Used Bevel Gear Tester for sale (7,194)

Condition: good (used), max. wheel diameter 1600 mm gear width 250 mm max. module 30 min. module 8 range of tooth size 58 mm tooth width 250 mm weight of the machine ca. 42,3 t dimensions of the machine ca. 4,45 x 6,00 m - Cone spacing in mm. for spiral angle 30° minimum: 150 maximum: 800 - Taper angle, in degrees minimum: 5 maximum: 85 - Tooth angle minimum: 0° maximum: 45° - Number of teeth to be cut Pgedsu Dbucepfx Aa Dok minimum: 10 maximum: 150 The machine is complete, fully functional and in good condition. Equipment / accessories: - complete set of change wheels - 4 pcs. cutter heads - various milling cutters - Operating instructions in English

Condition: used, Year of construction: 1996, functionality: fully functional, machine/vehicle number: 25734, Equipped with: Fanuc 150MB Control Hydraulic Chucking Work Spindle Large Bore Work Spindle #80 Taper Stock Divider Helical Motion Modified Roll Hansen Coolant Chiller & Filtration Coolant Tank & Pumps Chip Conveyor Chip Hopper Reven Mist Collector Hydraulic System Transformer Cutter Bolt Work Light Operator Platform Hand Tools Documentation Specifications: Extreme Ratio: Face Milling: 10:1, Face Hobbing: 10:1 Full Depth: Maximum: Face Milling:1.25" (31.75mm), Face Hobbing: 0.93" (23.50mm) Face Width: Maximum: Face Milling:6.00" (152.00mm),Face Hobbing: 3.00" (76.20mm) Range of Tooth Numbers: 1-300 Inclusive Gear Pitch Diameter, Maximum: 1000 mm (39.37") Cutter Size, Maximum: 18" (diameter) Face Milling Cutter Size, Maximum: 350 mm (radius) Face Hobbing Root Angle Range (B-Axis) 5 deg.to 90 deg., Face Hobbing:5 deg. to 90 deg. Machine Center to Work Spindle Face:9.00"Fixed, 229mm (Fixed) Pgsdpfjxaqa Sox Aa Dok A-Work Spindle: 0 to 67 RPM, 0 to 333 RPM B-Swinging Base: 0 to 30 deg./sec, N/A C-Cutter: 0 to 500 deg., Same X-Horizontal: +/-305mm (+/-12") Y-Vertical: +/-305 mm (+/-12") Z-Sliding Base: -25/+700mm (-1/+28") B-Root Angle: -5 Degree/+90 Degree Diameter of Taper Hole at Large End: 8" (#80 Taper) to 6" (#60 Taper) Taper Per Foot:3/4", Same Depth of Taper Front:6", 152.40 mm Depth of Bore: 678 mm (26.7") Diameter of Taper Bore: 140 mm (5.5") Diameter Through Spindle of Hole:7.125", 180.98 mm MACHINE DIMENSIONS: Length x Width:233"x 209", 5920 mm x 5310 mm Height: 129", 3280 mm Weight: 65,000 lbs., 29,484 kg

Condition: used, Year of construction: 1977, machine/vehicle number: 19909, Equipped with: Index Plate Geneva Cam Cutter Body Hydraulic Work Clamping Coolant Pump & Tank Chip Conveyor Additional Cutter Bodies, Index Plates & Geneva Cams Available Specifications: Minimum Outside Cone Distance: 2.75" Maximum Cone Distance: 10" Maximum Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 Deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 15.6 to 87.7 RPM Feeds (seconds/tooth): 5 to 34.3 Pedpfx Aaexdfazs Degk Main Motor: 10hp, 1800 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approximate Floor Space: 118" x 86.5" Needed Overall Height: 70" Approximate Net Weight: 18,820 lbs Shipping Weight Boxed for Export: 20,500 lbs

Condition: used, Year of construction: 1973, machine/vehicle number: 24109, Equipped with: Pedpfx Ajxdfa Uea Dogk Stock Divider Hydraulic Work Clamping Chip Conveyor Cutter Clamping Bolt Index Plate Change Gears Hydraulic System Coolant System Specifications: Min. Outside Cone Distance: 2.75" Max. Cone Distance: 10" Max. Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 6.8 to 16.5 RPM Feeds (seconds/tooth): 3 to 9 Main Motor: 5hp, 900 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approx. Floor Space: 118" x 86.5" Needed Overall Height: 70" Approx. Net Weight: 16,000 lbs Shipping Weight Boxed for Export: 17,000 lbs

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle Pgjdpfertrzdsx Aa Dek (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: good (used), gear diameter: 508 mm, total height: 1,780 mm, total length: 2,990 mm, total width: 2,200 mm, MODEL 610 GLEASON GEAR ROUGHER/FINISHER Equipped with: Hydraulic Workholding Pendant Control Chip Conveyor Index Plate Geneva Cam Change Gears Hydraulic System Coolant System Manuals Specifications: Psdpfxjrtryks Aa Dogk Maximum Gear Pitch Diameter: 20" Cutter Diameters: 9", 10.5", 12",14",16", 18" Whole Depth: 1.250" Root Angle: 60 to 80 deg. Face Width: 3.0" Extreme Ratio (Minimum): 2.25 to 1 Number of Teeth: 20 to 75 Diameter of Taper Hole at Large End: 3-27/64" Cutter Speeds (Per Minute) for Roughing: 15.6' to 87.7' Feeds (Seconds Per Tooth) for Roughing: 3 to 35 Cutter speeds (Per Minute) for Finishing: 6.8' to 20.5' Feeds (Seconds Per Tooth) for Finishing: 3 to 9 Floor Space: 118" x 86.5" x 70" H Weight: 17,500 lbs.

Condition: good (used), Year of construction: 1985, functionality: fully functional, overall weight: 1,450 kg, total length: 1,620 mm, total width: 930 mm, total height: 920 mm, gear ratio: 200:1, torque: 21,400 Nm, shaft diameter: 160 mm, power: 14 kW (19.03 HP), 6 industrial helical bevel gearboxes from Flender / ASUG / Penig TGL 21815 maximum continuous torque: 27280 Nm Gear ratio: i= 200:1 max. power: 14 kW at 1250 rpm 20 kW at 1400 rpm Oil filling: 170 kg Weight: 1450 kg Shaft diameter d1: 40 mm Shaft diameter d2: 160 mm Pgsdpfxorvg N Dj Aa Dsk Shaft height h1: 500 mm Total height h2: 925 mm Also available sprocket 48B3 17 Z and 48B3 35 Z

Condition: excellent (used), Electrical installation tester from the renowned German manufacturer Gossen Metrawatt The PROFITEST MXTRA model is designed for professional measurement of electrical installations and safety inspections. The device is used by electricians, service technicians, and for routine installation inspections. ⸻ TECHNICAL SPECIFICATIONS Manufacturer: Gossen Metrawatt Model: PROFITEST MXTRA Supply voltage: 230 V Measurement category: CAT III 600V, CAT IV 300V Professional electrical installation tester ⸻ INCLUDED IN THE SET PROFITEST MXTRA tester measurement cable adapter carrying bag Pgedjywcr Djpfx Aa Dek The exact set is shown in the photos ⸻ APPLICATIONS electrical installation measurement safety testing installation inspections electrical service ⸻ CONDITION used visually in good condition

Condition: excellent (used), Electrical safety tester from the renowned German manufacturer Gossen Metrawatt The SECUTEST Pro model is designed for testing electrical devices in accordance with the IEC 62353 standard. The set includes several devices along with measuring leads and carrying bags. TECHNICAL DETAILS Manufacturer: Gossen Metrawatt Model: SECUTEST Pro Standard: IEC 62353 Power supply: 230 V Professional tester for electrical device safety SET INCLUDES Several testers Pgedpeywcrwefx Aa Dsk Measuring cables Adapters Carrying bags Exact condition as shown in the photos APPLICATIONS Testing of electrical devices Service and maintenance Safety inspections Medical and industrial use CONDITION Used Visually in good condition Technical condition not fully checked IMPORTANT Sale as a set as shown in the photos No additional accessories except those pictured SHIPPING

Condition: used, Chroma Type: ATE 17020 The Chroma 17020 is a highly professional, modular test system for lithium-ion & other battery pack qualification. Particularly strong in: - Lifetime testing, BMS verification, and validation of complex charging cycles - High energy recovery – up to 85% efficiency - Flexible expansion through numerous channels or higher current ranges - Enterprise deployment with extensive safety features & data persistence Technical data – Chroma ATE 17020 PTS Feature Specification Model: Chroma ATE 17020 PTS System type: Regenerative battery pack test system (charge/discharge test) Channel output: 600 W to 60 kW (modular and scalable) Total output: Up to 600 kW (depending on configuration) Voltage range: 20 V / 60 V / 100 V / 200 V / 500 V Current per channel: Depending on module: from a few amps up to >300 A per channel Parallel operation: Yes, for higher current up to 2,600 A Current and voltage accuracy: ±(0.05% of reading + 0.05% of range) Power accuracy: ±0.1% Transition time (charge/discharge): < 50 ms Sampling rate (measured data): up to 50 kHz (with BatteryPro) Data logging: Cyclic, 10 μs – 1 s / memory for 60 min power failure Pgjdowwrxajpfx Aa Dsk Test modes: CC, CV, CP, CC-CV, DCIR, pulse, drive cycle, dynamic profiles Number of channels: Up to 60 channels (expandable) Communication: CAN, S-Bus, Ethernet, USB Software: Chroma BatteryPro (test programming, real-time monitoring) Protection functions: OVP, UVP, OCP, UCP, OTP, reverse polarity, wire loss, delta V/I, etc. Energy recovery: Yes – up to 85% energy efficiency, grid-friendly (THD < 5%) Cooling: Fan cooling, low waste heat due to energy recuperation Temperature monitoring: Optionally integrable, range 0–90°C ±2°C Dimensions & weight: Depending on configuration (e.g. 19″ rack, approx. 300 kg) Mains connection: 3-phase, 400 V AC (depending on model) Applications: E-mobility, battery development, quality assurance, cell research Weight: approx. 455 kg Condition: used Scope of delivery: (See picture) (Specifications and technical data are subject to change and errors excepted!) If you have further questions, we are happy to assist you by phone.

Condition: new, Year of construction: 2026, -Tfon Bevel Wizard® Linear. -Precision Beveling for Linear & Non-Linear Applications. -The TFON Bevel Wizard® Linear is a high-performance beveling solution designed to deliver exceptional accuracy on both straight and contoured sheet edges. Engineered with flexibility at its core, it features an advanced Trace Tracking System that automatically adjusts to variations in material thickness and geometry—ensuring precise and consistent edge processing even for complex parts -Key Features 🔹 Advanced Trace Tracking System: Intelligently detects and adapts to diverse edge shapes and contours in real time. 🔹 Wide Beveling Range: Adjustable bevel angles from -30° to +80°, ideal for a broad range of applications. Pedpfx Aajrt Tpns Dsgk - Optimized for Large Workpieces Capable of processing materials up to 12,000 mm in length and 100 mm in thickness. - Industrial-Grade Durability: Built to last with a solid 10,000 kg frame for long-term reliability. 🔹 Superior Surface Finish: Delivers a high-quality finish with a consistent Emery Band Rotation Speed of 30 m/min and a Ø135 mm contact wheel. -Technical Specifications: Beveling Angle Range: -30° to +80° -Material Thickness: 4 – 100 mm -Minimum Material Width: 250 mm Minimum Material Length: 250 mm Maximum Material Length: 12,000 mm Part Feed Speed: 1.5 – 5 m/min Part Completion Speed: 3 meters/day Maximum Part Indentation: Ø400 mm Emery Band Rotation Speed: 30 m/min Contact Wheel Diameter: Ø135 mm Emery Band Drum Diameter: Ø400 mm Machine Weight: 10,000 kg Engineered for precision. Built for performance. Designed for industrial excellence Tfon Bevel Wizard® Linear — Where Accuracy Meets Efficiency.

Condition: excellent (used), functionality: fully functional, Year of construction: 2002, operating hours: 48,651 h, Mazak Space Gear-510 MKII 2.5 kW Podpfx Aaowqr Tdj Dogk Year of manufacture December 2002 - after renovation!!! Very good condition! Meter reading 48651 hours Operating system Fanuc L-64

Condition: excellent (used), functionality: fully functional, Year of construction: 2007, operating hours: 41,417 h, Mazak Hyper Gear 510 4.0 kW Year of production February 2007 Meter reading 41417 hours MAZATROL operating system very good condition Technical data of the MAZAK HYPER GEAR 510 laser cutter - laser power: 4 kW - feeds in the X/Y/Z axes: 3070/1545/100 mm - dimensions of the work table (length x width): 3000 x 1500 mm - maximum weight of the workpiece: 930 kg - maximum dimensions of the workpiece (length x width x height): 3050 x 1525 x 25 mm - laser type: CO2 Podpewqr Twsfx Aa Degk

Condition: good (used), Geared motor, electric motor, electric geared motor -Manufacturer: Ametek, geared motor Pgsdpfey Ecryex Aa Dok -Transmission: with toothed belt pulley -Speed: rpm -Engine: Ametek 18323 6330620005 -Voltage: 220/240V -Dimensions: 125/85/H160 mm -Weight: 1.7 kg

Condition: good (used), Mechatronic drive system, gearbox, spur gear gearbox, bevel gearbox, worm gearbox, Movegear Pgsdpfxjy D I Hye Aa Dsk -Gearbox: Angle gearbox -Translation: 31 : 1 -Shaft: Ø 20 x 50 mm / Ø 30 x 25 mm -Dimensions: 280/270/H210 mm -Weight: 24.5 kg

Condition: good (used), Flat geared motor, geared motor, electric motor, electric geared motor, flat geared motor, flat geared motor -Manufacturer: Nord, flat geared motor -Type: SK 2080A-80 L/4 i= 10.27 -Speed: 135 rpm Pgjdpoy D Hupjfx Aa Dsk -Engine: Type SK 80 L/4 -Power: 0.75 kW -Hollow shaft: Ø 30 x 100 mm -Protection class: IP54 -Dimensions: 340/310/H215 mm -Weight: 22.7 kg

Condition: good (used), Flat geared motor, geared motor, electric motor, electric geared motor, flat geared motor, flat geared motor Pgodpfx Aaet E D Exe Dsk -Manufacturer: Nord, flat geared motor -Type: SK 2080A-80 L/4 i= 10.27 -Speed: 136 rpm -Engine: Type SK 80 L/4 -Power: 0.75 kW -Hollow shaft: Ø 30 x 100 mm -Protection class: IP54 -Dimensions: 320/290/H205 mm -Weight: 20 kg

Condition: used, Year of construction: 1997, Technical details: max. module: 7 weight of the machine ca.: 5 t worm grinding diameter: 280-350 mm width of grinding worm: 84-104 mm min. number of teeth: 6 max. number of teeth: 600 max. top circle diameter: 360 mm max. workpiece weight: 60 kg Pgodpfx Aox Aq Egoa Djk without filter *

Condition: used, Year of construction: 1963, Technical details: max. wheel diameter: 900 mm max. module: 10 weight of the machine ca.: 8200 kos. hob dia. - max.: 190 mm cutter length max.: 320 mm milling spindle speeds (infinitely variable): 13-80 U/min workpiece length - max.: 750 mm max. workpiece diameter: 150 mm Counter holder milling mandrel is missing Pgedsvkpu Hspfx Aa Dsk *

Condition: used, Year of construction: 2007, max. wheel diameter 400 mm Pjdpjy D T Sujfx Aa Dogk workpiece dia. 36-300/400 mm axis distance 135-290 mm spindle turning speed - stepless 3000 1/min dist. between centers 100-550 mm Control Siemens 840D weight of the machine ca. 4000 kg dimensions of the machine ca. 2000x3055x2788 mm Test method: - Single flank rolling test - Double flank rolling test - Structure-borne noise test - Heli testing in two-flank contact. Features: - Use of up to 6 test slides - Highest testing accuracy and repeatability - Machine table with workpiece drive - Swiveling pneumatic unit - Spray oil lubrication (type: Vogel) - Oil mist extraction (type: Elbaron)

Condition: used, Year of construction: 2010, gearing type: automatic, color: other, Year of manufacture: Apr 2010 Podpfxoy Enkbe Aa Djgk Axle 1: left 8 mm righ8 mm Axle 2: left 8 8 mm right 8 8 mm Axle 3: left mm right mm

Condition: excellent (used), Gear Hobbing Machine LORENZ E16 Suitable for: - Spur gears - Helical gears - Worm gears with radial feed - Worm gears with tangential feed - Internal gear rings Max. workpiece diameter: 1,600 mm Max. workpiece diameter with tailstock: 1,100 mm Max. gear width: 660 mm Max. module with hob cutter: 16 mm Max. module with disc-type cutter: 18 mm Max. module with finger cutter: 25 mm Max. distance table center – cutter center: 950 mm Min. distance table center – cutter center: 50 mm Pgjdpfx Ajy Hqnrsa Dok Max. vertical traverse: 740 mm Table diameter: 1,250 mm Table bore diameter: 250 mm Bore depth: 400 mm Mandrel table diameter: 90 mm Electrically overhauled and equipped with SIEMENS SIMATIC OP7. Manuals available. 1. Including change gears 2. Including milling arbors 3. Including finger milling head 4. Including tangential milling head

Condition: good (used), Year of construction: 2020, Geared motor, electric motor, electric geared motor, worm geared motor -Manufacturer: Dalian NET, worm gear motor -Gearbox: Type NMRV 1:10 -Speed: 143 rpm -Engine: Type Y2-90S-4 -Power: 1.1 kW -Protection rating: IP54 -Shaft: Ø 28 x 110 mm -Dimensions: 440/220/H260 mm Pedpfx Aasy Ai T Es Djgk -Weight: 24 kg

Condition: good (used), Year of construction: 2018, Geared motor, electric motor, electric geared motor, worm geared motor -Manufacturer: Dalian NET, worm gear motor -Gearbox: Type NMRV 050 1:100 -Speed: 9 rpm Pedpoy Ai N Hofx Aa Dsgk -Engine: Type Y2-802-6 -Power: 0.55 kW -Protection rating: IP55 -Shaft: Ø 25 x 90 mm -Dimensions: 390/200/H250 mm -Weight: 18.8 kg

Year of construction: 2012, condition: used, max. wheel diameter 180 mm gear width ca. 220 mm max. module 3 / 5 mm Control Siemens 840D sl max. radial velocity 5000 mm/min max. workpiece diameter 180 mm table rotation speed 800 U/min table diameter 145 mm axial travel 250 mm mm axial travel 300 mm Podpoymf Daofx Aa Degk clamping force max. 13 kN swivelable +/- 45 ° drive capacity 23 kW turning speeds 6000 U/min diameter of tools max. 90 mm tool clamping length max. 211 mm module hobbing max. 3 module profile milling max. 5 tangential speed max. 7500 mm/min weight of the machine ca. 9,5 t dimensions of the machine ca. 4,5 x 3,5 x 2,7 m Equipment / Accessories: - The machine is equipped for dry milling. - workpiece magazine - parallel gripper: - workpiece weight form-fit max. 15 kg - workpiece length max. 400 mm