Used Bottle Washer for sale (2,816)

Condition: used, Year of construction: 2004, Overview Krones Lavatec KES bottle washer from 2004, rated at 11,000 bottles per hour. The machine cleans glass bottles in a juice and soft drink bottling line and is still installed and under power. Technical data - Manufacturer: Krones - Model: Lavatec KES - Year of manufacture: 2004 - Output: 11,000 bottles/h - Containers: glass bottles - Electrical supply: 380 V, 3 phases, 50 Hz, 70 A connected load Condition Used, still installed and under power. The line produces until shutdown on 20 November 2026. Inspection on site is possible. Tsdpfxe Agpqws Abuod Availability Available after shutdown on 20 November 2026. Location: Belgium.

Condition: used, Year of construction: 1993, Overview This Klinger Serpende bottle washer was built in 1993 for cleaning returnable glass bottles in caustic baths. Its nominal output is 7,000 bottles per hour on 2 L bottles, adjustable between 4,000 and 8,000 bottles per hour. The machine works with plastic bottle carriers, 16 bottles per row, and takes bottles up to 95 mm in diameter. Construction is stainless steel, controlled by a Siemens SIMATIC S5 PLC with an operator panel at the machine. Suitable for water and soft drink lines running returnable glass. Technical data - Manufacturer: Klinger - Model: Serpende - Year of manufacture: 1993 - Machine type: bottle washer for returnable glass bottles, caustic bath cleaning - Nominal output: 7,000 bottles/h (2 L bottles) - Control range: 4,000 - 8,000 bottles/h - Bottle diameter: max. 95 mm - Bottle carriers: plastic, 16 bottles per row Todj Agac Ropfx Abujd - Carrier rows: 117 in total, 100 loaded (1,600 bottle pockets) - Cycle time: 8.2 s - Total treatment time: 16 min - Pre-soak: 3.0 min holding time, 2.6 min treatment time - Caustic bath: 7.1 min holding time, 5.0 min treatment time - Cooling: 3.0 min holding time, 2.1 min treatment time - Material: stainless steel - Dimensions: approx. L 9,000 x W 3,300 x H 3,050 mm - Weight: approx. 19,000 kg Equipment - Plastic bottle carriers for bottles up to 95 mm diameter - Siemens SIMATIC S5 control in a separate control cabinet - Operator panel with keypad and emergency stop - Bottle infeed and discharge Condition Used. The machine is already dismantled and in storage. Availability Immediately. Location: Italy. Preparation and loading by the seller, EXW loaded.

Condition: used, Year of construction: 2024, Overview The bottle washer was previously used in a brewery. Due to the low number of operating hours, the machine is in very good condition, like new. It was replaced, as the previous owner wanted to run bottle formats, which did not fit this machine. All basins and the machine body are made of stainless steel. The machine is already disassembled and dry stored, so that it can be easily loaded and transported. The machine comes with 12months warrantee. Tech Specs: - Capacity: 9,500 bph - Cell Pitch: 95 mm - Bottles per row: 25 - Dimensions + Weights: Housing: 7,162 x 2,740 x 2,500 mm / 18,806 kg Ready for operation with attachments: 7,162 x 3,540 x 2,730 mm / 31,563 kg - YOM 2024 - Formats: - 0,25l - 0,33l - 0,5l - 0,75l Tedpevrfivefx Abued The Machine in Detail / Equipment Features: - Heated by steam - Pre Cleaning and removal of residual liquids by pulsed rinsing prior to washing - CE certified - Chemical Dosing Pumps - Machine data sheet included - High pressure pre rinsing - Rotating Spray nozzles - Single End Machine - Label discharge rear right - Finger discharge + finger feed - Bottle cells made of plastic - Concentration measurement - NaOH supply liquid - Sectional view arrangement of baths - Spindles SST - 24 volt control voltage - Control Siemens S7 - Regularly maintained - Full machine body in SST - Vapor Discharge - Machine dismantled, ready to ship - Automated machine Startup

Condition: used, Offered for sale is an industrial bottle washing machine with a multi-stage cleaning system. Rated capacity: 2000bottles/h. Bottle volume: 0.2-1.0liters. Bottle diameter: 58-88mm. Bottle height: 140-330mm. Total bottle rows: 61. Bottles in the machine: 770 units. Cycle time: 19.3846sec. Total transit time: 19.71min. Caustic contact time: 11.95min. Max. water consumption: 1.0m³/h. Equipped with bottle infeed and discharge, weak caustic bath, multi-stage spray systems for caustic solution, hot, warm and fresh water, and label discharge. Empty weight: approx. 6500kg. Overall dimensions X/Y/Z: approx. 5050mm/3139mm/2450mm. Height including spindles: 2600mm. Inspection possible by arrangement. Tjdo Ad Nqhopfx Abujd

Condition: used, Year of construction: 1995, Overview  This bottle washer was built in 1995 by Swiss manufacturer PAC. The machine is out production and be viewed in person in our warehouse. Techn. Details - Capacity:  - 6,000 bph - Min/ Max: 3,000 bph – 6,300 bp - Bottle type: 0,5L, Euro, NRW, incl. Set of parts for 330ml vichy bottle - Bottles per row: 12 Todsvl Huaopfx Abujd - Bottles in the machine: 1,080 - Bottle cell carriers: 96 - Dimensions:  - Length: 6,000 mm - Width: 1,545 mm - Height: 2,175 mm (without feet) - Weight: approx. 5,800 kg - Water consumption: 3,6 m³/h - Heat consumption 80°C: 480 kJ/ h x 1000 - Electrical consumption: 11 kW - Incl. Spare parts - Motors for rear and front drive - Bottle cell carriers - Wear parts - Machine body fully in stainless steel - All hot zones with 5cm insulation - Label extraction belt - Heat exchanger in stainless steel for low pressure steam 116°C-120°C at 0,7 - 1 bar - Self cleaning spray tubes in stainless steel

Condition: used, Year of construction: 2010, Overview   This ARCADE GEL 6 bottle washer was built in 2010 by the German manufacturer GM Gera. The machine is still in operation and can be inspected in person at any time. The ARCADE GEL 6 is fully functional and must be replaced due to an increase in performance.   Technical details   Nominal output: 33,000 bph   Control range: 13,200 - 36,300 bph   Chain pitch: 169 mm   Cell pitch: 110 mm   Bottle cells per row: 30 pieces   Total bottle cells: 7,860 pieces   Bottle cells, loaded: 7,680 pieces   Consumption  Compressed air: 1m³   Steam (operation): 489 kg/ h   Steam (heating): 4,430 kg/ h   Electrical power: 48.4 kW   Water: 7.35 m³/ h   Bath volume   Pre-soak: 2,263 l   Pre-caustic: 7,240 l   Caustic 1: 31,755 l   Caustic 2: 350 l   Hot water 1: 350 l  Hot water 2: 350 l   Cold water: 350 l  Tjdpfxet Ul Exo Abued

Condition: used, Year of construction: 1995, Overview The bottle washer "Sirio 7" from the German manufacturer MAG was built in 1995. Maintenance was carried out regularly by MAG. The machine can be inspected and tested in person. Technical details  Capacity up to 7,000 bph Bottle cells for 1.0 liter bottles (smaller bottles can also be used, but additional insertion plates are required) Diameter of bottles: 78 - 90 mm Bottle height: 288 - 310 mm Bottle cells per row: 10 Dimensions (LxWxH): 7,880 mm x 3,045 mm x 3,325 mm Empty weight: 14,300 kg Full load weight: 25,600 kg Installed power: 20.85 kW Heating system: Steam 3 bar Tedpstrbrqofx Abued

Condition: used, Year of construction: 2013, Overview The bottle washer was manufactured by the German company Krones in 2013 and put into operation in 2014. It has been serviced annually. In addition, tenside lye cleaning and spare parts can still be purchased. DISMANTLING INCLUDED. Technical data  Capacity: 66,000 bph Maximum bottle diameter 69 mm Set up for the following formats:  Vichy 0,33l Long-Neck 0,33l Long-Neck 0,5l NRW 0,5l  Steinie 0,33l Tedpfx Absl Hx Enjujd

Condition: used, Year of construction: 2005, Overview The bottle washer was previously used in a mineral water factory. Due to the good maintenance, the machine is in good condition. All basins and the machine body are made of stainless steel. The machine is still working and will be free in early 2027, when the complete line is replaced. Tech Specs - Capacity: 15,500 bph - Cell Pitch: 95mm - Bottles per row: 16 - Dimensions + Weights: Housing: 8350 x 1,860 x 2,990 mm / 21,750kg Ready for operation with attachments: 8,700 x 3,560 x 3,330mm / 37,639kg - YOM 2005 - Formats: - 0,5l - 0,75l The Machine in Detail / Equipment Features - Heated by steam - Pre Cleaning and removal of residual liquids by pulsed rinsing prior to washing - CE certified - Chemical Dosing Pumps - Machine data sheet included Tedpfx Aezbha Hsbusd - Rotating Spray nozzles - Single End Machine - Label discharge rear right - Label press mounted to the machine - Finger discharge + finger feed - Bottle cells made of plastic - Concentration measurement - NaOH supply liquid - Sectional view arrangement of baths - Spindles SST - Control Siemens S7 - Regularly maintained - Full machine body in SST - Vapor Discharge

Condition: used, Year of construction: 2002, machine/vehicle number: LV46, Used R. BARDI nilo 2-20R bottle washer 20000 BPHTechnical Specifications & Performance DataThe R. Bardi Nilo 2-20R is a linear bottle washer designed for returnable glass bottle handling in bottling and industrial packaging operations. Manufactured in 2002, this machine is engineered to support high-throughput washing processes within a used bottling line, combining bottle cleaning performance with format flexibility.Manufacturer: R. BardiModel: Nilo 2-20RYear of manufacture: 2002Maximum output: up to 20,000 bottles/hourConfiguration: LinearOperating pressure: 6 barCompatible formats: 0.25L, 0.33L, 0.5L and 0.75L bottles, plus other formatsContainer material: GlassAdvanced Automation & Control SystemsThis bottle washing machine is intended for continuous industrial operation, with a linear layout that supports controlled bottle transport through the washing process. Its design is suitable for integration into automated beverage production environments where reliable handling of returnable bottles is required. The stated 6 bar operating pressure should be considered when assessing the compressed-air infrastructure of the installation.Format-specific adjustments are important for maintaining stable bottle movement and effective cleaning performance. Before commissioning, operators should verify the compatibility of guides, carriers, infeed and discharge interfaces with the glass bottle formats to be processed.Production Line Integration CapabilitiesThe Nilo 2-20R is suited to the washing stage of a returnable glass bottle production line. In a typical used bottling line, it is positioned after bottle unloading, decrating and decapping operations, and before empty-bottle inspection, filling, capping, labeling and secondary packaging.The machine processes returnable glass bottles with paper labels, paper and aluminum labels, as well as unlabeled bottles. This capability makes it relevant for industrial packaging lines handling recovered containers that require preparation before refilling. The supported 0.25L, 0.33L, 0.5L and 0.75L formats provide flexibility for beverage production applications using multiple bottle sizes.Machine Condition & Maintenance HistoryThe machine is currently in operation and can be inspected while running in production until April 2027. Its operating condition can be verified directly before purchase. The stated commercial condition is as inspected and accepted.For a second hand bottle washer, an on-site operational inspection provides an opportunity to assess bottle flow, washing-cycle performance, format handling and integration requirements against the intended production line configuration.Operational Performance & VersatilityDesigned for returnable glass bottle applications, this R. Bardi bottle washer supports the preparation of labeled and unlabeled containers for reuse. Washing equipment of this type is a central element in returnable bottling operations, helping remove labels and prepare bottles for downstream inspection and filling.The linear machine arrangement supports orderly bottle mov... Tsdez E Dgyopfx Abuod

Condition: used, Year of construction: 1999, Overview The bottle washer was previously used in a brewery. Due to the complete reconditioning in 2005 and continuously maintentance, the machine is in very good condition. All basins and the machine body are made of stainless steel. The machine is already disassembled and dry stored, so that it can be easily loaded and transported.  Tech Specs: - Capacity: 6,700 bph - Cell Pitch: 102 mm - Bottles per row: 10 - Dimensions + Weights: Housing: 7,200 x 1,300 x 2,850 mm / 13,500 kg Ready for operation with attachments: 7,790 x 3,450 x 2,950 mm / 20,000 kg - YOM 1999 - Formats: - 0,33l - 0,5l The Machine in Detail / Equipment Features: - Heated by steam - Pre Cleaning and removal of residual liquids by pulsed rinsing prior to washing - CE certified - Chemical Dosing Pumps - Machine data sheet included - High pressure pre rinsing - Rotating Spray nozzles - Single End Machine Todpfx Aowg E D Isbued - Label discharge rear right - Finger discharge + finger feed - Bottle cells made of plastic - Concentration measurement - NaOH supply liquid - Sectional view arrangement of baths - Spindles SST - 24 volt control voltage - Control Siemens S7 - Regularly maintained - Full machine body in SST - Vapor Discharge - Machine dismantled, ready to ship - Automated machine Startup

Condition: used, Bottle washer, make Krones, type: KES 1-5-190/14-110 R, single-end machine in stainless steel, for 13.200 bph, 14 bottles/row, with 110mm cell pitch, with pre rinsing, presoak bath, caustic soaking and caustic spraying, 4 water spraying (2x warm + 1x cold + 1x fresh water), with headboard disinfection, S7 control, built 1996. L: ~12.500 mm, W: 4.645 mm, H: 3.500 mm, weight: 33.000 kg Todpforxuv Aex Abusd

Condition: used, Year of construction: 2002, Bottle washer, make Krones, type: Lavatec KESK 245/17-120, control range 4.000 - 11.000 bph, for bottles with max diam. 105mm, built 2002, single-end machine, 180 rows of 17 bottle pockets, removed label outfeed in bin, with pre-soak bath water + caustic, 1+2 caustic jetting, 1+2+3 water jetting hot+cold+fresh, for sale. Tedpfx Asrxup Sobujd

Condition: used, Year of construction: 1996, Overview This bottle washer was built in 1995 by Swiss manufacturer PAC. The machine is still in production and be viewed in person. Techn. Details   Capacity:  10,000 bph Min/ Max: 5,000 bph – 13,000 bph Bottle type: 0,5L, Euro, NRW Bottles per row: 10 Bottles in the machine: 1,980 Bottle cell carriers: 204 Dimensions:  Length: 8,100 mm Width: 1,395 mm Height: 2,300 mm (without feet) Weight: approx. 9,210 kg Water consumption: 4,0 - 4,8 m³/h Heat consumption 80°C: 700 - 840 kJ/ h x 1000 Electrical consumtion: 17 kW Incl. Spare parts Motors for rear and front drive Bottle cell carriers Wear parts Tjdpou H R Nnjfx Abusd

Condition: used, Year of construction: 1998, Overview  This bottle washer was manufactured in 1998 by the German company PAC. The CB 14-0,5L-R-7 LII Compact model is a fully automatic returnable glass bottle washer designed for medium-capacity beverage filling lines. With a throughput of 7,500 bottles per hour, it ensures effective cleaning through a multi-stage process using caustic and hot-water baths. The unit has 14,175 operating hours and is in good working condition. Technical data - Capacity: 7,500 bottles/hour - Adjustable speed range: 3,750 – 7,875 bottles/hour - Cycle time: 6.72 seconds - Total treatment time: 11.65 minutes - Bottle formats: Up to Euro-NRW - Bottle rows per carrier: 14 - Bottles inside machine: 1,456 - Bottle carrier trays: 110 - Effective spray times: - Hot lye 8.96 seconds - Lye II 8.96 seconds - Hot water II 8.96 seconds - Hot water I 8.96 seconds - Cold water: 13.44 seconds - Fresh water max.: 8.96 seconds - Utilities - Water consumption: 3.25 – 3.38 m³/h at 60°C - Power connection: 12.0 – 12.9 kW - Thermal energy consumption: 3,528 × 1000 kJ/h - Dimensions Tedpfoxn A S Nsx Abuod - Length with cabinet: 7,020 mm - Width of frame: 1725 mm - Height: 2300 mm

Condition: used, Year of construction: 1993, Overview This Klinger BC 16/1 bottle washer was manufactured in 1993 by the german manufacturer Klinger and is designed for cleaning returnable glass bottles. The machine is made entirely of stainless steel and equipped with modern cleaning, dosing, and control features ensuring reliable operation and excellent hygiene results. The washer is in good working condition. Suitable for multiple glass bottle formats used in beverage filling lines. Technical Data Tsdpfx Abeyb Sxaoued - Manufacturer: Klinger - Type: BC 16/1 - Year of manufacture: 1993 - Application: Returnable glass bottles - Material: Full stainless-steel construction - capacity: 20.000 bottles/h Features - Complete stainless-steel construction - Steam extraction system - Finger infeed and finger discharge - Chemical dosing system - Rotating spray pipe system - Lauer control panel - Conductivity measurement - Stainless-steel filter inserts - Plate heat exchanger - Compatible with standard bottle formats

Condition: used, Year of construction: 2007, Overview This KHS Innoclean single-end bottle washer for returnable glass bottles was built in 2007. It cleans and de-labels empty bottles before filling: bottles are pushed into carrier-basket cells, run on heavy roller chains through a pre-soak, two pre-warming baths, the main caustic soak with under- and over-caustic label flushing, and three water spray zones, then handed back onto the bottle conveyor at discharge. Nineteen bottles run across the machine width in 4,275 cells; output range and design output are given below under Technical data. At design output, total dwell time is 18.7 minutes, including 10.8 minutes of caustic contact. KHS modernised the drive and operator station in 2022: Triple-i-Drive and a capacitive multi-touch panel with RFID login, detailed under Equipment. A KHS manual supplement dated November 2022 covers the upgrade. Technical data - Manufacturer: KHS - Model: Innoclean - Machine type: single-end bottle washer (soaker) - Year of manufacture: 2007 - Drive and control modernisation by KHS: 2022 - Output range: 2,800 - 14,500 bottles/h - Design output: 13,200 bottles/h, 0.75 l glass bottle, 0.68 kg - Bottles across machine width: 19 - Carrier baskets: 225, of which 217 loaded - Cell pitch: 105 mm; carrier chain pitch 169 mm - Bottle diameter: 54.0 - 89.5 mm (plastic cells) - Bottle height: 180 - 340 mm - Bath volumes: main caustic soak 23.0 m³, pre-soaks 0.9 and 1.1 m³, after-caustic 0.3 m³, spray zones 0.4 m³ each - Power supply: 400 V, 50 Hz, TN-S, 113 A nominal, 125 A slow fuse; control voltage 24 V DC - Water consumption: 3.56 m³/h, 270 ml per bottle - Compressed air: 1.0 Nm³/h at 3 bar - Overall dimensions: 11,040 x 4,470 x H 3,438 mm (incl. infeed table) - Conveyor heights: infeed 720 mm, discharge 1,690 mm - Weight approx.: 33.5 t machine, 62.6 t operating - Largest transport segment: 4,410 x 4,100 x 3,370 mm, approx. 7.3 t - Enclosure type 12; CE marked Equipment - Triple-i-Drive: worm gearboxes with individual geared motors, each on its own servo inverter with synchronisation and individual overload protection - Servo-driven infeed and discharge segments with brake motors - Capacitive multi-touch operator panel, graphical interface with component views, RFID card reader - Gearbox monitoring with torque protection - Two pre-warming and main caustic immersion baths, with under- and over-caustic label flushing and bottle base spray-off - Automatic label discharge over a full-width sieve belt with brush take-off - Automatic level control and caustic dosing; sieve tub filtration and after-caustic circuit for long caustic service life - Three water spray zones, internal and external, with rotating fresh-water spray - Vapour extraction and plate heat exchanger Tedpszzz Ivjfx Abuod - Siemens SIMOTION D and SINAMICS drive cabinet - Original KHS documentation: operating manual, 2022 supplement, spare parts list Condition Used, technically complete. Still installed and under power at its production site; photographs and video show it running. Availability Immediately. The machine will be dismantled and relocated to Germany. Viewing by arrangement; dismantling, loading and transport can be quoted on request.

Condition: used, Year of construction: 1993, Overview The GM Gera NAGEMA Arcade DS bottle washer was previously used in a brewery. There it was operated in single-shift operation. Since the sales volume has decreased, the beer of the brewery is now bottled at another location and this bottling line has become available. Due to the low number of operating hours and regular maintenance, the machine is in a very good condition. All basins and the machine body are made of stainless steel. Spare parts, such as bottle cells, are also still available. Furthermore, the main drive shaft, as well as the motor and gearbox were overhauled by SEW in 2018 and the carrier chain was replaced in 2015. The machine is still mounted and can also be demonstrated. Tech Specs: Capacity: 23,000 bph Cell pitch: 85 Bottles per row: 16 Dimensions + weights with attachments: 8640 x 4470 x 1920 mm / 17,900 kg Details: Standard drives Heating with steam Operating side left CE certified Chemistry dosing pumps Machine data sheet Fixed pipe spraying controlled by machine cycle Single-end machine Label discharge rear right Finger discharge + finger feeding Bottle discharge left Bottle cells plastic HMI Lauer Lye concentration measurement 24 Volt control voltage Control S5 (on request conversion to S7) Regularly maintained Water part in VA Fume extraction Sampling taps KSB pumps in VA Plug-in strainers for baths Water meter Conductivity measurement from Endress Additional Equipment: Spare parts included   Tedpfx Abol Hx Adjuod

Condition: used, Year of construction: 2000, operating hours: 15,800 h, Used Bottle Washer KLINGER up to 9600 bph This Bottle Washer handles up to 9,600 bottles per hour. The machine features 20 bottles per row, ensuring a long soaking time and double lye pumps. Constructed entirely of stainless steel, this bottle washer uses a Siemens S7 control system, ensuring reliable and precise operation. Technical Specifications of the Washing System The Used Bottle Washer KLINGER up to 9600 bph includes double heaters and overflow pumps, providing a high cleaning capacity. Consequently, this configuration treats each bottle uniformly, enhancing the efficiency of the washing process. The Siemens S7 control system, furthermore, offers a user-friendly interface via a touch panel, simplifying operational management. Potable Water Treatment Plant Potable water treatment plays a crucial role in the proper functioning of the bottle washer. Hager + Elsässer provides the plant, which includes cation and anion exchangers, a salt container, a pre-filter, and a UV probe. This system processes 5 m³/h, ensuring high-quality water. Additionally, the reverse osmosis (RO) plant delivers a total desalination capacity of 2.5 m³/h, ensuring pure water for the washing process. Electrical Configuration and Control Panels This Bottle Washer features three electrical panels, arranged from left to right, with a Siemens touch panel for centralized control. This configuration allows for accurate monitoring and optimal operational management. In addition, the upper panels handle cooling, with a total residence time of 4.13 minutes and a treatment time of 1.63 minutes. Technical details Bottle cells: width and diameter: height 100 mm. 360 mm spray hole in the base of the cell diameter 20 mm. The bottle cell is not round on the lower insertion side, but flattened , so that even bottles with small diameters can be inserted into the cell without any problems. Bottles from 200 ml to 1,500 ml can be rinsed. The diameter of the bottle mouth must not be smaller than the spray hole in the bottom of the cell, i.e. at least 20 mm. If the bottles are very light, or made of PVC, the spray pressure of the pumps could be reduced using software, so that the bottles are not sprayed out of the cell. Fort PVC bottles the diameter of the bottles should not be smaller than 50 mm, depending on the shape and weight. The higher the weight, the better… PVC bottles do not cause problems because of their shape or diameter, but are usually too light… So your bottles can be easily worked. Treatment and Spraying Details of the Used Bottle Washer KLINGER up to 9600 bph The central panel, on the other hand, manages the spraying times with the following specifications: Spraying soda: 0.5 min. Residual soda: 0.83 min. Hot water: 0.38 min. Warm water: 0.38 min. Cold water: 0.38 min. Tedsxqmrfopfx Abujd Fresh water: 0.

Condition: new, Year of construction: 2026, functionality: fully functional, *All of our products are made with care and covered for 1 year warranty! *Installation and Operator Training FREE • Model: FABO HY-600 • Type: Double Helix Screw Washer Tjdpfxj Ahhdas Abusd • Capacity: 60 ton per hour • Dimension: 1400 x 6650x1800 mm • Screw Size: Ø 600x6000 mm • Speed: 22 rev/min • Motor: 2 x 5.5 kW Heavy duty Gamak • Water Consumption: 55-205 m3 • Including chassis, motor and safety guards. FOR FURTHER INFORMATION PLEASE FEEL FREE TO CALL US!!!

Condition: ready for operation (used), Kohlhoff Boot & Sole Washer Fully stainless steel Motion sensor activation Boot & Sole brush washer Dimensions: 1500 mm x 320 mm x 1260 mm. Tjdpfx Abe Agcrkeued In excellent condition

Condition: used, Year of construction: 2002, machine/vehicle number: LA14, Used bottle washer dryer GAI - 3500 BPHTechnical Specifications & Performance DataThe Bottle Washer Dryer 5008 is a rotary carousel drying unit engineered for reliable bottle handling within a used bottling line or standalone drying station. Manufactured by Cimec, this second hand machine delivers consistent performance for beverage production and industrial packaging applications where efficient moisture removal is required before downstream labeling, capsule application, or case packing.Model: 5008Year of manufacture: 2002Production speed: up to 3,500 bottles per hourBottle formats (volumetric): Compatible with 0.5L and 0.75L bottle formatsBottle geometry: Cylindrical containersBottle diameter range: 60 mm to 115 mmDrying technology: Rotary carousel (hot air) with anti-condensation featuresPLC installed: NoDocumentation: Paper manuals and electrical schematics availableAdvanced Automation & Control SystemsThe 5008 emphasizes robust mechanical design with straightforward operator control, ideal for facilities prioritizing simplicity and ease of maintenance. While no PLC is installed, the machine’s hot-air drying system integrates anti-condensation management to improve drying effectiveness and reduce residual moisture on the bottle surface. Safety guarding and interlocks are typically part of this class of equipment, supporting safe operation within production environments. Quick mechanical adjustments facilitate format changes across the stated diameter range, helping minimize downtime between production runs.Production Line Integration CapabilitiesThis rotary bottle dryer can operate as a dedicated station or be integrated inline with rinsing, filling, capsuling, and labeling equipment. It is well suited for beverage production lines processing both PET and glass bottles in cylindrical formats. Its compact, carousel-based layout supports smooth infeed and discharge with standard conveyor systems. Format changes within 60–115 mm diameter allow flexibility across common bottle sizes, making it a practical fit for lines handling 0.5L and 0.75L formats.Machine Condition & Maintenance HistoryThe machine has undergone a partial refurbishment in 2025 and has been stopped for approximately one month. It is currently packed and covered, available for inspection. The presence of paper manuals and electrical documentation supports easier recommissioning and setup. Overall, the unit presents as a well-kept second hand component suitable for integration into a used bottling line or as a targeted retrofit in an existing beverage production facility.Operational Performance & VersatilityThe hot-air drying concept with anti-condensation control improves surface dryness prior to downstream operations such as label application or capsule fitting, thereby enhancing label adhesion and presentation. The rotary carousel design ensures consistent residence time and uniform air exposure around the container. Suitable for a broad range of cylindrical bottles, the 5008 supports both PET and glass handling and can complement production of win... Tsdpez E Dlvefx Abujd

Year of construction: 2020, operating hours: 2 h, condition: good (used), functionality: unexamined, For sale is a complete PET bottle recycling washing plant for processing used PET bottles into clean PET flakes. The plant is designed for a production capacity of approximately 1,000 kg/h and is suitable for recycling companies, plastics processors, and companies that want to industrially sort, shred, wash, and dry PET bottles. According to the documentation, the water-contacting components are made of SUS304 / stainless steel 304. Technical Specifications Feature Specification Plant type PET bottle recycling and washing plant Capacity approx. 1,000 kg/h Raw material used PET bottles End product cleaned PET flakes Residual moisture ≤ 1% Flake size approx. 14 mm, adjustable Proportion 8–12 mm ≥ 90% Fine granulate ≤ 3% Powder content ≤ 5% Installed power 238 kW Power consumption approx. 153 kW/h Water requirement approx. 6–8 t/h, recyclable Working area approx. 59 × 4 × 6 m / approx. 208 m² Personnel requirement approx. 9 people Plant scope The line consists of the central machines for the complete recycling process: Conveyor belts Bale opener / De-Baler Label remover Manual sorting station Metal detector Plastic mill / Crusher Screw conveyor Float-sink washing systems High-speed dewatering machines Hot steam washer High-speed friction washer Zig-Zag label blower for label and dust separation Storage or product silo Electrical control cabinet Description This PET washing plant is designed for the industrial recycling process of post-consumer PET bottles. The process begins with the feeding of the compressed bottle bales, followed by bale opening, label removal, manual sorting, and metal detection. Subsequently, the bottles are shredded and cleaned in several washing, friction, and dewatering stages. The plant features a hot steam washer that operates with water at approximately 90–95 °C and, together with cleaning agents, removes oil, dirt, adhesives, and label residues. The flake stream is further cleaned via float-sink washers to separate caps, label residues, and other foreign substances. The final drying takes place via high-speed dewatering units. Todpjzhifisfx Abuod The result is clean PET flakes with a residual moisture content of a maximum of 1%, suitable for further processing, e.g., granulation, extrusion, or recycling into plastic products.

Year of construction: 2017, condition: used, This listing is for the Agilent Biotek 405 TS Microplate Washer The unit is in full working condition and is ready for immediate release BioTek 405 TS Microplate Washer 405TSRS Plate Carrier Source Bottle Todjxv D Hwspfx Abusd Waste Bottle Communication and power cables, and hoses Configuration Details: Manifold Type: 96-tube (8x12) Microplate Types: 96; Standard Plate Profile Volume Range: 50 – 3,000 uL/well Shaking: Yes Soaking: Yes Sonication: Yes Number of Dispensing Liquids: 1 Wash Speed: 96-well, 3 cycles, 300 uL/well:

Condition: used, Year of construction: 2017, Overview Todpsz Dtymefx Abued Complete dressing line for sparkling wine in 750 ml glass bottles, rated at 5,000 bottles/h. The line runs from bottle washing and drying through capsuling and labelling to tray forming, wrap-around packing and vertical packing, linked by approximately 50 m of bottle conveyors, tray conveyors and two accumulation tables. The labelling machine dates from 2017, the packaging end from 2002 and the bottle washer-dryer from 2005. The line is still in production and can be visited on request. Technical data - Year of manufacture: 2017 (labelling machine); remaining machines 2002 to 2005 - Output: 5,000 bottles/h - Product: sparkling wine - Bottles: glass, 750 ml - Bottle conveyors: approx. 50 m total length - Accumulation tables: 2 - Electrical cabinet with power supply and automation included Scope of Delivery - Bottle washer and dryer | CAMES | WDT-12 | 2005 - Capsuling machine | Robino & Galandrino | ZENITH Z 2/16 OTTICO | 2004 - Labelling machine | Sacmi | KUBE K60 | 2017 - Tray former | CERMEX | F28.40 | 2002 - Tray former | CERMEX | F28.40 | 2002 - Bottle deviator | CERMEX | 2002 - Vertical packer | CERMEX | AN90 | 2002 - Wrap-around packer | CERMEX | WB45.00 | 2002 - Laser coder | LINX | SL301 - Hot-melt unit | Nordson - Bottle conveyors | Bobard, Thierion, Anduze | approx. 50 m total length | 2017 - Tray conveyors - 2 accumulation tables - Electrical cabinet with power supply and automation Condition In production. Inspection on site by appointment. Availability Available from 29 January 2027. Location: France.