Used Operating Instructions for sale (25,738)

Condition: used, Radial drilling machine CSEPEL type RFh 75 / 1500 Machine no. No. 13704 Year of construction 1985 Hjdpolhwr Rsfx Abdji Drilling capacity in steel Ø 75 mm Drilling capacity in cast iron Ø 90 mm Spindle holder MK 5 Nominal throat depth 1500 mm Largest projection of the spindle 1500 mm (to the column) Smallest projection of the spindle 440 mm (to the column) Distance spindle nose - clamping surface 370 - 1700 mm Cantilever height adjustment 950 mm Table size / clamping surface 1800 x 1100 mm Column diameter 450 mm Pinol stroke 380 mm Spindle speed 19-1900 rpm 21 steps Feed rate 0.047-2mm/rev. 12 steps Motor power 11 kW Mains connection 380 Volt, 50 Hz, 15 kW - Clockwise/anticlockwise rotation of the drilling spindle via hand lever switch - Hydr. gear shift for spindle speed and feed speed - Hydro-mechanical central clamping - Motorized boom height adjustment - Without coolant device - Machine light - Operating instructions Space requirement: Length 2720 mm x width 1170 mm x height max. 3770 mm Transport height with motor on the column: 3500 mm Transport height without motor on the column: 3250 mm Weight: 6.3 tons good condition

Condition: used, mileage: 19 km, power: 110 kW (149.56 HP), first registration: 08/2025, fuel type: diesel, overall weight: 3,500 kg, next inspection (TÜV): 03/2028, color: white, gearing type: mechanical, emission class: euro6, number of seats: 3, loading space length: 3,272 mm, loading space width: 1,787 mm, loading space height: 1,519 mm, Year of construction: 2024, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, Internal vehicle no.: 153225 Location: OsnaTruck Nutzfahrzeugservice GmbH in Osnabrück (postal code 49076), Prof.-Porsche-Str. 7 * Tel.: Exterior * Electrically folding exterior mirrors * Heated and electrically adjustable exterior mirrors * Grab handle at the load compartment sliding door on the partition wall * Wheelbase 3,665 mm * Sliding door on the right side Interior * Armrest for driver’s seat * Outside temperature display * Dual passenger seat * Roof light(s) in the load/passenger compartment with door contact * Full partition wall Safety * Adaptive brake light * Driver's airbag * Passenger airbag Comfort and Environment * Attention Assist * Hill Start Assist * ECO start-stop function * Light assistant * Mercedes-Benz emergency call system * Multifunction steering wheel * Rain sensor * Gear shift indicator Hjdpjw N Uzysfx Abdji * Crosswind Assist * Cruise control * Blind Spot Assist Multimedia * Digital radio (DAB) with Bluetooth hands-free system * Instrument cluster with color display Equipment Lines and Packages * Winter package Condition / Documents * COC papers Additional features * 3.5-ton vehicle * 6-speed manual transmission ECO Gear * Storage compartment under dashboard * Overhead storage above windscreen * Active Brake Assist * Active Lane Keeping Assist * Acoustic package * Trailer load up to 3,500 kg possible * Tachograph operation front, under roof liner * Front cupholders * Digital operator’s manual * Third brake light * Wiring for trailer socket * HVO-compatible vehicle * Alternator 14 V / 250 A * Seat belt warning for passenger * Seat belt warning for driver * Semi-automatic TEMPMATIC air conditioning * Wooden floor * Interior lining of load compartment up to roof height (wood) * Intelligent Speed Assist (ISA) * Coat hook in driver's cab * Communications module (LTE) for digital services * Charging package dashboard * Steering wheel adjustable in tilt and height * MBUX multimedia system * OM 654 DE 20 LA 110 kW (150 hp) 3800 rpm * Parking package with reversing camera * Premium complete wheel protection (3 years) * Tyre pressure monitoring system front and rear axle, wireless * Signage / instructions in German * Side marker lights * Driver's seat occupancy detection * Driver’s seat heating * Smartphone integration package * Jump start terminal * Upholstery: fabric "Maturin" black * Intelligent Speed Assistant updates * First aid kit * AGM battery 12 V, 92 Ah * Front axle with increased load capacity * Intelligent tachograph EU pre-installation * Navigation pre-installation * Warning triangle * Wet wiper system * Heat-insulating glass with band filter for windscreen * Registration certificate, part II * Axle ratio i = 3.923 * Vehicle without EC speed limiter * Model year 25 Miscellaneous: * Nationwide delivery for €299 net plus VAT (€355.81 incl. VAT) * For all vans: On request, 12 or 24 months Mercedes-Benz used vehicle warranty available. * We are happy to take back your current vehicle, offset it against the new vehicle or pay you the purchase amount. * Leasing / financing options via Mercedes-Benz Bank. We are happy to prepare an offer for you. * No liability for printing & typographical errors * Subject to change and prior sale ----.

Condition: new, mileage: 250 km, power: 140 kW (190.35 HP), fuel type: electric, overall weight: 3,500 kg, tire size: 225/65 R16, axle configuration: 4x2, wheelbase: 3,520 mm, color: white, driver cabin: day cab, gearing type: other, emission class: none, suspension: steel, total length: 6,000 mm, total width: 2,010 mm, total height: 2,620 mm, loading space volume: 12 m³, loading space length: 3,540 mm, loading space width: 1,740 mm, loading space height: 1,900 mm, operation weight: 225 kg, lifting height: 2,623 mm, Equipment: ABS, air conditioning, cabin, cruise control, low noise, onboard computer, traction control, Financing / leasing possible after credit check!, Talk to us!, Errors and prior sale reserved, MY2024 electric panel van wheelbase 3520L mm Comfort Plus package Driving Assistant package ASC wooden floor and paneling ASC lashing rail 3520 & L My Iveco Infot. 10 Nav USB driver / passenger voice assistant Alexa integrated lane centering plus (LC) Sp. Ass. both sides + door lock + AbbA (BSW) intelligent traffic jam assistance (TJA) cross traffic warning rear & brake (RCTA) cargo area light 3 LED storage box driver's seat & USB steering wheel in leather luxury driver's seat, hydraulic battery charged printed matter German 4x2 additional speed limiter trailer socket 12 V, 13-pin AC charging 22 KW fog lights DC charging 80 kW reversing camera dyn. Lines Rear doors Opening angle 260 ASC Wheel arch lining Operating and maintenance instructions Electric mirror Body width 2200 Cat IV Passenger seat with MF storage Switch for body lighting Grab handle on A-pillar Trailer coupling Ball head Number of drive batteries 2 74 kWh Comfort headrests Roof storage above windshield External charging lights above rear doors Seat heating Key Additional remote control Extended partition to the cargo area Distance control ACC Stop & Go Hsdpfxjxa S Iwo Abdei

Condition: excellent (used), Year of construction: 2007, Universal milling machine Manufactured by KUNZMANN. WF 650 Year of manufacture 2007 Technical specifications Manufacturer Kunzmann Type WF 650 Year of manufacture 2007 X-axis 650 mm Y-axis 500 mm Z-axis 450 mm Clamping area 1000 x 600 mm Spindle mount SK 40 Spindle speeds 5 - 6500 rpm Quill stroke 60 mm Vertical head swivels +/- 90 Max. table load 400 kg Feed rates - longitudinal/transverse/vertical 0 - 4000 mm/min Rapid traverse 25 / 25 / 20 m/min Distance between table and vertical milling spindle 100 / 550 mm Distance between table and horizontal spindle 270 / 720 mm Number of tool magazine positions: 20 Tool diameter: 95 mm Tool diameter with 2 free positions: 135 mm Max. tool length: 300 mm Max. tool weight: 7 kg Spindle power: 13 kW Total power requirement: 20 kVA Machine weight: approx. 5.5 t Machine dimensions: L x W x H: 3.80 x 2.70 x 2.40 m Equipment - Heidenhain iTNC 530 control system - Operating instructions Hedewhm S Nspfx Abdoi - Enclosure - Vertical head with extendable spindle sleeve - Hydraulic tool clamping - Fixed table - Electronic handheld control panel - Coolant system - Chip conveyor All information is subject to change without notice. A demonstration is available at any time in our showroom.

Condition: new, Deburring machine Make: Assfalg Hjdpfx Ajb E Dc Hobdsi Model: FS 5 Condition: new machine Speed: 2,800 rpm Max. chamfer width: 3 mm Equipped as standard with: - Guide rail 400 x 50 x 10 mm - Cutter head without indexable inserts - Chip drawer - Operating instructions

Condition: good (used), Indramat RAC 3.1-150-460-A0I-Z1-220 Spindle Drive Controller For sale is an Indramat / Bosch Rexroth RAC3.1-150-460-A0I-Z1-220 AC Main Spindle Drive Controller – used, but in good, working condition. Technical details: Supply voltage: 3 × AC 380–460 V Control voltage: AC 230 V Weight: approx. 49 kg Continuous current: approx. 92 A Max. output power: approx. 55 kW Ambient temperature: +5°C to +45°C (operation), −30°C to +85°C (storage) Hedsxl A Ncepfx Abdji Max. operating altitude: up to 1000 m above sea level. NN Protection class: IP10, humidity class "F" according to DIN 40040 Integrated cooling via fan Integrated emergency stop system Condition: Used (see pictures). Note: For detailed technical specifications and processing instructions, we strongly recommend consulting the original data sheets or contacting the manufacturer directly. Financing through our bank is also possible. komplett-konzept.leasingo.de You can find more items – new and used – in our shop! International shipping costs upon request!

Year of construction: 2023, condition: like new (used), Nordcap Ice Cube Maker with Partial Desalination System This unit comes directly from Miele and has only been used a few times in our test kitchen. Year of manufacture: 2023 For hollow ice cube production Integrated storage container Water-bearing components made of food-grade materials Positive spray system, fully automatic production control Automatic defrosting system (hot gas/fresh water) Soil-prone components removable from the front, pre-installed drain connections Hodpotrd Nzsfx Abdoi Note: A minimum wall clearance of 152 mm must be planned for when installing the unit. ... Partial Desalination System Partial desalination up to 5,600 l with silver-impregnated activated carbon for supplying decarbonized water 0° dH (KH) Nordcap SDE 100 l Connection type: Plug-in Cooling type (machine): Air-cooled External casing: Stainless steel 1.4509, rounded edge protection Inner casing: Polyethylene inner tank, AGION® antibacterial coating, deep-drawn in one piece Self-cleaning system Gross weight: 74 kg Net weight: 63 kg Climate class: 5 (+40 °C ambient temperature and 40% relative humidity) External width: 670 mm External depth: 595 mm External height: 981 mm Year of manufacture: 2023 Refrigerant: R-452A Refrigerant charge: 450 g Electrical connection: 0.83 kW | 230 V | 1 | 50 Hz Output: approx. 100 kg hollow cubes / 24 h Hollow cube dimensions (W x D x H): approx. 35 x 29 x 36 mm Energy consumption: 16.00 kWh/24h List price Nordcap SDE 100 l: €3,789.00 plus VAT List price partial demineralization: €849.00 plus VAT PDF files: Datasheet Operating instructions Declaration of conformity Electrical circuit diagram Financing through our bank is also possible. komplett-konzept.leasingo.de Further items in other sizes – new and used – can be found in our shop! International shipping costs on request!

Condition: used, Year of construction: 2016, TECHNICAL DATA AXES Max. workpiece dimensions X-Y-Z mm 3050 x 800 x 50 Min. workpiece dimensions X-Y-Z mm 300 x 90 x 10 Drilling/slotting working area mm 0 x 800/0 x 800 X axis stroke mm 750 Max. travel speed of X-Y axes m/min 25 DRILLING UNIT Vertical spindles Number 7 (4X-4Y one common) Horizontal spindles (along the Y axis) Number 2 (1+1) Horizontal spindles (along the X axis) Number 1 Fixed grooving saw (direction) X Grooving saw diameter mm 100 Max. grooving saw thickness mm 5 Motor power kW (HP) 1.5 (2) Spindle speed rpm 3350 Grooving saw speed rpm 4300 INSTALLATION Power supply V (Hz) 380 / 400 (50 / 60) Installed power KVA 4.5 Compressed air requirement bar 6 Compressed air consumption Nl/cycle 90 Extraction requirement m3 / h 1200 Extraction air speed m / sec 20 Extraction nozzle diameter mm 80+80 F10L Drilling unit Includes: - 7 independent vertical spindles - Drill chuck D10 mm - Distance between spindles 32 mm - 2 horizontal drilling heads, 1 in X direction with one drill, 1 double drilling head in Y direction (1 + 1 drill chuck D10 mm) - Speed 3350 rpm - 1 integrated sawing unit in X (max. Diameter 100 mm) - Saw blade speed 4300 rpm - Motor power 1.5 kW - Vertical pneumatic travel per spindle 70 mm - Horizontal pneumatic travel of the drilling unit. Positioning of the workpiece and drive of the work unit: A CNC-controlled suction cup clamps the workpiece and positions it sequentially under the work unit during machining. Movement in the X and Y axes takes place on THK guides with transmission to reinforced toothed rails. Movement in the Z axis is pneumatically controlled on ball-bushing guides with adjustable stop positioning. The positioning of the work units is carried out using technology and drives with DC motors. CNC CONTROL The control system was specially developed for use in drilling and milling machines. CN - 7" color screen with touchscreen function - Alphanumeric keyboard - Self-diagnosis and any error messages or malfunctions that may occur, in the operator's language Programming - Programming via the CN - Automatic optimization of drilling operations - Option of plate zero point shift - Option of saving and importing drilling programs via USB dongle - Option of importing drilling programs from CAD-CAM external software Configuration - User interface in the same language as the instruction manual Graphic representation of the unit configuration Vacuum suction cups "B-Power Vacuum suction cups with double vacuum connection, recommended for particularly porous panels (e.g. MDF light). Machine user interface software Xilog Maestro USB Hardware and software requirements: - Operating system: Windows XP Professional (SP2), Windows Vista or Windows 7 - Processor: Intel compatible, 2GHz min; Multicore processor recommended - Memory capacity: 1GB min., recommended 2GB - Free disk space: 5GB - Graphic card: Compatible OpenGL (The code includes a DVD for installation and a USB key) Xilog Maestro Features Programming - Parametric, graphic programming - Assisted programming with graphic and syntax help for drilling operations - Possibility to create and save machining macros Integrated additional functions - Self-diagnosis and possible error messages or malfunctions, in the operator's language - User interface in Hjdpfx Abovvi I Rsdji

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, Measuring range X-axis (tool diameter) approx. 400 mm Measuring range Z-axis (tool length) approx. 400 mm Max. tool weight 10 kg Tool holder/base holder SK 50 Tool adapter SK50 to SK40 with calibrated calibration balls Digital display with operating instructions/manuals Well-maintained tool presetter in very good condition. Hsdpfx Aeylhq Hebdsi

Condition: reconditioned (used), functionality: fully functional, year of last overhaul: 2026, input voltage: 400 V, DGUV certified until: 03/2027, total length: 1,140 mm, overall weight: 285 kg, total width: 800 mm, total height: 1,620 mm, electrical fuse: 16 A, input frequency: 50 Hz, empty load weight: 285 kg, Rego SM 2000 M Beating Machine The machine when it comes to beating! Mixing machine with automatic timer 2 operating modes: 1 x mixing / 1 x beating Manual bowl lift Bowl lighting Connection: 400V, 16A CEE plug Used machine, overhauled with warranty + spare parts service + Quality from a specialist dealer! Benefit from over 35 years of experience! Options: Hjdpfew Tqihsx Abdji New bowl New whisk Ring gas burner Maintenance contract Service package Delivery service Instruction / commissioning Visit our large bakery machines exhibition!

Condition: good (used), functionality: fully functional, input voltage: 400 V, type of input current: three-phase, Deep Fryer Roka / Kippfix T 40-E Frying Station T 40-E easy operation Hedsykh T Sopfx Abdei for approx. 360 pcs/hr. Berliners / donuts 1 frying basket & 1 steam lid drip tray on the right 5 ALU proofing trays robust technology Connection: 400V, 16A CEE plug Used equipment Options: dipping grid maintenance contract spare parts box service package delivery service instruction & commissioning We have many more deep fryers in stock!

Year of construction: 2013, condition: used, We offer you a used PET bottle crusher of the manufacturer BOREMA, type R-1200 F, year of construction 2013, for residual emptying, deaeration and pre-compaction of the fed PET bottles, from 0.3 up to 2.5 l content. The machine has a chassis and can be moved into and out of the feed chute of your baler. The machine has a throughput capacity of approx. 85,000 bottles/h, corresponding to approx. 3t/h. We have the following technical information: Manufacturer: BOREMA Umwelttecjhnik AG Type: R-1200 F (with trolley for retracting and extending) Year of manufacture: 2013 Drive power: 11 kW Connected load: 15 kW Rated current: 32 A Back-up fuse: 40 A Type of construction: Continuous system Function: Double rotor press system Hedpfju Thpnex Abdsi Rotor pretension pneumatic: approx. 16t Overload protection: by anti-blocking system Input material: PET disposable and returnable empty bottles 0.3 to 2.5 L capacity Input material: HDPE bottles and canisters up to 3 l capacity Throughput capacity: approx. 3 t/hour, corresponding to approx. 85,000 bottles/hour, depending on size Required compressed air output: G1/2", 8 bar, 40 l/min. Compression ratio: 1:3 Flange dimensions inside: 972 x 1220 mm Feed opening: 565 x 1280mm Weight: approx. 2500kg Possible applications: Due to the chassis, the PET flattener can be moved into the feed chute of your baler as required, thus ensuring residual emptying, venting and pre-compaction of the fed bottles and canisters. When the material is changed, the PET flattener is simply moved out of the feed chute again and paper, cardboard, film, etc. can now be pressed further without using the flattener. Process of the BOREMA PET crusher: The plastic packages are drawn in by two rotating shafts. One of the rotating shafts is pneumatically pretensioned by two air bellows and presses the PET bottles with 16 t of pressure against the second rotating shaft. In the process, the closed plastic bottle is squeezed together, caused to burst and vented. Residual liquids run out and the material falls into the baler in a precompressed state. When impurities are introduced, the pneumatically pre-tensioned shaft deflects to the side and the impurities are channeled through. Significant advantages compared to conventional PET perforators with punching mandrels or knives: The BOREMA process is much more efficient and less subject to wear than conventional PET perforators with punching mandrels or knives. The biggest advantage is that any foreign matter such as metal parts, stones, bottles with frozen contents and pieces of wood are passed through the pneumatically deflecting rotor shaft without stopping the operation of the system or causing any major damage. With conventional perforators, mandrels or blades sometimes break off or become so jammed with the interfering material that the plant has to be shut down and repaired at great expense. Comments: The crusher is in good condition, was dismantled from the running operation, stored, is available at short notice and after assembly immediately ready for use. The documentation (manual, CE, electrical/hydraulic circuit diagram) is complete. An inspection is possible by arrangement. The technical information is taken from sales brochures, the operating instructions or other information provided by the manufacturer. We accept no liability for incomplete or incorrect data and informations.

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Hedpfx Abeu Tg I Dedji Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: fully functional, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Hodpfx Aeu Thh Eobdoi Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating instructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 1979, roll diameter 420 mm throat 410 mm workpiece height 265 mm saw band length 3150-3260 mm width of saw-band max. 16 mm table-size 600 x 600 mm work height max. 1000 mm total power requirement 1,1/1,7 kW weight of the machine ca. 0,51 t dimensions of the machine ca. BTH 740x920x1815 mm - Includes welding equipment Hodpfxeyg Raae Abdji - Includes grinding equipment - Includes work light - Includes semi-hydraulic weight feeder - Includes tilting work table - Includes operating instructions

Condition: used, Year of construction: 1980, x-travel 300 mm y-travel 160 mm z-travel 340 mm tool taper SK40 Speed 40-2000 U/min. control Aktiv HEIDENHAIN Hodpfx Abew A Apysdji table-size 600 x 210 mm total power requirement 2 kW weight of the machine ca. 0,73 t dimensions of the machine ca. TBH 1200x1100x1600 m - Active feed in the X and Z axes - Additional swiveling table 600 x 210 mm - Coolant system - Counter bearing for horizontal milling - Several fixtures and clamping devices/milling cutters - Operating instructions

Condition: used, Year of construction: 1980, x-travel 300 mm y-travel 160 mm z-travel 340 mm tool taper SK40 Speed 40-2000 U/min. control Aktiv HEIDENHAIN table-size 600 x 210 mm total power requirement 2 kW weight of the machine ca. 0,73 t dimensions of the machine ca. TBH 1200x1100x1600 m - Active feed in the X and Z axes - Additional swiveling table 600 x 210 mm - Coolant system Hodpfx Absw A Ap Hedsi - Counter bearing for horizontal milling - Several fixtures and clamping devices/milling cutters - Operating instructions

Year of construction: 2008, condition: ready for operation (used), overall weight: 3,800 kg, spindle speed (max.): 600 rpm, number of axes: 5, This 5s SAACKE UWIF cylindrical grinding machine was manufactured in 2008. It features a maximum spindle speed of 600 rpm and a powerful grinding spindle peak power of 16 kW. The machine supports a variety of workpiece sizes, with a maximum diameter of Ø 20 mm and a weight capacity of 1 kg. If you are looking to get high-quality grinding capabilities, consider the SAACKE UWIF cylindrical grinding machine we have for sale. Contact us for further details. • Workpiece carrier A-axis: Direct drive/hollow shaft motor; indexing accuracy ±15"; indexing possibilities 1–999; cumulative pitch error at 100 mm: 8 µm; speed max. 600 rpm • Tool holder: ISO 50 • Spindle clearance holding sleeve: max. 28 mm (with automatic clamping: Ø20 mm) • Nominal drive power: • Grinding spindle S1-100%: 7.5 kW; peak: 16 kW • X-axis longitudinal travel: 2 kW • A-axis workpiece carrier: 2 kW • Z-axis cross slide: 2 kW • Y-axis grinding head slide height: 2 kW • B-axis grinding head rotation (rotary table): 2 kW • Position measuring systems: • A-axis: Direct measuring system • B-, X-, Y-, Z-axis: Indirect measuring system • Resolution X/Y/Z: 0.0001 mm (0.1 µm) • Resolution A/B: 0.0001° • Electrical connection: 20 kW / 50 A; operating voltage 400 V, 50 Hz; control voltage 24 V; lighting voltage 230 V; backup fuse: separate supply from mains Hsdpfx Abjyiz R Uodei • Compressed air: 15–17 Nm³/h; pressure min/max 6/8 bar (600/800 kPa); quality ≥ Class 4 (ISO 8573-1) • Control & software: CNC NUM Axium Power 1050 with PC, program memory 512 k; NUMROTOplus software (dongle/hardlock required); zero points calibrated using enclosed measuring instructions (no marked reference points) Additional equipment • Workpiece changer options (automation): • Option 1: Pick-up design • Max. workpiece: Ø20 mm × 120 mm; 1 kg • Capacity per pallet: • Ø3.0–5.0 mm shank: 40 pcs • Ø5.1–8.0 mm: 32 pcs • Ø8.1–11.0 mm: 28 pcs • Ø11.1–14.0 mm: 24 pcs • Ø14.1–20.0 mm: 20 pcs • Option 2: Chain loader magazine (with gripper unit) • Capacity: 64 workpieces • Max. workpiece: Ø32 mm × 200 mm; 2.5 kg • Features: Chaotic loading of different workpieces; automatic changing of collets possible • Holding sleeves: Ø6, 8, 10, 12, 14, 16, 20 • External chain loader option: increases machine weight to approx. 3,800 kg and space to 3,000 mm × 1,875 mm • Coolant filter system (TRANSOR): To be provided by customer; air for backwashing approx. 700 Nl/min for 5 min every 6–9 hours

Condition: used, functionality: fully functional, Year of construction: 2023, operating hours: 6 h, load capacity: 240 kg, empty load weight: 920 kg, construction height: 1,990 mm, fuel type: electric, drive type: Elektro, working height: 5,600 mm, Scissor lift Condition: As good as new Technical condition: New Front tires Type: Non Marking Front tires Condition: New Rear tires Type: Non Marking Rear tires Condition: New Battery Volt: 24V Battery Ah: 85Ah Battery year of construction: 2023 Hsdpfx Aswu Itbebdsi Battery Condition: New Description: Condition: Demo unit - checked - according to FEM 4.004 (UVV). English: Demo unit - checked - without any warranty. Subject to prior sale. Documentation: Operating instructions and test book Rental - also long-term rental - possible at favorable conditions! Please contact us. Sale only to traders (without warranty). Subject to prior sale and prior rental. Our general terms and conditions apply. The price quoted is exclusive of VAT. max. load capacity: 240 kg extended load capacity: 100 kg max. number of persons: 2 indoors max. number of persons: 1 outdoors Total length: 1.44 m Total width: 0.76 m Total height (railing unfolded): 1.99 m Working height: 5.6 m Working platform height: 3.6 m Working platform length: 1.29 m Platform width: 0.70 m Platform extension: 0.60 m Ground clearance (stowed): 6 cm Ground clearance (raised): 1.50 cm Wheelbase: 1.05 m Drive: electric drive Turning radius (inside): 40 cm Turning radius (outside): 1.55 m Travel drive: 2 x 24VDC/0.4kW Lift drive: 24VDE/1.2 kW Speed (retracted): 4 km/h Speed (extended): 0.60 km/h Battery capacity: 24 V / 85 Ah Integrated charger: 24 V / 10 A Gradeability: 25% Max. Inclination: 1.5°/3° Features: - automatic pothole protection - anti-trap protection - generous ground clearance - self-locking door - speed limitation at maximum lifting height - overload control - automatic braking system - emergency brake solution - inclination control with warning message - acoustic lowering alarm and double LED flashing light - safety bar for maintenance work - horn - cylinder lock valve - emergency stop button - emergency lowering - protection of the drive motor - stop eyes - on-board diagnostics lifting eyes - on-board diagnostics - operating hours counter - proportional control - foldable railing - power supply on the platform - maintenance-free batteries - explosion-proof wiring system - movement alarm - integrated pockets for transport with forklift truck - load protection system - load indicator - stop and lifting points - single-sided extendable workman basket - two-wheel drive - two-wheel steering - manual emergency brake solution

Condition: used, mileage: 175,540 km, power: 130 kW (176.75 HP), first registration: 03/2020, fuel type: diesel, overall weight: 3,500 kg, next inspection (TÜV): 03/2026, color: white, gearing type: mechanical, emission class: euro6, number of seats: 2, loading space length: 4,300 mm, loading space width: 2,150 mm, loading space height: 2,300 mm, Year of construction: 2019, Equipment: ABS, air conditioning, central locking, INTERNAL VEHICLE NUMBER: M521 ----VW CRAFTER 2.0 TDI XXXL BOX BODY----KM: 175,540 WITH SERVICE BOOK DIGITAL VEHICLE HISTORY AVAILABLE LAST INSPECTION WITH OIL CHANGE AT 175,115 KM ON 23.09.2025 ALL INSPECTIONS PERFORMED AT MANUFACTURER-AUTHORIZED WORKSHOP DIGITAL VEHICLE HISTORY AVAILABLE----1 OWNER ----M+S TYRES----* HILL START ASSIST * BRAKE ASSIST * CROSSWIND ASSIST * AIR CONDITIONING * REVERSING CAMERA * AUTOMATIC HEADLIGHT ADJUSTMENT * START/STOP SYSTEM ----PAYLOAD: 1,050 KG CURB WEIGHT: 2,450 KG GROSS VEHICLE WEIGHT: 3,500 KG ----XXXL BOX BODY WITH RAMP BY RAPID LEICHTBAU GmbH BOX DIMENSIONS: LENGTH: APPROX. 4.30 METRES WIDTH: APPROX. 2.15 METRES Hedpfxeynraqs Abdsi HEIGHT: APPROX. 2.30 METRES SIDE WALL WITH LASHING RAILS----WHEEL ARCH DIMENSIONS: LENGTH: APPROX. 1.15 METRES WIDTH: APPROX. 0.45 METRES HEIGHT: APPROX. 0.35 METRES----SPECIAL LOADING RAMP FOR TROLLEY LOADING----REAR AIR SUSPENSION BY VB AIR SUSPENSION, FITTING INSTRUCTIONS INCLUDED---- * MULTIFUNCTION STEERING WHEEL * BLUETOOTH HANDS-FREE SYSTEM * APPLE CARPLAY * ANDROID AUTO * USB * AUX * SD CARD * MULTI CD CHANGER * ERGO COMFORT SUSPENSION SEAT * 2 X ARMRESTS * ELECTRIC WINDOWS * ELECTRIC HEATED MIRRORS * REMOTE CENTRAL LOCKING * 2 SEATER * CARGO AREA LIGHTING ON/OFF * LUMBAR SUPPORT * ROOF SPOILER * MARKER LIGHTS ----Special equipment: * Audio system Composition Media (Radio/CD player, MP3 playback) * Light & Vision package * Electric adjustable and heated exterior mirrors * Reinforced battery * Chassis: reinforced dampers and stabilisers at front and rear * Vehicle without model designation * Multifunction steering wheel * Side marker lights * Smoker package * Reversing camera * Front mud flaps * ErgoComfort suspension driver’s seat * Driver’s seat 20-way adjustable Additional equipment: * Driver airbag * Left convex exterior mirror * Right convex exterior mirror * LED indicators integrated in exterior mirrors * Cab flooring: rubber * On-board tools * Drag coefficient underbody panelling * Double headlights * Dual-tone horn * Entry handle, rear left pillar * Entry handle, rear right pillar * Hill Start Assist * Brake Assist (HBA) * Crosswind Assist * Front electric windows * Laminated windscreen * Folding remote keys (2) * Grab handles A-pillars * Interior LED lights: cab * Interior LED lights: cargo/FG area * Fuel tank: 75 Ltr. * Headlight range adjustment * Truck registration * Engine 2.0 Ltr. - 130 kW TDI * Wheelbase 3,640 mm * Tyre repair kit * Low emissions to Euro 6 standard * SCR system (AdBlue technology) * Electro-mechanical power steering * Seat trim/upholstery: fabric * Passenger seat adjustable * Engine Start/Stop system * 12V sockets in cab (2 units) * Front bumper in grey with body-colour trim * Tie-down rings in cargo area * Seatbelt warning (driver’s side) * Heat-insulating glazing * Central locking with remote and internal operation * Permissible gross weight 3.50 t ----Upon request, we can retrofit the vehicle with a tow bar. Professional installation – fast and reliable, from €599. +++ Exclusive promotion at Autohaus Mat GmbH: Up to €1,000 trade-in bonus – your benefit for switching vehicles! +++ Contact us directly via WhatsApp

Condition: ready for operation (used), Year of construction: 2019, number of axes: 3, This 3-axis SAFAN Darley E-Brake Premium press brake was manufactured in 2019. It features a CNC-controlled servo-electronic system with Y1/Y2, X, and R axes, and a stroke of 300 mm. The EC10 control system supports multiple file formats and includes safety equipment compliant with European directives. Ideal for precise bending operations, consider the opportunity to buy this SAFAN Darley E-Brake Premium press brake. Contact us for more information about this machine. • Control and software: • EC10 control with split-screen on a height-adjustable swivel arm • SafanDarley EC Control with center-mounted swivel arm (operation from either side) • Displays DWG, DXF, PDF, JPG, PNG, BMP, WMV • German language instructions and HMI • EC20 software package for EC10 split-screen incl. EC Profiler with 2D bending simulation • Automatic bend sequence calculation and graphical representation for AutoPol and Radan files • Axes and travels: • CNC-controlled Y1/Y2 (stroke 300 mm) Hsdpsx Np Ehefx Abdei • CNC-controlled X-axis • CNC-controlled R-axis • CNC-controlled Z1+Z2 (Type G) with programmable independent lateral adjustment of backgauge fingers • CNC-controlled dX-axis on Z2 finger, 100 mm stroke (+/- 50 mm), with hardened 3D backgauge cams • Enlarged installation dimension Q = 650 mm, stroke 300 mm • Tooling and clamping: • NSCL-II HC Premium upper tool adapter with hydraulic clamping, hardened surface, incl. hydraulic unit • Upper tool working height 80 mm; clamping length 1275 mm • OB II HC Premium mounting table with adjustment wedge, hydraulic clamping, hardened surface • Mounting table size 110 x 87 x 1275 mm, incl. hydraulic unit • Measurement: • E-Bend S sheet thickness measurement at the Z1 backgauge finger • Safety and lighting: • CNC-programmable safety light curtain • Safety equipment compliant with EU Machine Directive MRL/2006/42/EG • Front-side work area lighting and rear-side tool lighting • Ergonomics (machine-integrated): • Ergonomic package: lower beam with legroom recess and tilted footrest • Foot pedal usable on the footrest or on the floor • Identification and logistics: • Customs tariff number: 8462 2110 • Main machine weight: 3250 kg; dimensions: 2330 x 1809 x 2649 mm • Secondary pallet: 90 kg; 1300 x 800 x 900 mm Additional equipment • Ergonomic table system: central segment (height and tilt adjustable) and left/right segments (height adjustable) • Adjustable chair with seat, footrest, and backrest adjustment on swivel casters • Left-side material cabinet with five height-adjustable shelves

Condition: ready for operation (used), Year of construction: 2007, This TRUMPF TruBend V5050 press brake was manufactured in 2007. It features a press force of 500 kN and a bending length of 1275 mm. Equipped with a stable machine frame, electro-hydraulic upper drive, and a 2-axis backgauge system, it ensures precision and efficiency. Ideal for high-quality bending operations. Contact us for more information about this machine. Additional equipment • Stable machine frame as a welded construction in all-steel construction / Pressure beam with high bending strength / Spherical bearing of the pressure beam with pressure beam inclined position / Electro-hydraulic upper drive with 2-cylinder technology / Proportional valve technology and switchable double pump / Modern block hydraulics with control valves mounted on the cylinder / Electronic pressure compensator / Measuring system with centrally mounted glass scales and temperature compensation / Upper tool holder system "New Standard Clamping" manual, hardened, self-centering, for vertical tool changes / Lower tool holder with hydraulic clamping, hardened / Programmable lower tool displacement (pneumatic, 2 positions) / 2-axis backgauge system with rack and pinion drive for X and R axes, 2 stop fingers with secure front adjustment / Machine control: TRUMPF TASC 6000 / Control panel with LCD keypad, foot switch for emergency up, down, and emergency stop / Safety device: integrated side doors / Control cabinet cooling (air-to-air heat exchanger) / Oil cooler / Network-capable / Modern machine design / Installation, commissioning, and instruction / Hydraulic upper tool clamping / BendGuard / TruBend documentation Machine Benefits Technical Machine Benefits • Press force: 500 kn Hedpfx Aox D Hb Hobdoi • Bending length: 1275 mm / free column clearance: 1040 mm / installation height: 385 mm • The machine was serviced annually by trumpf. • Trumpf maintenance contract.

Condition: new, Moog Servovalve Unit D665-5703 & D661-5623C High-Performance Valve Module For sale is a fully functional, industrially used, high-performance servovalve unit from MOOG, consisting of two perfectly matched valves. Also available as individual components! Moog D661-5623C – High-Response Valve Technical Specification Value Model Designation D661-5623C Type Code G18H0A0NSA0HP Valve Type 4-Way, 2-Stage with Bushing Spool Nominal Flow 120–200 l/min (depending on version) Operating Pressure P, A, B Max. 350 bar Return Pressure T (internal) 210 bar Return Pressure T (external) 280 bar Hsdpfxjxltkks Abdei Control Pressure 25–350 bar Coil Stroke ±0.13 mm Control Area (AK) 1.35 cm² Operating Time (0–100%) Approx. 14 ms Hysteresis < 0.6% Zero Offset < 1% Supply Voltage ±15 V DC Input Signal ±10 V Protection Class IP65 Weight approx. 5.7 kg Connection diagram ISO 4401-05-05-0-94 Moog D665-5703 – High-Performance Valve Technical property Value Model designation D665-5703 Type code K15HXJW4NSM0-P Valve type 4-way, 3-stage, ServoJet Nominal flow rate 1500 l/min Δp = 5 bar per control edge Operating pressure P, A, B max. 350 bar Return pressure T (internal) max. 100 bar Return pressure T (external) max. 280 bar Control pressure min/max min. 25 bar above T / max. 350 bar Control spool stroke ±8 mm Control area (AK) 9.6 cm² Hysteresis < 0.2% Zero offset (55K ΔT) < 2% Zero leakage current (total) max. 11 l/min Supply voltage ±15 V DC Input signal ±10 V Protection class IP65 Weight approx. 73.5 kg Connection diagram ISO 4401-10-08-0-94 Connections X and Y external (ServoJet required) Description & Use: Condition: New (see pictures). Note: For detailed technical specifications and processing instructions, we strongly recommend consulting the original data sheets or contacting the manufacturer directly. Financing through our bank is also possible. komplett-konzept.leasingo.de You can find more items - new and used - in our shop! International shipping costs upon request!

Condition: reconditioned (used), functionality: fully functional, year of last overhaul: 2026, input voltage: 400 V, DGUV certified until: 03/2027, total length: 750 mm, overall weight: 285 kg, total width: 640 mm, total height: 1,650 mm, electrical fuse: 16 A, input frequency: 50 Hz, empty load weight: 285 kg, Rego SM 4 RMT Beating Machine – Refurbished Hedpfoxiu Hzjx Abdei Rego model: SM 4 RMT, refurbished Mixer with automatic timer The machine of choice for beating tasks! 2 working functions: 1 x mixing / 1 x beating Drive shaft / mixing shaft newly overhauled Powerful and robust technology Bowl illumination, timer switch Connection: 400V, 16A-CEE plug Refurbished used machine with warranty and spare parts service Quality from a specialist workshop! Benefit from over 35 years of experience! Options: Additional accessories Ring gas burner New bowl New whisk New mixing paddle Rotary ring / bowl ring Maintenance contract Service package Delivery service Commissioning & operational instruction Come visit us!

Condition: excellent (used), functionality: fully functional, input voltage: 400 V, DGUV certified until: 03/2027, cutting width (max.): 25 mm, type of input current: three-phase, total length: 700 mm, total width: 905 mm, total height: 500 mm, nominal power: 1 kW (1.36 HP), input frequency: 50 Hz, year of last overhaul: 2026, space requirement height: 500 mm, space requirement length: 700 mm, space requirement width: 905 mm, power: 1 kW (1.36 HP), Bread slicer MHS Ideal L Stainless steel construction Bread slicing machine with NEW blade Manual operation via membrane keypad DGUV V3 safety check – only with us Connection: 400V, 16A CEE plug Dimensions: 905 x 700 x 500 mm (W x D x H) Used machine, cleaned With warranty and spare parts service Quality from a specialist company! Benefit from over 35 years of experience! Options: Spare blades Mobile base Blade service Maintenance contract Delivery service Service package Hsdpfx Aoxyquiebdoi Instruction & commissioning Many more bread slicers in stock!