Used Chamfer for sale (364)

Condition: new, Year of construction: 2022, bar-feeder complete servo control. bar lenght 1500mm max bar diameter 104 mm max store 600 mm include support between barfeeder and machine this when spindle is to short. barfeeder is complete servo control. for turning spindel height between 860 and 1200 mm no chamfering neded. for round and hex material power 380 ~ 415 volt 10 A Hsdpfslczwfjx Acrol 50 Hz total install, 1 Kw no losing time for adjustments like: setup change, like pusher/pushrod. bar stock center adjustment etc. max bar change time 15 sec. need no air pressure ot hydraulic pressure Eco friendly double axis servo control. automatic diameter adjustment. Fas, reliable and flexible. wide bar range and lenght touch screen HMI enter bar diameter and profile by HMI weight 800 kg

Condition: used, Technical details: floor-plate length: 510 mm plate width: 270 mm Hodpfsu N D Dwsx Acrel Plate thickness: 65 mm very good steel plate for sale free, packed in oiled paper and foil Surface ground Ra 0.8 according to drawing T-slots according to DIN 650: a=36; h=65; b=60 c=26mm, chamfered approx. 1.5mm Distance from edge: 100mm; center distance: 100mm (without attached 4x swivel hoist ring) *

Condition: good (used), Year of construction: 2017, NUMERICALLY CONTROLLED EDGE BANDER WITH PRE-MILLING (SPINDLES) & CORNER ROUNDING UNIT Brand: SCM Model: K 360 HP-T-ER1 Serial No.: AH/120944 Ref: 123304 Year: 2017 WORKING CAPACITIES: - Panel height to be machined: 8 - 58 mm Thickness 10 to 45 mm when using rounding unit - Panel length for edgebanding: 210 to 2500 mm - Minimum panel width to be machined: 90 to 1100 mm - Edge thickness in coil: 0.4 to 3 mm without rounding max 3 mm with rounding unit - Edge thickness in strips: max 6 mm without rounding max 3 mm with rounding unit - Edge width: panel thickness + 2 mm each side - Feed rate: 11 m/min - Minimum gap between panels: 600 mm - Panel overhang beyond the transfer chain: 30 mm MACHINE CONFIGURATION: - StarTouch control - Prepared for barcode reader - Reel holder table Ø800 mm - Front extension table - Easy size: digital positioning of infeed fence and panel passage height - Anti-adhesive spray unit - Pre-milling unit (RT-V trimmer) 12,000 RPM - Infrared panel preheating at infeed - Glue application unit (VC-VM) with interchangeable glue pot for granules, capacity: 1 kg. Heating time: 12 minutes Pneumatic pre-cut guillotine Digitally positioned pressure station with 3 rollers (1 roller powered and with timer) - Trimming unit (end cutting) tiltable 0-20° 12,000 RPM - Top/bottom flush trimming unit with digital positioning and copying system. 2 mm radius (or chamfer) router 12,000 RPM - Corner rounding unit R2 mm, 12,000 RPM, digital positioning - Top/bottom R1 & R2 mm radius scrapers with digital positioning - Top/bottom straight scrapers - Edge finishing spray device (Nebulizer) OTHER FEATURES: - Pre-milling group motors: 2x2 kW - End trimming motors: 2x 0.19 kW - Lift/lower motor: 0.30 kW - Feed motor: 1.1 kW - Flush trimming group motors (milling): 2x 0.65 kW - CE Marked - Lockable isolator, emergency stop buttons - Power supply: 380 V, three-phase, 50 Hz - Pneumatic supply: 8-10 bar max, dry air - Extraction: 1x Ø100 mm and 5x Ø80 mm Spindles: 780 m³/h Edge trimming: 360 m³/h Scrapers: 2x360 m³/h Max. footprint in working order: 10.80 x 2.40 m Dimensions for transport (LxWxH): 4.85 x 1.20 x 1.70 m Weight: 1568 kg Hjdorx S Ipopfx Acrel Machine supplied with mounted tools, manual, spare parts list and diagrams.

Condition: new, pressure 80.0 t chamfer lenght 2600 mm distance between columns 2200 mm column arm 250 mm ram stroke speed 90.0 mm/sec work speed 7.5 mm/min return speed 60.0 mm/sec work stroke 160 mm dayligth 380 mm table height 900 mm oil volume 150 ltr. voltage 400 Volt weight 5227 kg range L-W-H 3750 x 1950 x 2400 mm Furnishing: Hsdpjxaafwofx Acrel - DELEM - CNC control model DA-58T - controlled axes: Y1 - Y2 and X - AKAS laser in front of the machine - manual crowning - Upper tool, deer foot - Lower tool, die block with 4Vs - SICK light barrier behind the machine - 2 front support arms - SIEMENS - electrical system - BOSCH / HOERBIGER hydraulic system - CE mark / declaration of conformity - Operating manual: machine and control - Safety manual: press brakes

Condition: new, pressure 200 t chamfer lenght 3100 mm distance between columns 2600 mm column arm 250 mm ram stroke speed 100 mm/sec return speed 75,0 mm/sec work speed 7,0 mm/min work stroke 180 mm dayligth 415 mm oil volume 200 ltr. table height 900 mm voltage 400 Volt range L-W-H 4450x2050x2650 mm Furnishing: - DELEM - CNC control model DA-58T - controlled axes: Y1 - Y2 and X - FIESSLER AKAS - laser protection in front of the machine - Deer foot upper tool - Universal die block - manual table crowning - Safety device: light barrier behind the machine - 2 front support arms - SIEMENS - electrical system Hjdpfxsxaalwe Acrel - BOSCH / HOERBIGER hydraulic system - CE mark / declaration of conformity - Operating manual: machine and control - Safety manual: press brakes

Condition: new, pressure 175 t chamfer lenght 3100 mm distance between columns 2600 mm column arm 410 mm ram stroke speed 180 mm/sec work speed 12.0 mm/min return speed 190 mm/sec work stroke 275 mm dayligth 550 mm oil volume 300 ltr. table height 900 mm table width 90.0 mm voltage 400 Volt total power requirement 15.0 kW weight 9800 kg range L-W-H 4150 x 2150 x 2800 mm ----- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke Hsdpsxabfxjfx Acrjl enlarged projection ----- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot tool Roleri 135.85.R08, "System A" - with additional crowning of the upper wedge - Split universal die block M 460 R, including die shoe C 1050-R - LEUZE light barrier behind d. machine - BOSCH / HOERBIGER hydr. Components - SIEMENS - electrical system - FIESSLER AKAS laser protection device in front of the machine (including FPSC) - 2 front support arms with SLIDING system (plain bearings) - Double foot operation - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes

Condition: used, Year of construction: 2008, pressure 56.0 t chamfer lenght 1400 mm distance between columns 1300 mm throat 220 mm stroke 200 mm dayligth 485 mm work speed 8.0 - 10.0 m/min return speed 35.0 mm/sec Control CNC Boschert back stop - adjustable 0 - 370 mm work height max. 915 mm Cylinders : 2 Stück voltage 3x 400 V connected load 8.0 kVA weight 3700 kg range L-W-H 2320 x 1280 x 2030 mm very good / well-maintained condition (!!) with lots of bending tools - in checked conditions - machine video - ?v=NrpZs6Ar0Vo Equipment: - NC electro-hydraulic press brake - BOSCHERT NC control unit, front - NC electro-motorized back stop (X axis) * with 2x manually adjustable stop fingers (R+Z axis) Hedpoxaanxjfx Acrjl - AMADA PROMECAM (SYSTEM A) upper tool holder - AMADA PROMECAM (SYSTEM A) lower tool holder - Handwheel with analog display for adjusting the bending angle - lots of insert tools, including tool cabinet - 1x working cylinder = double-acting cylinder - upper beam made from a solid steel plate - pressure gauge for pressing pressure (infinitely adjustable) - 2x front support tables - 1x freely movable foot switch - robust machine base - rear protective device (cover + circuit breaker) - original operating instructions (machine + control)

Condition: new, pressure 220 t chamfer lenght 4100 mm distance between columns 3600 mm column arm 410 mm ram stroke speed 180 mm/sec work speed 10.0 mm/sec return speed 160 mm/sec work stroke 275 mm dayligth 550 mm table height 900 mm table width 160 mm oil volume 300 ltr. voltage 400 Volt total power requirement 18.5 kW weight 13800 kg range L-W-H 5150 x 2250 x 3000 mm ----- Press brake with special equipment * increased installation height Hsdpfsxaathex Acrsl * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA-58T graphics / touchscreen * 2D graphic programming * 15 "high definition color TFT screen * Bending sequence calculation * Product programming and display in real size * USB interface - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135.85-R08, system "A" with quick-change clamp - Additional crowning device in the tool holder of the upper tool - Universal die block - BOSCH / HOERBIGER hydr. Components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protective device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "sliding system", with T-slot and tilting cam - 1x double foot control - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes

Condition: new, pressure 320 t chamfer lenght 4100 mm distance between columns 3600 mm Hodpfoxaba Njx Acrol column arm 410 mm ram stroke speed 140 mm/sec work speed 10.5 mm/sec return speed 150 mm/sec work stroke 375 mm dayligth 650 mm table height 900 mm table width 220 mm oil volume 400 ltr. voltage 400 Volt total power requirement 30.0 kW weight 22064 kg Dimensions (HxWxD) 5350 x 2450 x 3150 mm ----- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection ----- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot tool Roleri 135.85.R08, "System A" - with additional crowning of the upper wedge - Universal die block - LEUZE light barrier behind d. machine - BOSCH / HOERBIGER hydr. Components - SIEMENS - electrical system - FIESSLER AKAS laser protection device in front of the machine (including FPSC) - 2 front support arms with SLIDING system (plain bearings) - Double foot operation - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes Special equipment including: - electrical central lubrication

Condition: used, Year of construction: 1996, pressure 130 t chamfer lenght 3060 mm distance between columns 2690 mm column arm 410 mm stroke 215 mm dayligth 385 mm ajustment speed 200 mm/sec working feed 1-10 mm/sec return speed 135 mm/sec table width 120 mm table height 1050 mm tiltable up to +/- 10 mm Number of working hours 53.820 h compressed air 5.0 - 7.0 bar oil volume 250 l operating pressure 340 bar voltage 400 V total power requirement 16.0 KVA weight of the machine ca. 11250 kg range L-W-H 3640 x 2210 x 2375 mm - in checked condition - machine video - ?v=23IbxRaZ2KA Equipment: - CNC electro-hydraulic press brake - including DELEM CNC control model DA 65 * swiveling control panel, front left * 2D graphic programming & product display * tool & program library * including new TFT-LCD industrial monitor - CNC controlled axes: Y1 + Y2 / X / R - CNC electro-motor / controlled back stop (X axis) - CNC electro-motor / controlled height adjustment (R axis) Hjdpfx Acsxabqberjl - manual adjustment of the 2x stop fingers, from the front (Z axes) - manual adjustment of the die displacement, from the front (I axis) - WILA manual table crowning, including analog value display - TRUMPF hydraulic upper tool clamp - TRUMPF manual lower tool clamp - 1x freely movable 2 hand / foot control - Safety device at the rear (sliding door) - Safety device at the side (swinging door) - Original operating instructions + CE declaration + circuit diagram

Condition: new, pressure 220 t chamfer lenght 3760 mm distance between columns 3250 mm column arm 410 mm ram stroke speed 180 mm/sec work speed 10.0 mm/sec return speed 160 mm/sec work stroke 275 mm dayligth 550 mm table height 900 mm table width 160 mm oil volume 300 ltr. voltage 400 Volt total power requirement 18.5 kW weight 12906 kg range L-W-H 5100 x 2250 x 2900 mm ----- Press brake with special equipment * increased installation height * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA 58T (TouchScreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC Hjdpfxew U U Rro Acrsl - Upper deer foot tool with PS 135.85-R08, system "A" with quick-change clamp - Additional crowning device in the tool holder of the upper tool - Universal die block - BOSCH / HOERBIGER hydr. Components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protective device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "sliding system", with T-slot and tilting cam - 1x double foot control - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes

Condition: new, pressure 100 t chamfer lenght 2600 mm distance between columns 2200 mm column arm 410 mm ram stroke speed 200 mm/sec work speed 9.5 mm/sec return speed 155 mm/sec work stroke 275 mm dayligth 530 mm table height 900 mm table width 90.0 mm oil volume 150 ltr. voltage 400 Volt total power requirement 7.5 kW weight 6850 kg range L-W-H 3750 x 1950 x 2800 mm ----- Press brake with special equipment * increased installation height * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA 53T (touchscreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135.85-R08, system "A" with quick-change clamp - Additional crowning device in the tool holder of the upper tool - 4V universal die block M 460 R with die shoe 60 mm holder - BOSCH / HOERBIGER hydr. Components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protective device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "sliding system", with T-slot and tilting cam - 1x double foot control - CE mark / declaration of conformity - User manual: machine and control in German Hedpfx Acexaaqyersl - Safety manual: press brakes

Condition: new, pressure 320 t chamfer lenght 3100 mm distance between columns 2600 mm column arm 410 mm ram stroke speed 140 mm/sec work speed 10.5 mm/sec return speed 150 mm/sec work stroke 375 mm dayligth 650 mm table height 900 mm table width 240 mm oil volume 400 ltr. voltage 400 Volt total power requirement 30.0 kW weight 17082 kg Dimensions (HxWxD) 4550 x 2450 x 3200 mm ----- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection ----- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit Hjdexabdzopfx Acrsl - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot tool Roleri 135.85.R08, "System A" - with additional crowning of the upper wedge - Universal die block - LEUZE light barrier behind d. machine - BOSCH / HOERBIGER hydr. Components - SIEMENS - electrical system - FIESSLER AKAS laser protection device in front of the machine (including FPSC) - 2 front support arms with SLIDING system (plain bearings) - Double foot operation - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes Special equipment including: - electrical central lubrication

Condition: ready for operation (used), Year of construction: 2000, pressure 85.0 t chamfer lenght 2050 mm distance between columns 1650 mm column arm 400 mm stroke 240 mm dayligth 320 - 560 mm Hedpfoxab Ugex Acrsl ajustment speed 150 mm/sec working feed 15.0 mm/sec return speed 150 mm/sec back stop - adjustable 5.0 - 1000 mm table width 110 mm work height max. 1050 mm operating pressure max. 297 bar compressed air 4.5 - 6.0 bar oil volume 200 l operating pressure 340 bar total power requirement 7.5 kW weight of the machine ca. 5900 kg range L-W-H 4100 x 2100 x 2750 mm with increased installation height / piston stroke well-maintained condition (!!) - in checked condition - machine video - ?v=ikl6RNZWeiU Equipment: - CNC electro-hydraulic press brake - including CYBELEC CNC control * swiveling control panel at the front right * external screen - CNC axis adjustment: Y1 - Y2 - X - R - Z1 - Z2 - I + CNC crowning - CNC electro-motorized back stop (X axis) * Travel range .. 5.0 - 1,000 mm * Travel speed .. 250 mm/sec. - CNC electro-motorized height adjustment of the back stop (R axis) * Travel range .. 70 - 235 mm * Travel speed .. 100 mm/sec. - CNC electro-motoric adjustment of the stop fingers (Z axes) * Travel range Z1 .. 405 - 1.565 mm * Travel speed .. 1.000 mm/sec. * Travel range Z2 .. 485 - 1.645 mm * Travel speed .. 1.000 mm/sec. - CNC electro-motoric table crowning - CNC pneumatic die displacement (I axis) - EHT pneumatic tool clamping - upper tool - EHT manual tool clamping - lower tool * Tool holder 90.0 mm + 13.0 mm possible - 1x freely movable 2-hand/foot control - 2x front, stable support arms including "sliding system" - side protective device (swinging doors) - rear protective device (swinging door) - original operating instructions + circuit diagram etc. * Special accessories included: - Oil cooler for use in continuous operation

Condition: used, Year of construction: 1997, pressure 130 t chamfer lenght 3060 mm distance between columns 2690 mm column arm 410 mm stroke 365 mm dayligth 535 mm ajustment speed 200 mm/sec working feed 1.0 - 10.0 mm/sec return speed 135 mm/sec table width 120 mm table height 1050 mm tiltable up to +/- 10.0 mm Number of working hours ca. 31.800 h compressed air 5.0 - 7.0 bar oil volume 250 l operating pressure 340 bar voltage 400 V total power requirement 23.0 KVA weight of the machine ca. 12950 kg range L-W-H 3660 x 2310 x 2900 mm Machine in a well-maintained condition (!!) with only approx. 31.800 operating hours - in checked condition - machine video - ?v=PBV-MDtZnlE Equipment: - CNC electro-hydraulic press brake - DELEM CNC control model DA 65 * swiveling control panel, front left * 2D graphic programming & product display * Tool & program library * USB keyboard and mouse interface - CNC controlled axes: Y1 + Y2 / X1 + X2 / R1 + R2 / Z1 + Z2 / I axis - CNC controlled back stop (X1 + X2 axis) - CNC controlled height adjustment of the back stop (R1 + R2 axis) - CNC controlled adjustment of the stop fingers (Z1 + Z2 axis) - CNC controlled, pneumatic die displacement (I axis) - CNC WILA electro-motoric table crowning - TRUMPF hydraulic upper tool clamping - TRUMPF manuel Lower tool clamp - 1x freely movable 2-hand / foot control - Safety device at the rear (sliding door) - Safety device at the side (swinging door) Hsdpfx Acjxacfmsrsl - Original operating instructions + spare parts list

Condition: new, pressure 40.0 t chamfer lenght 1270 mm distance between columns 1050 mm column arm 350 mm dayligth 387 mm work stroke 170 mm table height 850 mm back stop - adjustable 800 mm adjustment speed 230 mm/min ajustment speed 140 mm/sec working feed 10.0 mm/sec return speed 170 mm/sec total power requirement 5.5 kW weight of the machine ca. 3220 kg dimensions of the machine ca. 2150 x 1650 x 2300 mm ----- Press brake with special equipment * increased installation height * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA 58T (TouchScreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135.85-R08, system "A" with quick-change clamp - Additional crowning device in the tool holder of the upper tool - 4V universal die block M 460 R with die shoe 60 mm holder Hodsw U U Rlepfx Acrjl - BOSCH / HOERBIGER hydr. Components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protective device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "sliding system", with T-slot and tilting cam - 1x double foot control - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes

Condition: new, pressure 400 t chamfer lenght 4100 mm distance between columns 3550 mm column arm 510 mm ram stroke speed 110 mm/sec work speed 8.4 mm/sec return speed 130 mm/sec work stroke 375 mm dayligth 650 mm table height 1000 mm table width 240 mm back stop - adjustable max. 800 mm oil volume 400 ltr. voltage 400 Volt Hodpfexaadtjx Acrol total power requirement 30.0 kW weight 26409 kg range L-W-H 5450 x 2650 x 3470 mm ----- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection ----- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot tool Roleri 135.85.R08, "System A" - with additional crowning of the upper wedge - Universal die block - LEUZE light barrier behind d. machine - BOSCH / HOERBIGER hydr. Components - SIEMENS - electrical system - FIESSLER AKAS laser protection device in front of the machine (including FPSC) - 2 front support arms with SLIDING system (plain bearings) - Double foot operation - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes Special equipment including: - electrical central lubrication

Condition: new, pressure 60.0 t chamfer lenght 2100 mm distance between columns 1700 mm column arm 410 mm ram stroke speed 160 mm/sec work speed 10.0 mm/sec return speed 165 mm/sec work stroke 275 mm dayligth 530 mm table height 900 mm table width 90.0 mm oil volume 150 ltr. voltage 400 Volt total power requirement 7.5 kW weight 5640 kg range L-W-H 3250 x 1960 x 2750 mm ----- Press brake with special equipment * increased installation height Hsdexabckspfx Acrsl * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA 53T (touchscreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135.85-R08, system "A" with quick-change clamp - Additional crowning device in the tool holder of the upper tool - 4V universal die block M 460 R with die shoe 60 mm holder - BOSCH / HOERBIGER hydr. Components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protective device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "sliding system", with T-slot and tilting cam - 1x double foot control - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes

Condition: used, Year of construction: 1995, pressure 80.0 t chamfer lenght 2050 mm distance between columns 1550 mm column arm 250 mm table width 85.0 / 135 mm stroke ca. 390 mm dayligth ca. 585 mm ajustment speed 180 mm/sec working feed 1.0 - 10.0 mm/sec return speed 135 mm/sec work height max. 1050 mm Number of working hours 32.495 h oil volume 200 l operating pressure 320 bar total power requirement 11.6 KW weight of the machine ca. 7300 kg range L-W-H 3700 x 2000 x 3000 mm Good/well-maintained condition (!!) - in checked conditions - machinevideo - ?v=IKyUmzB0WTI ----- CNC electro-hydraulic press brake with: * Increased installation height .. approx. 550 mm * Increased cylinder stroke .. approx. 390 mm ----- Features: - Robust electro-hydraulic press brake * MADE IN GERMANY (!!) - CYBELEC CNC control "DNC 904 PS-A" (SN 0332) * Pivoting, front right Hodpfx Ajxachuocrel * High-resolution graphic display * Clear, easy-to-read menus in the operator's language * Large tool and product library * Graphic 2D programming * Automatic bending sequence calculation - CNC-controlled axis adjustment: Y1+Y2 / X / R axes - CNC electro-motorized backgauge (X axis) * With 4 manually adjustable stop fingers - CNC Electric height adjustment (R axis) - WEINBRENNER electro-hydraulic upper tool clamp - WEINBRENNER electro-hydraulic lower tool clamp - 1x freely movable 2-hand/foot control - 2x front, movable support arms - Side safety device (swinging doors) - Rear safety device (swinging doors) - Machine/control manual + circuit diagram

Condition: used, Year of construction: 1997, pressure 225 t chamfer lenght 3050 mm distance between columns 2550 mm column arm 300 mm ajustment speed 110 mm/sec work speed 9.0 mm/sec return speed 130 mm/sec work stroke 240 mm dayligth 320 - 560 mm table height 1000 mm table width 200 mm oil volume 350 ltr. operating pressure max. 296 bar air pressure 4.5 - 6.0 bar voltage 400 Volt total power requirement 18.5 kW weight 14900 kg range L-W-H 5180 x 2400 x 3100 mm - in checked condition - machine video - ?v=ebbbzSYMxKw Furnishing: - electro-hydraulic CNC die bending/press brake - CYBELEC CNC control "ModEva 12S", swiveling at the front right * High-resolution graphic color screen 14 inches * Representation as a line, area or volume drawing of the product * Clear, concise menus in the operator's language * Large tools and products library - CNC-controlled back gauge adjustment (X-axis) * Stop range X axis of bending line .. 5.0 - 1.000 mm Hjdsxaa Dtjpfx Acrjl * Adjustment speed .. max. 250 mm/sec. - CNC-controlled vertical adjustment of the stop fingers (R axis) * Adjustment range of table surface .. 115 - 265 mm * Adjustment speed .. max. 100 mm/sec. * Adjustment via SERVO motors - CNC-controlled adjustment of the stop fingers left-right (Z1+Z2 axis) * Adjustment range Z1 .. 405 - 2565 mm * Adjustment range Z2 .. 485 - 2645 mm * Adjustment speed .. max. 1000 mm/sec. - WILA CNC-controlled electric table crowning - pneumatic EHT upper tool clamping - manual lower tool clamping - 1x freely movable 2 hand/foot control - 2x front, movable support arms - rear protective device (sliding protective grille) - side protection device (pivoting protective grille) - 1x set of EHT deer foot upper tool - split (3.000 mm) - 1x set of EHT lower tools - split (3.000 mm) - original operating instructions (machine + control)

Condition: new, pressure 175 t chamfer lenght 4100 mm distance between columns 3600 mm column arm 410 mm ram stroke speed 180 mm/sec return speed 135 mm/sec work speed 10,0 mm/sec Hodpfsxabapsx Acrol work stroke 275 mm dayligth 550 mm table height 900 mm table width 90,0 mm oil volume 200 ltr. voltage 400 Volt total power requirement 15,0 kW weight 11.950 kg range L-W-H 5100 x 2150 x 2850 mm ----- Press brake with special equipment * increased installation height * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA-58T graphics / touchscreen * 2D graphic programming * 15 "high definition color TFT screen * Bending sequence calculation * Product programming and display in real size * USB interface - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135.85-R08, system "A" with quick-change clamp - Additional crowning device in the tool holder of the upper tool - 4V universal die block M 460 R with die shoe 60 mm holder - BOSCH / HOERBIGER hydr. Components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protective device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "sliding system", with T-slot and tilting cam - 1x double foot control - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes

Condition: new, pressure 160 t chamfer lenght 3100 mm distance between columns 2600 mm column arm 250 mm ram stroke speed 90.0 mm/sec work speed 7.5 mm/sec return speed 80.0 mm/sec work stroke 160 mm dayligth 395 mm table height 900 mm back stop - adjustable max. 800 mm oil volume 200 ltr. voltage 400 Volt total power requirement 11.0 kW weight 7524 kg range L-W-H 4250 x 1900 x 2550 mm Furnishing: - DELEM CNC control model DA-66T graphic/touch screen * 2D graphical programming * 17" TFT color screen with high resolution * Bending sequence calculation Hedpfxjxab Hij Acrjl * Product programming and real size display * USB interface * intuitive, graphical entry of profiles * Automatic calculation of features: tool safety zones, Press force, bending tolerance, crown setting, stretched Length, embossing force, flattening, automatic rounding calculation * Radius programming * Graphic tool and product library * Collision monitoring * 3D visualization * 1GB memory - controlled axes : Y1 - Y2 and X - manual table crowning - AKAS - laser protection device f. d. machine - Upper tool, deer foot - Lower tool, die block with 4V's - Light barrier behind the machine - 2 front support arms - SIEMENS - electrical system - BOSCH/HOERBIGER hydraulic system - CE mark/Declaration of Conformity - Operating manual : machine and control - Safety manual : press brakes

Condition: new, power capacity 0,75 kW degree 45° Grad turning speeds 10.000 U/min milling height 4,0 mm motor 400 Volt range L-W-H 560 x 300 x 450 mm weight 44,0 kg Description : - Advantage of the sliding guide rail: the workpiece is not moved and therefore cannot be scratched - Ideally suited for deburring and chamfering (visible edges) of various - Materials e.g .: steel, aluminum, non-ferrous materials, plastics, etc. - Ideal for producing visible edges with excellent surface quality - High dead weight for vibration-free work scope of delivery - Slidable guide rail 500 mm - milling head - HM indexable inserts - Operating tool Hodpfx Acoxab H Njrjl

Condition: used, Year of construction: 2004, pressure 50.0 t chamfer lenght 1275 mm distance between columns 1040 mm column arm 250 mm ram stroke speed 225 mm/sec work speed 0 - 9.8 mm/sec return speed 160 mm/sec work stroke 215 mm dayligth 512 mm table height 800 mm back stop - adjustable 600 mm control DELEM DM 51 operating pressure max. 300 bar oil volume 150 ltr. voltage 400 V engine output 6.0 kW Weight 4300 kg range L-W-H 1930 x 1510 x 2390 mm current new price approx. 80.000 euros special price on request good / well-maintained condition (!!) - in checked condition - machine video - ?v=5L8L2AYv0PU ----- PLACKE electro-hydraulic CNC press brake specially developed for the production of small parts The advantages: • Low energy consumption • High operating comfort • Wide range of applications • Fast, robust, low-noise • With CNC control as standard ----- Equipment: - CNC electro-hydraulic press brake with 1x working cylinder - DELEM CNC control model "DM 51" - CNC controlled axis: Y1 - Y2 - X - CNC electro-motorized back stop * Travel path: X = max. 600 mm * Travel speed X axis .. max. 300 mm/s * Positioning accuracy .. +/- 0.02 mm * with 2x manually adjustable stop fingers (R+Z axis) - WILA standard - manual upper tool clamping - WILA standard - manual lower tool clamping - PLACKE safety device at the front: light barrier - side protective device (swivel doors) Hodpoxab U Hsfx Acrjl - rear protective device (swivel + lockable door) - front storage area - side sorting system for bending tools - 1x freely movable foot control - original operating instructions including circuit and hydraulic diagram

Condition: used, Year of construction: 2008, pressure 180 t chamfer lenght 3110 mm distance between columns 2600 mm column arm 410 mm ajustment speed 100 mm/sec working feed 10.0 mm/sec return speed 80.0 mm/sec back stop - adjustable max. 750 mm stroke 260 mm dayligth 460 mm table height 880 mm oil volume 210 ltr. operating pressure max. 240 bar control DELEM total power requirement 15.0 kW weight of the machine ca. 11.200 kg. range L-W-H 4250 x 2000 x 2800 mm Current new price approx. 85.000 euros Special price on request Features: - Electro-hydraulic CNC press brake - With DELEM CNC control model “DA 66W” Hsdpfxoxa Hivo Acrol * 2D graphic programming * Automatic bend sequence calculation and collision detection * High-quality LCD screen (TFT) * Swivel control panel, front left - CNC-controlled axes: Y1 + Y2 + X + R + CNC crowning - CNC electric motor-driven backgauge (X axis) * with 2x manually adjustable stop fingers - CNC electric motor height adjustment of the backgauge (R axis) - CNC electric motor table crowning - ROLLERI upper tool adapter (quick-change clamping) * including crowning device in the tool holder - 2x front, sliding support arms (“sliding” system) - Side guard (swivel doors) - Rear guard (sliding door) - 1x freely movable 2-hand/foot control - Operating instructions (PDF)