Used Baling Press for sale (12,558)

Condition: good (used), Year of construction: 2011, operating hours: 40,000 h, functionality: fully functional, pressing force: 88 t, filling opening width: 990 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, overall weight: 23,000 kg, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 643 m³/h, Good day, We hereby offer, subject to prior sale, a used baler including conveyor belt, wire tying stations, and bale chute from the manufacturer HSM GmbH + Co. KG, model VK 8818 FU. The following technical specifications were taken from the manufacturer's operating manual and brochures; we do not assume any liability for the correctness or completeness of this information. Manufacturer: HSM GmbH + Co. KG, Germany Model: VK 8818 FU Year of manufacture: 2011 Operating hours: approx. 40,000 hours as of July 2025 Main press force: 880 kN Specific press force: 107 N/cm² Feed opening dimensions: 990 x 1,800 mm Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Tying: 5-fold horizontal, fully automatic Kodpfjymmtcsx Al Nolu Baler dimensions (set up): 12,130 x 4,800 x 3,270 mm (L x W x H) Overall installation dimensions with conveyor system: 14,000 x 23,000 x 7,745 mm (L x W x H) Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The press is in good condition and will be replaced with a new, larger press in May/June 2026. Until then, the machine can be inspected in operation with material. We would be pleased if this baler is of interest to you. Your Mertens & Frowein GmbH service team

Condition: excellent (used), Year of construction: 2020, machine/vehicle number: 161.40.492, Used Strautmann bale press, type: BalePress 3, serial number: 161.40.492, year of construction: 2020, with tape extraction hook Power supply: 230 V 50 Hz Electrical Power: 0,75 kW Protection class: IP54 Pressing force: 27 kN Press stroke: 580 mm Weight of the machine: 275 kg Transport dimensions (lxwxh):1070 x 754 x 2110 mm (without pallet) 1070 x 754 x 1945 mm Filling opening (wxh): ca. 700 x 450 mm Cycle Time: 27 sec. Bale weight 30 kg Bale size in the chamber (lxwxh)*: 500 x 700 x 500 mm Bale tying: strapping with two twines, PP band ADVANTAGES Kodpsvvk T Iofx Al Nslu Easy to install and transport Easy to handle bales Practical emptying of bales Foil/cardboard mode switch Simple and safe operation Stable door locking system Stable guide of the press plate "D" level security system. Small space required BP3: Bale tying system with open door; BP3CD: tied bales with door closed Solid construction Wheel door lock Ideal for small shops. The Strautmann BalePress 3/3CD is a small, single-chamber baler. At the same time, it is perfectly suited for baling common and smaller quantities of paper, foil, PET bottles and plastic waste and, thanks to its compact design, it can also fit into a very small space. It is clearly the best alternative for our partners with less waste and a waste container with a small footprint. Depending on the pressed material, the 3 ton pressing force can result in a volume reduction of up to 90%. The machine can produce relatively small and therefore easy to handle bales of up to 35 kg. By using it, significant savings in storage and transportation costs can be achieved. Bales are easier to transport and sell than untreated waste. Due to its dimensions, the machine can also fit in a very small space, and because of this, the baling technology is no longer available to our partners who have limited space. Price 3.490 Euro + VAT, negotiable, FCA: Oradea/Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: new, Year of construction: 2024, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW * Piston shafts will be induction-hardened and chrome-plated. * The pressing box will be HARDOX plates. * Pumps and valves used in the hydraulic system will be MARZOCCI brand. Ksdpfsdfc Unjx Al Nolu * The hydraulic valve control lever unit will be SALAMI or VALVOIL brand. * There will be automatic Oil Cooling/Heating Systems. * There will be an oil temperature control screen on the electric panel and an oil level control on the hydraulic oil tank. * The machine will be manually operated. * All electric-electronic material will be from the SCHNEIDER or SIEMENS brand. * Machine will be under AYMAS Makina San. ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or 2.500 working hours whichever comes first. * The machine is CE and EAC certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. SEE THE TECHNICAL DESCRIPTION BELOW Bale Size: 600mm x 400mm x ... Container Dimension (Width x Length x Height ): 620mm x 1.300mm x 620mm Capacity:

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Bale Size: 500mm x 500mm x... 2. Container Dimensions (Width x Length x Height): 2.000mm x 2.500mm x 1.100mm 3. Capacity: 15-20 tons/hour (steel) Kljdsgwa T Ropfx Al Nju 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 300 tons 8. Maximum Working Pressure: 300 bars 9. Electric Motor: 2 x 75 kW = 150 kW 10. Machine Dimensions (Width x Length x Height): 10.000 mm x 10.000 mm x 4.000 mm 11. Machine Weight: 55.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Bale Size: 400mm x 400mm x... 2. Container Dimensions (Width x Length x Height): 1.000mm x 2.000mm x 800mm 3. Capacity: 4 tons/hour (Steel), 5 tons/hour (Copper), 2 tons/hour (Aluminium) 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 210 tons 8. Maximum Working Pressure: 300 bars 9. Electric Motor: 37 kW 10. Machine Dimensions (Width x Length x Height): 3.400 mm x 6.800 mm x 3.000 mm 11. Machine Weight: 18.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects. Klodpfxodfc Iyo Al Nou

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: THE MACHINE WILL BE BRAND NEW The compression chamber walls are covered with HARDOX material for long-term life-cycle and friction resistance. A hydraulic Oil Cooling system is implemented for efficiency in hot climate conditions. Cylinder Rods are induction-hardened and chrome-plated. Pumps and valves of hydraulic systems are from worldwide reputable brands such as PARKER, and BOSCH-REXROTH. The machine is fully automatic by PLC control. It is easy to use with the help of the touch screen. All electrical and electronic parts are by SCHNEIDER and SIEMENS Brands. The machine is CE-certified. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. Machine will be under Aymas Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours. SEE THE TECHNICAL DESCRIPTION BELOW Bale Size 400mm x 400mm x... Bale Weight 120-180 kg (Steel), 50-80 kg (Aluminium),150-200 kg (Copper) Press Box Dimensions (Width x Length x Height): 1.000mm x 2.700mm x 900mm Loading Bunker Dimensions (Width x Length x Height): 1.650mm x 2.300mm x 800mm Feeding Opening: 1.000mm x 1.600mm Kledpedfcqasfx Al Nou Capacity*

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: THE MACHINE WILL BE BRAND NEW The compression chamber walls are covered with HARDOX material for long-term life-cycle and friction resistance. A hydraulic Oil Cooling system is implemented for efficiency in hot climate conditions. Cylinder Rods are induction-hardened and chrome-plated. Pumps and valves of hydraulic systems are from worldwide reputable brands such as PARKER, and BOSCH-REXROTH. The machine is fully automatic by PLC control. It is easy to use with the help of the touch screen. All electrical and electronic parts are by SCHNEIDER and SIEMENS Brands. Keded Iya Nepfx Al Nolu The machine is CE-certified. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. Machine will be under AYMAS Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours. SEE THE TECHNICAL DESCRIPTION BELOW Bale Size 400mm x 400mm x... Bale Weight 100-180 kg (Steel), 40-100 kg (Aluminium),120-180 kg (Copper) Press Box Dimensions (Width x Length x Height): 1.000mm x 2.600mm x 900mm Loading Bunker Dimensions (Width x Length x Height): 1.500mm x 2.200mm x 650mm Feeding Opening: 1.000mm x 1.600mm Capacity*

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h Kedpfezdn H Rjx Al Nslu bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), Year of construction: 1994, Brand: HSM Kledpfxozc Hhxs Al Nou Model: 155 VL Year of construction: 1994 Pressing force: 157 kN Voltage: 400 Max. bale weight: 250 kg Bale dimensions: 110 x 70 x 95 cm Machine weight: 950 kg Machine dimensions: 144 x 100 x 234 cm Feed opening dimensions: 110 x 59 cm

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. Klodpey S Rqwofx Al Nou 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Kljdpozaqymefx Al Nou Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request. Transportation is also possible.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h Kodpfxjy R Nnfe Al Nolu bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Klodpsvq Rtksfx Al Nsu Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Model: Balestrini 1+1 dual-spindle turret press, patterning machine, 2500mm worktable size, used, tested. Klsdpszfi Sdofx Al Nju

Condition: good (used), Manufacturer: Comp Type: SB5 Motor: 2.2 kW Stroke length: 500 mm Ksdpeh Eic Asfx Al Nelu Chamber size: 500 x 350 x 400 mm

Condition: ready for operation (used), Year of construction: 2012, pressing force: 40 t, Manufacturer: HSM Klodpex D U N Sofx Al Nju Model: HL 4010 Year of manufacture: 2012

Condition: used, Year of construction: 2012, pressing force: 4 t, HSM V-Press 504 waste paper baler - used The HSM V-Press 504 vertical baler is a compact yet extremely efficient device designed for pressing cardboard and plastic waste. Thanks to its robust construction, simple operation, and modern control system, this model is the ideal solution for manufacturing companies, warehouses, stores, and logistics centers where significant amounts of packaging waste are generated every day. The baler, manufactured by the German brand HSM, ensures reliable operation and a long service life. Key advantages of the waste paper baler: 40 kN crushing force – effective waste compression, reducing volume by up to 95%. Efficiency and ergonomics – the crushing process starts automatically when the door is closed, and the piston returns to its starting position automatically. Modern control system – a microprocessor with a membrane keyboard and graphic text display ensures easy monitoring of the work process. Double door with lever – safe and convenient operation even with intensive use. Compact bales up to 60 kg – facilitate transport and storage of processed waste. Integrated bale ejector – increases operator safety and comfort. Energy-efficient operation – 1.1 kW motor allows for full functionality with low energy consumption. Stable, durable construction – guarantees reliability over a long service life. The offer applies to the HSM V-Press 504 waste paper baler: • Product code: MTP006524 • Product condition: used • Year of manufacture: 2012 • Model: V-Press 504 Kledpfx Aljyim Ayj Neu • Width: 102 cm • Depth: 81.5 cm • Height: 193 cm • Weight: 290 kg • Power: 1100 W • Voltage: 230 V Net price: €2,859.00 per unit * I have large quantities available, with the possibility of negotiating the price for larger orders. * Transport possible throughout Europe. * The above offer does not include transport costs. * Location: Chmielów/Tarnobrzeg, Poland.

Condition: used, functionality: fully functional, This offer is for a used ‘Xerox Iridesse Production Press’ colour production system Items for sale: 1 x Xerox Iridesse Production Press with the following specifications: Kledpfozdq H Hex Al Nju Includes Fiery Server NX PRM-17 (EX-P6) Includes A-CF03 paper deck Includes stacker Not the right configuration? It’s no problem to configure the machine to your requirements. Please feel free to contact us! Meter readings: Total: Approx. 6,817,985 pages Colour: Approx. 6,076,014 pages Black: Approx. 741,971 pages Condition: This is a second-hand machine, which may show signs of use (minor scratches or discolouration). The machine has been tested for functionality A test print can be seen in the photo Packaging and shipping: You are welcome to view the machine during our business hours. Please arrange an appointment! Seaworthy packaging and worldwide shipping available on request! A functional test will be recorded on video for you prior to dispatch or collection. For further information, you are of course welcome to contact us directly.

Condition: used, With this offer, you are purchasing a used manual transfer press ‘Lotus LTS 150 B from 2023’. Item for sale: 1 x Lotus LTS 150 B with the following equipment: Includes DTF gel oven Year of manufacture: 2023 Condition: This offer is for a used device, which may show signs of wear Klodpfx Ajx Eg Upjl Neu (minor scratches or yellowing). The device has been tested for functionality. Packaging and shipping: You are welcome to view the device during our business hours. Please make an appointment! Seaworthy packaging and worldwide shipping available on request! For more information, please feel free to contact us personally.

Condition: used, Year of construction: 2003, pressure 400 t distance between columns 1060 mm stroke 450 mm no. of strokes 15 - 30 /min distance table/ram, max. stroke up, adjustment up 1160 mm Klodpfxevzxpuo Al Neu table surface area 1000 x 700 mm capacity of ejector in table 2 x 16 t ejector stroke of ejector in table 125 mm Die cushion pressure in table 120 t Die cushion stroke in table 2 mm capacity of ejector in ram 2 x 4 t stroke of ejector in ram 100 mm ram surface 1000 x 700 mm column travel -side 630 mm power capacity 55,0 kW weight 50,0 t year of manufacture 1986 - overhaul 2003 multi-station press with automatic parts feed, Transfer, drawing cushion in table (2. stage) as is where is, WITHOUT putting into operation, stored in dismantled condition

Condition: used, functionality: fully functional, This listing is for a used “Xerox Colour J75 Press” color production system Items for sale: 1 x Xerox Colour J75 Press with the following features: Includes Fiery EX C75 Includes A-CF01 paper deck Includes Bros-Finisher + LFN-7+JGW Not the right configuration? It’s no problem to configure the machine to your specifications. Feel free to contact us! Meter readings: Total: Approx. 1,272,538 pages Color: Approx. 1,099,543 pages Black: Approx. 172,995 pages Kodpoza Db Dsfx Al Nslu Condition: This is a used device, which may show signs of use (minor scratches or yellowing). The device has been tested for functionality A test printout can be seen in the photo Packaging and Shipping: You are welcome to view the device during our business hours. Please schedule an appointment! Seaworthy packaging and worldwide shipping available upon request! A functional test will be recorded on video for you prior to shipping or pickup. For more information, you are of course welcome to contact us directly.

Condition: used, functionality: fully functional, This listing is for a used “Xerox Versant 180 Press” color production system Items included: 1 x Xerox Versant 180 Press with the following features: Ksdpfxjza A Euo Al Nolu Includes Fiery E300-5 Includes Paper Deck A-CF01/A-GW03 Includes Booklet Finisher A-FN13 Not the right configuration? It’s no problem to configure the machine to your specifications. Feel free to contact us! Meter readings: Total: Approx. 729,330 pages Color: Approx. 505,865 pages Black: Approx. 223,465 pages Condition: This is a used device, which may show signs of use (minor scratches or yellowing). The device has been tested for functionality A test printout can be seen in the photo Packaging and Shipping: You are welcome to view the device during our business hours. Please schedule an appointment! Seaworthy packaging and worldwide shipping available upon request! A functional test will be recorded on video for you prior to shipping or pickup. For more information, you are of course welcome to contact us directly.

Condition: used, functionality: fully functional, This offer is for a used ‘Xerox Iridesse Production Press’ colour production system Items for sale: 1 x Xerox Iridesse Production Press with the following specifications: Includes Fiery Server EX-P6 Includes paper decks A-CF03 + A-CF04 Includes stacker Not the right configuration? It’s no problem to configure the machine to your requirements. Please feel free to contact us! Meter readings: Ksdpfxjzap Sbe Al Nslu Total: Approx. 14,303,610 pages Colour: Approx. 14,006,634 pages Black: Approx. 296,976 pages Condition: This is a second-hand machine, which may show signs of use (minor scratches or discolouration). The machine has been tested for functionality A test print can be seen in the photo Packaging and shipping: You are welcome to view the machine during our business hours. Please arrange an appointment! Sea-worthy packaging and worldwide shipping available on request! A functional test will be recorded on video for you prior to dispatch or collection. For further information, you are of course welcome to contact us directly.

Condition: good (used), Impress HM 4 Hot Stamping Press This machine is in very good condition and ready to use. This machine is from the popular Impress hot stamping machine manufacturer, manufactured in the UK. Description The Impress hot stamping press is a hot stamping and embossing press for paper and plastics. It’s a useful device in any advertising agency or digital printing house. The manual press is powered by only 230V. A powerful press with adjustable pressure ensures repeatability and very high pressure between the die and the material. The machine features a worktop with a slide-out function, adjustable embossing depth, a heating plate with a thermostat, and an automatic foil feed. Specifications: Heating temperature control via thermostat Klodpfxjzday Ro Al Nou Heating plate pressure mechanism: mechanical Press force: 1000 kg Power consumption: 500 W Power supply: 230 V Machine weight: 50 kg Plate size: 150 x 150 mm.

Condition: good (used), HFS-210 Hot Stamping Press The machine is in perfect condition. Year of manufacture: 2019. Description: The HFS-210 Hot Stamping Press is a pneumatic hot stamping press for hot stamping, embossing paper, and plastics. A useful device in any advertising agency or digital printing house. The cycle is operated manually. The pneumatic drive ensures repeatable work and very high die pressure on the material. The machine is equipped with an automatic foil feed, which significantly shortens the time of a single hot stamping cycle, a worktop, adjustable embossing depth, a hot plate ground to 0.01 mm accuracy, which significantly improves the quality of embossing with large dies, a control panel, and modern OMRON controls. Specifications: MODEL: HFS-210 Hot Stamping Press Heating plate size: 210 x 150 mm Work table area: 500 x 350 mm Heating temperature control: via display up to 200°C Holding foil adjustment: Automatic, potentiometer-controlled Hot plate pressure mechanism: pneumatic Height of the gilding stack: 68 mm Press force: 0.6 T Power consumption: 900 W Power supply: 230 V Machine dimensions: 750 mm (W) x 530 mm (D) x 1670 mm (H) Machine weight: 120 kg The machine includes a cross table and a die mounting frame. An instruction manual is included. Klodszdau Ujpfx Al Nsu