Used Edge Magazine for sale (5,900)

Condition: used, Year of construction: 2008, - with workpiece return - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Feed rate max: 20 m/min - with groove milling unit One: Edge banding machine with return Manufacturer: Brandt Type: KDF 991 Year of manufacture: 2008 Workpiece return Manufacturer: Ligmatech Type: ZHR 05 Boomerang Year of manufacture: 2007 Technical data - Right-hand machine - Machine length: 8,260 mm - Ligmatech ZHR 05 length: 10,460 mm - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Thickness of wound edge max: 3 mm Gkedpozuyp Sefx Aayeb - Workpiece width min: 60 mm - Feed rate max: 20 m/min - Stepless feed: material pressure zone adjustable via servomotor - Electromotive height adjustment - Infeed stop: adjustable via servomotor - Infeed stop for thin elements - Glue system for granules: glue pot above the feed chain - BRANDT glue system QUICKMELT QA 45 - Suitable for PUR adhesives - Magazine for single strips - Spray device, front, cleaning at the rear - Pre-milling unit - Preheating zone - End trimmers: 2 motors, pneumatically adjustable - Flush trimming: top + bottom, manually adjustable - Fine milling trimming unit: 2 motors, adjustable via servomotor R2 - Edge rounding unit: 4 motors, manually adjustable - Groove milling unit: manually adjustable with tilting function - Radius trimming blades: R2, pneumatically adjustable / Second set for R1 included - Flat trimming unit - Glue joint trimming blade - Cleaning fluid spray at the rear - Buffing unit - Solid wood edge sanding unit - Conformity marking: Including complete documentation and CE

Year of construction: 1999, condition: reconditioned (used), Machine is currently undergoing overhaul PROCESSABLE MATERIALS Depending on material properties and sheet configuration: · Paper with a minimum grammage of 80 gsm · Cardboard or solid board up to a grammage of 2,000 gsm Gkjdpfx Ajyuuzdeayeb · Corrugated board up to a total thickness of 4 mm (max. sheet curvature 4%) PERFORMANCE DATA Max. sheet format: 820 x 1,130 mm Min. sheet format: 350 x 400 mm Max. cutting force: (400 t) 4.0 MN Max. machine speed: 9,000 sheets/h Standard equipment of the machine: Feeder Non-stop high-performance sheet feeder W3 equipped with: • Automatic non-stop device • Automatic pallet changeover • Suction head • Double-sheet detector • Motorized stack side correction • Motorized suction head adjustment • Conveyor table with pneumatic cover frame • Compressed air and vacuum pump Register Table • Operator-side side lay, switchable between pull and push mode • Light sensor for accurate side alignment of sheets • Fine adjustment of the side lay • Two active front lays with light sensor for register control • Two inactive front lays for sheet stabilization • Separate fine adjustment of gripper edge for drive and operator side • LED display for accurate front and side lay registration • Trend display for sheet detection • Sheet rejection, disabling only the feeder • Height-adjustable top lay for positive sheet guidance Die-cutting station • Roller-guided support rails for the chase • Roller guide for die-cutting plate on swing-out support arms • Motorized die pressure adjustment • Automatic device for lifting the chase to the platen • Electronic die-cutting force display with max. pressure limitation • Vacuum device in sub-table for thin cutting plates Stripping Unit • Frame drive and frame lift for upper tool frame • Mount for the stripping board with centerline fine adjustment • Device for sample sheet removal • Upper tool frame • Lower tool frame Delivery • Fully automatic pile stacker, pre-selectable • Counted sub-stacks with automatic insertion of uncut sheets • Can form sub-stacks (interleaved sheets between 250 gsm – 800 gsm) • Frame lift for upper tool frame • Mount for change frames with electric adjustment in running direction • Pneumatic frame locking • Switchable gripper opener cam and sheet ejector • Sheet jogging device • Integrated conveyor belt for gripper edge or waste grid removal (double-cut) • Separator sheet magazine with electronic level control, refillable from B-side during production • Tool frame with centerline • Change frame for standard pile delivery / gripper edge removal • Change frame for blank separation grid • Mounting kit for separation punch • 8 x sheet hold-downs for standard pile delivery • 4 x cross support bars Options: • QTM – Patented guide rails • QTM – Chase with quick lock system and X/Y adjustment • QTM – Upper stripping frame with quick lock system • QTM – Upper delivery frame with quick lock system • Control upgrade to latest Siemens S7 controller • New generation frequency converters • Modem for remote service connection • Machine height increase: 900 mm

Condition: used, Year of construction: 2015, machine/vehicle number: MR007049, Used: SCM edge banding machine, in very good condition. Complete machine, ready for immediate use. Used: Edge banding machine, manufactured by SCM – model Olimpic K360 T-ER13 Equipped with the following options: - Machine complies with European CE standards - Anti-adhesion spray unit AAR - Glue scraper unit RC-V - Brush unit SP-V - Touch 7 control – 7'' touchscreen control (including the ability to store up to 60 programs) - AUTOSET for T-ER1 3 positions for R-K flush-trimming unit 2 positions for round-over unit pneumatic on/off switching of the glue scraper unit Godpfx Aaozgwzvoyokb - Nesting sensors for the machining units The machine is equipped with the following units: – Pre-milling unit with 2 motors – with compressed air cleaning after milling – Spray unit, sprays after pre-milling, to prevent adhesion of the glue to the surface. – Glue unit, with dual temperature setting for selecting, for example, PU and EVA glue. – Trimming unit for cutting off the edge band. – Milling unit with solid guide rollers, for a perfect milling operation along the surface. – Round-over unit, for milling rounded edges or bevels. – Radius scraper unit for a perfectly smooth finish (R=2). – Spray unit, for dissolving the glue and applying a sheen. – Glue scraper unit, for removing glue residues on the surface. – Brush unit for polishing the glued edge. Technical specifications: - Min./max. band thickness: 0.3-3 mm - Feed speeds: 11 m/min - Minimum panel thickness: 8 mm - Maximum panel thickness: 50 mm - Weight: 1433 kg - Serial number: AH/118707

Condition: used, Machining area: - in the X direction without gluing 6000 mm - in the X direction with gluing 5000 mm - in the Y direction 1200 mm - in the Y direction with main spindle + center distance 20 mm 1300 mm max. workpiece height above - top edge of suction plate Z1 100 mm - max. workpiece thickness Z2, dependent on equipment/application Work table height: approx. 950 mm 1 main spindle with pneumatic feed stroke - drive power: 12 kW in S-1 operation - tool holder: HSK F63, taper diameter = 38 mm - tool change: automatic - change force: 11000 N - tool weight: max. 6 kg - direction of rotation: clockwise/counterclockwise, programmable - speed range: continuously variable 1500 - 24000 rpm, programmable - drive: frequency-controlled three-phase motor - spindle lubrication: single grease lubrication - spindle cooling: water cooling 1 CNC axis rotating 360 degrees 1 vertical drilling unit S21 Machine table consists of: - 6 support arms adjustable in the X direction, each with a rear and center stop, all stops controlled by the program - 6 sets of suction plates consisting of a total of - 6 suction plates 114 x 159 x 100 mm - 6 suction plates 125 x 75 x 100 mm - The support arms and suction plates can be individually positioned according to the corresponding workpiece size. Changeover area: - without pendulum machining, without gluing: X = 2 x 2900 mm - free space in the middle: X = 200 mm - without pendulum machining, with gluing: X = 2 x 2150 mm - free space in the middle: X = 700 mm - with pendulum machining, without gluing: X = 2 x 2400 mm - free space in the middle: X = 1200 mm - with pendulum machining, with gluing: X = 2 x 1700 mm - free space in the middle: X = 1600 mm Gkodpfxjzupibo Aaysb Feed drive system Rapid traverse rates: - X-axis 100 m/min - Z-axis 25 m/min Air pressure: 6 bar Tool changer magazine with 18 positions Tool coding: position-coded Tool weight: max. 6 kg Tool length: max. 150 mm Tool diameter: max. 100 mm when fully loaded max. 150 mm with free adjacent positions or nesting Central connection for extraction Mains voltage: 3/N/PE, 400/230 V, 50 Hz 1 vacuum pump 100 m3/h

Condition: good (used), Year of construction: 2002, machine/vehicle number: P/50078, functionality: fully functional, power: 17 kW (23.11 HP), input voltage: 24 V, input current: 40 A, input frequency: 50 Hz, type of input current: three-phase, edge thickness (max.): 20 mm, height adjustment type: electric, actuation type: electric, total height: 1,500 mm, total length: 8,200 mm, total width: 1,000 mm, overall weight: 3,300 kg, Equipment: CE marking, documentation/manual, Here are some additional key specifications for the machine: Edge thickness: 0.3 – 20 mm Panel thickness: up to 60 mm Feed rate: 12 – 20 m/min Gkodozy Nzzepfx Aayjb Due to a change in the production line, this edge banding machine is now available for sale. The machine was used infrequently in recent years but remained in operation until April 2026. All functions are working, but some fine adjustments are required. The machine is disconnected from the power supply and is located in the heated hall. The manual and adjustment tools are included. A generous amount of edge banding material is included in the purchase price (see photo). A forklift is available for loading. If necessary, a second forklift can be arranged.

Condition: used, Year of construction: 2005, functionality: fully functional, travel distance X-axis: 1,500 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 700 mm, spindle speed (max.): 8,000 rpm, Milling machine Year of construction: 2025 Work table, clamping surface: mm 1500 x 1000 Table height: mm 750 Number of T-slots: 7 Size of T-slots DIN 650: mm 18 Travel distances X-axis: mm 1500 Y-axis: mm 1000 Z-axis: mm 700 Distance: Table top edge - Spindle bottom edge min/max: mm 150 / 850 Main spindle drive for speed 8000 min-1 Tool holder: SK 40 AC motor, frequency-controlled: kW 26 at 44% duty cycle Speed range: min-1 15 – 8000 Torque: Nm 245 Coolant system Band filter system Gksdpfx Aezvbaujaysb Feed drives X-axis AC servo motor: kW 3.5 Y-axis AC servo motor: kW 2.0 Z-axis AC servo motor: kW 3.5 Rapid traverse speeds (X/Y/Z): m/min 30/30/20 Indirect position measurement system. Accuracy Positioning accuracy X and Y axes over 1000 mm: mm ± 0.0150 Repeatability X and Y axes: mm ± 0.0075 Positioning accuracy Z axis: mm ± 0.0150 Repeatability Z axis: mm ± 0.0075 Tool magazine, 24-position mounted on the left side of the machine - Tool positions: 24 - Tool shank (DIN 69871 / 69872): SK 40 - Max. tool diameter: mm 76 - Max. tool length: mm 250 - Max. tool weight: kg 8 Machine control: Heidenhain iTNC530 Ex works, unloaded, plus statutory VAT. No guarantee.

Condition: not inspected (used), Year of construction: 2011, functionality: unexamined, travel distance X-axis: 6,200 mm, travel distance Y-axis: 1,935 mm, workpiece height (max.): 250 mm, number of axes: 4, number of spindles: 40, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Panel thickness (edge banding unit): 14 - 60 mm Maximum panel thickness: 350 mm Number of vertical drilling spindles: 28 Number of horizontal drilling spindles in X-direction: 4 Number of horizontal drilling spindles in Y-direction: 8 Total number of drilling spindles: 40 Total number of tool changer positions: 22 Number of suction beam traverses: 10 Milling Unit Number of axes: 4 Motor power: 10.5 kW Automatic tool changer Edge banding unit Glue unit Tool magazine Grooving unit Number of places in tool magazine: 22 MACHINE DETAILS Main spindle power: 10.5 kW Gsdpfx Aaeyqzrnsyekb Total power: 31 kW EQUIPMENT Vacuum pump Safety grid Chip conveyor The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photographic documentation and technical/commercial documents with descriptive character. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 8011

Condition: ready for operation (used), Year of construction: 2011, machine/vehicle number: 36956, functionality: fully functional, workpiece height (max.): 60 mm, edge thickness (max.): 3 mm, total length: 9,800 mm, overall weight: 600 kg, plate height: 1,060 mm, TECHNICAL DETAILS Workpiece height: 60 mm Edge thickness: up to 3 mm Minimum panel width: 55 mm Minimum panel length: 100 mm Panel height: 1,060 mm Tool interface: ISO 30 MACHINE DETAILS Dimensions & weight Total length: 9,800 mm Weight: 600 kg Input frequency: 50 Hz EQUIPMENT Return system Operates with PUR adhesive Gkjdpfxox A Tzqo Aaysb Spray system Pre-milling unit RT 20 Gluing unit SP 20 6-position edge magazine End trimming unit IT 90-S Rough milling unit RS 10 Fine trimming unit RF 40 Note: Further information regarding equipment can be found on the attached machine data sheet.

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, workpiece height (max.): 60 mm, workpiece width (max.): 60 mm, edge thickness (max.): 20 mm, The machine has been serviced and is in excellent condition. It is immediately ready for operation! TECHNICAL DETAILS - Edge thickness (glued): max. 20 mm - Maximum gluing height: 60 mm Gkedsxzfwbopfx Aayjb - Maximum roll material thickness: 3 mm - Piece width: min. 60 mm - Maximum feed rate: up to 25 m/min - Feed: continuous - Electric height adjustment: available - Pressure system: upper belt pressure - Preheating zone: available - Granulate glue system: with pre-fabricated container - Glue pot: interchangeable/variable - Spray unit: available - Pre-milling unit: available - Trimming unit: with 2 motors - Milling stations: flush/radial/chamfer, 1 available - Corner rounding unit: with 2 motors - Edge scraper: profile and planer - Buffing unit: available - Strip magazine: available - Units: synchronized units with NC axis/axes - Machine version: left hand side - Quick-change units: available MACHINE DETAILS - Remote control: PowerControl PC 22 - Weight: 5,000 kg - Machine length: 7,845 mm - Standards: CE requirements EQUIPMENT - Special equipment: with nesting - New chains - HOMAG feed device with 2 rollers - HOMAG A 20 glue unit - HOMAG HL 84 - HOMAG FK 11 - HOMAG PN 10 profile pull scrape unit - HOMAG FA 11 finishing unit

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, workpiece height (max.): 40 mm, edge thickness (max.): 6 mm, feed rate X-axis: 11 m/min, rotational speed (max.): 12,000 rpm, Equipment: CE marking, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Max. feed speed: 11 m/min Maximum panel thickness: 40 mm Min. panel height: 8 mm Max. panel height: 40 mm Min. edge thickness: 0.3 mm Max. edge thickness: 6 mm Maximum spindle speed: 12,000 rpm MACHINE DETAILS Trimming unit Unit: Format cutting Unit: Trimming Automatic engagement by time Motor power: 2.2 kW Edge heating lamps Coil magazine Number of positions: 1 Gluing system Hot melt glue pot Edge pressure roller conveyor Number of pressure rollers: 3 Edge processing unit 1 Unit: End trimming Number of motors: 2 Gkedpfx Aexw Ttveayob Automatic engagement by time Motor power: 0.18 kW Maximum speed: 12,000 rpm Edge processing unit 2 Unit: Top/bottom trimming Number of motors: 2 Motor power: 0.27 kW Maximum speed: 12,000 rpm Edge processing unit 3 Unit: Multifunction Number of motors: 1 Motor power: 0.35 kW Maximum speed: 12,000 rpm Edge processing unit 4 Unit: Scraper Edge processing unit 5 Unit: Buffing Number of motors: 2 Motor power: 0.1 kW Total installed power: 13 kW EQUIPMENT Control system: PC 16 CE marking

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Godpjzu T Sgefx Aayokb Condition: Functionally tested Equipment: Base machine Extendable boom Joint milling unit 1801 Edge feed system, fully automatic 1903 Glujet 201 adhesive application system, cartridge Printing unit 1912-3, pneumatic Cutting unit 1918 Combination milling unit FR201 Pulling blade unit 1929 Chip collection box Surface pulling blade 1964 Location: Flörsheim Availability: Short-term

Condition: good (used), Year of construction: 2023, functionality: fully functional, operating hours: 59,000 h, input voltage: 400 V, input frequency: 60 Hz, type of input current: three-phase, workpiece height (max.): 50 mm, edge thickness (max.): 5 mm, actuation type: electric, total height: 2,000 mm, total length: 3,095 mm, total width: 1,330 mm, overall weight: 700 kg, Equipment: documentation/manual, 2023 Good condition For inquiries, please contact: Gergely Repka 06707739050 Professional edge banding machine suitable for edge sealing and post-processing of panel-format sheet materials. It can be used for particleboard, MDF, furniture board, table tops, etc. Key technical data: * Coil edge banding: 0.4–3 mm * Strip edge banding: 0.4–5 mm * Maximum edge height: 55 mm * Processable sheet thickness: 8–50 mm * Edge banding cross-section: max. 5 × 50 mm (material-dependent) * Minimum workpiece width: 70 mm * Minimum workpiece length: 180 / 210 mm * Feed speed: 9 m/min * Manually adjustable pressure beam * Extendable workpiece support with 500 mm distance Equipment: * Edge Control BC15 control system with a 15.6" touchscreen * Vi.se. (Visual Setting) digital setting system for quick and accurate machine adjustment * FG101 pre-milling unit with 2 diamond milling heads * MG101 edge feeding unit * Glu Jet GJ101 hybrid adhesive technology (2.3 kW / 50 Hz) with automatic adhesive height adjustment * 1.4 kg adhesive tank (for 4 cartridges) * Glu Jet cleaning tank * Automatic refilling system * DW101 pressing unit * KA101 pneumatic end trimming unit, 1 motor version * 0.22 kW * 12,000 rpm * FR101 profile smoothing unit * chamfering and radius function * 2 × 0.37 kW * 12,000 rpm * 2 replaceable HW milling heads Ø75, Z4, R2 * FF101 corner rounding unit with dual linear guide * ZK101 scraping unit R=2.0 mm * Chip collection system * FK101 surface scraper unit * SW101 polishing unit * 2 × 0.13 kW * 1,400 rpm * 2 textile polishing discs, 120 mm * Adjustable from 0–5° * TR101 spraying unit for infeed and outfeed sides Gedpfx Aszi Am Noayskb

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, workpiece height (max.): 50 mm, workpiece width (max.): 2,500 mm, workpiece length (max.): 200 mm, rotational speed (max.): 18,000 rpm, Equipment: CE marking, TECHNICAL DETAILS Panel width max.: 2,500 mm Panel width min.: 130 mm Panel height max.: 50 mm Panel height min.: 8 mm Panel length max.: 200 mm Panel length min.: 30 mm UNITS Sizing unit Unit: Trimming Unit: Corrections automatic engagement based on timer Motor power: 2.2 kW Max. speed: 6,000 rpm Magazine for coil Number of positions: 1 Gluing system Glue pot for polyurethane adhesive Prefuser for polyurethane adhesive Prefuser for polyurethane adhesive D4-e Edge pressure roller track Gkedpfx Aasxxavtsyob Number of pressure rollers: 4 Edge processing unit 1 Unit: Top router Number of motors: 1 Motor power: 0.7 kW Max. speed: 18,000 rpm Edge processing unit 2 Unit: Top router Number of motors: 1 Motor power: 0.7 kW Max. speed: 18,000 rpm Edge processing unit 3 Unit: Hot air blower Model: APPLICATORE DI FILM Motor power: 0.1 kW Edge processing unit 4 Unit: Brush Number of motors: 2 Edge processing unit 5 Unit: Top router Number of motors: 1 Edge processing unit 6 Unit: Top router Number of motors: 1 MACHINE DETAILS Installed total power: 12 kW Adhesive system: PUR Pressure type: rubber-coated belts Number of units installed in sizing: 1 Number of units installed in edge processing: 6 EQUIPMENT Spraying unit CE marking

Condition: used, Year of construction: 1997, Second-hand machine Year of manufacture: 1997 Condition: well-maintained Features and technical specifications: Machine with PLC control Gkjdpfx Ajzk N Hroaysb Feed rate: 12/16 m/min Edge feeder for roll and strip material, automatic 1901 Glue application unit, cartridge 1906, with sensing nozzle Pneumatic pressure unit, motorised adjustment to edge thickness 1926 Trimming unit, twin-motor, pneumatically swivelling 1918 Rigid milling unit up to 30 mm, 1962 MOT 5 milling unit with multifunction capabilities: flush, radius, chamfer, 1966 Radius scraper 1927 Corner copying machine 1983 Surface scraper 1964 1944 sanding unit Blow moulding nozzles Technical specifications: Workpiece thickness min./max.: 6/60 mm Workpiece width min. 60 mm Minimum workpiece length: 140 mm Maximum gluing thickness: 13 mm Weight: 1,350 kg Machine dimensions: 5850 x 1000 x 1750 mm Location: Röllbach Availability: at short notice

Year of construction: 2005, condition: used, CNC-controlled erosion machine for the processing (erosion, grinding, polishing) of PCD tipped tools up to 400 mm diameter and 400 mm length, according to disc-electrical-erosion processes for use in service and in production. Accessories: Total enclosure Software path management Software P- System for peeling cutters, Software shaft endmills (207/208) Software discoid tools face (221/222/223/224) Software profiled workpieces (233/234/239/240) Software hoggers, profiled hoggers (255/256/257/258/260/261/262/263) Software discoid tools (264/265) Software shaft and jointing cutters (267/268/277/278) Software step tools (271) Software scoring saws (299) Software saws flat tooth (301) Software saws single sided with chamfer (302/303) Software saws alternate tooth (304) Software saws triple chip (309) Software saws flat top tooth (310) Software saws flat trapezoid tooth (311) Software saws alternate tooth with chamfer (312) Software shaft and jointing cutters (7/8) Software shaft and jointing cutters profiled (33/34) Software hoggers, profiled hoggers (53/54/55/56/57/58) Software discoid tools (64/65) Software shaft and jointing cutters (67/68/77/78) Software compensation (90) Software saws flat tooth (101) Software saws single sided with chamfer (102/103) Software saws alternate tooth (104) Software saws triple chip tooth (109) Software saws flat top tooth (110) Software saws triple chip tooth (111) Software saws alternate tooth with chamfer (112) Software for polishing of profiled hoggers (757/758/760/761) Filter system with chiller for dielectric fluid Automatic fire extinguishing system DIN 14497 Standard programs for measuring, eroding etc. Program for chamfering of workpiece cutting edges, Automatic Diagnosis program for machine operational status with text output on screen Loader for workpieces, with CNC-controlled pivot for loading and unloading to a magazine, 6 sided erosion wheel changer, Workhead SK 50 with adapter to 12 HSK 63 A, Turntable workpiece magazine for 12 workpieces SK 50, Turntable workpiece magazine for 4 workpieces SK 50, 6 flush sets QXD250 CAD/CAM for external PC workstation including ARES drawing program, Industrial PC external PC workstation with desktop PC, monitor, keyboard, and mouse, 1 HSK63 F adapter for measuring the machine. X axis travel: 730 mm B axis travel: +/- 30 ° Y-axis travel: 840 mm Gsdpow S I Dgsfx Aayekb Z axis travel: 500 mm E-axis: 330° A-axis: 360° Workpiece carrier: SK50 workpiece length max.: 400 mm Workpiece diameter max.: 400 mm workpiece weight max.: 15 kg Connected load approx.: 6.7 kW (400 V / 50 Hz Dimensions W x D x H approx.: 2160 x 3435 x 2190 mm Weight approx.: 7800 kg colour: RAL 7047 Telegray 4, color RAL 7045 Telegray 1

Condition: ready for operation (used), Year of construction: 2008, machine/vehicle number: 77503, functionality: fully functional, workpiece height (max.): 60 mm, feed rate X-axis: 25 m/min, overall weight: 6,510 kg, controller manufacturer: SINTRA, TECHNICAL DETAILS Panel height: 60 mm Solid wood: 20 mm PVC / ABS: 3 mm Max. feed speed: 25 m/min MACHINE DETAILS Control: Sintra Weight: 6,510 kg Gedeydidrspfx Aayjkb EQUIPMENT - Sanding unit - Coil holder magazine with 2 positions and automatic edge change via CNC - Adhesive unit for EVA hot-melt glue with preheating device and glue pot - Preparation for adhesive unit for PUR glue - Pressure group for straight profiles with electronically adjustable pressure rollers via CNC - End trimming unit with 2 motors and automatic tilt adjustment - Filler unit with 2 vertically aligned motors - Edge smoothing unit with 2 swivelling motors - Multifunctional 4-motor corner rounding unit (smoother + corner rounder) with numerical control in automatic adaptation - Anti-stick unit - Adjustable edge scraper unit - Glue-saving unit - Oscillating brush unit - Electronically adjustable working height - Motorized rubber belt with increased pressure - Motorized and electronically adjustable panel guide - Side roller conveyor with idler rollers for panel support

Condition: new, HOLZ-HER 7405 EVOLUTION CONNECT machining center -Exhibition machine- This offer includes an equipment package. The following items and options are already included in the price: - Material support - Height-adjustable infeed roller conveyor - Diamond edge trimming cutter set EVOLUTION - CAMPUS V8 EVOLUTION CAD/CAM software - Flat screen monitor, 21.5", 16:9 - Laser workpiece length measurement - Milling head 7830 - Tool changer 7887, 6-position magazine, pick-up - Vacuum system ECO - Air conditioning unit for control cabinet cooling - Tool changer 7874 Gsdpfx Aezq Dbdeayskb - Angular gearbox 7869 - Adapter for Clamex cutter - Tool set - 4-axis CLAMEX - Tool holder HSK-F 63 - Drilling unit XL 7885, 19 spindles - Handheld control unit - Tool set - EVOLUTION for XL drilling head 7885 - New exhibition machine -

Condition: used, Norpak Magazine Sorting and Polywrapping Line, Variable Size Infeed Hopper A4 - A5, In Leaf Capability, 4 Document Feeder A4 - A5, Poly Wrap Station with Heated Sealer Bars & Cut Off, Outfeed Conveyor, 8m x 3m Foot Print, Including Extraction System. S/No. 0701047 (Selection of Polywrap & Potato Starch film) Godpfxszwntqo Aayekb Highest bid is subject to vendors approval. Please Note: This lot is located in Birmingham, UK. A charge of £300 for dismantling and loading onto suitable transport will be automatically added to your invoice should you be successful in purchasing this item. Blocking and securing will be at the cost of the purchaser.

Condition: excellent (used), Year of construction: 2013, Brandt Highflex KDF 220 edge banding machine with joining, corner copying, and two trimming blades. Highly automated. A video of the machine in operation can be sent upon request. Edge thickness range approx. 0.4 - 3mm, solid edge up to 6mm Workpiece height approx. 10 - 60mm Feed speed approx. 10m/min Noise protection hood Extendable workpiece support Dust extraction connection 1x120mm, 1x100mm, 3x80mm Easy-Touch control panel EC+ for easy machine operation 4 programs can be stored. Machine in Highflex version, highly automated, switching from thin edge to thick edge via programs Units: Extended infeed zone Chain track central lubrication, pneumatic manual Glue pot quick-change device, currently one glue pot available Godpfx Aszzqwmoayokb Top pressure manual adjustment, PU rollers Infeed guide manual adjustment with SIKO counter for chip removal Joining milling cutter with diamond milling cutters, sharpened Contact heating shoe for preheating the panel Gluing section with automatic edge feed for roll material up to 3mm, switchable for co-rotating and counter-rotating operation Pressure zone with 3 rollers, pneumatic adjustment between thin and thick edge Cut-off saw with 2 motors, straight cuts or bevel cuts (program adjustment) Combination milling unit, pneumatically controlled for flush trimming, chamfer and radius Corner rounding milling cutter R2 with diamond milling cutter with integrated sensing ring Radius trimming blade R2, pneumatically retractable with quick-change device Glue joint trimming blade with large roller, pneumatically controlled Hood locking CE marking All indexable inserts of the milling units and the trimming blades have been renewed or re-sharpened, saws sharpened, diamond joining milling cutters sharpened. The machine is therefore ready for immediate use. Only the diamond milling cutter of the profile milling unit has not been renewed, but it is still sharp. Original paint, only a few spots have been touched up. Unfortunately, the machine does not have an operating hour counter, but it still looks very good visually. Very good condition, see original photos. Machine dimensions approx. 4550 x 1250 x 1550mm (LxWxH) Weight approx. 1400kg. The machine can be demonstrated on-site by appointment. We only offer machines that are ready for demonstration and are in our warehouse, see "other offers from this provider".

Condition: used, Year of construction: 2007, total height: 1,600 mm, total length: 5,200 mm, total width: 1,200 mm, Colour: Grey Weight: 1.550 kg - Year: 2007 - Documentation available: No - CE certificate present: No - Serial number: 1328 - Transport dimensions: 5200mm x 1200mm x 1600mm (l x w x h) - Transport weight [kg]: 1550kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT Gksdsw Rd Tzopfx Aaysb VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: like new (used), Year of construction: 2021, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, workpiece height (max.): 60 mm, edge thickness (max.): 6 mm, total length: 4,412 mm, Equipment: documentation/manual, We are offering this like-new Format4 tempora F600 60.06L edge banding machine, manufactured in 2021. It features sharp pre-milling cutters, AdvantEdge zero-joint technology, X Motion PLUS control system, interchangeable glue tank, a 2-motor corner rounding unit, spraying system, polishing unit, etc. The 'Nesting' package also ensures that banding can be applied along pre-drilled holes and other cutouts. This is a very complete and well-maintained machine in excellent condition. Gsdpezt Dkkofx Aayekb It is being sold due to a change in business activities. The machine can be inspected while in operation. Manufacturer: Format4 Model: tempora F600 60.06L Year of manufacture: 2021 Condition: like new Category ID: 877 Type ID: 664 Machine type: edge banding machine If you have any questions or would like more information, please feel free to send us a message or call us.

Condition: like new (used), Year of construction: 2007, total length: 1,700 mm, total width: 900 mm, total height: 1,200 mm, overall weight: 300 kg, height adjustment type: electric, grinding belt length: 2,650 mm, grinding belt width: 150 mm, Volpato edge sander – MADE IN ITALY! - Working height: 150mm - Sanding belt length: 2650mm - Mechanical sanding belt oscillation - Main motor: 2.2 kW - Control panel - Sanding at angles from 5 to 90 degrees - Year: 2007 Machine dimensions: - Length: 1700 mm - Width: 900 mm - Height: 1200 mm - Weight: 300 kg Machine testing is possible on-site. Financing options are available through leasing or installments. WE ORGANIZE TRANSPORT. WHERE CAN YOU SEE OUR MACHINES? JBS WOODWORKING MACHINERY WOLICA DRUGA 26 23-310 MODLIBORZYCE Gsdpfszxyuvsx Aayokb jbsmaszyny.pl We have the following machines available: band saws, circular saws, crosscut saws and panel saws, planers, jointers, sanders, horizontal and vertical drilling machines, feed systems, sharpeners, four-sided planers, 4-sided, 3-sided, three-sided, two-sided, thicknessers, jointers, sanders, planers, combined planer-jointers, combined planer-thicknessers, combined jointer-thicknessers, thicknesser-jointers, cleaning machines, mortisers, tenoners, parquet machines, trimmers, edge trimmers, machines for log homes, milling machines, routers, spindle mounters, top routers, bottom routers, sanders, wide belt sanders, throughfeed sanders, roller sanders, disc sanders, angle sanders, jointers, drills, drilling machines, horizontal, radial, milling machines, multi-spindle, edge banding machines, edge banders, veneer machines, presses, lathes, sawmills, briquetting machines, chippers, wood chippers, dowel machines, mortising machines, dust extraction systems, extractors, fans, compressors, sharpening machines, multi-functional machines.

Condition: used, Year of construction: 2000, Used machine MAKA CNC Door Processing Center HC 55 TBZ Year of manufacture: 2000 CNC machining center for processing interior doors (hardware mortising, vision panel cut-outs, peephole machining, etc.) CNC control BWO 900C, with 1 MB memory, integrated PC. Working ranges: For door width: 250 – 1,280 mm For door height: max. 2,500 mm For door leaf thickness: max. 80 mm Rapid traverse speed: X / Y-axis: 45 m/min Z-axis: 10 m/min Gkodpfsv S Dn Dex Aayeb 1 universal milling unit SK40 With integrated A-axis swivel 190° (+/- 95°), along X-axis for lock/hinge machining on both sides along the longitudinal door edge directly with the unit. Water-cooled milling spindle, nominal output 8 kW, available from 7,000 rpm, continuously variable speed from 1,000 – 17,100 rpm, SK40 tool holder for automatic tool change. 1 chain-type tool magazine with 24 positions, for tools up to Ø 90 mm, for sorted storage up to max. Ø 160 mm, positioned at unit’s service position. Max. tool length 200 mm from spindle mount. Milling spindle and 2 x magazine positions equipped for angle/feeler heads with torque support. Machine table with width adjustment via program, as well as width measurement for edge processing for consistent milling depth on both sides. 1 set of infeed rollers for manual loading, automatically elevating and lowering. 1 longitudinal stop with pneumatic insertion stroke, mounted on the traversing unit for positioning according to door length and thickness. 4 pneumatic lateral stops, swing-in type, for doors with veneer/cover overhang up to max. 15 mm, with selectable height adjustment for varying stop heights on finished doors (single/double rebate doors). 2 vacuum clamping lines, 5 vacuum suction cups per line, 130/200 x 70 mm, with touch valve and blow-off device. Per line, 3 vacuum cups can be lowered according to the door height being processed. 1 vacuum pump, approx. 128 m³/h suction capacity, with 250-liter intermediate tank, enabling rapid vacuum build-up. Automatic central lubrication, free-standing control cabinet with air conditioner. Safety features: Bumper on both sides of the gantry, protective fencing on the sides. Various tools and tool holders can be taken over by agreement. The machine can be inspected in Hermaringen.

Condition: excellent (used), Year of construction: 2014, I sell the BIESSE line consisting of: Biesse Winner WRT loading infeed device 1-channel Biesse control station for failure elements Biesse Edge 1 shaped elements edge banding and element working station Biesse Edge 2 shaped elements edge banding station Biesse Edge 3 shaped elements working station Biesse Edge 4 shaped elements working station with drilling and inserting Wandres cleaning device Biesse Winner WRT unloading outfeed device 1-channel Manufacture year 2014. Gkjdpsznfd Uefx Aayeb Available immediately. Possible to see at work. Possible to adjust for certain product. For more photos and details please send the request.

Condition: used, Year of construction: 2008, power: 41 kW (55.74 HP), edge thickness (max.): 3 mm, controller model: ICOS OPEN, The machine has the following configuration: Pre-milling unit Manufacturer model: R3 L20 Engagement control: Automatic, time-controlled Motor power: 4 kW Speed: 9,000 rpm Edge processing Number of edge processing units: 10 Crosscut saw unit Manufacturer model: 8.42/39/B Number of motors: 2 Motor power: 0.6 kW Speed: 12,000 rpm Flush trimming and rounding unit Manufacturer model: 08.055 Number of motors: 0.6 (?) Motor power: 1 kW Speed: 12,000 rpm Corner rounding unit Manufacturer model: 08.342 Number of motors: 2 Motor power: 0.66 kW Speed: 12,000 rpm Scraper blade unit Manufacturer model: 08.50 Belt sanding unit 1 Manufacturer model: 08.62 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 2 Manufacturer model: 08.062 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 3 Manufacturer model: 08 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 4 Manufacturer model: 08.617-2 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 5 Manufacturer model: 08 Processing unit 10 Manufacturer model: 08.190 Gkedpfjzmtkaox Aaysb Motor power: 4.5 kW Speed: 9,000 rpm TECHNICAL DETAILS Workpiece dimensions Max. panel height: 60 mm Min. panel length: 130 mm Min. panel width: 65 mm Edge material Min. edge thickness: 0.4 mm Max. edge thickness: 3 mm Feed Max. feed rate: 30 m/min Pressure: Rubber belt Number of panel sizing/milling units: 1 MACHINE DETAILS Control system: ICOS OPEN Total connected power: 41 kW EQUIPMENT Number of panel sizing/milling units: 1 Lamps for preheating the panel side Edge roller magazine with 2 positions PUR pre-melting unit Pressure roller set with 5 pressure rollers Spraying unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at its destination. External reference: 5657