Used Edge Banding Round for sale (9,349)

Condition: used, Year of construction: 2013, HOMAG edge banding line with infeed and outfeed. The machine consists of the following components: Machine configuration: HOMAG edge banding line with infeed and outfeed Infeed table: HOMAG PROFI TBL100/20/25/F FlexLine Edge banding machine: HOMAG PROFI KAL330/7/A3/WZ Panel outfeed: HOMAG ZHR 30/L/125/F TECHNICAL DETAILS Panel length min.: 240 mm Panel length max.: 3,000 mm Panel width min.: 120 mm Panel width max.: 1,200 mm Panel thickness min.: 12 mm Panel thickness max.: 60 mm Edge thickness min.: 0.3 mm Edge thickness max.: 3 mm Gluing system: EVA hot melt Number of processing units: 9 pcs. Number of units in the joining section: 1 pc. Number of units in the edge processing section: 7 pcs. Feed speed max.: 25 m/min Trimming unit Manufacturer / Model: S2 Motor power: 3 kW Dwedpfx Aljz En Axe Sec Speed: 9,000 rpm Automatic cycle adjustment: Yes End trimming unit Manufacturer / Model: HL 84 Number of motors: 2 pcs. Motor power: 0.4 kW Speed: 12,000 rpm Working speed max.: 25 m/min Flush trimming unit, top and bottom Manufacturer / Model: BF10 Number of motors: 2 pcs. Motor power: 0.55 kW Speed: 12,000 rpm Corner rounding unit Manufacturer / Model: FK 11 Number of motors: 2 pcs. Working speed max.: 25 m/min Profiling unit Number of motors: 1 pc. CNC positioning: Yes Automatic cycle adjustment: Yes Edge pulling unit Manufacturer / Model: PN20 Glue application unit Manufacturer / Model: FA 11 Scraping unit Manufacturer / Model: FA 11 Number of motors: 2 pcs. Feed speed, infeed max.: 40 m/min Feed speed, outfeed max.: 25 m/min EQUIPMENT FlexLine infeed table Pressure bar with rubber belt Panel stop Overpressure Edge heating lamps Edge magazine with 24 positions Hot melt glue tank Hot melt pre-melter Edge pressing roller unit with 3 pressure rollers CNC positioning of the pressure rollers Spraying device PowerTouch PC23 machine programming software Panel outfeed via transfer roller conveyor Panel transport via motorized conveyor belt Clamping feed system Panel outfeed system, left CE conformity The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing and use of the machine at the destination. External Reference: 7694

Year of construction: 2023, condition: new, functionality: fully functional, machine/vehicle number: 2230832-269, Barbaric RTS 02 Professional reverse transfer system with destacking, year of manufacture 2023. Workpiece recirculation with 0 - 90 - 180 degree rotation, part measurement, destacking function including stack construction and manual mode for oversized panels. Composed of a removal station RX U4 B2200, conveyor belt L9000 B800, delivery station Comfort, movable table, dual function, steplessly adjustable conveyor belt, support rollers with double track, portal RTS 6100, safety fences and 2 safety light curtains. Largest part 2800 x 1300 mm, smallest 300 x 80 mm, maximum 60 kg. Pick-up with suction cups, up to 12 cycles per minute, transfer speed up to 120 m/min, stacking height 800 mm. Connection 400 V / 50 Hz, 20 A and compressed air 0.6 MPa. Dwedpfxoz Ngg Ee Al Soc

Condition: used, Year of construction: 2015, machine/vehicle number: MR007049, Used: SCM edge banding machine, in very good condition. Complete machine, ready for immediate use. Used: Edge banding machine, manufactured by SCM – model Olimpic K360 T-ER13 Equipped with the following options: - Machine complies with European CE standards Djdpfx Alozgwzvs Sswc - Anti-adhesion spray unit AAR - Glue scraper unit RC-V - Brush unit SP-V - Touch 7 control – 7'' touchscreen control (including the ability to store up to 60 programs) - AUTOSET for T-ER1 3 positions for R-K flush-trimming unit 2 positions for round-over unit pneumatic on/off switching of the glue scraper unit - Nesting sensors for the machining units The machine is equipped with the following units: – Pre-milling unit with 2 motors – with compressed air cleaning after milling – Spray unit, sprays after pre-milling, to prevent adhesion of the glue to the surface. – Glue unit, with dual temperature setting for selecting, for example, PU and EVA glue. – Trimming unit for cutting off the edge band. – Milling unit with solid guide rollers, for a perfect milling operation along the surface. – Round-over unit, for milling rounded edges or bevels. – Radius scraper unit for a perfectly smooth finish (R=2). – Spray unit, for dissolving the glue and applying a sheen. – Glue scraper unit, for removing glue residues on the surface. – Brush unit for polishing the glued edge. Technical specifications: - Min./max. band thickness: 0.3-3 mm - Feed speeds: 11 m/min - Minimum panel thickness: 8 mm - Maximum panel thickness: 50 mm - Weight: 1433 kg - Serial number: AH/118707

Condition: excellent (used), Year of construction: 2017, machine/vehicle number: 138/1-703 15509125, functionality: fully functional, input voltage: 400 V, input current: 18 A, input frequency: 50 Hz, edge thickness (max.): 15 mm, height adjustment type: electric, actuation type: electric, total height: 2,230 mm, total length: 8,755 mm, total width: 2,416 mm, overall weight: 4,200 kg, Edge banding machine (for laminated boards): Year of manufacture: 2017 Type: LUMINA 1586 PREMIUM Serial number: 138/1-703 15509125 Control system: HOL-HER EDGECONTROL TOUCH PPC 319 Gluing technology used: EVA glue granules GlueJet (exchangeable station), L-Tronic laser (exchangeable station) Units: pre-milling cutters, gluing station, pressure unit, trimming saw (two motors, with pneumatic angle adjustment), milling units (for straight and radius edges), rounding units (2 motors, digitally adjustable), sanding units (profiled and flat), indexing unit (NC axes), polishing unit Workpiece thickness: 8 mm – 60 mm Minimum workpiece width: 150 mm Maximum edge banding thickness: 15 mm Maximum edge banding thickness in roll form: 3 mm Maximum edge banding height: 64 mm Machine length: 8.755 m Width with retracted roller support: 1830 mm Width with extended roller support: 2416 mm Minimum height: 1814 mm Maximum height: 2230 mm Workpiece inlet height: 877 mm Machine weight: 4200 kg Minimum electrical connection power: AC 400 V 50 Hz + N … 18A Dodpfsz I R Snex Al Sowc Compressed air, working pressure: 6 bar Compressed air, maximum pressure: 8 bar Chip extraction, connections: 2x Fi 120 mm, 2x Fi 140 mm Zero joint: infrared Electrical height adjustment: YES Top belt pressure: YES Maximum feed rate: 25 m/min Feed rate adjustment, stepless: YES Heating zone: YES Spray nozzles: YES Machine documentation: YES Complies with all relevant provisions of the following EC directives: Machinery Directive 2006/42/EC, Electromagnetic Compatibility Directive 2014/30/EU

Condition: excellent (used), Year of construction: 2023, machine/vehicle number: 0-200-87-0913, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, edge thickness (max.): 3 mm, height adjustment type: electric, total length: 10,825 mm, year of last overhaul: 2026, Equipment: CE marking, documentation/manual, Used single-sided HOMAG edge-banding machine for straight edges – EDGETEQ S-500 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2023 EQUIPMENT / SPECIFICATION BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors each 3 kW (clockwise, counterclockwise), jumping function GLUING SECTION V20, consisting of: - QA65 glue application unit, with PTFE-coating (Teflon), with pneumatically operated glue gates - pneumatic clamping of glue application - Pre-melter for PUR glues - Edge magazine, edge thickness min. 0,4 mm to max. 3 mm Edge width (height) max 65 mm - 2-fold automatic edge roll changing magazine - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 4 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK25 horizontal, 2 motors, with straight/chamfer cutting function - Edge Trimming MS40 2x0.55 kW, top/bottom - Multifunction Corner Rounding MF60, 2 motors 0.4 kW (top/bottom) with linear motors, soft-touch - Profile (radius-) Scraping MN11, multi scraping tool, automatic positioning and adjustment (NC) - Flat Scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers), automatic adjustment - Buffing Unit FP10, top/bottom Dwedpfez Ikq Dox Al Sec Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 - Edge sequence control - change-over in the gap Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: excellent (used), Edge banding machine FORMAT 4 Tempora 60.06 glueBox - used Touchscreen, pivoting control panel, program memory, automatic pressure bridge adjustment, feed via conveyor chain, extendable workpiece support, diamond jointing cutter for up- and down-feed, glue pot located underneath, glue pot changing device, use of PUR adhesives possible, GLUEBOX, printing unit with driven roller, cross-cut saw with 2 HF motors, pneumatically pivoting cross-cut saw, flush/radius trimming unit, motorized positioning control of the trimming unit, x-motion PLUS, corner rounding unit with diamond-coated cutter, radius scraper, radius scraper with motorized positioning, surface scraper, operation-controlled Surface scraper, Inlet barrier, Release agent spray device, Lubricant spray device, Cleaning agent spray device, Year of manufacture 2022 ----- Technical specifications ----- Edge thickness for rolls: 0.4 - 3 mm, Edge thickness for strips: 3 - 6 mm, Workpiece thickness: 8 - 60 mm, Min. workpiece length: 140 mm, Feed speed: 10 m/min., Screen diagonal: 15 inches, Dimensions of jointing cutter: D 80 x 64 mm, Joining cutter power: 1.1 kW, Crosscut saw power: 0.35 kW, Milling station power: 0.75 kW, Extraction nozzle Ø: 80 + 160 mm, Compressed air connection: 7 - 10 bar, Total length: 4,872 mm, Dimensions (LxWxH): 4,872 x 1,511 x 1,468 mm, Weight: 1,500 kg Quality information: - All settings checked - Adjusted according to manufacturer's specifications - Complete basic inspection - Complete basic cleaning - Electrical system checked Dwedpfxeu R S Nws Al Sec - Pneumatic system checked - Ready for immediate use

Year of construction: 2010, operating hours: 7,546 h, condition: good (used), functionality: fully functional, machine/vehicle number: 04810, We are offering this well-maintained COMANDULLI OMEGA 100 edge grinding machine for round edges, manufactured in 2010. Manufacturer: COMANDULLI Model: OMEGA 100 Year of manufacture: 2010 Condition: good Category ID: 430 Machine type: Edge grinding machine for round edges Configuration: Belt running direction: left to right Pre-grinding support for end faces Thickness gauge 1+1 automatic pre-grinding supports 45° 8 end face grinding supports for straight and round edges 2 upper and 2 lower chamfering supports Swiveling device for chamfering supports for easy processing of pencil edges Finishing grinding support 2 roller tables, each 2m long The machine is currently in operation in Australia; the price includes transportation CIF to a European port of your choice. If you have any questions or require further information, please feel free to send us a message or call us. Dwsdpezyuckofx Al Sec

Condition: used, Year of construction: 2007, with feed unit for molded parts with hot melt glue specification Top condition cleaned, function tested, tested, trial run used, good condition Manufacturer: Artech-Biesse Type: Single Year of manufacture: 2007 Machine no.: 91009 CE type tested with automatic edge trimming, round edge banding tilt-adjustable worktable – for bevel edge banding Dwedovwgizjpfx Al Sjc extendable table extension with roller support feed system – steplessly adjustable edge thickness 0.4 - 3.0 mm workpiece height min. 10, max. 120 mm required space approx. 1400 mm x 1000 mm x 1600 mm weight approx. 320 kg total connected load 5.2 kW Location 97447 Gerolzhofen, free loaded, unpacked Transfer in as-inspected condition, without warranty or guarantee.

Condition: excellent (used), C.N.C. WORKING CENTER with 4 axes (X-Y-Z-C) for routering, boring, cutting and edge banding Numerical Control ICOS CNC (software IMAWOP) Max useful working area (without edge banding process) mm 6100 x 2000 x 125 Max useful working area (edge banding process) mm 3100 x 1925 x 100 (panel thickness) No. 10 movable rails (supports) 6 x length mm 1400, + 4 x length mm 1450 LED displaying both the axe X and axe Y position Vacuum cups (with No. 2 vacuum pump, capacity 140 m3/h) Clamps for workpieces fixing Safety side metal grids and front emergency carpets Motorized carpet to evacuate chips and wastes Separate electric and command cabinet No. 1 Vertical Electro-spindle HSK F63 ( Kw 18) Automatic Tools Changing System, with 18 folds (places) Banding group on board - (Y AXIS) Glueing Unit (P.U.R. Glue + Quick Melt unit) VT 100/100 with NORDSON premelter Edge coils supporting unit (No. 2 reels) OPTIONALS: N° 1 Aggregate Boring Unit, "cross" shape, with 4 horizontal spindles N° 1 Circular saw (diam. mm 200) N° 1 Combined unit: Corner rounding / Edge scraping (with glue scraping extension) Dwsdpfx Aloz Dtudo Sjc

Condition: used, Year of construction: 2008, Used machine Year of manufacture: 2008 Equipment and technical data: Edge banding thickness: max. 8-55 mm Edge banding with rounding unit: max. 45 mm Strip edge banding thickness: 0.4 - 8 mm Roller edge thickness: 0.4 - 3 mm Feed rate: 12 m/min Incl. rotatable control panel Dedew Nadgspfx Al Sswc HF joining unit, 2-motor Incl. quick-heating tank, interchangeable, Teflon-coated Incl. electronic positioning of the pressure rollers Incl. swiveling double miter saw unit Incl. flush trimming unit Incl. CNC-controlled chamfering, radius, and corner copying unit with nesting package Incl. radius pull blade with nesting package Incl. flat pull blade Incl. groove unit Incl. scraping unit Incl. spray unit Availability: short notice Location: Flörsheim

Condition: like new (used), functionality: fully functional, Used professional deburring machine Used, professional, and robust deburring machine for the efficient removal of burrs and rounding of edges on metal parts. Suitable for use in workshops and industrial production environments. The machine is equipped with 3 brushes and a powerful 2.2 kW motor. Thanks to its solid construction and weight of approximately 410 kg, the machine is suitable for professional and continuous use. Technical specifications: Max. material dimensions: 120 × 120 mm Brush diameter: 250 mm Number of brushes: 3 Motor power: 2.2 kW Voltage: 400 V Speed: 1,380 / 2,840 rpm Weight: approx. 410 kg Dwodpfx Aloz Ek Evo Ssc Condition: Used Available immediately. Inspection and testing of the machine are possible by appointment.

Condition: used, Year of construction: 2013, functionality: fully functional, operating hours: 334 h, power: 17.5 kW (23.79 HP), input voltage: 400 V, input current: 31 A, input frequency: 50 Hz, type of input current: three-phase, total height: 1,600 mm, total length: 6,600 mm, total width: 1,250 mm, overall weight: 2,900 kg, year of last overhaul: 2026, Equipment: CE marking, documentation/manual, We are offering this used OTT TORNADO-TOP edge banding machine, manufactured in 2013. The machine is in very good condition and was rarely used. It was only used to process PUR adhesive for custom-made products and individual pieces of furniture. No serial production. Type: TORNADO-TOP Year of manufacture: 2013 Power supply: 3~ N+PE Frequency: 50 Hz Rated voltage: 3×400 VAC Rated current: 31 A Dwsdpfx Aszvqclel Sec Rated power: 17.5 kW cos φ: Control voltage: 24 VDC Maximum fuse rating: 35 A Cable cross-section: 5×6 mm² If you have any questions or require further information, please feel free to send us a message or call us.

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: Homag Type: Optimat KDF 440 C Year of manufacture: 2017 Technical data Workpiece thickness: 8 - 60 mm Edge material: 0.4 - 8 mm (depending on the equipment) Feed rate: 8 - 18 m/min (stepless) Workpiece length min. approx. 120 mm Workpiece width min. approx. 60 mm Glue application EVA hot melt adhesive, optionally PUR-compatible Glue reservoir Teflon-coated, quick-change system possible Total connected load approx. 15 - 20 kW (depending on the equipment) Compressed air requirement: 6 - 7 bar Machine weight: approx. 3,000 - 3,800 kg Control system: powerControl / powerTouch CE marking Equipment: Joint milling Glue application Pressure zone Cut-off saw unit Milling unit top/bottom Dodszuykcspfx Al Sewc Corner rounding unit Scraping blade unit Edge finishing unit Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2021, input voltage: 400 V, input current: 17 A, input frequency: 50 Hz, type of input current: three-phase, We are offering this used HOMAG EDGETEQ S-240 edge banding machine, manufactured in 2021. The delivery also includes a KOGI dust extraction unit in a two-bag configuration with 2.2 kW power and 1,650 Pa suction capacity. The machine is additionally equipped with a glue pot for special applications. A valuation report (PDF) is attached. Processing units Joint trimming / pre-milling unit Corner rounding unit Radius scraper Glue scraper Buffing / polishing unit PUR-capable (PUR-ready system) Technical data Required air pressure: 6.5 bar Total machine length: 4.8 m Current operating hours: 460 h Machine data Type: EDGETEQ S-240 PROFI KDF 230 Serial number: 0-261-73-7111 Year of manufacture: 2021 Wiring diagram: 0-261-73-7111 Supply voltage: 400Y/230 V Number of phases: 3 Frequency: 50 Hz Maximum current at full load: 17.3 A Fuse rating: 20 A Short-circuit current: 5 kA Control voltage: 24 V Protection class: NEMA 1 Largest motor current: 4.6 A Highest heating current consumption: 2.3 A Djdjy Exwfspfx Al Sjwc Should you have any questions or require additional information, please do not hesitate to contact us by email or telephone.

Condition: used, Year of construction: 2014, machine/vehicle number: AH /117836, functionality: fully functional, year of last overhaul: 2025, Equipment: documentation/manual, Ideal machine for edge banding of solid wood panels MACHINING CAPABILITIES: Dedpfszcpixex Al Sjwc - Panel height (thickness) to be machined: 8 to 60 mm - Router pass: max. 90mm², 0 to 3 mm - Minimum panel length to be machined: 140 mm with an edge thickness >3 mm 200 mm with an edge thickness between 3 and 12 mm - Panel width to be machined: up to 2000 mm - Edge thickness: 0.4 to 3 mm in coil form, up to 12 mm in strip form Panel overhang relative to the chain (part protrusion): min. 30 mm - Edge width: recommended overhang: panel thickness + 4 mm - Feed system (2 feed speeds) 18 m/min for thin edges 12 m/min for strip edges (solid wood) - Distance between parts (depending on feed speed): recommended min. 800 mm MACHINE COMPOSITION: - Unwinding table, useful diameter: Ø780 mm - Electric positioning infeed guide - Chain conveyor belt, work surface height from the ground: 96 cm - Front extension table with rollers (serves as a support up to 2 m) - RT-E sanding unit (edge trimmers or routers) 2 x 4 kW, 9000 rpm - VC gluing unit Infrared preheating of the edge Pre-feeder for EVA granules, indicative consumption 8.5 kg/h "Fastblock" glue pot, pneumatic pre-cutting shear Pressing with 4 rollers, including 1 motorized roller, pressure with electric adjustment - K-SEL end trimming unit Rotation speed: 12000 rpm, motor inclination from 0 to 15° - RFK top/bottom flush trimming unit Rotation speed: 12000 rpm - RI 800 chamfering/flush trimming unit with copy pad Rotation speed: 12000 rpm, spindle inclination from 0 to 25° - GLC compact sanding unit, 1400 rpm Belt: 75 x 2700 mm, inclination from 0 to 5°, adjustable pneumatic pressure - SPN polishing station with textile polishing brush - Motorized operator return, useful width 1 m, with 2 roller tracks, spacing 34 cm Air cushion track and belt conveyor. Arrival height from the ground: 79 cm OTHER CHARACTERISTICS: - General power supply: 400 V, three-phase + N + T, 50 Hz - Installed power: IN 52 A nominal - Pneumatic supply: 8 - 10 bars, dry air, working pressure: 6 bars - Extraction: 6 x Ø50 mm, 1 x Ø80 mm, minimum flow rate 3000 m3/h - CE marking, lockable disconnect switch, emergency stop buttons

Condition: used, Year of construction: 2017, machine/vehicle number: 1000025340, functionality: fully functional, travel distance X-axis: 6,735 mm, travel distance Y-axis: 1,650 mm, travel distance Z-axis: 245,290 mm, workpiece height (max.): 60 mm, controller manufacturer: Biesse BH 660, bSolid, bEdge, rapid traverse Z-axis: 30 m/min, rapid traverse X-axis: 85 m/min, rapid traverse Y-axis: 85 m/min, Assembly of the the machine could be done by our subcontractor on the agreed price. Dsdeycvcxepfx Al Sswc

Condition: as good as new (ex-display), Year of construction: 2025, Compact and flexible in the smallest of spaces. At a length of only 2.13 m, workpieces are finished here. Equipped with a 1.1 KW high-frequency pre-milling unit and diamond-tipped spiral jointing cutter, Teflon-coated glue unit, pre-cut-off unit and HF multifunction milling unit, 2 free spaces for finishing units, such as a glue scraper unit and buffing unit. Easy operation via 3.5" color touch screen. ► Control via 3.5 inch color touch screen ► pre-milling unit with a 1.1 KW high-frequency motor with diamond-tipped spiral milling cutter in the counter-rotation ensures clean and Tear-free joining of the workpieces before the edge is banded ► Teflon-coated glue Pot with automatic stand-by function ► Automatic edge feeding with roller plate D = 600 mm for Edge material as roll goods as well as fixed lengths of 0.4 – 2.0 mm for ABS, PVC, or melamine edges ► Pressure station with 2 pressure rollers for optimal pressure of the Edge material. ► HF multifunction milling unit - suitable for radius and flush milling of the longitudinal edge, as well as for the front and rear edge of the workpiece, incl. vertical rounding of the edge ► 2 free spaces for finishing units such as glue scraper unit or buffing unit ► Workpiece chain feed with rubberized chain plates and Double Roller Upper Pressure Dwodpfx Asrrzklol Ssc ► Pressure bar with central adjustment and SIKO display ► Fixed workpiece support (optionally extendable workpiece support for large workpieces) ► 400 mm long infeed lineal with support ► LED lighting in the cabin (optional) ► Machining of workpieces with a thickness of 10 – 45 mm ► Feed speed 6.5 m/min ► Machine length 2130 mm 67641340f13ce

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: SCM Type: Olimpic K360 T-ER1 Year of manufacture: 2017 Technical data - Feed speed: 11 m/min - Edge thickness: 0.4 - 6 mm - Control: SCM control panel with display - Board thickness: 8 - 60 mm - Power supply: 400 V / 3~ / 50 Hz, 23 A - Min. workpiece: 140 x 90 mm Dwsdpfezuyk Nsx Al Sec Units Pre-milling - 2 counter-rotating diamond heads (up to 3 mm removal) EVA gluing unit Pressure zone with driven roller + 2 pressure rollers End trimming unit K-2 (straight / beveled, automatic switching) Flush trimming - flush, radius, chamfer Corner rounding R1/R2 Profile + surface scraper blade Polishing unit Anti-adhesive liquid system (2 liquids), edge roller feed Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 1993, Used machine Year of manufacture: 1993 Dwsdpfx Alszyy Avs Ssc Equipment and technical data:

Condition: used, Year of construction: 2016, Industrial automatic edge banding machine SOLUTION XD KEY FEATURES "E-TOUCH" CONTROL WITH AUTOMATIC PROGRAMMING: A SINGLE "TOUCH" IS ALL IT TAKES TO OPERATE THE MACHINE STANDARD PRESSURE DEVICE WITH DRIVE BELT FOR OPTIMAL PANEL GUIDANCE EDGE BANDING OF ROLL MATERIAL, STRIP EDGES AND SOLID WOOD EDGES GENERAL FEATURES Single-sided edge banding machine in left-hand version for edge banding of roll material and strip edges with all conventional hot melt adhesives. The base frame consists of a stable steel welded frame with higher rigidity, which provides optimal support for the installation of the processing units. The upper pressure beam consists of a thick-walled steel profile and a double trapezoidal drive belt, which is automatically positioned according to the panel thickness. Height adjustment with display on the upper pressure beam and on the operator panel. Manual workpiece feeding system with a large-sized work area and increased support surface facilitates the feeding of large workpieces. Adjustable infeed fence for two positions with automatic selection for processing with or without a pre-milling unit. Upper working units are attached to the pressure beam and mechanically connected to ensure automatic adjustment when changing panel thickness. Lower working units are attached to the machine frame or to the longitudinal support for precise referencing to the panel. All high-frequency motors are operated via frequency inverters. Each unit is equipped with its own inverter for optimal flexibility and improved machine production times. Protective hood for all units positioned after the glue application unit. Polycarbonate windows ensure a good view of the units during processing. Interior lighting of the hood. Protective hood with sound-absorbing material for lower noise emissions during operation. Spacer on the infeed fence allows the machine to be fed with the correct spacing. The spacing is automatically adjusted to the selected feed rate. Dust extraction port arranged on the pivoting control panel, positioned in the infeed area, is adjustable for ergonomic operation. The electrical system complies with current regulations. Electrical components are housed in a metal housing, attached to the machine frame and equipped with doors for easy access in case of maintenance. Standard voltage is 400 V EU 50 Hz (with neutral conductor). Material feed is via a feed chain with 80 mm wide chain plates made of rubberized nylon, for optimal guidance and high load capacity. The chain slides on 2 guides made of hardened and ground steel, one round and one flat guide, to guarantee straight feed and to protect against lateral displacement. Automatic chain lubrication. The amount of lubricating oil is optimized by the control system depending on the panels being processed. External support roller track positioned along the entire length of the machine; consisting of an extendable opening system up to 650 mm (for panels with a maximum width of 1200 mm). E-TOUCH PC control system for quick and easy execution of the main functions of the machine. Includes: – Processing of programs in Just in Time mode – Possibility of management via bills of materials – Possibility of management by Dodpfjxy Tm Ijx Al Sswc

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: Felder Type: G680 Year of manufacture: 2017 Djdpjz Arwqefx Al Sjwc Technical data Power supply: 400 V, 3-phase, 50 Hz Power: 7.22 kW Current consumption: 18.6 A CE marking: Yes Equipment: Jointing unit Gluing unit Pressure zone Cutting unit Milling unit Corner rounding unit Scraper blades Polishing unit Additional glue tank Dust extraction connections with flexible hoses Control panel with digital display Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: excellent (used), Year of construction: 2016, power: 12.3 kW (16.72 HP), input voltage: 400 V, input current: 31 A, input frequency: 50 Hz, type of input current: three-phase, We are offering this used Hebrock AKV 3005 DK-F edge banding machine, manufactured in 2016. Voltage: 400 V Frequency: 50 Hz Current: 31.7 A Power: 12.3 kW Machine number: 3141 Year of manufacture: 2016 PLC control with touchscreen The asking price is 20,500 euros net (negotiable). Dwedpfxoz Afcto Al Sec If you have any questions or require further information, please feel free to send us a message or call us.

Condition: excellent (used), Year of construction: 2017, I sell the fully equipped edge banding machine BRANDT KDF 230 AirTec, year 2017: Configuration: Entry fence manual adjustable Premilling manual adjustable Edge banding EVA glue / PUR glue possible / AirTec unit Material pressure zone manual adjustable End cutting saws pneumatic adjustable Tilting radius milling top + bottom manual adjustable Corner rounding 1-motor manual adjustable Radius R2 scrapers pneumatic adjustable ( set of R1 included) Control panel Working thickness adjustment manually Material height 8-60mm Edge thickness 0,4-3mm Feeding speed 10m/min. Total length including feeding plate 5070mm Very good condition, fully working! Dedpfx Aljythxme Sewc Including full documentation and CE. Available immediately.

Condition: as good as new (ex-display), Year of construction: 2025, One-sided automatic edge banding machine with pre-milling unit, direct glue application to straight workpieces (EVA-PUR Glue pot with run-out function/optional), HF-cut-off saw station with 2xMotors , HF-top and bottom milling unit, corner rounding unit, chain feed, double roller top pressure, extendable work piece support, signal lamp for work piece sequence and synchronisation of working units by encoder. For ABS, PVC, melamine and strong wood veneer roll material as well as fixed lengths from 0.4 – 3.0/6.0 mm and of 8 – 60 mm work piece thickness. Speed: 10,0 m/min.; 8,0 m/min. with corner rounding • 3 spaces for finishing units • 10“ Colour Touch screen →Automatic edge feeding for roller material over turntable D = 800 mm →Longer infeed lineal (650 mm) →Two reverse, operating-controlled pre-milling units with diamond charged helical joining millers provide a neat and tear-free premilling of the work pieces before the gluing of the edge material →Glue application directly to workpieces: Teflon-coated glue pot with a capacity of 1,5 kg, leak proof with glue supply from below (excess glue automatically flows back into the glue pot). Glue roller allows exact dosage of glue. Separate glue roller temperature adjustment. Electronic temperature control with automatic stand-by function (reduces probability that the glue burns if the machine is not used for a longer periods and is still turned on). Optional: EVA/PUR gluepot with run out / cleaning function for quick change of glue →Pneumatically operated cut-off knife from roll material up to 3mm edge thickness →Automatic feeding magazin (70mm magazin capacity) with spiked roller for solid wood →Pressure unit consisting of one driven pressure roller synchronized with glue spreading roller and two of smaller diameter, conical, one positive and one negative pressure roller with spring tension for a nearly invisible joint of the edge material with the work piece , adjustment of the pressure unit with digital readout. →High-frequency cut-off saw equipped with 2xHF motor 0.55 kW, 12,000 rpm, 2 saw blades and high-precision linear guides ensure a clean and precise saw cut, with extraction hood. →High-frequency top and buttom milling station, 2 powerful 0.55 kW high-frequency motors with HM-WPL special millers; suitable for radius, bevel and flush milling, horizontal and vertical scanning of the work piece; aggregate adjustment equipped with digital readouts for setting to various edge types; 2 extraction hoods for shavings with central extraction nozzle 2 x Ø 100 mm; height adjustment of the upper aggregate with the top roll pressure →Corner rounding unit : Automatic processing of corner edges up to 2 mm edge thickness. Equipped with one high frequency motor 0, 27 kW, selectable on operating panel. One side (front or back edge) or both side corner rounding unit. →Rotatable control panel with 10“ color touch screen controls glue temperature settings, automatic temperature reduction for stand-by function of the machine, switching on and off of aggregates and error diagnosis, incl. digital Meter counter Dodpfx Asl Rix Nsl Sewc Additional finish aggregates : →Radius scraper unit : With a slight draw cut eventual radius milling traces are removed to provide a perfect finish. The fine adjustment is made by digital readouts. →Glue scraper unit : Removes eventual glue rests with a slight draw cut from the glue joint of th

Condition: excellent (used), Double side - Independent Machine (or 1st and/or 2nd in a line) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Panels thickness (min/max) mm 12 - 40 Working width (min/max) mm 250 / 2500 Numerical Control /Software Power Control 22 / woodCommander Adjustable feeding speed (m/min) 15 - 35 Safety and sound-proof enclosures/cabins Distance (center-axes) of the Disappearing Dogs (mm) 1000 SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Anti-chipping Milling Unit (1 x Kw 4,5) Hogging Units KD 11 (2 x Kw 6,6) EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt + Quick Melt Unit) A3 Dodjzrd Rzjpfx Al Sjwc Pressure zone A Edge coils supporting unit (No. 2 of reels) with servo-assisted edge feeding Snipping Unit HL86 (2 x Kw 0,22) Rough Trimming Unit BF10 (2 x Kw 0,55) Fine Trimming Unit PF20 (2 x Kw 0,4) FRRE SPACE for Corner Rounding unit ( Contour Trimming) FF 12 (2 x Kw 0,4) Profile Scraping unit PN 10 Finish processing unit (Glue scraper + Buffing unit) FA 11 Spraying Unit (for polishing liquid)