor): 960 mm - Feed speed: approx. 6 - 30 m/min, electrically adjustable - Machine control system ICOS open compact Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65 mm - Workpiece thickness: 8 - 40 mm (with edge trimming function) / 60 mm (without edge trimming function) - Smallest workpiece: 150 x 150 mm or 65 x 300 mm - Edge material: paper, plastic and veneer - Height: 14 - 65 mm - Roller material thickness: 0.3 - 3.0 mm (veneer edges limited to max. 1.0 mm) - Max. upper edge overhang: 5 mm Units Infeed area - Release agent applicator mounted at the top and bottom, not adjustable Ibsdpfx Aszuyi Eeggoa Edge trimming - 2 motors 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - Motor 1 counter-rotating - Motor 2 co-rotating Gluing unit VTG 3-6 - with one preheating nozzle 300 mm for preheating the workpiece edge - 6-position edge magazine for roller material 0.3 - 3 mm thick. - 1 driven main pressure roller and 4 pressure rollers, with scraper, pneumatically adjustable Glue application - with pneumatic quick-lock system - Chem-Coat coating - electronic temperature control - Volume 0.8 l Pre-melting tank approx. 1 l - Heating power 3 x 400 W - with EVA glue, approx. 7.0 kg/h - with filler-free glue, approx. 5.0 kg/h Cutting unit - 2 motors 660 W, 200 Hz - incl. frequency inverter with braking function - pneumatic pivoting 0+25 for straight and bevel cutting Flush trimming - 2 motors each 1000 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function Multi-profile trimming unit - 2 motors each 660 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function - for trimming 4 profiles - with stepper motor axes for horizontal and vertical positioning Contour trimming unit KFA x30 - 1 motor 500 W, 400 V, 400 Hz, 18000 rpm - Program-controlled conversion for up to 4 profiles - incl. fine positioning for different edge thicknesses Multi-profile scraping blade - Stepper motor axes for horizontal and vertical positioning - Scanning from above and below (max. 4 profiles) - Scanning from the side via pneumatic pressure Spray nozzles at the top and bottom for applying cleaning agents - fixed, not adjustable Surface scraping blade - with height sensing skid - electronically controlled horizontal positioning Buffing unit - 2 lower and 2 upper motors, 180 W, 50 Hz, 1400 rpm - 1st motor pair with cloth-sisal discs 50x160x19 mm - 2nd motor pair with polishing discs 50x160x19 mm - The motors operate in the same direction and are both tilted and pivoted in the feed direction. - Each motor can be individually adjusted vertically 2x NC-controlled grooving - 2 milling motors each 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - one manual 90-degree pivoting device from 180 -270 with co- and counter-rotating function - Horizontal, stepless adjustment with AC servo motor for grooving unit Workpiece return Note: The technical data and descriptions are copies of the order confirmation at the time. The information is for informational purposes only and is non-binding.

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: Biesse Type: Jade 240 Ibedpszuyixefx Aggoa Year of manufacture: 2017 Technical data Note: [b]The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.[/i]

Condition: used, Year of construction: 2010, 1. Edge banding machine Manufacturer: Homag Type: KAL 210 Ambition 2264 Year of manufacture: 2010 Technical data Release agent spraying system Joint milling unit (2 x 4 kW) Glue application A20 (granule/quick-melt system) Pressure zone with driven pressure rollers Miter saw HL84 (2 motors) Flush-/radius-/chamfer milling unit BF10/BF20 Ibsdpezuyilofx Aggja Corner copying unit FK11 (2 motors) Profile drawing blade PN10 Straight drawing blade for glue joint Buffing unit (polishing) Release agent and cleaning agent spraying system at the outfeed Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2006, - Edge milling unit 2 x 2.2 kW - Combi-melt gluing unit - Automatic edge magazine - Trimming unit 2 x 0.8 kW - Flush trimming unit 2 x 0.7 kW - Fine milling unit 2 x 0.3 kW - 2 quick-change sets for fine milling - Automated copy milling unit 2 x 0.37 kW - 2 pull blades - 2 surface pull blades - 5-way spraying system - Fine buffing unit with cloth disc 2 x 0.2 kW Edge banding machine Manufacturer: OTT Type: Twister Technical data: Glue application: Hot-melt adhesive application roller with simultaneous and counter-rotating action Edge thickness: 0.3-10 mm Workpiece thickness: 8-60 mm Workpiece width: 70 mm - Minimum Workpiece length: 150 mm - Minimum Operating pressure: 6 bar Feed power: 3.0 kW Feed speed: 14-20 m/min. Electrical connection: 3 x 400 V, 50 Hz Extraction: at 20 m/s, 1 x 180 mm diameter = 35 m³/min. Air velocity: 20 m/s - Minimum Compressed air consumption: 300 liters/min. (approximate value) Equipment - Machining units: Joining: - 2 x 2.2 kW, n=14600, 250 Hz, two individually controlled spindles. Combi-melt gluing unit: - Top-mounted gluing unit with interchangeable hopper for processing EVA, PUR hot-melt adhesives, or standard cleaning granules, hopper volume 2.5 l Edge magazine: - Automatic edge magazine with optical monitoring for strip edges in fixed lengths Trimming: - 2 x 0.8 kW, n=12000, 200 Hz, automatic pivoting 0 / 5, 2 HM saw blades, 140 x 3.2 x 16 mm, z=34 Flush trimming: - 2 x 0.7 kW, n=12000, 200 Hz, single-sided, with 2 HM reversible blade cutter heads HF70, 70 x 20 x 16 mm, z=4 Fine milling (chamfer 15 / 30 / 45): - 2 x 0.3 kW, n=12000, 200 Hz, double-sided, with 2 HM reversible blade cutter heads HF70, 70 x 20 x 16 mm, z=4 AWSR (radius R2-R5): - 2 quick-change sets for fine milling, 2 x 0.3 kW, with 2 HM reversible blade cutter heads AR73 x 16 x 16 mm, z=3, R2-R5 Copy milling: - Automated copy milling with two separate spindles for machining end faces and longitudinal radii. Motor power: 2 x 0.37 kW, 12000 rpm, Tools: R1 - R3 Pull blade: - 2 HM pull bars, automatically adjustable Surface pull blade: - 2 HM pull bars with fine adjustment PU set: Ibjdpfx Agozuyifegja - 5-way spraying system, 2 x release agents, 1 x lubricant, 2 x cleaning agents, fine buffing unit with cloth disc Edge finishing: - 2 x 0.2 kW, n=2800, 50 Hz, oscillating brushes Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Edge banding machine, single-sided Manufacturer: OTT Type: Pacific V 6-F Year of manufacture: 2000 Technical data: Edge thickness: 0.2 - 6 mm Workpiece thickness: 8 - 42 mm Workpiece width: min. 70 mm Workpiece length: min. 0 mm Feed speed: 12 m/min Electrical connection: 3 x 400 V, 50 Hz Extraction: 2 x 120 mm at 20 m/s Extraction capacity: m³/h Equipment, processing units: Edge trimming 2 x 1.5 kW, 12,000 rpm, 200 Hz two tool-controlled spindles Gluing unit Rapid heating tank with Melt-matic automatic edge magazine with optical monitoring for strip edges in fixed lengths Release agent spraying device Cutting unit 2 x 0.2 kW, 12,000 rpm, 200 Hz automatic pivoting 0 / 3 Flush trimming unit x 0.43 kW, 12,000 rpm, 200 Hz Radius trimming unit R2 - R5 2 x 0.3 kW, 12,000 rpm, 200 Hz 2 quick-change stations for trimming units Corner rounding trimming unit 2 x 0.3 kW, 12,000 rpm, 200 Hz Ibsdpfxjzuyh Us Aggsa Scraper blade 2 x carbide scrapers Smoothing unit 2 x 0.2 kW, 2,800 rpm, 50 Hz Weight: 2,000 kg Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is not binding.