Used Horizontal Press for sale (18,188)

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 2,000 mm, filling opening length: 1,020 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, year of last overhaul: 2026, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: Bwsdpfxsy Uruvj Afkjn 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: like new (used), Year of construction: 2022, machine/vehicle number: DF0147, Pressure: 150 t Total power requirement: 20 kW Machine weight approx.: 11.5 t space requirement approx.: 8800 x 1800 x 2200 mm pressure setting infinitely variable via rotary control : 15-150 t cylinder diameter : 100 mm pressing speed (infinitely variable via joystick) : 0-9,9 mm/s servo motor : 2 kW cooling unit : 1 kW Oil tank (under press table): 350 l Oil cooling (electric): 1 kW (max) Profile straightening press 150 T with two pressure cylinders. Bodpefxygwefx Afkewn The straightening machine is prepared for the particular type of material by interchangeable rounded spacer elements. The replacement of the 10 inserts is done manually by simply pushing them into the holding grooves. The scope of delivery includes basic equipment for one profile. The program for the respective profile is then called up on the monitor. The monitor shows the ideal line and, in addition, an ascending and descending millimeter scale with 0.5 mm lines. The profile to be straightened is now placed on the left side of the table, pushed against a holder and clamped with a quick-clamping device. Both the holder and the quick-clamping device are mounted on a clamping plate for quick adjustment. This clamping plate moves on a linear guide from left to right and vice versa. Transport is by a chain drive and a servo motor. The movement is triggered by a joystick on the control panel. After the profile has been clamped, the operator moves the clamping platen into the press using the joystick. The travel speed is up to 100 mm per second, but can be continuously adjusted down to 10 mm per second. To do this, it is sufficient to pull the lever of the control system slightly less. A high-resolution camera now shows the profile in the press. The operator sees exactly the deviation from the ideal line. Depending on the need, he now pushes or pulls the profile to the desired accuracy. He then continues to move slowly through the press, seeing in detail on the monitor whether the profile is now straight. Depending on the need, he can now move the profile forwards or backwards and readjust it. After the profile has been straightened, it moves out of the press on the right and can be removed. If desired, the clamping platen now moves back to the loading position on the left or it is now loaded from the right to save time. The press may only be operated under the following conditions: Perm. ambient temperature: 5-60 °C Permissible relative humidity: at 20°C - 90%, at 40°C - 50% Height of the installation site NN: + 1000 m Perm. fluctuations E-mains: +/- 10%.

Condition: used, Technical details: pressure: 160 t table surface area: 1.260 x 600 (vertical) mm table plate diameter: 1260 x 600 x 70 (vertical) mm ram surface area: 700 x 360 mm throat: 300 mm Bwsdpfxou Nfpuo Afkjn weight of the machine approx.: 9000 kg dimensions L x W x H: 3,7 x 1,5 x 2,2 m distance base - ram: 1.000mm mounted ram construction: L:660 x W:300 x H:370mm rollers 1x on the right and 1x on the left with vertical adjustment 250mm. (Ø 80x300mm) *

Condition: used, Technical details: pressure: 200 t stroke: ca. 200mm mm table surface area: L:1200xH:450 mm jaw width: 1000x200 mm total power requirement: 18 kW weight of the machine ca.: 15 t dimension machine xH: 4,5x1,5x2,2 m Beam - Straight Bending Machine - electric box (LxWxH:0,85x0,8x2,7m) - chuck intake: LxW 1200x220mm - chuck adjustment 200mm moveable - opening width of chucks 300mm - manual control accessories: Bwodpfxsu Nfrpo Afkon - div. limit stops, tools, try square and marking gauges i.D. *

Condition: used, Year of construction: 2008, Technical details: pressure: 6 t stroke: 1020 mm total power requirement: 3,5 kW Can only adjust between tips * Bodew Ng D Tspfx Afkewn

Condition: excellent (used), Year of construction: 2015, Equipment: documentation/manual, HSM HL 4010 Re / Li horizontal baler. Equipped with a loading tipper for the basket. Manufactured in 2015. Very good condition - regularly serviced by an authorized service center. Ready for use. Available for binding with wire, string, or polypropylene tape. Bedpfx Afezaqlcskswn Semi-automatic baler system with a 40-ton pressure for economical volume reduction of residual (recyclable) materials in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulation mats and other compressible materials. Press force: 400 kN Transport width: 1,767 m Transport height: 2,489 m Transport length: 5,573 m Weight: 4,500 kg Drive power: 7.5 kW Bale weight (depending on material): 300-350 kg Bale length x width x height: 750 x 1200 x 750

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 80 t, bale weight: 600 kg, Equipment: documentation/manual, DIXI 80 SLD horizontal press Bwjdpfsy Udwpjx Afken Semi-automatic press system with 80 tons of pressure for economical volume reduction of residual materials (recyclable) in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulating mats and other compressible materials. Pressure force : 80 t Electrical connection : 400 V 50 Hz; 11 kW; D-32 A (option: K-32 A) Cycle – average approx. : 35 sec Length approx. : 4,320 mm (without lifting device and pallet) Width approx. : 1,830 mm Height approx. : 2,620 mm (with hopper) Loading opening (WxD) – housing : 1,040 x 1,110 mm Bale dimensions : 1,120 x 1,120 x 1,200 mm Bale weight approx. : 500 – 600 kg Tying 4 manual, wires with quick-release eyelets Machine weight approx. 8,000 kg (without bale)

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, pressing force: 70 t, Equipment: documentation/manual, HSM HL 7009 Re / Li horizontal baler. The machine is in very good condition and regularly serviced by an authorized service center. This baler is designed for larger waste disposal projects in retail outlets and small and medium-sized central warehouses. Bales from the HL 7009 model have a cross-section of 1100 x 1100 mm and, with a bale length of 1200 mm, can weigh up to 600 kg, ensuring optimal utilization of the truck's payload. Pressing force: 700 kN Specific pressing force: 58 N/cm² Bwsdpfey Tt Riex Afkon Drive power: 10.5 kW Voltage / frequency: 400 V / 50 Hz Idle capacity (theor.): 42.97 m³/h Loading opening width x length: 890 x 1020 mm Bale width x height x length: 1100 x 1100 x 1200 mm Total length x width x height: 5366 x 2525 x 2559 mm Bale weight: 600 kg

Condition: excellent (used), Continuous horizontal press, to compact and pack materials such as cardboard, paper, plastics and others. IMABE IBERICA brand, pressure 125TN, loading mouth 1800 * 1000mm, with blades on the top of the compaction carriage that allows cutting the excess material above the compaction tunnel. Folding compaction tunnel, both at the top and on the sides, for greater retention of the material, outlet for bullets of dimensions 1050 * 1100mm and adjustable length. Automatic tying system, lateral, by 5 wires, for high production 30-35ton / hour. Fully rebuilt and revised in 2019 Bedpfx Afsv U R Agjkjwn

Condition: excellent (used), Block press horizontal 5000 mm length 800 mm width 12 cylinders 5 hold downs Bodpfol D T D Eox Afkewn

Condition: used, Hydraulic Horizontal Straightening Press, Horizontal Press STENHOJ Type 40 Horizontal hydraulic press for straightening work on steel beams or welded structures Serial no. 42615 Year of manufacture: 1984 Refurbished in 2025 Pressing force: 40 tons Ram stroke: 300 mm Piston rod diameter: 80 mm Working height: 780 mm (floor to center of piston rod) Table size without pressure pads: approx. 1000 x 290 mm Installation dimension, ram + press block to counter bearing: 260 mm (with pressure pads on ram and counter bearing) Installation dimension, ram without press block to counter bearing: 440 mm (without pressure pads on counter bearing) Bwsdsydqd Hspfx Afkjn Height of the two adjustable pressure pads: 130 mm Pressure pad width: 220 mm Advance speed: 10 mm/s Return speed: 20 mm/s Hydraulic tank capacity: approx. 60 liters Motor power: 3 kW Power supply: 400 Volt, 50 Hz - Cylinder stroke operated manually via an actuation lever, sensitive control via mechanical control valve - Pressing force readable via pressure gauge - Ram stroke position with actual value display, digitally readable, ideal for precise repeatability of pressure points during straightening - 2 adjustable counter bearings via threaded spindle (centric parallel adjustment from 290 to 890 mm) - Straightening tools with rounded pressure faces - Infeed rollers for material support, centrally height-adjustable via handwheel (roller width = 250 mm) Required space (L x W x H): 170 x 140 x 100 cm Weight: 1250 kg In excellent condition

Condition: used, Year of construction: 1987, machine/vehicle number: 33879, Stehendbogenauslage - Horizontal Stack Delivery with Pressing Stahl SBP 46Year 1987 - Serial-No. 33879/87-134584 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Bwodpfx Afsh Aygfskjn Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Bündelpresse / Bunch Press - horizontal La Fornigrafica BPHydraulische horizontale Bündelpresse / hydraulic horizontal bunch Press Pressdruck stufenlos einstellbar / Pressure steppless 0 – 2.500 kg Einsatzlänge / Infeed length max. 820mm Pressplattengrösse / Press plates size 340 x 260 mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect Bsdpoh R Udwjfx Afkown On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Year of construction: 1994, machine/vehicle number: 49504, Stehendbogenauslage mit Markiereinrichtung - Horizontal Stack Delivery with Pressing - Marking Stahl SBP 46.2Year 1994 - Serial-No. 49504/94-218513 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Bwsdoh Ax S Depfx Afken Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Year of construction: 1979, machine/vehicle number: 14256, Stehendbogenauslage mit Presswalzenauslage - Horizontal Stack Delivery with Pressing Stahl SBP 40Year 1979 - Serial-No. 14256/79 Size width max. 400mm Bwsdsrgbz Eopfx Afksn Vertical press delivery -modified with SELFControl- Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Bündelpresse / Bunch Press - horizontal Tränklein BPHydraulische horizontale Bündelpresse / hydraulic horizontal bunch Press Bodpfx Afeiwg A Eokjwn Pressdruck stufenlos einstellbar / Pressure steppless 0 – 2.500 kg Einsatzlänge / Infeed length max. 770mm Pressplattengrösse / Press plates size 290 x 220 mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Year of construction: 1998, machine/vehicle number: 106026, Horizontal stack delivery with pressing and marking device Heidelberg SBP 46.D + MKE.DYear 1998 - Serial-No. 106026/98-263536 Bodpsh Axhdefx Afkewn Sheet size min. (width × length) 120 × 100mm Sheet size max. (width × length) 460 × 300mm Product thickness max. 4mm Pile length 800mm Pressing force 8,000 N Infeed height 360-960mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 31X8030, Mold simulation platform. Manufacturer: STÄUBLI, Type: K8540019, Year: 2011, Serial No.: 31X8030, 2-piece, sliding elements, hydraulic quick-clamping device, quick-change system check (electric/pneumatic/hydraulic), safety light curtains, switch and control cabinets, programming terminal, external hydraulic power units. Mold size 2500x1800mm. Mold inspection platform. Bsdpfoyh Ryajx Afkown

Condition: as good as new (ex-display), Year of construction: 2022, Stierli bender 120HE horizontal press Horizontal bending machine, manual control with angle fine adjustment. Very universal, for bending flat steel, sheet, round steel, profiles, tubes angular or round, forming tools and easy fixing of own tools or special tools, + straightening as straightening press. Bending pressure 12 tons tool height 130 mm Stroke 0-170 mm stepless Bjdsflc R Depfx Afkjwn Bending capacity 130x12 mm S235 Straightening performance light straightening work Pipe bending 3/8"-11/2" Demonstration machine year 2022 incl. hand and foot pedal Machine as good as new

Condition: good (used), functionality: fully functional, pressing force: 160 t, stroke length: 500 mm, operating speed: 30 mm/s, reverse speed: 40 mm/s, table width: 850 mm, table height: 780 mm, throat depth: 400 mm, oil tank capacity: 210 l, total length: 3,370 mm, total width: 1,730 mm, total height: 1,480 mm, overall weight: 6,500 kg, installation height: 400 mm, pressing speed: 3 mm/s, Equipment: documentation/manual, Hydraulic horizontal box press PYXWM-160. Manufactured by WMW VEB Dessau - 1978. The machine has been overhauled. Ready to work. Max. pressing force 160 tons. Piston stroke 500 mm. Piston speed: Forward 30 mm/sec Pressing 2.5 mm/sec Backward 40 mm/sec Height from base to center of piston 260 mm. Machine frame height 780 mm. Base length from support tool 600 mm. Support tool length 520 mm. Max. clamping width 1730 mm. Working clamping width 400 mm. Support tool height 400 mm. Support tool spacing min-max 240-1100 mm. Dimensions: Length 3370 mm. Width 1730 mm. Height 1480 mm. Frame width 700 mm. Engine power 11 kW. Oil tank capacity 210 liters. Bjdowndnuspfx Afkswn

Condition: excellent (used), Year of construction: 2002, functionality: fully functional, pressing force: 15 t, bale width: 700 mm, bale height: 700 mm, bale weight: 220 kg, input voltage: 400 V, power: 4 kW (5.44 HP), empty load weight: 2,700 kg, Manufacturer: Borg Baling Company Type: S-15KK Year of production: 2002 3x400V, 4kW, 14.5A Compression force: 15t Net weight: 2.7 t Bale max. sizes 700x700x1000 mm weight of a bale: ca 120 – 220kg Bwodpsh Dy Rfefx Afken Wide Range of Used Machinery, Industrial Equipment

Condition: new, Year of construction: 2025, Hydraulic horizontal bending and straightening press - Fabrikat Zopf - Model T 1000 - Multiprogramming of 99 programs each 16 steps - hydraulic pressure 100 to. - length of stroke 300 mm - bending speed adjustable - max. working speed 10 mm/sec. - return speed 20 mm/sec. - hydraulic pressure adjustable - maximum bending high 300 mm - motorcapacity 7,5 KW - 400 V 50 hz 3 ph. - working height 940 mm - closed table - replaceable wear plate - weight 2100 kg - bending capacity: flat material max. 300x34 mm at Vmax Bwsdoxpf R Dspfx Afken round tube 3/8" - 3" gas pipe

Condition: new, Year of construction: 2023, Horizontal bending machine AH 40 - ZOPF - with semi-automatic control - hydraulic pressure 40 to. Bwedpsqvm Uksfx Afksn - length of stroke - bending speed adjustable - max. working speed 10 mm/sec. - return speed 20 mm/sec. - hydraulic pressure adjustable - maximum bending high 250 mm - motorcapacity 3,0 KW - 400 V 50 hz 3 ph. - working height 900 mm - closed table - replaceable wear plate - weight 950 kg - bending capacity: flat material max. 150x22 mm round tube up to 60 mm

Condition: new, Year of construction: 2025, Hydraulic horizontal bending and straightening press - Fabrikat Zopf - Model T 800 - Multiprogramming of 99 programs each 16 steps - hydraulic pressure 80 to. - length of stroke 300 mm - bending speed adjustable - max. working speed 10 mm/sec. - return speed 20 mm/sec. - hydraulic pressure adjustable Bwjdpod A Nc Dofx Afkjn - maximum bending high 300 mm - motorcapacity 7,5 KW - 400 V 50 hz 3 ph. - working height 940 mm - closed table - replaceable wear plate - weight 2100 kg - bending capacity: flat material max. 300x32 mm at Vmax round tube 3/8" - 3" gas pipe

Condition: new, Year of construction: 2023, Horizontal bending machine AH 20 with backgauge - ZOPF - with semi-automatic control - hydraulic pressure 20 to. - length of stroke - bending speed adjustable - max. working speed 10 mm/sec. - return speed 20 mm/sec. - hydraulic pressure adjustable - maximum bending high 250 mm - motorcapacity 2,2 KW - 400 V 50 hz 3 ph. - working height 900 mm - closed table - replaceable wear plate - weight 950 kg - bending capacity: flat material max. 150x12 mm Bedpjwyt Tqefx Afkown round tube up to 48 mm